Search Documents

By G. Sahasrabudh, G. DeIulii, K. P. Galvin

A novel agglomeration process has been developed, utilising a concentrated water in oil emulsion as a binder. The binder is typically 95 wt% water, the remainder being an organic phase containing kerosene and the emulsifier— sorbitan mono oleate (SMO) in equal mass portions. The binder can selectively agglomerate hydrophobic particles in less than 7 seconds. The agglomeration has proven to be highly effective in recovering any particle of virtually any size, provided the particle is hydrophobic. The approach has previously been applied to coal, magnetite and silica. In the paper, sodium isobutyl xanthate (SIBX) and its much longer chain version, potassium tetradecyl xanthate (C14X), were used separately as collectors to selectively agglomerate chalcopyrite from the ore. Xanthates attach to metal sulphides, thus hydrophobising sulphide mineral particles. Chalcopyrite is a sulphide mineral; however, it hydrolyses quickly in the presence of water. Ethylenediaminetetraacetic acid (EDTA) was used to remove the oxide layer formed at the surface of the mineral particles after wet grinding, leaving behind a freshly generated metal sulphide surface. After the EDTA treatment, the ore particles were quickly conditioned at an optimised pH as well as collector concentration and agglomerated. The agglomeration achieved a copper recovery of 75% within 7 seconds, consistent with the recovery achieved by flotation over much longer time scales. Keywords: Chalcopyrite, agglomeration, froth flotation, interfacial chemistry, X-ray fluorescence, selective hydrophobisation

Jan 1, 2020

By V. Labiouse, B. Heidenreich

The rebound phenomenon, which occurs during rockfalls when a rock block impacts with a slope surface, is influenced by several parameters related not only to the slope material but also to the block and the kinematics. The paper presents a small-scale testing campaign undertaken at the LMR (EPFL) to better understand and quantify the bouncing of blocks on granular slopes. The influence of some factors related to the ground material, the block and the kinematics is examined. Bei Steinschlägen wird die Flugbahn eines stürzenden Felsbrockens maßgeblich durch den Abprall vom Hang bestimmt. Der Rückprall hängt von verschiedenen Parametern ab, wobei nicht nur das Hangmaterial sondern auch Blockeigenschaften und Kinematik eine große Rolle spielen. Zum besseren Verständnis dieses Phänomens und seiner Quantifizierung werden am LMR (EPFL) kleinmaßstäbliche Versuchskampagnen auf granulären Materialien durchgeführt. Der vorliegende Artikel stellt die Versuche vor und untersucht den Einfluss verschiedener Boden-, Block- und kinematischer Parameter. Le phénomène de rebond qui se présente lors de l’impact d’un bloc rocheux sur la surface d’un versant dépend non seulement des caractéristiques du terrain, mais aussi de facteurs relatifs au bloc et à la cinématique. L’article présente une campagne d’essais sur modèle réduit entreprise au LMR (EPFL) afin de mieux comprendre et quantifier l’impact de blocs sur des matériaux granulaires. L’influence de divers paramètres relatifs au sol, au bloc et à la cinématique est mise en évidence.

Jan 1, 2003

By John W. Harbaugh, Alfredo Prelate

The goal of the study described here is to develop objective. quantitative methods for estimating the outcome probabilities of exploratory oil wells. The study employs the 're-experience' approach, in which historical data are used in a manner which attempts to recreate the past. Our past experience, of course, is the principal guide to the future. To appraise present-day oil prospects, however, we must analyze prospects that have been drilled in terms of how these former prospects were interpreted before they were drilled. An analysis of how they are interpreted after they were drilled is an inadequate guide to the future because our hindsight knowledge is superior to our foresight knowledge. Objective calculation of future outcome probabilities, then, requires that we attempt to treat past information in a manner analogous to that in which we must treat present information in forecasting future outcomes.

