Search Documents

By N. A. Barcza

An investigation was conducted into the reactions between the slag system MnO-CaO-MgO-SiO2(AI2O3) and the alloy system Mn-Fe-Si-(C). Synthetic slags representative of plant melts and a plant alloy were reacted in alumina crucibles at temperatures of 1400°C, 1450°C, 1550°C, and 1600°C. In similar experiments, slags were used that comprised a South African manganese ore with various amounts of lime and several synthetic alloys with various silicon contents and manganese-to-iron ratios. These experiments were conducted in a vertical molybdenum-wound resistance furnace with full temperature control. Slag-to-alloy ratios were also varied during the tests. The rate of reduction of Mn.O3 and the MnO from the slag by the silicon in the alloy was extremely rapid, most of the reaction being completed within five minutes. The strongly exothermic nature of the reaction resulted in considerable generation of heat at the slag-alloy interface, causing convectional stirring of the contents of the crucible and promoting the rate of reaction. Equilibrium was usually attained after fifteen minutes. The major limitation governing the recovery of manganese is the need for the silicon content of the alloy to meet a maximum specification of 2 per cent. Higher concentrations of silicon in the final alloy of between 8 and 12 per cent favour good recoveries of manganese from the slag, but, since such an alloy is not salable, lower recoveries must apparently be tolerated. In alloys of 2 per cent silicon, low activities of the silicon are responsible for poor recoveries of manganese. The activity of MnO in the slag can be increased by moderate additions of CaO and small amounts of MgO, i.e., by an increase in the basicity of the slag.

Jan 1, 1979

By C. Botha

The South African democratically-elected government instituted policies and legislation that are intended to bring about change and transformation in the country and have drastically affected different industries, among others, the mining industry. The Mineral and Petroleum Resources Development Act 28 of 2002 (MPRDA) and the Broad-based Socio-economic Empowerment Charter (Mining Charter) were introduced in order to redress previous inequalities and to promote women?s employment in the mining industry. This research evaluates the practical implementation of the MPRDA and the Mining Charter with specific reference to women in underground mining. A quantitative research paradigm was used. Data were collected through a process of a face-to-face interview surveys utilizing a structured questionnaire. The research setting was limited to the platinum-mining industry in the area of Rustenburg in the North West Province. The study population consisted of 195 available women working undergound at the mine. It is clear from the findings that mining companies are facing major challenges in their attempt to incorporate women in underground mining activities. Company policies regarding these issues must be firmly in place; however, the challenge lies in the translation of these policies into practice. In this regard, managers will have to play a leading role in the successful phasing in of women into the underground mining arena.

