Search Documents

By Suresh K. Bhatt, Dennis R. Dolinar

The roof bolt system of a mine, if properly selected and installed, can allow for better roof control and reduce the potential for roof falls. Because of this potential to reduce roof falls and improve ground control conditions, the National Institute for Occupational Safety and Health (NIOSH) has an interest in the types of roof bolts that are used by the coal industry. Further, NIOSH has conducted research into how various support parameters can affect the number of roof falls that occur, including support type. Today, the five main types of roof bolts installed in U.S. coal mines are mechanical anchor bolts, point-anchor or resin-assisted mechanical anchor bolts, torque-tension bolts, combination bolts, and fully grouted resin rebar. This paper describes each support in detail. Because of the importance of resin in the functioning of the majority of bolts installed, resin grouts are also discussed. Further, trends in the types of roof bolts used are reviewed. Over the last 10 years, the significant trend has been the large reduction in the relative number of mechanical anchor bolts that are installed. These bolts have been replaced mainly by the resin-grouted rebar system. Data are also presented to show the impact of these changes in bolting on the number of roof falls.

Jan 10, 2000

By Fred Leighton

The Bureau of Mines monitored a rock-burst-prone pillar in a metallic ore vein, up to and through failure, to measure its reactions to increasing loads, as it was mined. Three parameters were monitored: the stress changes at chosen points within the pillar, the displacement characteristics of the drift above the pillar, and the micro-seismic activity in and around the pillar. In descending order of effectiveness, the microseismic technique, vibrating wire stress measurements, and displacement measurements reflected the pillar reactions, and all showed good correlation to one another. A major rock burst in the pillar, which destroyed about 100 feet of drift above the pillar, occurred at the end of this study. This burst was preceded by a large anomaly in the microseismic activity in the failure area.

Jan 1, 1982

By M. A. Trevits, S. W. Lambert

In this Bureau of Mines investigation, production was monitored for 1 year at over 30 coalbed gas-drainage boreholes located in Alabama, Pennsylvania, and West Virginia. Results indicate that the quality of data gathered from such wells can be improved greatly if potential problems are anticipated and prevented in the early stages of well production. Major water-monitoring problems include solids buildup, freezing, the presence of gas in surface waterlines, and improper pumping interval settings. Such problems may be avoided by incorporating in the original well design waterline filters, sand screens, separator tanks, and systems to automatically control pumping intervals. Problems related to measurement of coalbed gas flow include large quantities of water vapor contained in the gas, especially during winter months; freezing and subsequent obstruction of flow; sudden, uncontrolled release of gas pressure; and solids buildup in metering equipment. The installation of commercially available items, such as filters, separators, and insulation, and the thoughtful application of a basic knowledge of coalbed gas reservoir characteristics will prevent most production-monitoring problems.

Jan 1, 1978

By F. W. Penn

An aircraft auxiliary power unit (APU) was used as an exhaust source for evaluation and refinement of sampling and analytical procedures for gas turbine engines. The unit was also used to determine the emission characteristics of APU's in service and to study the effect of fuel composition and combustor design on exhaust emissions. Carbon monoxide, carbon dioxide, oxides of nitrogen, hydrocarbons, aldehydes, particulate loading, and odor were measured at engine operating modes representing the duty cycle encountered in airline operation. Analyses showed good repeatability, and adequate sensitivity was attained in these experiments. Smoke opacity measurements were not taken owing to the lack of a high-sensitivity smokemeter. Results showed that the minimum emission levels occurred with the standard combustor and Jet A fuel. Emission rates were highly dependent on test mode, but emission patterns as a function of test mode were similar for all fuels and combustors tested. A comparison of three identical design production combustors showed a variation in average emission rates of less than 5 pct.

Jan 1, 1973

By Kent Volkmer, Mark Sanders, Gregory Krohn, Tyler Blake, Daniel Wick, Barry Beith

This report describes a study designed to evaluate a proposed modification in the cap lamp battery cord intented to reduce the incidence of snagging and catching of the cord. A three phase evaluation as performed comparing a prototype with the standard, currently available cord. First, a "pull test" equipment was run. The second evaluation was a body conformity study. The third evaluation involved subjects performing common tasks in a low seam coal mine simulator. The results of these evaluations clearly demonstrated significant safety advantages of incorporating coiled cord into the design of the cap cord. The coil cord presented less of a snagging hazard, allowed the wearer more time to respond to a snag, and transmitted lower levels of force to the helmet when snagged. The research team recommended that cap lamp cords be commercially developed which incorporate coiled cord at the battery and helmet.