Jan 1, 2014

By T. C. Alex, K. M. Godiwalla, R. K. Jana

Manganese nodule, available in ocean beds, is a potential resource of the future for copper, nickel and cobalt. Recovering only these metals, containing less than 3% by weight, will result in the generation of large amount of residue. In addition to the material losses, several environmental and ecological problems arise out of this. The present study has been aimed at reducing the environmental and ecological problems associated with massive generation of this residue together with utilization of the resources. Presence of ~ 20% manganese and ~16% silicon in the residue has prompted us to check its suitability as a raw material for silicomanganese production. Lower manganese content and lower Mn/Fe ratio of the residue than that required for silicomanganese production has been corrected in this study by suitable blending. The efficacy of blending and its thermodynamic aspects using FACTSAGE software are discussed. The studies conducted indicate viability of bulk utilisation of the residue through silicomanganese production and thereby reducing the burden on environment to a great extent.

Jan 1, 2007

By Frank Johnson

Between 2000 and 2006, platinum production from the South African mines expanded from 206 to 307 tonnes (DME, 2007). Most of this additional metal has come from traditional ?narrow? reef stoping, generally taken to mean stoping in working places with a mining height of less than 1,5 metres. It is well known that narrow-reef stoping presents safety, technological and ergonometric challenges (Pickering, 2007). In planning for the expansion, which is still continuing, the platinum mining industry realized that it could not simply continue with traditional methods of narrow-reef mining. Particular issues identified were: ? High labour-intensivity: caused by use of hand-held rock drilling machines, labour-intensive support installation and stope cleaning; ? Dependence on rock-drillers: this occupation is no longer an attractive one and there is a reducing flow of new recruits; ? Safety: most of the work is performed close to the new faces, where there is the greatest exposure to the hazards of falling rock.

Jan 1, 2008

In the previous chapters we did not concern ourselves with the fact that the geostatistical properties of the regionalized variable x (z) are affected by the size of the support w. Ideally, when analysing an ore body O, we would like to determine the properties of point values in O, i.e. the properties of a regionalized variable with an infinitely small support, say w°. In practice, point values are never known. To measure the value of x at a point z we must take a sample of size w centred at z. For example, if we are interested in the grade at point z, w will be the volume of the sample 'centred in z; if we are interested in the metal accumulation at point z, w will be the area of the cross-section of the sample centred in z. We say that the measured property is a regularized variable, and so the semivariogram (or covariogram) calculated from the values obtained is also regularized. In the majority of the mining problems which can be solved by geostatistical methods, we are interested in the properties of blocks of ore and of samples with a finite non-point support. It will be shown in the following chapters that these problems can be solved by calculating the average value of the point sernivariogram in volumes or areas of finite dimension, or between such volumes or areas. These calculations would be simple if we knew the point semivariogram. This means that the point semivariogram has to be estimated from the observed regularized semivariogram(s).

Jan 1, 1978

By J. Muralha

The paper presents the limit equilibrium equations for the analysis of toppling blocks on a rock slope. The safety conditions are assessed by a numeric procedure implemented in an Excel worksheet. The UDEC numerical program was exploited to validate the procedure. A probabilistic model considering the spacing variability of the discontinuities was developed to define the most relevant parameters in this kind of problems. La communication presente les equations d’équilibre limite pour l’analyse de blocs rocheux sur une pente. Les conditions de securité sont évaluées par une procédure numérique en Excel. Le logiciel UDEC a été exploité pour valider cette procedure. Un modèle probabilistique a été developpé pour définir les plus importants paramètres dans ces problèmes. Das Referat stellt die Grenzgleichgewichtsgleichungen für die Analyse von umstrürzenden Blök-ken auf eines Felshang vor. Die Sicherheitsbedingungen werden durch ein numerisches Verfahren mit Excel beurteilt. Um die Gültigkeit des Verfahrens festzustellen, wurde das Programm UDEC benutzt. Ein die Klufabstandsvariabilität berücksichtigendes probabilistisches Modell wurde entwickelt, um die wichtigsten Parameter dieser Probleme zu bestimmen.