Jan 1, 2012

MEMBERSHIP In terms of By-laws7.7.1 members are hereby notified that the membership of the following has been cancelled and their names removed from the Membership Register: H. Digby Roberts, R. J. P. van Tonder, S. D. Williams (Members), A. I. de Klerk, M. F. Ford, A. W. Hine, H. A. Johnston, R. T. Joyner, H. D. Small, P. White (Associate Members), J. de F. Agrella, A. Leibowitz (Affiliates), J. P. M. Maidment, C. P. J. M. Steyn (Graduates), H. C. M. Fourie, B. C. P. Job, J. P. Kruger, E. C. Nicolas, A. P. Prinsloo, B. Schuitema (Students). INSTITUTE PUBLICATION Transactions of the Seventh Commonwealth Mining and Metallurgical Congress Requests are still being received by the Institute for sets of the above transactions. Members who wish to dispose of sets in good condition are requested to contact the Secretary, P.O. Box 1183, Johannesburg or 304 Kelvin House, Johannesburg. As these are for resale a price of not more than R10.00 can be offered per set of three volumes. INTERNATIONAL SOLVENT EXTRACTION CONFERENCE, 1971 The Society of Chemical Industry has agreed to sponsor an International Conference devoted to the science and technology of solvent extraction. This will be held in The Hague in the Netherlands during the week commencing 19th April, 1971. The organisation of the Conference will be in the hands of a Conference Committee under the chairmanship of Mr B. F. Warner. The emphasis of the Conference will be on technical solvent extraction of both inorganic and organic substances, including basic principles and practical applications. Sessions are envisaged covering the chemistry of solvent extraction, industrial processes and economics, the performance of contacting equipment and the underlying phenomena involved, and the response characteristics and control of such units. The Conference Committee will welcome offers of papers for presentation at the Conference. In the firts instance, intending authors should submit a preliminary title and an indication of the scope of their contribution to the Conference Secretary: Dr. C. Hanson, University of Bradford 7, U.K. It is hoped to have available in September a first circular giving further details of the Conference. Copies may be obtained from: International Solvent Extraction Conference, 1971, 14, Belgrave Square, London, S.W.1. SOUTH AFRICAN TUNNELLING CONFERENCE TO BE HELD IN 1970 A South African Tunnelling Conference, to be known as TUNCON 70, is to be held in Johannesburg during the latter half of July, 1970. South Africa, in common with other countries, has a vital and growing interest in tunnelling. Apart from the 800 kilometres of tunnel excavated annually in the gold mines, the 82 kilometre-long Orange-Fish Tunnel is being driven to carry water from the Orange River to the drier areas of the Eastern Cape Province. This and the realization that services such as water and transport are increasingly being carried underground in various parts of the world have emphasized the need for a forum at which the technology and potential of tunnelling can be discussed. TUNCON 70 is being supported by three professional engineering societies representing some 6,000 engineers, namely, the South African Institute of Mining and Metallurgy, the South African Institute of Civil Engineers and the South African Institution of Mechanical Engineers, as well as by the Geological Society of South Africa. The conference has three main purposes. Firstly, to pool and exchange expertise by authorities on tunnelling; secondly, to discuss future developments in tunnelling technology with the aim of making those concerned with long-term planning aware of the potentialities of tunnelling; thirdly, to propose standards for tunnel shapes and sizes. Adoption of standards for tunnelling equipment and accessories would be a major step forward in improving tunnelling efficiency. The five themes of the conference will be: tunnel utilisation, exploration, design, construction and standards. The conference will be held at the University of the Witwatersrand, Johannesburg, from 21st to 24th July, 1970. Arrangements will be made for visits to be paid to mines and tunnelling projects before the start of the conference. Further information is obtainable from the Organising Committee, TUNCON 70, P.O. Box 1183, Johannesburg, South Africa.

By G. Song, X. Liu

The global coal industry has changed significantly in recent years. In this paper we analyse the coal production and consumption, imports and exports, and coal prices in China and other major coal-producing countries during the past four decades. The analysis shows that global coal production and consumption have declined over the last three years, in striking contrast to the continuous growth for most of the past 35 years. Australia, Indonesia, and Russia have become the world’s major coal providers, while China, India, and the USA, and Germany are the major coal consumers. The world’s, and China‘s, coal industry can be classified into four stages of development: the stable growth phase, stable phase, rapid growth phase, and high-quality phase. Coal prices rose in the world’s four major coal markets in 2016 after four consecutive years of falling prices. The elimination of overcapacity and production-optimizing operations in China could assist in achieving a demand and supply balance.

Aug 8, 2024

By S. R. Grobler, S. Bilessuris, M. E. Greenway

Ensuring that all the head ropes on a multi-rope friction winder share the load equally has been a design and maintenance issue since they were first developed. Accurate machining of the rope grooves is necessary to meet this objective. Early analysis of the change of rope loads for ropes in grooves that are mismatched in depth treated the grooves as rigid. Groove depth tolerances deduced from this analysis are stringent and difficult to achieve in practice. Test work indicated that the inherent flexibility of groove lining materials alleviates the load-sharing problem. However, no analysis of rope load changes due to mismatched flexible grooves has been published. In this paper we develop new equations for the rope load variation for flexible grooves. By allowing flexibility to reduce to zero, the corresponding rigid rope groove equations are obtained. New criteria for tolerable groove depth variations are developed from this analysis, which depend on the flexibility of the groove lining material.

