Search Documents

By P. Greenfield

The German steelmaking industry has come up with a novel solution to the problem of waste plastics-grind them into particles and use them in the steelmaking process. Plastics make ideal agents for removing oxygen from iron ore in blast furnaces, and save on oil and coal as well. The aim of replacing heavy oil and coal with plastics in blast furnaces is to use them as reducing agents as well as an additional energy source.

Jan 1, 1996

By J. H. van Laar, L. J. van der Walt, P. L. Crouse, H. Bissett, G. J. Puts

"SynopsisSilicon carbide nanopowders were produced using a microwave-induced plasma process operating at 15 kPa absolute and at atmospheric pressure. Methyltrichlorosilane (MTS) served as precursor, due to its advantageous stoichiometric silicon-to-carbon ratio of unity, allowing it to act as both carbon and silicon source. Argon served as carrier gas, and an additional hydrogen feed helped ensure a fully reducing reaction environment. The parameters under investigation were the H2:MTS molar ratio and the total enthalpy. The particle size distribution ranged from 20 nm upwards, as determined by SEM and TEM micrographs. It was found that an increase in enthalpy and a higher H2:MTS ratio resulted in smaller SiC particle sizes. The adhesion of particles was a common occurrence during the process, resulting in larger agglomerate sizes. SiC layers were deposited at 15 kPa with thicknesses ranging from 5.8 to 15 µm.IntroductionIt is well known that methyltrichlorosilane (CH3SiCl3 or MTS) decomposes to form silicon carbide (SiC) and hydrogen chloride (HCl) as shown in Equation [1]. The reaction kinetics and mechanisms for this reaction are thoroughly reported in the literature (Sone et al., 2000; Papasouliotis and Sotirchos, 1999; Kaneko et al., 2002; Wang et al., 2011)."

Jan 1, 2015

By R. T. Tshikhudo

Nanotechnology can provide solutions to many of the world?s socio-economic challenges. The application of nanomaterials for water treatment and analysis, point-of-care diagnostics and targeted drug delivery systems or devices could improve the quality of life for people in developing countries. Gold colloids have a long history (dating back to the 4th century AD) and are particularly well known for their aesthetic appeal and their therapeutic properties. Since Faraday published a report on the synthesis and properties of colloidal gold in 1857, a reasonable insight into the nature of gold sols (nucleation, growth and kinetics of coagulation) has been developed. Considerable attention has been drawn during the past few decades to the development and optimization of methods for the preparation of gold nanoparticles. In nanoscience and nanotechnology today, gold nanomaterials appear to be the most widely used material by both academics and industrialists. This is due to the extraordinary properties of gold nanoparticles (e.g. optical, catalytic, and magnetic?they are also known to act as strong Raman enhancers and may also amplify fluorescence under certain circumstances). Mintek, through Project AuTEK and the DST/Mintek Nanotechnology Innovation Centre (NIC), has been at the forefront of the development of new industrial uses for gold. Mintek?s gold nanotechnology programme focuses on the development of gold-based nanostructured materials and their applications in health, water and other related areas. While few projects use gold nanoparticles for water treatment and analysis, Mintek?s gold nanoparticles are widely used in the health sector. For example, gold nanoparticles are engineered and produced in large quantities as systems for targeted drug delivery. They are also used as tools for advanced rapid diagnostic tests. Both optical and electrochemical rapid diagnostic methods are developed for the human and animal health sectors for point-of-care testing. This paper gives a brief introduction and overview of gold nanotechnology, and desrcibes the development of some of Mintek?s gold nanoparticle targeted drug delivery systems and lateral flow point of care prototype devices.

Jan 1, 2009

By D. W. Horsfall

The coal-preparation techniques used in South Africa over the past ten years are reviewed, the term preparation being taken to refer to processes involving beneficiation techniques. The success of the preparation methods adopted can be gauged from the fact that, although South African coals are generally of a fairly low quality, the country is producing coals both that are used locally for the raising of steam and for metallurgical purposes, and that compete successfully on world export markets.

