Search Documents

By James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limestone-dolomite beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Jan 1, 1965

By James J. Snodgrass

The Bureau of Mines designed and constructed a series of calibration models for geophysical borehole logging. A nominal hole diameter of 3 inches was selected as representative of typical core holes drilled for mining and engineering purposes, although additional hole diameters of 2, 5, and 8 inches are provided in one of the models for determination of empirical correction factors for variations in hole diameter. The physical properties of the models were determined by laboratory analyses of drill core samples and evaluated statistically for reliability. This report outlines the location of the models, elements of design and construction, and results of the laboratory tests. The models are available at the Denver Federal Center, Denver, Colo., for use by Government agencies and private industry to calibrate logging equipment for measurements of density, sonic velocity, magnetic susceptibility, and electrical resistivity.

Jan 1, 1976

By Paul M. Tyler

The enormous deposits of greensand in New Jersey and elsewhere in the United States, many of them close to important octant industrial centers, constitute a perpetual challenge for research chemists to convert them into a commercial asset of national importance. Following the introduction of more concentrated fertilizers, comprising synthetic mixtures of more soluble salts, the quantity of greensand used directly upon the soil has diminished, but deposits of such material still have at least potential value locally for use not only as fertilizer but also as a water softener. An annotated bibliography of the already extensive Literature on greensand, virtually complete to about the end of 1929, has been issued by the Bureau of Mines3/, and the commercial aspects as well as the technology of greensand utilization are discussed in available publications, The purpose of the present circular, therefore, is merely to provide a brief outline of certain general essential considerations for use in appraising the potential value of a greensand deposit in any given locality.

Jan 1, 1934

By D. G. Kuehn

Mass spectrographic studies have been conducted on the positive ions and neutral species of glow discharges containing 1.0 pct S02 and 1.0 pct CO in helium. Measurements were conducted for gas pressures from 3.5 to 10.1 torr using both dc and 60-Hz ac excitation. The ion species that were observed included S+, SO+, SO+, 0+, O2+, C+, CO+, and CO2+ with lesser amounts of SO3+, (CO)2+, SCO+, and (SO?CO)+ or CS+2. Interpretation of the functional dependence of the various ionic and neutral species on pressure and applied power showed that CO reacted with the SO formed in the discharges to produce CO2 and sulfur. Deposition of elemental sulfur was observed in the plasma container.

Jan 1, 1973

By Samuel P. Polack

This report reviews investigations to determine the fire hazard in coal mining when using flammable petroleum hydraulic oils to actuate mining equipment and summarizes research by the Bureau of Mines and industry on fire-resistant hydraulic fluids. Tests were established to evaluate fire resistance and the necessary characteristics to assure adequate service when fire-resistant fluids are used to replace petroleum hydraulic oils. The research was conducted in the laboratory and field trials under actual operating conditions in underground mines. Bureau of Mines Schedule 30 became effective December 17, 1959; the first approval was granted on February 18, 1960, and the twelfth was granted on March 17, 1961. The approvals include nine ready-mixed (by the producer) fluids and seven concentrates to which water is added by the user according to instructions from the producer. Seven synthetic-type fire-resistant hydraulic fluids submitted by two producers are also approved. Over 100 coal mines are now using water-in-oil emulsion-type fire-resistant hydraulic fluids in varying degrees from a trial in one machine to all the hydraulic equipment in an entire mine.

Jan 1, 1961

By Foster Fraas

In the separation of a component from a mixture , two fractions are obtained , one containing a high - percentage composition of the component and the other a low - percentage composition . The high - percentage fraction is frequently called the concentrate and the low - percentage fraction the tailing . In many separation processes the recovery is not complete , and the composition of the concentrate decreases as the recovery of the component, which is concentrated , increases . It is this particular class of separations to which this paper is confined .

Oct 1, 1942

By W. C. Holliman

This second of a series of reports on the characteristics of commercial aviation gasolines presents inspection test data furni8hed on their products by 15 manufacturers of commercial grades of aviation gasoline and special data obtained in Bureau of Mines laboratories on samples of these gasolines. Data on 18 grade-80, 20 grade-91/98, 20 grade-100/130, and 9 grade-115/145 aviation fuels are presented. These gasolines represent July 1947 production.

