Search Documents

By H. Kenneth Sacks

The Bureau of Mines has developed hardware for electromagnetic (EM) detection and location of miners trapped in underground coal mines. This report describes a technique for using the developed equipment for locating uncased boreholes underground. Results of several field and laboratory experiments are described.

Jan 1, 1978

By Walter C. Lorenz

Samples of materials containing pyrite from various coal mines and coalbeds were studied to compare their compositions and oxidizing characteristics. Pyrite was the only form of iron sulfide identified, but X-ray diffraction, emission spectrography, and microscopic analyses revealed similar suites of minerals and trace elements. The pyrite occurred usually in spherical clusters of very small crystals. The oxidation of pyrite in solutions of PeSO4 and Fe2(SO4)3 and in the presence of an iron oxidizing bacterium Ferrobacillus ferrooxidans, was studied through a manometric technique. FeS04 or Fe2(SO4)3 solutions had no appreciable influence on pyrite oxidation under the test conditions, The bacterium acted as a catalyst, greatly increasing the oxidation rates; however, in three samples that also contained calcites, bacterial oxidation was greatly reduced. The oxidation rates also increased approximately as the percentage of pyrite in the samples increased. For the series of samples studied, there was no definite correlation of the results with the location of the various mines nor with the acidity of alkalinity of the mine drainage.

Jan 1, 1963

By Maust. E. J., W. R. Crane

"IntroductionIn the study of mine drainage in the red iron ore mines of the Birmingham district of Alabama, an extensive series of measurements were made in order to determine the drainage from the area overlying and adjacent to the mines. Gaging rods were generally used in measuring streams, and weirs in ditches and sometimes as a check on rod work. These tests in turn were checked by current meter tests. In all, 725 separate stream gagings and 97 weir measurements were made. Certain relationships were worked out, particularly between rod and weir tests, which permitted obtaining results that are much more accurate 'under the existing conditions, than any available formula would give. The large number of weir measurements and the period covered by the tests made it impracticable to construct a weir for each observation so portable, adjustable weirs were built. The methods used are described here for the benefit of those interested in measurement of streams in connection with a study of mine drainage or otherwise. The Drainage AreaThe area draining the mining district lies between the crest of Red Mountain and Little Shades Creek, and for convenience was divided into sub-districts adjacent to certain groups of mines. Gaging stations were established on Little Shades Creek at the upper and lower boundaries of each sub-district, also at points on the tributaries near their junction with the creek. The difference between the volumes of water flowing in Little Shades Creek as it entered and left the sub-districts represents the flow from the tributaries on both sides of the creek. Since the flow coming from the sub-districts was measured direct, the inflow from the tributaries on the opposite side of the creek can be computed from the three volumes determined."

Oct 1, 1926

By Charles T. Chislaghi

An economical, remotely operated (automated), temporary roof support (ATRS) has been developed by the Bureau of Mines for use on a single, fixed-head roof-bolting machine (squirmer) that operates in low coal seams (less than 42 in thick). The ATRS eliminates the need for squirmer operators and helpers to go under unsupported roof to set or remove temporary support prior to or during the roof-bolting cycle--a task that annually accounts for approximately 20 pct of all roof fall fatalities. The ATRS can be adapted to any squirmer used in the U.S. low coal fields. A prototype ATRS was field-tested at Imperial Colliery Co.?s Mine No. 20 in Eskdale, W. Va. The Mine No. 20 amended roof- control plan, which requires the use of the Bureau?s ATRS as temporary support during face bolting, has been approved by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor.

Jan 1, 1982

Flexible hoses with rated working pressures up to 40,000 psi are used when high-pressure water jets are employed to cut rock or improve the performance of mining machines. Hose failures at such high pressures can result in serious injuries to workers. The Bureau of Mines used fatigue and burst tests to investigate the failure modes of high-pressure hoses at their rated working and burst pressures. Fatigue failure, at rated working pressures, occurred when the inner liner of the high-pressure hose broke, allowing water to seep through the wire wrapping, although the reinforcement wires did not break. At the burst pressure, all hoses failed catastrophically when the reinforcement wires broke. Low-pressure hoses placed over the high- pressure hoses for safety failed to contain water released by catastrophic failure.

