Search Documents

By R. E. Lindstrom

Effective separation of rare-earth mixtures is obtained using hydrogen as a retaining ion at 200° F with ethylenediaminetetraacetic acid (EDTA) eluant. Results obtained in Bureau of Mines bench-scale apparatus and large columns with hydrogen as a retaining ion closely parallel those obtained with copper as a retaining ion. The use of hydrogen as a retaining ion permits EDTA and water, collected before rare-earth breakthrough, to be recovered in a form that allows the material to be recycled without extensive processing. With the exception of yttrium and dysprosium, separation of rare-earth mixtures is improved and throughput is increased by elevated temperatures. Separation with 1,2-diaminocyclohexanetetraacetic acid (DCTA) eluant increases markedly on increasing temperature from ambient to 250° F; however, on the basis of separation efficiency, DCTA does not compare favorably with EDTA.

Jan 1, 1962

Develop an improved downhole geophone system with enhanced signal/noise ratio for collecting cross-hole seismic data used in tomographic reconstructions. Background The Bureau of Mines is conducting research in the use of cross-hole seismic tomography for detecting and monitoring leach solution flow during in situ mining. This technique requires the use of a downhole seismic energy source in one borehole and a downhole wall-locking receiver (geophone) in another borehole separated from the first by the region to be investigated. Bureau research personnel chose a commercially available air gun for use as the downhole seismic energy source. Unfortunately, commercially available downhole wall-locking geophones that the Bureau tested were difficult to operate in the field, often unreliable and generally inadequate in terms of their signal/noise ratio. Therefore, research personnel began to experiment with an alternative down-hole geophone design that could be used to collect adequate data in a wide variety of borehole and cross-hole field situations. Approach An attractive alternative geophone design would be one that would incorporate a pneumatically operated wall-locking system. As an integral part of the Bureau's existing field system, a portable, high- pressure/low-volume air compressor would have sufficient capacity to operate the air gun as well as several small high-pressure pneumatic linear actuators. This approach was the simplest and most compatible with the research activities being conducted at the site.

Jan 1, 1991

By Edward D. Thimons

As U.S. mines go to greater depths, the high temperatures and humidities characteristic of such depths make it difficult to maintain a comfortable environment in working areas. Better techniques for cooling these deep working areas are needed. At the Homestake gold mine in South Dakota the Bureau of Mines has tested a water spray cooler inserted into the fresh air vent tube entering a warm stope. The cooler supplied more than 6 tons of refrigeration to the stope air, which dropped from an inlet temperature of 83° F dry bulb and 75° F wet bulb to 73.5° F dry bulb and 71.5° F wet bulb. These preliminary results show the water spray cooler to be a feasible concept. However, there is a need for substantial refinement and further testing, and work on the concept will be continued under contract to the Bureau.

Jan 1, 1979

By M. S. Seehra, R. S. Pandurangi

"A comparative study of the intensities of the IR modes in the pjlotoacoustic and. FrIR spectroscopy of amorphous and crystalline SiO2 particles is presented. It is observed that in photoacoustic spectroscopy of amorphous SiO2, IR modes of surface species are enhanced by over an order of magnitude compared to the bulk IR modes of SiO2. This effect, though not yet understood, may find applications in surface science.Since the publication of the Rosencwaig-Gersho theory of the photoacoustic effect in solids in 1976 [1], a great deal of attention has been paid to the development .of photoacoustic spectroscopy (PAS) into an analytical technique for condensed matter studies, especially when combined with the modern Fourier transform infrared (FTIR) spectrometer [2-8]. PAS has now been applied to a variety of experimental situations [2, 3] and it is particularly suitable for opaque powders and for cases where ~ample preparation (e.g. mixing with KBr as is usually done in FTIR spectroscopy) is not desirable. Another area of interest is the depth profiling feature of PAS, which is studied by varying the modulation frequency of the incident radiation [2-8]. The one-dimensional Rosencwaig-Gersho theory for non-porous samples has been extended to other cases [9-12]. Recently it has become known [11, 12] that for porous samples with porosity the IR modes are enhanced by a factor proportional toe. This enhancement is due to the pressure wave set up in the interstitial gas in the porous sample and this enhancement has been reported by a number of groups [12-14].In this Letter we report the observation of anomalously large enhancement of the PAS signal for certain surface IR modes on the surface of amorphous silica particles. This observation differs from the previous reports in that certain surface modes are enhanced by over an order of magnitude compared to the bulk IR modes. Although the reasons for this enhancement of the surface IR modes in PAS are not understood at present, this observation may open up new approaches to the study of surfaces. Results of these initial observations are given in this Letter. ·Experimental studies reported here were carried out on an FTIR spectrometer (Mattson Instruments, Model Cygnus 100) equipped with an MCT detector. The same instrument was used for PAS studies in conjunction with an MTEC (Model 100) PA cell. The sample cell and the spectrometer are continuously flushed with dry, CO2 free air obtained by the use of Balston Instruments Air Dryer Filter System (Model 75-60). Usually data were collected for 32 scans at 4 cm-I resolution, although both scan and resolution can be varied. For FTIR studies, samples were mixed with IR-grade KBr and pelletised. For PAS, no sample preparation is necessary and data are ratioed against dry carbon black [4, 5]."