Jan 1, 1980

By S. J. Anderson

The Bureau of Mines compared three methods of rock cutting using drag cutters under controlled laboratory conditions. The methods tested were the conventional drag cutting method used on continuous miners, the kerf-core method used on some boring machines, and an experimental method called ripper cutting. All three methods were tested in blocks of Indiana and Kasota limestone. The results of this testing showed ripper cutting to be 30 to 40 pct more energy efficient than both the conventional and the kerf-core methods in Kasota limestone and 35 pct more efficient than the kerf-core method in Indiana limestone. The conventional method was, however, 9 pct more energy efficient than the ripper method in Indiana limestone. These results are considered promising, and more tests are planned with the ripper cutting system.

Jan 1, 1987

By C. M. K. Boldt

This U.S. Bureau of Mines report presents a study of three typical tailings samples as potential cemented backfill in underground mines. The testing series was unique in that the pulp densities of the samples were all above 75 pct solids. Test results included dry density; slump; percent settling after 28 days of curing; tensile strength after 28, 120, and 180 days of curing; and unconfined compressive strengths after 7, 28, 120, and 180 days of curing. The physical properties of the various test mixtures were further analyzed using linear and nonlinear statistical methods to produce correlations and mathematical equations. Physical properties were used to determine the influence of mix additives and as input for numerical modeling studies of backfill. The mathematical relations were used as a predictive tool in determining the suitability of various materials as backfill.

Jan 1, 1989

By George S. Rice

"Soon after the armistice, an investigation was conducted by the writer on the use of liquid oxygen for explosive purposes in Germany, so far as the conditions of such investigation wore permitted at the time. The results of this inquiry were published in Technical Paper 243, entitled ""Development of Liquid Oxygen Explosives during the War.""Recently, through the courtesy of Dr. C. L. Parsons, former chief chemist of the Bureau, who was visiting Germany, and Mr. Chester L. Benson, of the American Expeditionary Forces in Germany, data was obtained from the Deutsche Oxhydric A. G., Surth near Cologne, (one of the principal manufacturers of liquid oxygen installation) concerning the number of plants which bad been installed in Germany during the period following the armistice. An analysis of the figures obtained shows the following installations in different kinds of mining operations:"

Sep 1, 1920

By C. E. Jordan

The Bureau of Mines conducted tests on seven samples of Florida phosphate operations.slimes to develop a method to recover phosphate presently being discarded because of its small grain size. A system of hydrocyclones and hydroseparators was used to recover up to 96 pct of the plus 400-mesh material from the slimes. This plus 400-mesh material was subjected to fatty acid flotation, and concentrates containing up to 33.4 pct P205 were produced. As much as 88 pct of the phosphate (P205) was recovered from the plus 400-mesh material, and up to 29.6 pct was recovered from the total slimes.

Jan 1, 1982

Develop a cost-effective diesel aerosol sampler that can be used by industry and regulatory agencies to determine the diesel exhaust aerosol concentration in mine atmospheres. The sampler must be easy to use, wearable by mine personnel, compatible with current personal sampling protocols, and inexpensive. Approach The University of Minnesota (University) and the U.S. Bureau of Mines (USBM) have developed and tested a prototype diesel exhaust aerosol sampler. The sampler, however, was complicated and expensive to fabricate. Consequently, the USBM redesigned the sampler to simplify both manufacturing and use, and the sampler was evaluated to ensure equivalency with the prototype. Background The National Institute for Occupational Safety and Health (NIOSH) has recommended that "whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration." In addition, the U.S. Mina Safety and Health Administration (MSHA) has been directed by an advisory committee to establish a diesel exhaust aerosol standard and regulations to minimize exposure to diesel pollutants in underground coal mines.

Jan 1, 1992

By A. A. Giardini

This report represents the results of a literature study on boron nitride and related substances. The purpose of the study was to find Information that might be of value for production of a new, hard modification of boron nitride preferably in single crystal form. The report consists of a review of the major developments in boron nitride research, a discussion of the results, tabulations of physical and chemical properties;, conclusions drawn from the study, and a bibliography.

Jan 1, 1953

By Daniel N. Tallman

To provide technology for achieving more efficient water filtration systems for the mineral industry, the Bureau of Mines performed demon-stration filtration tests at three iron ore mines and one steel mill. A comparison of equivalently sized magnesium oxide (MgO) and sand filters showed that MgO had a higher capacity and could operate at higher fil-tration rates than sand. In demonstration tests when alum (AlK(S04)2) was the coagulant, suspended solids breakthrough occurred even though the pressure across the filter (head loss) was 7 psig or less. Under these circumstances, the MgO demonstrated 20 to 100 pct greater filtra-tion capacity, defined in terms of the volume of water filtered before breakthrough. When an organic floccu1ant was used at one location, head loss was the run-limiting factor; the filters essentially plugged with-out any solids breakthrough.