Jan 1, 1987

By George S. Rice

"The successful use of the gas mask by the American Army it France in combatting the poisonous gases of German .shells caused many Army men to feel that the as masks were proof against any kind of gas which might be encountered. The result has been that from time to time there have been reported in the press, deaths of former army men through using their masks to enter various kinds of gases such as illuminating gas, gasoline vapor, and the gaseous atmospheres produced by mine fire. Such a case has just been reported from a mine, in Copperopolis, California, where a former Army man lost his life in descending a mine shaft filled with the fumes of a mine fire. Another man who, in attempting to rescue him, merely used a dust respirator, lost his life also.While the American type of the Army gas mask was developed by the Bureau of Mines for the War Department, and since the war a section of the Bureau's in¬vestigative force has been developing industrial gas masks for certain specificgases, the Bureau has repeatedly called to the attention of the public the fact that such masks have serious limitations and in no case should a gas mask be used in underground workings for the reason that there may be an insufficient amount of oxygen to breathe, (and the gas mask does not supply oxygen) or there may be present carbon monoxide, which the Army mask will not remove, and there always is some carbon monoxide produced by a mine fire or by a coal-mine explosion, or by a blast of dynamite or other explosive.It is true that the Bureau has been developing a mask which may take care of a small percentage of carbon monoxide, that is, one per cent and under, but in mine fires and after explosions, there may be, and frequently is, a much larger percentage of carbon monoxide in the mine atmosphere. Masks such as these, for small percentages of carbon monoxide and associated gases are for use in connection with industrial surface plants, as for example, on the top of a blast furnace or around gas producers in the open air."

Oct 1, 1920

By John Nagy

Limited experiments in the laboratory with specimens of mine rock from a Virginia bituminous coal mine indicate that natural gas-air mixtures can be ignited by sparks generated by rubbing friction of sandstone against sand-stone, shale against sandstone, sandstone against (roof-bolt) steel, and shale against steel. Such sparks, generated during a roof fall, may have initiated a recent gas explosion in this Virginia mine, although this cannot be stated with certainty. No ignitions of gas were produced by sparks or heat generated by impact friction between mine rocks or steel, during tension breaks of roof bolts, or by pull tests of roof bolts through their washers and roof plate. However, this negative result of limited experiments does not preclude the possibility of gas being ignited by these conditions.

Jan 1, 1960

By Steven M. Shope

The Bureau of Mines electromagnetic trapped miner location and communications system requires a thorough understanding of through-the-earth electromagnetic wave propagation. An earth model incorporating a magnetic dipole buried in a three-layered earth has been developed. The dipole source is located in the second subsurface layer. By application of proper limiting values, the three-layered model is reduced to two different two-layered models and eventually to the homogeneous half-space model. The solutions are in the form of infinite integrals. A numerical analysis was carried out and a computer program written to evaluate the surface magnetic fields. Numerical values for the magnet- ic field at the point above the source are presented in a variety of models.

Jan 1, 1982

Compare the dust control efficiency and bit life of surface coal mine drills using standard water injection and water injection with water separation. Approach A research study was conducted to determine if a water separation technique affects wet suppression dust control. Dust control efficiency and bit life of surface coal mine drills were compared during tests using both standard water injection (wet drill bit cutting) and water injection with water separation (dry drill bit cutting). Background Surface coal mine blast hole drills typically generate a substantial amount of dust during the drilling cycle. One method used to control this dust is the injection of water into the bailing air. This is known as wet suppression.

Jan 1, 1988

By Lloyd A. Morley, Alan M. Christman

Presented below is a review of how the objectives, as outlined in the statement of the problem, were achieved. 1. Methods of evaluating the performance of grounding systems must be described. These methods are the subject of Chapter III. 2. Field trips to operating mines should be undertaken, and a cri¬tique of their grounding systems made upon the basis of obser¬vation and the application of the above techniques. An analysis of field trip data, along with practical recommendations, is in¬cluded in Chapter IV, while a complete review of all field trips is given in Appendix I. 3. Because of their thoroughness, present coal mine regulations should be evaluated, and their applicability to open-pit environ¬ments appraised. This has been done in consultation with governmental agency, manufacturing, operating mine, and consult¬ing engineers. As stated in Chapter IV, insight gained through field observations has served to amplify and extend the base of knowledge from which the recommendations were made. 4. The results of these investigations should lead to suggested Federal standards. Such recommendations comprise Appendix II. In addition, several important factors, which are discussed in Chapter IV, were brought to light as a direct result of the field research. 5. Seasonal variations in the earth resistance of ground mats, as illustrated by Table 12, reinforce the need for periodic