Jan 1, 2003

By A. P. I. Popoola, D. O. Okanigbe

Copper smelter dust (CSD) is a byproduct of copper smelting and is composed of considerable amounts of copper values and also contaminants (like silica and mullite). Silica in CSD forms Siloxane, a low density material, which is difficult to separate from the aqueous phase during solvent extraction. The need therefore arises to reduce/remove the aluminosilicates for better grade and recovery of copper in subsequent processes. This paper reports the use of two types of centrifugal gravity concentrators, namely Knelson (KGC) and Falcon (FGC), for upgrade of copper in CSD. The aim was achieved by an initial characterisation (Particle Size Distribution (PSD) and mineralogical analysis), together with Density Separation (DS) experimentation, premised on a hypothetical density difference between copper oxide and silicon/aluminum oxide. Wet screening results showed that 88.52 % of CSD particles were in -53 μm fraction. Further PSD study using laser diffraction showed the -53 μm fraction to be composed mainly of 26 μm, 22 μm and 18.5 μm fractions. Mineralogical analysis showed copper to occur mainly as oxides (24.34 wt%), but also as sulphides (7.95 wt%), and a substantial amount of aluminosilicates (42.97 wt%) were identified. Density of CSD was determined as 2.83 g/cm3. Copper content (18.02 wt%) in CSD was upgraded to 35.94 wt% in concentrate using KGC. In conclusion, the results showed good convergence between hypothesis and experiment. Additionally, it was also concluded that KGC performed better than FGC for copper upgrade in CSD. However, roasting CSD prior density separation was recommended for enhanced copper upgrade. Keywords: Copper smelter dust, density separation, solvent extraction, mineralogy

Jan 1, 2020

By P. R. Jochens

South Africa depends to a considerable measure on the exploitation of mineral reserves and the processing of these minerals. One of the prime requirements for the mining and metallurgical industry to continue in this vital role is access to sufficient energy in a suitable form. Hence, four important questions are discussed: Does South Africa have sufficient energy for the processing of its minerals and metals! Will the cost of energy allow South Africa's minerals and metals to compete on world markets? Can mining and metallurgical processes become more energy-efficiency Can mining and metallurgical processes be adapted to the various forms of energy that may have to be utilized in the future? It is concluded that about 26 per cent of the extractable reserves of coal would be required in the mining and processing of 50 per cent of South Africa's reserves of gold, platinum-group metals, copper, iron, ferrochromium, and ferromanganese. However, the reducing agents required exceed the extractable reserves but not the total estimates of mineable in situ resources of metallurgical coal and anthracitic coal. Even under the severe constraint that coal could become virtually the sole source of energy, only about three-quarters of the extractable reserves of coal would have been consumed by the year 2025. The reasonably assured resources of uranium metal that can be recovered at less than $80 per kilogram are considerable and, at current conversion efficiencies to electricity, are equivalent to one-fifth of the extractable reserves of coal. The rate of exportation of energy in the form of U30. was about five times that of coal in 1978. It is pointed out that the price of energy has a direct effect on the competitiveness of metals, and, although constituting only a small proportion of the selling price of precious metals, it represents a significant proportion of the selling price of copper and metals recovered from oxide ores. The scope for the conservation of energy appears to be greater in the extraction and conversion of primary energy-carriers to electrical energy than in other mining or metallurgical fields. Provided that alternative sources of energy can be converted to electrical energy, they can be applied to the mining and metallurgical industries. The decision as to which type of energy should be used in specific mining and metallurgical situations is complicated, and is likely to be subjected to closer scrutiny than in the past. The hope is expressed that the tentative conclusions reached will give rise to more-quantitative analyses from those qualified to undertake such an exercise. Inevitably, the questions asked at the outset give rise to more questions, and the more interesting ones are posed in the context of each conclusion.