Jan 1, 1985

By D. E. Hirsch

The types of compounds present in aromatic concentrates derived from high-boiling petroleum distillates can be estimated from a gel permeation chromato-graphic (GPC) analysis by the use of tables developed from extensive GPC and mass-spectral analyses on fractions from four crude oils. For a fraction from the GPC analysis, the retention volume and the molecular weights (from mass spectrometer) suffice to indicate the types of compounds which predominate. The tables which show these qualitative analyses were developed through the use of pure compounds as well as the extensive analyses on Prudhoe Bay (Alaska), Gach Saran (Iran), Swan Hills (Canada), and Wilmington (California) crude oils. These tables provide a rapid method for determining which types of compounds are present in a GPC fraction before attempting to develop quantitative data.

Jan 1, 1974

By Thomas P. Mucho, Dennis Dolinar, Christopher Mark

During the 1990s, the former U.S. Bureau of Mines conducted a number of field studies in which the performance of different types of roof bolts were evaluated in different geologic environments. The studies used a standard suite of measurements, including multipoint extensometers, strain-gauged roof bolts, and roof bolt load cells. The sites were chosen to investigate the effect of a variety of parameters, including installed tension, bolt capacity, grout annulus, and horizontal stress orientation. Although not fully successful, the measurements provided valuable insights into each of these issues. They also showed that instrumentation and monitoring have important advantages over observational methods for comparing the performance of different roof bolting systems.

Jan 10, 2000

By P. Bhakta

The U.S. Bureau of Mines developed an alkaline oxidative pretreatment leaching procedure to increase the recovery of gold from arsenopyrite (FeAsS) ores. The best solution compositions for arsenopyrite dissolution were determined using cyclic voltammetry and chronocoulometry. Initial arsenopyrite dissolution occurred at -0.20 V versus standard hydrogen electrode (SHE) in a sodium hydroxide (Na0H) solution. Leaching of a high-grade arsenopyritic ore containing, in percent, 28.2 As, 25.3 Fe, 19.9 total S, and 1.0 Sb and, in troy ounces per short ton, 1.6 Au and 5.5 Ag resulted in >90 pct As extraction at 1000 C, 40 psig O2,4 h, and 2M NaOH solution in a 2-L autoclave. Cyanidation of the leach residues resulted in 90 to 93 pct Au and 60 to 80 pct Ag extractions, compared with only 5 and 15 pct, respectively, without the pretreatment. The procedure was further tested by leaching a low-grade gold ore and a bulk sulfide flotation concentrate prepared from it. Cyanidation of the leach residues resulted in 70 pct Au and 31 pct Ag extraction. The NaOH leachate was partially regenerated by precipitating the arsenate as calcium arsenate [Ca3As04)2] and the sulfate as barium sulfate (BaS04).

Jan 1, 1989

By D. R. Tesarik, F. M. Jones, J. B. Seymour

As part of safety and stability studies at three underground mines in the United States, researchers installed earth pressure cells and embedment strain gauges in cemented rockfill to measure stress and strain changes as mining progressed and the rockfill was loaded. Data from these instruments were used to calculate the in situ modulus of the rockfill for two of the mines. A three-dimensional numerical model of a cemented rockfill cap was validated with data from extensometers anchored in the mine roof and sill; this model was then used to estimate deformation modulus at the third mine because the earth pressure cells and embedment strain gauges recorded negligible changes. Rockfill binder used at these mines ranged from 4 to 8 per cent of the dry components by weight, the water-to-cement ratio was from 0.42 to1.0, and the largest aggregate size in the three mixes ranged from 5 to12 cm (2 to 4.7 in). The range of the calculated in situ deformation modulus values was large, but as expected, it was bracketed by modulus values for cemented tailings and roller-compacted concrete with similar cement contents and water-to-cement ratios. Dans le cadre d’études sur la sécurité et la stabilité de trois mines souterraines situées aux États-Unis, les chercheurs ont installé des palpeurs de pression des terres et des extensomètres d’encastrement dans les remblais cimentés afin de mesurer les variations relatives à l’effort et à la déformation des terrains durant l’exploitation minière et le chargement du remblai. Les données recueillies à l’aide de ces instruments ont servi au calcul du module in situ du remblai dans deux de ces mines. Le modèle numérique tridimensionnel de la semelle d’un remblai cimenté a été validé à partir des données recueillies par les extensomètres ancrés dans la voûte et dans la semelle de ces mines; ce modèle a ensuite été utilisé pour estimer le module de déformation à la troisième mine, étant donné que les palpeurs de pression des terres et les tensiomètres enfouis avaient relevés des variations négligeables. La matière d’agrégation de l’enrochement utilisée dans ces mines comportait entre 4 % et 8 % des composantes sèches par poids; le rapport eau-ciment se situait entre 0,42 et 1,0; et la taille des agrégats les plus gros dans ces trois mélanges était de 5 cm à 12 cm (2 po à 4,7 po). L’écart entre les valeurs calculées des modules de déformation in situ était grand, mais comme on s’y attendait, cet écart a été compensé par les valeurs modulaires des résidus cimentés et du béton tassé au rouleau avec des teneurs en ciment et des rapports eau-ciment semblables. [Als Teil der Sicherheits- und Stabilitätsstudien an drei Bergwerken in den Vereinigten Staaten von Amerika installierten Forscher Erddruckgeber und Einbindungsdehnungsmesser in zementierter Steinschüttung, um Spannungs- und Dehnungsveränderungen während der fortlaufenden Bergarbeiten und der Belastung der Steinschüttung zu messen. Daten von diesen Instrumenten wurden dazu verwendet, das In-Situ-Modul der Steinschüt-ung für zwei Gruben zu berechnen. Ein dreidimensionales numerisches Modell einer zementierten Steinschüttungsschwelle wurde mit den Daten von den im Grubendach und in der Schwelle verankerten Extensometern validiert; dieses Modell wurde dann dazu eingesetzt, um das Deformationsmodul in der dritten Grube zu schätzen, da die Erddruckgeber und Einbindungsdehnungsmesser nur geringfügige Messabweichungen feststellten. Das in diesen Gruben verwendete Steinschüttungsbindemittel variierte zwischen vier und acht Prozent an Trockenkomponenten nach Gewicht, der Wasser-Zementfaktor betrug zwischen 0,42 und 1,0 und die größte Zuschlagstoff-größe in den drei Mischungen schwankte zwischen fünf und zwölf Zentimetern. Die Reichweite der berechneten Werte des In-Situ-Deformationsmoduls fiel etwas breit aus, aber es fand erwartungsgemäß eine Klammerung der Modulwerte zwischen den Zemen-trückständen und dem durch Walzen verdichteten Beton mit ähnlichem Zementanteil und Wasser-Zementfaktor statt.]