Jan 1, 1989

By C. H. Herty

Intensive work on the deoxidation of steel with manganese-silicon alloys by the U. S. Bureau of Mines has shown that the use of those alloys, which may be produced from our domestic manganese ores, would decrease the ferromanganese requirements of a very large tone of our steel by from 60 to 30 per cent and in some cases by 100 per cent. The open-hearth heats made with these alloys have been of excellent quality. The tonnage of our ferro-grade ores which has been made available by the bureau's ore-dressing studies, combined with the ,products resulting from such processes as those developed by the bureau and by Bradley for Cuyuna ores, should easily fill our reduced ferromanganese requirements Then manganese-silicon alloys and ordinary spiegel are used in the way described in this report. There are no technical difficulties in the application of this practice, and any difficulties involved in its wide and immediate application would only be those arising from habituated ideas of the necessity of ferromangenese. General acceptance of this practice and development of the available sources of domestic ferro-grade material by already proven processes should make this country independent of foreign ores.

Jan 1, 1931

By J. G. Croeni

The high thermal-neutron cross section of gadolinium and the good mechanical and corrosion properties of titanium suggest that alloys of these two metals might be useful as control rod material. To aid in establishing the feasibility of this combination, the Federal Bureau of Mines investigated the titanium-gadolinium system. The results indicate that the system is composed of a single eutectic reaction and a peritectoid reaction involving the alpha-beta transformation of titanium. The eutectic isotherm extends from 1 to 99 pct, gadolinium at 1,240° C. The established eutectic composition is about 95 pct, gadolinium. The peritectoid reaction occurs at 885° C. and extends almost over the entire composition range. Hardness increases slightly with additions of gadolinium, and little change is obtained by heat treatment. Alloys containing less than 10 pct. gadolinium are amenable to extensive cold-working, but alloys having higher percentage of gadolinium content are only moderately cold-workable. All alloys can be hot-worked in iron sheathing at 750° C. Observation indicates that all compositions possess good machinability. Corrosion resistance to water at room temperature is apparently poor, especially in the gadolinium-rich alloys. INTRODUCTION A combination of the good mechanical and corrosion properties of titanium and the variety of thermal-neutron cross sections characteristic of the rare-earth metals suggests that alloys of these metals may be used for control rod materials. For this reason the Bureau of Mines proposed a study of the titanium-gadolinium alloy system, and the Atomic Energy Commission sponsored the investigation.

Jan 1, 1961

By A. L. Murray, P. A. Surgeon

The Spring Canyon Mine Rescue Association is a cooperative association supported jointly by five coal-mining companies located in Spring Canyon, Utah. The properties of mining companies the Carbon Fuel Co, Rains , Utah, the Liberty Coal Co. , Latuda, Utah, the Standard Coal Co. , Standardville , Utan, the Spring Canyon Coal Co. , Storrs , Utah, and the Peerless Coal Co. , Peerless , Utah about a mile apart and normally employ a total of 915 men , 733 underground 182 on the surface . and The Association was organized on July 5, 1921 , and Rudolph Clark, fomerly first - aid miner on U. S. Bureau of Mines Rescue Car 11 , was placed in charge. as manager . A board of directors made up of a representative from each of the cooperating companies (usually the mine superintendent ) is the governing body of the Association and the expenses are prorated on a basis of the production of each of the five mines . The Association maintains eight sets of Gibbs rescue apparatus and a motor truck fitted up as a combined rescue truck and ambulance . Additional apparatus are to be purchased . Standardville is the central camp in the canyon and has been made the headquarters of the Association . The apparatus are now kept and the truck housed in a small station, but plans have been prepared for a large station which will be built this summer . This new station will have a large apparatus room , a test chamber, a suitable room. for training, and a garage on the first floor, while above will be the living quarters of the manager . There is a good road through the canyon and the other camps are all within two and one -half miles of Standardville .