Jan 1, 1980

By D. Das, B. K. Nandi

The present study focuses on utilising the electrocoagulation (EC) process for the treatment of process water generated in an iron ore beneficiation plant for safe discharge and reuse. Removal of heavy metals like Fe, Cr, Cu, Zn, Mn and Pb which was found in higher concentration along with some other impurities exceeding the permissible and discharge limit were attempted. The influence of different electrode material, current density, inter-electrode distance, and solution conductivity was explored for effective removal of the metal ions. Experimental results infer that almost 99.95% Fe, 97.77% Cr, 73.44% Cu, 99.34% Pb and 88.69% Mn was removed using aluminum electrodes at monopolar mode at a current density of 68.50 A/m2, inter-electrode distance of 1 cm and solution conductivity of 1.033mS after 60 min of EC. In addition, removal of other toxins like TDS, turbidity, salinity and conductivity etc. was also assessed during the process. Removal of such heavy metal ions by EC was found to follow 1st order kinetics with electric energy consumption of 3.93 kWh/m3, electrode consumption of 0.1191 kg/m3 and operating cost of 0.6115 US$/m3 respectively. Keywords: Fe removal, electrocoagulation, Al electrode, turbidity

Jan 1, 2020

By J. Petersen, K. Shaik1, H. Kolev, Z. Cherkezova-Zheleva

Sperrylite is one of the most abundant platinum minerals globally, valued for its economic importance but also known for its highly refractory nature, making it difficult to process via the conventional route. This study explores the oxidative leaching of sperrylite using a cyanide–ferricyanide system, with a key focus on characterisation of the mineral and surface speciation under varied leaching conditions using x-ray photoelectron spectroscopy. The parameters investigated include the effect of sodium cyanide concentration, the use of potassium ferricyanide as an oxidant, copper sulphate pentahydrate as a catalyst, as well as the effects of temperature and particle size. A limited set of leaching tests was carried out to study the surface chemistry rather than optimising dissolution conditions. This approach identified mineral oxidation states and shifts in binding energies, prior to and post leaching. XPS analysis of sperrylite’s surface chemistry identified key species, comprising the bulk Pt(II)–As (≈73 eV) and As(–I)–Pt (≈41.8 eV) states, together with surface oxidation products Pt(II)–O (≈72 eV), Pt(IV)–O (≈74.5 eV), As(III)–O (≈43 eV) and As(V)–O (44.5 eV). Leaching led to the removal of pre-existing oxides on the ultra-finely ground sample, exposing the underlying bulk species. In contrast, the crystalline sample with an initial low concentration of oxides, generated higher amounts of fully oxidised species after leaching, reflecting greater surface reactivity.

Mar 6, 2026

By M. Dworzanowski

The difference in the magnetic properties of minerals is the basis for magnetic separation. All minerals can be generally classified as ferromagnetic (strongly magnetic), paramagnetic (weakly magnetic) or diamagnetic (non-magnetic). Magnetic separation can be conducted dry or wet. The majority of the applications of wet magnetic separation in the mining industry are based on the wet drum magnetic separator. The wet drum magnetic separator has been in use for over 50 years and its design is based on a rotating drum installed inside a tank. Inside the drum are stationary, permanent magnets arranged in an arc to provide the magnetic field. These magnets can be of the ceramic ferrite type providing a low intensity magnetic field or of the rare earth type providing a high intensity magnetic field.