Sep 1, 2021

By E. Rex, T. J. Goff, W. S. B. van Beek, P. E. Nel

"The PGM smelting industry is known for operating at significant high superheats. Both the slag and matte phases that separate via gravity need to be tapped out of the furnace in a safe and efficient manner, which can be achieved only through sound tap-hole management practices. This paper gives an overview of the tap-hole management approach followed in the operations at Lonmin’s Western Platinum Smelter.Five circular AC furnaces are operated, with each furnace comprising essentially a crucible and auxiliary equipment. Within the crucible, slag and matte tap-holes are situated at different elevations. The slag phase is tapped at a higher elevation than the matte phase. At the three older furnaces, tapping is done by the conventional method of lancing open the tap-hole and closing it with a dolly. However, at the two newer furnaces, tap-holes are opened and closed with the aid of a drill and mudgun.Tap-hole management can be divided in a number of aspects. In order to achieve a safe opening and closure every time, Lonmin distinguishes between three important aspects - the design of the tap-hole system, the operating practices followed, as well as care and maintenance. This paper briefly describes the tapping channel and cooling requirements for handling superheated matte, together with the difference in design of the matte and slag tap-holes. Mention is also made of the importance of auxiliary equipment, which includes the launders, fume extraction, granulation water, and mudgun and drill units. Improvements made to the matte tapblock design are discussed.The monitoring, alarm, and safety systems related to matte and slag tapping are described. Tap-hole life and different wear mechanisms are mentioned. Tapping can be done safely only if the tap-holes and equipment are maintained properly. Mention is made of the tap-hole refractory repair practices, and the improvements made in order to reduce repair time as well as to extend the time between deep repairs. The importance of the correct tap-hole clay selection in order to nurse the tapping channel after each tap is also discussed.The paper finally touches on some research and development work that was done in order to improve the monitoring of the condition of the tapblock by means of fibre optic temperature sensors"

Jan 1, 2014

Acid heap leaching has been extensively applied to the processing of copper oxide ores, with recovery of copper by solvent extraction and electrowinning. Heap leaching has also been extended to the treatment of secondary sulphide copper ores, where oxidative conditions are generated in aerated heaps by the bacterially-assisted oxidation of ferrous iron to ferric iron. The treatment of low-grade chalcopyrite ores has recently been the focus of research, with Mintek playing a prominent role. When processing chalcopyrite ores, more complex column test work is performed, which incorporates the prediction and simulation of temperature behaviour in pyrite-containing heaps. Mintek has devised a trade-marked column leaching apparatus (SmartColumn?) for the simulation of the natural temperature profile development in pyrite-containing heaps. As heap leach applications are becoming more complex, the parameters that need to be built into the design and operation of heap leach plants are growing in number, and the amount of data to be collected and processed, and the number of decisions to be taken daily, are also increasing. Mintek has therefore developed the HeapStar® administrative advisory software, as a guidance system to ensure that the correct protocols are implemented at various stages of the leach cycle.

Jan 1, 2012

By J P. van Dyk

The dramatic strengthening of the rand against the dollar as well as a decline in quantity and quality of locally available concentrates have had a dramatic impact on Zincor?s operations during the previous two years. Zincor has responded with the implementation of a number of technical improvements to the process to decrease cost and increase revenue and plant flexibility. Among the initiatives is the pre-leaching and pelletising of the zinc concentrate, de-bottlenecking and process improvements in the leach and purification circuits, the introduction of cathode washing and automated cathode stacking in the cell house and the installation of a new furnace to produce pre-alloyed jumbos. This paper will describe these initiatives and others that Zincor have recently taken to stay competitive in changing global base metals market.

Jan 1, 2005

By R. Ciccu

This paper examine the optimization of a beneficiation plant for recovering marketable barites from crude ores of different characteristics. The plant, part of a mining complex in Sardinia, consists of a jig section integrated with a flotation line. The problem has been studied using a suitable model of the process, based upon experimental and field data pertaining to both the characteristics of the feed material and the performance of machinery. Data have been automatically processed with the aid of a computer to find the optimum setting of each section, in order to maximize profit for each kind of ore separately fed to the plant. Moreover, the advantages of blending the various concentrates - not all of them individually marketable - are also demonstrated. The overall economic result can be improved provided suitable proportions of each kind of ore are fed to the plant. Such information is fundamental for the long-term planning of exploitation of available reserves, and provides guidelines for further prospecting. The paper illustrates the washability characteristics of the ore's and describes in detail the model adopted. The results of data processing are then presented in the form of computer graphs and discussed. Finally, conclusions are drawn regarding the advantages of resorting to Operations Research as an aid to management.