May 1, 1922

By Jr. Harty

Intensive work on the deoxidation of steel with manganese-silicon alloys by the U. S. Bureau of Mines has shown that the use of those alloys, which may be produced from our domestic manganese ores, would decrease the ferromanganese requirements of a very large tonnage of our steel by from 60 to 80 per cent and in some cases by 100 per cent. The open-hearth heats made with these alloys have been of excellent quality. The tonnage of our ferro-grade ores Which has been made available by the bureau's ore-dressing studies, combined with the products resulting from such processes as those developed by the bureau and by Bradley for Cuyuna ores, should easily fill our reduced ferromanganese requirements when manganese-silicon alloys and ordinary Spiegel are used in the way described in this report. There are no technical difficulties in the application of this practice, and any difficulties involved in its wide and immediate application would only be those arising from habituated ideas of the necessity of ferromanganese. General acceptance of this practice and development of the available sources of domestic ferro-grade material by already proven processes should make this country independent of foreign ores. This paper resents the results of work done under a cooperative agreement between the Pittsburgh Experiment Station of the United States Bureau of Mines and the Carnegie Institute of Technology, the Metallurgical Advisory Board, and the University of Pittsburgh, Pittsburgh, Pa.; between the Mississippi Valley Experiment Station of the United States Bureau of Mines and the Missouri School of Mines and Metallurgy, Rolla, Mo.; between the North Central Experiment Station of the United States Bureau of Mines and the University of Minnesota, Minneapolis, Minn.; and between the Rare and Precious Metals Experiment Station of the United States Bureau of Mines and the University of Nevada, Reno, Nev.

Jan 1, 1931

By A. F. Colombo

The differences in starch demands that occur between ore types subjected to the anionic flotation of calcium-activated gangue and the range of residual starch contents expected to give the best metallurgical response were evaluated on a batch and pilot plant basis. A phenol-sulfuric acid procedure was used to determine the residual starch contents in the iron ore slurries. Three pilot plant campaigns on samples from a group of orebodies located on the Marquette Range, Michigan, showed that in the rougher flotation pulp, a residual carbohydrate range of 25 to 100 ppm, which is equivalent to a 0.5 lb/short ton spread, yielded optimum results. Concentrates assaying at least 65 percent Fe and less than 6.0 percent Si02 and containing more than 80 per-cent of the recoverable iron were obtained. Both batch and continuous research indicated that starch adsorption is calcium modulated and relatively unaffected by the fatty acid additions employed. Residual starch level is not a critical control factor, but the addition must be adjusted to about 25 to 50 ppm residual starch and kept in this range for most effective utilization of the added tapioca flour.

Jan 1, 1972

By Lester G. Morrell

UPTREND in value of mineral production in the Commonwealth of Australia continued in 1963, again pacing the country's general economic growth rate. Increases occurred in output of most raw and processed mineral products, including bauxite, copper, iron ore, pig iron, steel, lead, zinc, cement, gypsum, pyrite, coal, and refined petroleum products. Although the economy of Australia has been traditionally based on wool and agricultural products, in recent years the country has become highly industrialized. Nearly one-third of the 3.6 million total civilian labor force is engaged in manufacturing. Employment in mines and quarries occupies 1.4 percent of the national labor force.