Jan 1, 1976

By A. B. Hooker

Investigations at the Pittsburgh Experiment Station of the Bureau of Mines have shown that satisfactory operation of a flame safety lamp depends not only upon proper design and assembly of the lamp but also upon the kind

Jan 1, 1945

By R. E. Stiles

The modified perchloric--EDTA method devised by the Bureau of Mines for the determination of copper in high-grade samples gives results that are more precise and more accurate than those from the classical sulfuric-iodometric method. Although the perchloric--EDTA method is more costly than the conventional method, the savings in time alone largely offsets this difference. Specifically, the modifications wade in the more conventional procedure comprise (1) use of perchloric acid instead of sulfuric acid for dissolution of copper minerals, (2) precipitation of copper as copper sulfide from dilute perchloric acid solution, (3) wet oxidation and dissolution of the precipitated copper sulfide, (4) use of larger amounts of indicator than those employed in the Schwarzenbach method of titrating low-tenor copper solutions with disodium ethylenedinitri10-tetraacetate and murexide indicator, and (5) use of refrigeration to partially stabilize aqueous solutions of the indicator.

Jan 1, 1966

By A. W. Ambrose

"Records of individual wells form the basis for the successful operation of any company engaged in the production of petroleum. The expense attached to the compilation of records is negligible in comparison with the benefits resulting from their use. There a company has not a complete system of records, immediate attention should be given to the preparation of forms upon which to collect data, and, to the collection of data for these forms. The records needed vary with each district, but for each field a set should be adopted that will best meet the needs of each property. Practically all operators, and particularly all successful operators, agree on the necessity of good records, shopping what the wells have done, are doing, and may be expected to do in the future. Any operator realizes the value of records of sales of oil and should place almost equal emphasis on the records of well logs and histories showing the east and present performances of wells. Indeed, trustworthy records are absolutely necessary for the proper operation of any oil or gas property.Complete records should be kept on each well from the time the location and elevation are determined until the well is abandoned, and the engineer should review old records often enough to be familiar with the past performance of the various wells and with the conditions that affect production. Some of the forms that may be prepared are:--"

Mar 1, 1920

To improve electrical safety and lengthen light bulb life on trolley haulageways. Approach A resistor inserted in series with each pair of light bulbs, decreases the voltage applied to the bulbs and eliminates heavy arcing when voltages rise. How It Works Under certain conditions, incandescent light bulbs connected directly to a 300-volt d-c trolley wire can be a hazard, particularly during weekends when electrical equipment is nut in use. When little electrical power is being used, the voltage (on the trolley lines and at the substation) can rise to a value which will destroy the bulb filament, cause arcing, and damage the bulb holder. In one coal mine where light bulbs in certain locations fre¬quently failed, the problem was overcome by inserting a 100-ohm, 50-watt resistor in series with each pair of light bulbs. The light bulbs are rated at 300-volts and 100-watts. Figure 1 shows the light bulbs and resistor circuit. This resistance was added in order to reduce the current through a short circuited bulb holder, from several hundred amperes to a much safer value of 3 amperes. However, the resistor in series with each pair of light bulbs, also reduces the voltage across the lighted bulbs to approximately 240 volts during periods when the trolley line voltage is up to 300 volts. With this arrangement, no light bulb failures occurred over a 6-month period. The resulting light reduction has not been objectionable.