Jan 1, 1987

By P. Altounyan, K. Akermann, T. Van den Berg

Amandelbult Mine is currently undertaking a trial to mechanise the mining of the UG2 reef through the introduction of room and pillar mining. As part of the trial, a system of managing the control of the hanging wall has been introduced, based on systems and technology that are proving successful in the nearby coal mining industry. The principal features are the use of a high bond strength, stiff bolting system which can be easily installed to a high standard, and a range of in situ tests and measurements to optimise the level of support installed to control the movement of the hanging wall. The rock bolt system and the measurements and tests described are new to the platinum mining industry. The paper describes these systems and their adaptation and application to hard rock mining. La Mine d’Amandelbult est actuellement dans des essais en vue de mécaniser l’extraction dans la veine UG2 grâce à l’introduction d’une exploitation par chambres et piliers. Dans le cadre de ces essais, un système de gestion de la paroi suspendue a été introduit, base sur des systèmes et une technologie qui prouvent donner de bons résultats dans l’industrie voisine d’extraction de la houille. Les caractéristiques principales sont l’utilisation d’un système de verrouillage raide et à forte adhérence qui peut être installé à un haut niveau de qualité et une gamme d’essais et de mesures in situ pour optimiser le niveau de soutien installé pour contrôler le mouvement de la paroi suspendue. Le système de verrouillage de la roche ainsi que les mesures et les essais décrits sont une nouveauté dans l’industrie minière du platine. La communication décrit ces systèmes ainsi que leur adaptation et leur application à l’exploitation minière en roche dure. Amandelbult Mine unternimmt gegenwärtig einen Test um den Abbau des UG2 Riffs durchEinführung des Kammerpfeilbau zu mechanisieren. Als Teil dieses Tests wurde ein System zur Kontrolle der Stollenfirstes eingeführt, welches auf jenen Systemen und Technologien basiert, diesich im nahe gelegenen Kohlebergbau als erfolgreich erwiesen. Die prinzipiellen Charakteristikasind der Gebrauch von einem steifen Bolzensytem mit hohem Verbundwiderstand die leicht zueinem hohen Standard gebracht werden können, und eine Reihe von in-situ Tests und Messungenum das Niveau der installierten Unterstützung zu optimieren, und um die Bewegung desStollenfirstes zu kontrollieren. Das Gesteinsbolzensystem, die Messungen und die Tests, diebeschrieben werden, sind neu in der Platinbergbauindustrie. Diese Arbeit beschreibt diese Systeme, deren Anpassung und Anwendung im Hartgesteinsbergbau.

Jan 1, 2003

By M. S. Shishvan, J. R. van Duijvenbode, L. M. Cloete, M. W. N. Buxton

Geochemical and mineralogical datasets from Tropicana Gold Mine, Australia, have been used to define ore fingerprints. VNIR/SWIR spectral data were represented by four normalised wavelength regions and were clustered to form spectral classes. Sequentially, these spectral class proportions within a block and collocated XRF data were clustered to form material types (fingerprints). The material types were related to an Equotip-BWi correlation. These correlations can be used to extrapolate a hardness signature and generate a BWi proxy for different blocks. The combined fingerprints and BWi proxy can assist as a tool for enhancing the prediction of comminution behaviour. They can explain specific domain-related hardness variations. For example, one material type could be separated into a softer (~15-18 kWh/t), and harder (>20 kWh/t) material blend. This was accomplished using the commonly overlooked VNIR region at 605 nm. This outcome has significance for blending strategies.

Sep 1, 2021

By M. Khodadazadeh, K. G. van den Boogaart, T. Leißner, L. Tusa, J. Gutzmer, R. Gloaguen, M. Kern

Ore sorting is a technology that is increasingly used to process primary raw materials. Timeconsuming and expensive empirical state-of-the-art test work is carried out to assess whether the use of ore sorting for the enrichment of a particular ore makes technical and economic sense. With the innovative simulation-based approach presented here, it is possible to direct the selection of a suitable sensor based on quantitative mineralogical and textural data, thus avoiding much of the empirical studies. Required data can be collected quickly and cost-effectively using available methods of automated mineralogy. The obtained parameters such as mineral grain size distribution, modal mineralogy, mineral area and mineral density distribution have been utilised in this study to simulate the prospects of success of ore sorting, applying different types of sensors. Empirical tests with commercially available sensor systems have been conducted to experimentally validate the predictions of the simulations. The estimation of the target mineral grade can be further optimised by the use of machine learning algorithms for the integration of automated mineralogy data and sensor data. The approach can easily be adapted to other types of raw materials and thus has great potential to become a key technology for the optimisation of processing experiments. Keywords: Automated mineralogy, hyperspectral imaging, machine learning, ore sorting