Jan 1, 1964

A complete list of permissible mining equipment, rescue apparatus and gas masks tested. Prior to Jan. 1, 1929, w s published in Bureau of mines Information Circular 60972. The present list includes practically all equipment tested and. approved by the Bureau, up to and including July 1, 1929. It covers electric air compressors, coal drills, mining machines, loading machines, conveyors, mine pumps, room hoists,, mine telephones, rock-dusting machines, switches, electric cap lamps, flame safety lamps, electric hand and trip lamps, flash lamps, methane indicators and detectors, blasting units, storage battery locomotives, tandem locomotives, power trucks, concrete mixers, self-contained oxygen breathing apparatus and gas masks. The system under which these devices were tested permits the manufacturer, after his equipment has passed certain tests prescribed by the Bureau of Mines, to mark his equipment with a seal showing hat it has been "approved" by the Bureau. These tests are designs to insure that the equipment has the minimum requirements for safety in use. The only object of the Bureau in making such tests and publishing lists of permissible equipment is to safeguard the lives of workers and to help lessen the hazards of mining.

Jan 1, 1929

By J. C. Franklin

The Spokane Mining Research Center of the Federal Bureau of Mines is placing major emphasis on chemical stabilization as part of the ground support program. Development of polymeric material suitable for bonding rock fractures around the mine opening is one phase of the program. Some of the problems that must be considered are viscosity, applicability, adhesion, cure times, strength, toxicity, and flammability. Epoxies and polyesters were investigated, but shrinkage in polyesters caused redirected effort toward epoxies. Test results with the latter showed that bonded fractures in mine-roof strata were stronger than the virgin rock. Further tests showed that polymeric materials have good potential for bonding, and in conjunction with polymer roof bolts, are expected to result in an economic and useful new support concept.

Jan 1, 1974

By F. P. Haver

The Bureau of Mines developed a process to extract about 90 percent of the sulfur from molybdenite flotation concentrate by compacting the concentrate with one-quarter of its weight of aluminum powder, heating it at 800° C for 30 minutes, and then allowing the product to react with water. This thermite reduction yields an impure molybdenum alloy plus aluminum sulfide. The latter readily hydrolyzes, to yield pure hydrogen sulfide which can be converted to elemental sulfur by the Claus process. At least 95 percent of the molybdenum can be subsequently recovered as 99.95-percent-pure molybdic oxide.

Jan 1, 1968

By Steven R. Davis

Dear Interested Party: Subject: Notice of Intent to Solicit Outside Opinions Regarding Amendments to the Rules Concerning the Leasing of State Owned Lands for the Mining of Metallic Minerals The Department of Natural Resources, Division of Minerals, is seeking outside opinions concerning the leasing of state owned lands far the mining of metallic minerals. Enclosed for your information in a copy of the Notice of Intent to Solicit Outside Opinions Regarding Amendments to the Rules Concerning the Leasing of State Owned Lands for the Mining of Metallic Minerals.

Jan 1, 1994

By Robert T. Beckman

The results of a preliminary investigation of compressive strength versus length-diameter (L/D) ratios of potash specimens and the statistical treatment of the data are summarized in this report. The purpose of the study was to evaluate a laboratory method for obtaining estimates of the strength of potash pillars during robbing operations. The specific objectives of this preliminary investigation were to test the method and the reliability (confidence limits) of the data, and to determine the number of additional specimens necessary for given confidence limits. The specimens were taken from three sites at two mines in New Mexico. The statistical analyses included the determination of the confidence limits for the data and the number of additional specimens necessary to obtain confidence limits of ±500 and 100 psi. The testing method was found acceptable, and estimates of the comprehensive strength, within 1500 psi, could be obtained by testing about 110 additional specimens from the three sites. The compressive strength of the specimens tested fits an empirical equation of the type

Dec 1, 1963

By A. G. Galaitsis

The two volumes of this report summarize the noise control work performed by BBN on a rail personnel carrier operated in coal mines. Volume I of the report - submitted November 1977 - describes the aboveground work performed to identify the noise sources, design, fabricate, and install the treatments, and evaluate the treatments through noise and vibration tests. The current volume (II)-describes the underground work conducted by BBN to determine the deterioration, if any, of the treatments when the vehicle is operated normally in a mine. There were no significant changes in the acoustical performance or mechanical integrity of the treatments at the end of a three-month period.