Jan 1, 2010

By Karl-H. Daum

Over many decades, numerous feasibility studies have demonstrated, that the production of sulphuric acid remains the most viable option of sulphur recovery from smelter off gas and abatement of SO2 emissions to the atmosphere. This is particularly more pronounced as smaller but more concentrated off-gas flows are to be treated from smelters, and enhanced sulphuric acid processes be-come available. Off-gas handling systems represent a significant capital and operating cost burden to the metallurgical operation. Modern pyrometallurgical smelter processes for sulphide ores based on the use of oxygen-enriched air, produce relatively small off-gas flows with high SO2 concentrations in the smelter gas of 30?60 %-vol. of SO2. This is a prerequisite for substantial cost reductions in the smelter off-gas handling and treatment system. As an alternative to sulphuric acid production, numerous scrubbing concepts with alkali or dual-alkali combinations as well as organic absorbents have been proposed. Also the reduction of the SO2 to elemental sulphur has frequently been studied. Very few of those alternative processes have been built in industrial scale, but all were generally characterized by none sustainable operation due to cost reasons, problems with issues related to chemicals used and by-products or poor availability. Thus the traditional concept of converting the SO2 to sulphuric acid is most common, although regarded as un-economic, but is at least a proven, environmentally sustainable and reliable way of sulphur gas processing. With the high acid price levels these days, operating companies are even able to generate significant revenue with their otherwise ?fatal? acid. Even though smelter gas is available at high SO2 concentrations, in a conventional acid plant one would add large amounts of air to dilute the gas down to a suitable concentration of 12?13 (14) %-vol. SO2. Dealing with higher SO2 concentrations in smelter acid plants is not feasible, as the gas exit temperature of the catalytic oxidation step would exceed the allowable limit for the catalyst. Hence those conventional acid plants are characterised by the use of large equipment, i.e. high capital cost, high energy consumption and limited flexibility. The newly developed LUREC® process can handle off-gas with significantly higher gas concentrations, even in excess of 25 %-vol. SO2. It is entirely based on well-proven equipment and unit operations. The first industrial application, operating with 16?18 %-vol. SO2 will be presented in this paper, along with the fundamentals of the process. It will be demonstrated that the process requires inherently lower capital cost, fewer operating cost, offers better energy recovery and lower emissions as compared to conventional design. While most existing smelter acid plants would have some built-in spare capacity, any significant increase of smelter capacity, say of 30%, can basically not be accommodated without installing an additional parallel new acid plant unit. An add-on LUREC® module can remove any such restriction, while simultaneously de-bottlenecking the existing acid plant. The paper also discusses the present status of the add-on technology for smelter acid plant expansions with respect to technical boundary conditions of different process alternatives as well as economic and environmental aspects. Application of the LUREC® process to modern smelter acid plants operating with high SO2 gas concentration, will lead to a substantial reduction of the specific size of the gas processing equipment and equivalent savings in capital and operating cost. The LUREC® process is patented worldwide by OUTOTEC.

Jan 1, 2009

By Adams. M. D.

Most of the cyanide lost in carbon-In-pulp plants is due to the reaction of cyanide with base metals and sulphides during leaching. Some cyanide is also lost in the adsorption tanks as a result of oxidative and adsorption reactions with the activated carbon. The high rates of cyanide loss in the elution and electrowinning stages are atributable to hydrolytic decomposition and anodic oxidation, respectively. However, the relative amount of cyanide lost during these two stages is small for a given amount of ore treated.

Jan 1, 1990

By H. Wagner

During the last few years a large number of pillars in different mines were investigated. Pillar conditions were evaluated using subjective, empirical, geophysical and numerical methods. A critical comparison of the different methods showed some interesting coherence. This paper concentrates on experiences using the p-wave velocities as an indicator of pillar conditions. Während den letzten Jahren wurde eine große Anzahl von Bergfesten in verschiedenen Bergwerken auf ihren Zustand hin untersucht. Hierzu wurden subjektive, empirische, geophysikalische sowie numerische Methoden angewandt. Dieser Vortrag beschäftigt sich mit den Erfahrungen beim Einsatz der p-Wellengeschwindigkeit zur Beschreibung des Festenzustandes. Le condition géotechnique d’une grand nombre des piliers des mines souterraines différentes sont examinées ces dernières années. On a appliqué des méthodes subjectives, empiriques, géophysiques et numériques. Ce rapport occupe aux expériences avec l’application de la vélocité des ondes de compression pour tracer le condition des piliers.

Jan 1, 2003

By Huanhuan SU, Jianqiang Zhang, Zhongyuan Liu, Junwei Ma

The high-sulfur bauxite in Henan Province was used as raw material. The grinding fineness, pH value and collector dosage on its desulfurization performance, and industrial flotation desulfurization process were studied. The best flotation desulfurization conditions were grinding fineness of 75%, pH of 8.5, and collector of 600 g/t. “One coarse, one cleaning and one sweep” closed-circuit flotation was established as the industrial flotation desulfurization process. After the closed circuit test, the sulfur content of aluminum concentrate with the yield of 93% was 0.23%, and the sulfur removal rate was 83.16%, and the sulfur content of tailings (sulfur concentrate) was 15.09%. Keywords：High-sulfur bauxite under coal mines, flotation, desulfurization