Jan 1, 2020

By L. I. Boshoff, S. Gracie

This paper discusses pilot and laboratory-scale metallurgical test work conducted on bulk samples from a low grade heavy mineral deposit and provides an overview of basic practical metallurgical techniques applied to ascertain the suitability of existing production plants to process material from this orebody. Previous investigations have shown this specific orebody to be more challenging in terms of mineral beneficiation as it has a high gangue mineral content. Test work was conducted on targeted stratigraphic units based on lithology and assay results to enable identification of the stratigraphic units portraying quality issues. Unit specific metallurgical pilot work has never been conducted on any of the RBM orebodies and is a new field currently being explored. During this investigation focus was placed on potential quality and yield issues for ilmenite product, with particular reference to CaO quality. A basic evaluation of zircon and rutile separability was also conducted. The test work was conducted using a comparative baseline methodology with metallurgical test work methods specifically aiming at mimicking the existing production plant as closely as possible. This enabled not only the likely metallurgical performance to be assessed but also indicated whether current plant design would be suitable to process the low grade ore types into products of acceptable quality at acceptable yields. The methods and findings discussed in this paper indicate that although there is considerable variation between different units, a blended feed can be successfully processed. With unit specific metallurgical data applied to the existing geological block model, expected yields and recoveries using current plant designs could be predicted.

Jan 1, 2007

By K. Isaac, S. O. Bada

This research focuses on the co-firing of discard coal with refuse-derived fuel (RDF) to utilize this abundant resource in South Africa for energy generation and reduce the volume of waste disposed of at landfills. The potential of a coal with a high ash content (> 40%), which is a grade used in some power stations in South Africa, and its combustion compatibility with two different RDFs in terms of emission reductions has been established. Gaseous emissions and ash residues from the combustion and cocombustion of the coal, two different RDFs and coal/RDF blends of different proportion were analysed. One of the RDF samples contained mostly paper (PB) and the other mostly plastic (PL). Co-combustion ash from the discard coal and RDFs showed a decrease in chloride and alkali metal contents as the coal ratio in the blend increased. The slagging propensity of the co-fired blends was found to be very low, while the propensity for fouling decreased from high to medium for all the blends with < 75% RDF. Cocombustion of RDF with coal showed a decrease in SO2 emissions from 387 ppm (discard coal) to 50 ppm for the sample containing 25% coal discard plus 75% PL. A 15% PL to 85% coal blend also reduced NOx emissions from 145 ppm (100% PL) to 88 ppm. The lowest CO2 emission observed was 6000 ppm for the blend of 85% discard coal plus 15% PB. It was established that the most favourable fuel blend that can produce the lowest sulphur emissions if used for power generation is the 25% coal discard plus 75% PL sample.

Aug 2, 2022

By J. Bai, C. Zang, W. Yuan, L. Zhuang

"This study evaluates the efficiency of using mechanochemical reduction to assist the extraction of zinc from zinc ferrites by alkaline leaching. The transition of zinc ferrite into a metastable state after mechanochemical reduction with metallic iron contributes to the ready dissolution of zinc from the activated zinc ferrites in alkaline solution. Zinc ferrites were mechanochemically reduced under conditions of Fe:ZnFe2O4 mole ratio of 2:1, using 5 mm diameter stainless steel balls as the activation medium at a mass ratio of balls to raw materials of 25:1. Subsequent leaching in 6 mol/L NaOH solution at 90°C resulted in more than 70% Zn extraction. These results may be used to further develop a hydrometallurgical process for recovering zinc from zinc ferrites in alkaline solution.IntroductionZinc is an important nonferrous metal required for various applications in batteries, solder, dielectric materials, and piezoelectric materials. High-grade, easily concentrated ores are becoming scarcer: to meet world demands for zinc, it is necessary to develop economical and environmentally safe metallurgical technologies that use secondary materials such as leach residues of roasted zinc concentrates and electric arc furnace dusts. The zinc in the majority of these wastes occurs in the form of zinc ferrite (franklinite, ZnFe2O4), which is very stable and insoluble in most acidic and alkaline solutions (Langova and Matysek, 2009; Youcai and Stanforth, 2000).Several pyrometallurgical and hydrometallurgical processes (Jankovi et al., 2014; Langova and Matysek, 2010; Morcali et al., 2012; Shawabkeh, 2010) have been proposed for the treatment of zinc ferrites. Pyrometallurgical methods are costly owing to high energy consumption and their emissions of toxic gases are considered an environmental problem; hydrometallurgical methods are preferred for process economy and environmental reasons (Copur et al., 2004)."