Jan 1, 1980

By C. C. Merrill

Studies were made to determine the amenability of yttrium to fused-salt electrorefining in a controlled atmosphere. Tests were conducted in a LiCl- YCl3 electrolyte system at 710° C. The major variables studied were the YCl3 content of the electrolyte, from l.7 to 13.4 mol percent, and the initial cathode current density, from 410 to 1,630 amperes per square foot. Vacuum distillation was employed to remove salt from the deposited metal. Metallic impurities, except for lithium, could be reduced to near or below their lower analytical limits, ranging from 10 ppm for Cu to 300 ppm for Ta; reduction of oxygen content, however, was accomplished only in metal produced from electrolytes with 5.4 mol percent YCl3 or less. Initial cathode current density had little effect on the purity of the product.

Jan 1, 1967

Consumption and intensity of use trends for 12 metals, by industrial end use, were estimated for 1972 through 1982 by the Bureau of Mines and U.S. Department of Commerce. The trends were then forecast through 1993 using standard statistical methods. The intensity of use measure selected is the quantity of metal consumed per constant dollar output of a specific industrial sector. The metals studied were aluminum, chromium, cobalt, copper, lead, manganese, nickel, the platinum-group metals, tin, titanium, tungsten, and zinc. Average annual growth rates for the following 4 of the 12 metals increased from 1972 to 1982 as follows: aluminum, 1.00%; platinum-group metals (consisting of platinum, palladium, and iridium), 8.83%; titanium, 7.82%; and tungsten, 6.09%. Consumption for the remaining eight metals decreased at average annual rates ranging from 0.58% (copper) to 5.37% (manganese).

Jan 1, 1986

By James W. Ballard, H. H. Schrenk

"The X-ray method of quantitative determination is advantageous because it permits determination of compounds rather -than ions or elements; for example, the direct determination of quartz in silicates,4/,5/,6/ The method also takes into account the finest particles of a sample, which may be lost in wet chemical methods because of solubility or in petrographic methods because of limitation of the microscope. The sample is usually reduced to a powder and is easily prepared,7/ only a few milligrams of material being necessary. The sample and its chemical composition are not destroyed and may be used for further analysis by X-ray diffraction or by other methods.This paper presents in detail some of the more essential problems that arise in the application of X-ray diffraction to quantitative chemical analysis, Photometric measurements are discussed in connection with line intensities and the choice of X-ray film. The internal standard method, successfully used in spectrographic analysis, is applied.Copper K-alpha X-rays from a demountable research-type X-ray tube were used with a camera of 20 centimeters radius with a cast-lead-slit collimating system. A combination of a tilted wedge and a lead-slit collimating system permitted irradiation of a large amount of sample with X-rays. This tended to minimize errors due to possible inhonogeneity of the sample, to decrease the time of exposure, and to keep the lines on the X-ray film to a minimum width. There was sufficient dispersion of the lines for satisfactory analysis of most samples. Power was furnished the tube by a. source of constant high potential consisting of a synchronous motor generator furnishing 500-cycle power to a 100-kv. transformer, rectifying valves, and a condenser filter circuit. The X-ray tube was operated as a gas-type tube at 35 kv, and 20 ma,, the exposure times varying from 1 to 2 hours. The constant output of X-rays from the tube, indicated bar an exposure meter built for the purpose, was satisfactory.The recording microphotometer8/has been described. It was found preferable to a nonrecording instrument for measuring blackening of lines above a background on X-ray films. This background, which usually occurs, is sometimes complicated by numerous peaks from lines of complex diffraction patterns. is microphotometer record of the pattern, therefore, facilitates the location of the background 'and the measurement of the heights of the peaks and thus contributes to the accuracy of a determination."

Jun 1, 1946

A spectrographic procedure applicable to the semiquantitative determination of 29 elements in tungsten is presented. The method is designed to give estimates of impurity concentrations up to 500 p.p.m. Limits of detectability range from 0.3 p.p.m. for the more sensitive elements to 100 p.p.m. for the less sensitive ones. Tungsten metal samples varying in particle size from minus 300-to 30-mesh are excited in the presence of 5 percent germanium with a direct current arc. Germanium acts to stabilize the arc, minimizes the volatilization of tungsten, and serves as an efficient carrier to sweep impurities from the tungsten into the excitation zone. Curves are presented that show the volatilization behavior of germanium, tungsten, and impurities in tungsten at different concentration levels. Data obtained were used as guides in establishing the method of analysis. In the absence of established reliable analytical procedures for determining many impurities in tungsten in the parts per million concentration range, the spectrographic method described here should prove to be helpful in evaluating high-purity tungsten.

Jan 1, 1961