Jan 1, 1948

By R. O. Kneisley

Rock mechanics measurements indicate that the present two-bed mine design used at the Big Island trona mine, Green River, Wyo., results in stable workings. Vertical pressure changes in the lower panel pillars and horizontal pressure changes in the lower bed roof and floor indicated negligible upper bed mining influence. Pillar stresses stabilized soon after upper bed mining was completed. Strata movements in the pillar ribs, roof, and floor were also negligible and stabilized soon after completion of upper bed mining. Using tributary area theory, the confined core approach, and studies of model trona pillars it is shown that increased extraction ratio is possible. A program of gradually increased extraction ratio accompanied by simple measurements should result in a mine design that includes both higher recovery and long-term stability.

Jan 1, 1981

By D. G. Lee

Diesel particulate matter (DPM) often contains small amounts of metal as a minor component but this metal may contribute to adverse health effects. Knowledge of the mechanism for particle formation as well as the size preference of the trace metals is critical to understanding the potential for health concerns. To achieve this, the size and the composition of each particle should be optimally measured at the same time. Single particle mass spectrometer (SPMS) would be the best tool for this objective. In this paper, we therefore will introduce new findings about the mechanism and distribution of the trace metals in DPM, derived from a study where an SPMS was used to analyze freshly emitted DPM. KEY WORDS : Single particle mass spectroscopy, Diesel particulate matter, Characterization, Metal contents

Jan 1, 2006

By Raymond L. Carpenter

The thermal conductivity, electrical resistivity, and Seebeck coefficient for nine compounds, based on the formula for enargite Cu3AsS3, were measured in a search for efficient materials to be used in thermoelectric generators or refrigerators. Results indicate that one of these compounds, Cu3SbSe4, has thermoelectric properties approaching those of bismuth telluride. An investigation of the effect of adding small quantities of tellurium to Cu3SbSe4 and Cu3SbS4 in order to improve their properties also was made. A figure of merit of 2.1 x 10-4 °C-1 was obtained for Cu3SbSe4 + 0.1 percent tellurium.

Jan 1, 1963

By Frank D. Lamb, D. A. Woodard

"INTRODUCTION The iron-ore deposits near Cranberry, N. C., were worked as early as 1820, and records show that to date at least 1,500,000 tons of ore has been mined.. The early operators depended on selective mining and hand cobbing to yield a product containing 40 to 50 percent iron. Later, a magnetic concentrator was erected by the Cranberry Furnace Co. and was operated periodically until 1930. The magnetic cobbing method employed yielded satisfactory concentrates, but the plant was shut down because costs were too high. 4/Early in 1944, in connection with the sponge-iron program of the Bureau of Mines, North Carolina and Tennessee were surveyed for the purpose of finding a readily available source of high-grade iron ore for use in the experimental production of sponge iron at Salisbury, N. C., and samples from various sources were tested in the laboratory. The Cranberry ore proved to be best with respect to grade of magnetite concentrates produced, and it was decided that a pilot mill should be built on the Cranberry mine property and that the concentrate made there should be shipped to Salisbury for direct-reduction tests in a commercial brick kiln."

Dec 1, 1946

By D. K. Deardorff

The hafnium-vanadium phase diagram was constructed within an estimated accuracy of ± 10° C and ± 2 wt pct composition. Alloys for investigation were melted under an atmosphere of purified helium by nonconsumable tungsten-electrode arc melting on a water-cooled copper hearth. Melting points were determined by optical pyrometer, and the remaining phase relationships were investigated by metallography, thermal analysis, and X-ray diffraction. The existence of a face-centered cubic intermetallic compound HfV2 (a = 7.38 A) was confirmed. A eutectic reaction occurred at 20 wt pct vanadium and 1,395° C to yield HfV2 and 8 solid solution. HfV2 melted incongruently by a peritectic reaction at 1,480° C, and the 3 solid solution decomposed eutectoidally at 1,165° C and 6 wt pct vanadium to yield HfV2 and a solid solution. The eutectoid, the eutectic, and the peritectic isotherms extended from 1 to 36.3 wt pct vanadium, from 8 to 36.3 wt pct vanadium, and from 26 to 89.5 wt pct vanadium, respectively. Terminal solid solubilities of hafnium in vanadium at 1,300° C and of vanadium in hafnium at 1,100° C determined to be about 3 and 1 wt pct, respectively.