Jan 1, 2020

By E. Maritz

"The localized uniform conditioning (LUC) technique was proposed by Marat Abzalov in 2006. The technique converts conventional uniform conditioning (UC) grade-tonnage curves into single grade values attached to each smallest mining unit (SMU). This is achieved by ranking the SMUs within a panel in increasing order of their grade (based on the direct kriging of SMUs). This ranking is then used to localize the conventional UC grade-tonnage curves for each panel by dividing them into classes and computing their mean grades, which are assigned to the SMUs. The quality of this localization process will depend heavily on the validity of the grade patterns predicted by the direct kriging of the SMUs. Abzalov noted that where the distribution of data available for the direct kriging of the SMU is characterized by strong short-range variability, the advantages of using the LUC approach may be more limited. Consequently, a study was undertaken to determine how valid the predicted grade patterns of a typical Birimian-style gold deposit (with high nugget effect and strong short-range variability) might be expected to be. This was determined by comparing the direct SMU kriging ranking (based on sparse data) with the grade control model ranking (based on close-spaced data and the best available estimate of the deposit). The results showed a satisfactory correlation between these rankings and it was concluded that, although the grade patterns predicted by the direct kriging of the SMUs may be less meaningful for deposits exhibiting strong short-range continuity, there is nevertheless a convincing relationship with the actual (or best available) rankings. Therefore, the LUC technique is still considered to be useful for this style of deposit. IntroductionFor adequate technical and financial evaluation of a project, attempts should be made to estimate the recoverable resources – the portion of the in situ resource that can be economically extracted by mining. To achieve this, the estimates of the tonnage and grade of the mineralization should be produced above a given economic cut-off and should take into consideration the proposed mining selectivity."

Jan 1, 2016

By R. B. Khumalo, M. S. Nyarela, R. C. Nemathithi

Palabora Mining Company is one of the largest low-grade copper mines globally. The mine uses block caving for the extraction of the orebody. This paper enumerates the drawpoint loading strategies for the overall head grade improvements, particularly for a block that is nearing depletion. A comprehensive literature review of various considerations relating to improving productivity in block caving is presented to contextualize the draw control in caving. From this study, an optimized draw control strategy is presented, which focuses on three parameters that include grade distribution, loading compliance, and tonnage splits per sector. An empirical method based on the relational study between various parameters is used to outline the key criteria to be used in the optimization of drawpoint loading in block caving.

Nov 30, 2022

By J. P. Gouvea, T. R. Stacey

A research project was carried out on a gold mine in the Vaal River region of South Africa (Witwatersrand Basin) to evaluate the effect of two particular aspects of rockbolt installation – the angle of inclination of the bolt relative to the orientation of the rock surface, and the protruding length of the bolt – on the mine’s gully support system. A keyblock analysis approach indicated that these factors do not have an adverse impact on the stability of the strike gullies. This was confirmed by extensive empirical data collected from the case study mine. While safety is the primary concern, cost saving opportunities can be realized through reconsidering historically inherited support standards that are perceived to be correct and appropriate. The research described in this paper sets forth a practical approach, that is easy to implement and repeatable, to evaluate the role of rockbolts in stoping gullies.

Feb 12, 2024

By S. Dey, C. Bhar, S. K. Mandal

Loading and hauling of ore and waste are the key operations of an opencast coal mine and entail a high operational cost. The productivity of a mine can be increased by reducing the cycle time of loading equipment as well as utilizing dumpers optimally. In this paper we discuss the impact of rock type, bucket fill factor, rock fragmentation, the height of the cut, and angle of swing of the bucket on shovel performance. A time study is conducted on shovels in an opencast coal mine with experimental blasts of rocks to assess the impact of different factors on the performance of the shovel. Based on the data, the authors applied multiple regression (MR) and artificial neural network (ANN) techniques to develop different models for the prediction of the shovel cycle time. Developed models are validated by comparing the predicted data with actual field data. With the help of the best model, the plausible fleet size is determined in order to utilize the shovel and dumper optimally and to improve the performance of shovel–dumper operation.

Oct 1, 2022