By Basil Dimitriades

Five recently developed methods for determining nitrogen oxides in automotive exhausts have been evaluated from the standpoint of accuracy and applicability in current exhaust studies. Results showed that methods requiring conversion of nitric oxide to nitrogen dioxide as a part of the analytical procedure are subject to errors introduced by the instability of NO2. The extent of some of these errors has been determined and procedures have been developed to minimize undesirable influences. On the basis of the results obtained from this study, recommendations are made regarding procedures for batch type or continuous measurement of nitrogen oxides in exhaust streams.

Jan 1, 1968

By F. N. Kissell

The Bureau of Mines has successfully used sulfur hexafluoride (SF6) as a tracer gas to measure mine air flows under conditions where conventional methods have failed. SF6 was employed experimentally to measure accurately recirculation of return into intake air caused by leakage through an old stoped area, to check for potential leakage from an adjacent mine, to trace 10,000 cfm of “lost” air from an intake airway, and to measure transit air time through uranium mines. It proved useful as a means of accurately measuring airflow volumes in airways of large cross section and very low flow velocity, and in determining the recirculation resulting from underground cooling plants.

Jan 1, 1974

By Charles L. Kimbell

Tables 16 through 19 continue the series of providing the world merchant fleet distribution by type of vessel and the ranking of the major fleets by country of registry. Table 20 this year provides a summary of the world's liquid gas carrier fleet. These vessels are included in the totals given for the world's tanker fleet, but gives a breakdown demonstrating the growth of the importance of natural gas in the world's energy commodity consumption. Panama and Suez Canals Tables 21 and 22 provide the latest available information on the transit of mineral commodities through the Panama Canal, by number of vessels, direction, and the commodities transported. Although the number of vessels transiting the Panama Canal dropped slightly (0.5%) between 1989 and 1990, the total amount of cargo moved rose by 3.6% and the amount of mineral commodities moved rose by 7.2%.

Jan 1, 1993

By W. E. Lamont

The Bureau of Mines studied the potential for recovering marketable barite concentrates that meet oil well drilling-mud specifications from barite waste pond materials. The study was conducted as part of the Bureau's research program to conserve domestic mineral resources by advancing mineral recycling technology. The samples, which were obtained from Georgia, Nevada, Missouri, and Illinois, varied widely in character, particle size, and barite content. The samples were treated with sodium silicate and sodium cetyl-stearyl sulfate and then floated. The flotation flow sheet was modified to reject barren coarse and/or slime fractions from some of the samples, and one feed sample had to be scrubbed prior to flotation to remove residual flotation reagents. The cleaned concentrates had BaS04 contents ranging from 95.0 to 96.9 percent, while recovering 81.2 to 95.9 percent of the barite in the feed. The specific gravity of each concentrate exceeded the specification of 4.2. The removal of the flotation reagents from the flotation concentrate was not investigated.

Jan 1, 1982