Jan 1, 2016

By J. Hadjigeorgiou, G. Knox

There is a considerable wealth of information on the behaviour of rockbolts under axial loading conditions both in situ and under controlled laboratory conditions. However, there is comparably less data on the behaviour of rockbolts in shear. Several authors have contributed to the understanding of the behaviour of conventional rockbolts’ performance under shear loading. Much of this data have been gathered through experimental programmes conducted on sections of the rockbolt. Considering the continuous coupling between the rockbolt and borehole interface, the approach is justified. Due to the design premise of energy-absorbing rockbolts with discrete couplings, full scale testing is required to quantify the behaviour of the rockbolts. This paper reviews published results obtained from two testing facilities, which are the SINTEF rockbolt pull test rig in Trondheim, Norway and the Epiroc Combinations Shear and Tensile test rig in Johannesburg, South Africa, both capable of conducting full scale testing of rockbolts. Based on this high-quality database it was possible to identify three distinct responses of rockbolts in shear. The behaviour under load is controlled by the presence or absence of an encapsulation medium (resin/cement grout), the reinforcement mechanism, and whether the rockbolt is continuously or discretely captured. As a reference the results are compared to the performance in shear of conventional grouted rockbolts.

Nov 24, 2025

By D. Fourie

A brief history of channel sampling in South African gold mines is followed by a chronicle of different sampling events and sampling methods that used the traditional ?hammer and chisel? approach as well as diamond core extraction of the sample. The problems associated with each method of sample collection are documented and the use of a laser scanner to measure the exact volumes of sample material extracted from a correctly delimited sample site are considered. Areas where increment delimitation errors (IDEs), increment extraction errors (IEEs), increment weighting errors (IWEs), and increment preparation errors (IPEs) occur were investigated. A ?simulated chip sample model? is introduced and provides the basis for comparing the percentages of error introduced as a result of improper sampling. The heterogeneity experiment showed that reefs that are more homogenous tend have lower extraction errors than the more complex carbon-rich reefs, which may contribute to understanding the poor mine call factor on mines exploiting the latter types of reef. Keywords channel sampling, chip sampling, error, bias, modelling.

Jan 1, 2014

By J. K. Pothal, S. Basu, R. Barik, P. K. Senapati, A. Dubey

The aim of this paper is to study the characteristics of limestone particles (size varies from 4 mm to 20 mm) during its transportation from open cast mines through pipes. The influence of four different size fractions of limestone samples (4–6 mm, 6–10 mm, 10–15 mm, and 15–20 mm) on pipe flow characteristics during vertical transport in a 100 mm NB hose pipe was investigated. The flow velocities in the vertically lifting pipe was varied from 0.95 m/s to 2.78 m/s and a rotary feeder of 2 to 4 tonne/hr. capacity was employed to feed the limestone samples to the lifting pipe. The pressure drop data for the different size fractions of limestone samples at different mixture velocities were analysed. The effect of input volume fraction and superficial velocity of limestone samples on hold-up ratio were discussed. It was indicated that there was no substantial increase in pressure drop of slurry samples in the studied range of concentrations (CW = 4.22% - 12.54%), particle size, and low to medium range mixture velocities with respect to water run head loss data. The hold-up for the larger size fractions (15–20 mm) of limestone samples was found to be significant as compared to smaller size fractions, which may be due to terminal settling velocities of individual fractions of the studied samples.

Mar 4, 2025

By C. Mueller

Automation of mining operations is pushed by cost pressure and cyclical product prices. However, until now the different types of equipment were not able to communicate electronically with each other or with central computer systems. Therefore, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ‘common electronic language’ for easy and standardized data exchange. As in other industries, this standard is expected to have significant impact on the use of automation in general and on the markets for third party components and software. The standard’s technical architecture is open and flexible for future applications. It consists of an ‘horizontal’ structure defining ‘Application Profiles’ for different types of data sets. An additional ‘vertical’ structure (‘Equipment Profiles’) implements equipment dependent definitions for each of the applicable Application Profiles. First profiles will be available for Drill Rigs. The standard bases on the XML language thus enabling easy data exchange with commercial databases. IREDES data sets may use storage media as well as networking infrastructures for information exchange. The IREDES work is carried out by the initiative members working jointly together in the IREDES work groups. It is open for participation of all interested organizations. First prototyping applications are expected to start during 2001, the first products may be available in the following year. Key words: Mine Automation; Machine Automation; Data Exchange; Rock Excavation; Standard; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Service; Quality Assurance; Control Centre;

Sep 1, 2001

The above paper is an important contribution to the field of physicochemical studies in ferromanganese production. The authors are to be congratulated on the well planned and competently executed experimental work and on the interpretation of the data. Although the paper is essentially descriptive, the results lend themselves to thermodynamic interpretation (but in such a complex system as that studied this cannot be done rigorously), as well as to an examination of the probable reduction mechanisms that operate at various stages.

Jan 1, 1979