Jan 1, 1965

By Jeffrey H. Welsh

This report presents a study on the use of computerized, continuous remote monitoring systems for fire and explosive atmosphere safety in underground coal mines. The effects of these systems on the safety level in mines are investigated, and the relationship between mine safety regulations and computerized, continuous, remote monitoring is analyzed.

Jan 1, 1982

By E. A. Loria

High-quality sheet of electrowon molybdenum was attained by a sequence of procedure on pressed and arc-melted crystalline powders. The procedures included high-temperature, high-vacuum sintering treatments and the use of metal deoxidizers instead of carbon to improve the mechanical properties of the molybdenum sheet. Rolled sheet 60 mils thick was evaluated by tensile and bend tests, hardness measurements, microstructures, and recrystallization treatments. After stress relieving, yield strength ranged from 85,000 to 110,500 psi (0.2- percent offset) and ultimate strength ranged from 87,200 to 117,250 psi with 4.5- to 25-percent elongation observed for arc-melted sheet, and 5.0- to 23- percent elongation observed for powder metallurgy sheet. In room temperature bend tests the sheet yielded plastically, indicating that the ductile-brittle transition point was below room temperature. The diamond pyramid hardness (DPH) of the molybdenum sheet changed from 214 to 293 DPH for the stress-relieved condition to 177 to 185 DPH for the fully recrystallized condition. The brittleness of recrystallized molybdenum, reported by other investigators as characteristic of sheet prepared from commercial-grade hydrogen-reduced powders, was not in evidence. Recrystallized tensile specimens pulled at room temperature had an average elongation of 31 percent.

Jan 1, 1966

By J. E. Gebhardt

External control of the electrochemical potential of a bed of mineral particles has been investigated by the Bureau of Mines as a method for controlling particle inter-action with organic collectors and thus, flotation response. A cylindrically shaped, 200-to 300-g bed of sulfide mineral particles was used as the working electrode to examine the potential distribution in the bed. The dissolved oxygen concentration of the electrolyte had a significant effect on the potential profile across the mineral bed. Low oxygen levels were necessary to achieve uniform electrochemical potential distributions. Flotation separation of a chalcocite-pyrite mineral mixture by controlled potential was achieved using ethylxanthate, but the flotation behavior of chalcocite and pyrite from the mixture does not follow the flotation behavior of the individual minerals. That is, the presence of another sulfide mineral alters the flotation behavior with ethylxan-thate. Galvanic interaction due to mineral-to-mineral contact between chalcocite and pyrite contributes to differences in the recovery. Chalcocite dissolution products had a deleterious effect on pyrite flotation by activating flotation below -0.1 V (saturated calomel electrode) and depressing flotation above -0.1 V. Pyrite dissolution products had no effect on chalcocite flotation.

Jan 1, 1985

By John E. Pahlman

An increasing number of gold and silver mining operations are employing cyanide solutions to effectively dissolve silver and gold from finely disseminated ores. Many of these operations use small, packaged processing systems like the State of Maine filter system, which employs zinc precipitation of gold and silver. Solution-clarifying filters in these systems become blinded with calcium carbonate (CaC03) scale and require frequent (every 2 to 10 days) dismantling of the filter units for acid cleaning, This is a hazardous operation as it is not compatible with the alkaline cyanide leach solutions and may result in the evolution of toxic hydrogen cyanide (HCN) gas during cleaning and during any accidental acid spill. The Bureau of Nines has investigated an alternative, nonacidic method of cleaning blinded State of Maine filters that employs ethylene- diamine-tetraacetic-acid (EDTA) type chelating agents to dissolve the scale. In situ cleaning of a 150-st/d State of Maine filters with EDTA- type chelating agents was successfully demonstrated. Greater than 90 pct of the CaC03 scale was removed in about 10 min with circulation of 31 L of 2.5-pct-EDTA solution through the filter unit. The EDTA cleaning method not only eliminates the cyanide hazard in filter cleaning but is advantageous from the standpoint of operating costs and productivity.

Jan 1, 1986

This report is the first in a "final" series of publications on the Juneau Mining District (JMD). This volume summarizes the results of Bureau of Mines (Bureau) investigations in the JMD during the period 1984-1988. Volume 2 consists of a detailed description of Bureau investigations of mineral de-posits, prospects, and occurrences. Volume 3 is a report on industrial minerals within the district. This study has identified and examined more than 300 mines, prospects, and occurrences containing gold, silver, copper, zinc, lead, nickel, cobalt, tungsten, molybdenum, chromium, and PGM. More than 20 of these were discovered during this study. An additional 20 prospects not mentioned in the literature were rediscovered during the JMD study.