Jan 1, 1976

By A. Z. Dimitroff

An improvised rock-dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jan 1, 1965

By L. C. Marchant

Results of detailed analyses of four cores from the Threemile Canyon area in the P. R. Spring tar sand deposit in Utah are reported by the Bureau of Mines. The cores were obtained by the Utah Geological and Mineralogical Sur-vey as part of a l7-corehole evaluation program in the P. R. Spring, Hill Creek, and Rim Rock tar sand deposits. Average properties of the oil zone in the Threemile Canyon area as deter-mined from these cores are as follows: Oil saturation, 67.4 pet of pore volume; porosity, 29.2 pct; permeability before oil extraction, 133 millidarcies; and permeability after oil extraction, 2,855 millidarcies. Average net thickness of the oil zone is 23.8 ft and average depth to the top of the oil zone is 189 ft.

Jan 1, 1974

The question of earth models has repeatedly arisen in our work. An accurate representation of the seismic properties is required for three reasons: 1.To be able to determine from a set of received arrival times, the location of a seismic source in the earth, and secondly the degree of accuracy required in the model used for calculating source location from the set of arrival time differences. 2. To be able to determine the expected arrival times at an array of geophones produced in response to a hypothetical source in the earth. 3. To be able to estimate received signal strengths more accurately. The work reported here on earth models is based on information from sever- al consultants and from others who expressed an interest in the problem and supplied information to us. II. COAL MINE GEOLOGY On one of our earlier assignments for the Bureau of Mines, Earth Science Research Inc. of Cambridge, Massachusetts prepared for us a short description of the lithology to be expected at coal mine sites. This description follows, together with the ranges of compressional seismic velocities (Figure I*) associated with typical materials comprising the layered structure of a coal mine area. Coal is primarily associated with fresh water sediments including sandstones, shales, and clays, and occasionally may be metamorphased to varying degrees. In the Appalachian Basin the coal beds occur within cyclical sequences of non-marine shales, sands tones, conglomerates, limes tones, and clays. The beds range in thickness from a few inches to 60 feet, averaging between 2 feet and 10 feet. They have generally broad areal extent, occasionally up to 5,000 square miles, and have an overall tabular or lens-like shape. Within a particular lens, local changes in thickness are normal.

Jan 1, 1974

By Fred N. Kissell

Experimental work by the Bureau of Mines indicates that when a coalbed is degassed by boreholes, the flow of methane may actually increase with time. This phenomenon appears to be the result of a relative-permeability effect; that is, the coalbed permeability to the gas increases sharply with decreasing water saturation. This report reviews the background of experimental evidence indicating a relative-permeability effect, and presents the results of a computer simulation of two-phase flow in coal.

Jan 1, 1975

By M. J. Ankeny

All bituminous-coal mines, by the nature of their product and inherent gassy tendencies, are subject to explosions or mine fires. The evolution from large, hand-loading sections employing numerous men and containing open-type equipment, lights, and nonpermissible explosives to small, concentrated mechanical sections with but few well-supervised men utilizing modern preventive equipment has not altered this premise. Mine catastrophes such as Centralia and New Orient No. 2, as well as recent disasters of less magnitude, have refuted the trend of thinking that modern equipment, will prevent or localize explosions and prevent widespread or loss of life.

Jan 1, 1952

By C. B. Manula, R. L. Sanford, R. A. Rivell

A - Contains the coordinate pair information for deriving the co¬efficients of the 3rd degree polynomial which approximates the loading station equation. C(N) - Coefficients for third degree approximating polynomial. I - General DO LOOP variable. K - Position in BRANCH of next character. L - Format specification in DEFINE FILE statement. X - Uniform displacement for random uniform number. Y - Load increment At. AO-A3 - Coefficients of approximating polynomial for loading station equation. GR - Grade direction, or grade resistance. IQ - Counts quadruples of distance grade speed and end of route for determining total distance. IT - Intersection counter in XXXDEF. Il - Station number trip is leaving. Jl - Station number for trip destination. J2-J8 - Motor assignments and functions for given trip. KK - Location of starting grade and distance in DISTGR KK - Position of decimal point in real number. KZ - DO LOOP variable for motor assignment check. LL - Location of ending grade and distance in DISTGR. Ll - Position in IECB of station satisfied. L3 - Next available position for IECB sort. MM - Flag for printing the failure of sanding to overcome slippage. NN - Trip destination in MOTSER RR - Rolling Resistance. XK - Station level or type.

Jan 1, 1974