Jan 1, 2012

By L. C. IlsLey

[In 1922 a conference of representative coal-mine operators, cable manufacturers, mining-machine manufacturers, and representatives of the United States Bur eau of Mines vas held at the Pittsburgh Experiment Station, regarding suitable cables for use with permissible raining machines. This conference recommended that the Bureau investigate rubber-sheathed trailing cables in order to obtain specifications for tests leading to approval for rise with mining machines. Effective until such time as an investigation could be made, the bureau asked the several manufacturers of approved mining machines to recommend cables for wise with their machines. In general the Cables recommended tentatively approved. Arrangements for the tests were completed in 1927. Concentric-type cables were investigated first, and Reports of Investigations, Serial No. 2909, covering the tests, was issued in January, 1929.]

Jan 1, 1929

By Karl-Heinz Frohne

This report presents the findings of a study of a portion of the Clover-Rush Run oilfield located in Roane County, W. Va. The study was made to investigate the possibilities of secondary oil recovery in the Big Injun sandstone underlying the William Kaufman lease. Reservoir properties, original reserves, and primary oil recovery are also presented. The investigation is based on a core analysis and related laboratory tests, well records, field production data, and subsurface information from the Kaufman property. A theoretical primary oil recovery of 9.7 percent of original oil in place is predicted for the reservoir. A waterflood performance prediction of a hypothetical pilot area was made by use of a computer. The prediction showed that, based on laboratory oil water relative permeability curves, the water-injection time needed to initiate oil production is excessive and that the stabilized water-injection and corresponding oil-production rates are very low. This precludes waterflooding the reservoir on an economic basis. A prediction for secondary oil recovery by gas injection was attempted but could not be completed because essential reservoir data were not available. In July 1965, the lease operator initiated, and is currently conducting, a gas-injection program, but there had been no increase in oil production up to November 1966.

Jan 1, 1967

By D. Harrington

"In at least three out of every four working faces in metal mines there is no attempt made to cause air circulation other than by use of compressed air, and in at least nine cases out of ten the compressed air is released merely by opening, or partly opening, the valve and allowing the compressed air to escape through open air hose used to convey the compressed air to the drilling machines. Usually no blowers are in use during periods of drilling, as the exhaust from the drill provides cool, comparatively fresh air for the driller; however, in some instances, the compressed-air line is provided with a tea connection, which permits taking air for the drill from one side of the tee, and air for ventilation through a separate hose used as a blower, simultaneously with drilling.Table 1 contains temperature and humidity data as to compressed-air blowers from open end of air hose at 36 working places in eleven metal mines of four States, embracing the mining of gold, silver, copper, lead and zinc ores, and at horizons ranging from 500 feet below the surface to as low as 4900 feet.It is noticed that the ordinary air surrounding the worker at the face gives an average wet bulb temperature of 81.7° F. for the 36 working faces, with 84.7° F. dry bulb and 87.2 per cent relative humidity. The average wet bulb tem¬perature of 36 readings at these working faces of compressed air at the end of the,hose as the air issues from the hose was 67.4° F., or 14.3 degrees lower than the average wet bulb readings of the air of the working places; however, the average dry bulb temperature of the 36 readings of compressed air as it issued from the end of the hose was 79.7° F., or only 5 degrees less than that of the general air (84.7°); the relative humidity was 51.1 per cent as against 87.2 per cent for the surrounding air. Readings were taken in five raises, seven crosscuts, ten drifts and 14 stopes.It will be noted that the velocity or movement of the general atmosphere at each of the entire 36 working faces, was found to be practically imperceptible; this might readily be inferred since compressed air is rarely used on blowers if there is adequate circulation of the general air of the place. Where rook temperatures could be obtained readily, they are shown; it is noticeable that the dry bulb temperature of the air of the working place varies little from the rock temperature, and that the dry bulb temperature of the compressed air as it issues from end of air hose varies only a few degrees from the temperature of the surrounding rock; in some instances the dry bulb temperature of the compressed air as it issued from the end of the air hose was higher than the rock temperature or the dry bulb temperature of the surrounding air."

May 1, 1921