Jan 1, 1980

By B. M. Munyungano

Rössing Uranium Mine operates a recovery circuit with continuous ion exchange followed by solvent extraction. Serious organic degradation problems were encountered during 1985/6, 2000 and 2005 in the solvent extraction plant. The preferential loss of the tertiary amine extractant was observed during the above-mentioned period. Previous investigations revealed that the tertiary amine was breaking down to nitrosamine, which cannot take part in the exchange reaction with U3O8. A reduction in the redox potential of the solvent extraction plant feed to below 500 mV halted this preferential loss. A lot of effort has been made to try and understand the actual mechanism for nitrosamine formation. Current understanding for the degradation is that formation is due to high nitrates on the strip side of the circuit emanating from nitrates from the precipitation process using ammonia. It is the current belief that pH lower than 3.7 on the strip side results in loading of nitrates onto the solvent. If oxidizing conditions prevail on the extraction side of the solvent extraction circuit, the tertiary alamine will then degrade into nitrosamine. This phenomenon is yet to be established and verified. It has, however, been established that the above process is brought about the following conditions ?High redox potential greater than 550 mV predominately caused by a high Fe3+/Fe2+ratio (4:1) ?Perception that if Fe2+<0.5 g/lit will contribute to high redox ?High concentrations of NO-3 in the conc eluate (feed to SX)/ammonium sulphate (NO-3> 4 g/l based on historic values) ?Presence of Mo as a catalyst ?Tests also have proved that the presence of nitrous acid in a concentration of 1 g/lat 550 mV leads to formation of nitrosamines from alamine.

Jan 1, 2007

By Q. Zhang, X. C. Wang, S. Mao

Phosphate ore is an important strategic mineral resource in which apatite is the main valuable mineral. Flotation is the most commonly used method to separate apatite from middle-low grade phosphate rock. Selective flotation separation is based on the difference of physical and chemical properties of minerals occurring at the three interfaces of mineral/bubble/water. Surface and interface chemistry of mineral have been playing an important role in interpreting and governing its flotation phenomenon. In-situ, visualized and high-precision analytical techniques, such as Time-of-Flight Secondary Ion Mass Spectrometry, Atomic Force Microscopy and Molecular Simulation, have been applied to explore and uncover microscopic nature of apatite flotation. Consequently, a great progress at molecular or atomic level on surface and interface chemistry of apatite flotation has achieved in the past decades. In this paper, the research progress of surface and interface chemistry of apatite flotation such as surface wettability, surface-charging characteristics, surface dissolution behavior, adsorption mechanisms of fatty acid collector and depressor on apatite surface were systematically reviewed. This review will be helpful for the development of more selective reagents and efficient technologies for apatite flotation. Keywords: Apatite, Flotation, Surface and interface chemistry, Surface analysis technology

Jan 1, 2020

By S. Fuchida, Y. O. Zubair, C. Tokoro

Mining of As-bearing minerals had resulted in the release of arsenic species predominantly As(III), which is known to be more toxic, and undue exposure to it is detrimental to human organ systems. Many materials have been examined for As(III) removal, but it is still challenging to advance sustainable materials for effective removal of As(III). In this paper, a more eco-friendly and superparamagnetic Fe0-Fe3O4 composite was synthesised and evaluated for heterogeneous catalytic oxidation and removal of As(III) with peroxymonosulfate (PMS, KHSO5). The kinetic removal studies showed that removal of As(III) was probably through a chemical process and the Elovich model best represented the experimental data. The removal capacity for As(III) on Fe0-Fe3O4 with PMS (1.76 mmol/g) is superior to that without PMS (0.83 mmol/g). Combined results from XPS and ESR showed that As(III) was fully transformed to As(V) through catalytic oxidation by Fe0-Fe3O4/PMS and afterwards enhanced its removal. The removal mechanism of arsenic was ascribed to the formation of outer-sphere (electrostatic attraction) and inner-sphere complexes. The adsorbent can be separated easily from water due to its excellent magnetisation (64.5 emu/g) and also has good reusability potential as more than 85% of the initial concentration of As(III) was immobilised after five consecutive cycles. Keywords: Arsenite, Fe0-Fe3O4 composite, catalytic oxidation, removal mechanism

Jan 1, 2020

By L. A. Cisternas, A. Lopez-Valdivieso, Y. L. Botero, L. Cortes

In the processing of sulfidic ores, pyrite is usually depressed and ends up in the tailings. However, pyrite is the most common species responsible for acid mine drainage (AMD) due to its spontaneous oxidation. This AMD affects the tailing chemical stability by dissolving some toxic or heavy metals species such as As, Cd, Co, Pb, and Zn, which can migrate into the surrounding ecosystems. Therefore, the strategies to reduce pyrite’s environmental impacts are a crucial point to produce more chemically stable tailings. Consequently, numerous studies have been made to find procedures that could inhibit or restrain AMD. This work aims to develop a procedure for designing conceptual flotation circuits that can produce tailings with low content of pyrite and to assess this type of circuit with traditional flotation circuits. The method consists of applying optimal flotation design where three products are considered: metal concentrate, pyrite concentrate, and tailing with low content of pyrite. Two approaches are considered; in the first, a flotation circuit is designed to generate a concentrate rich in all sulfide minerals and to obtain a tail with low pyrite content. Then, a second flotation circuit is designed for the selective separation of the bulk into metal concentrate and pyrite concentrate. This is called fractional separation design. In the second approach, a flotation circuit design is realised that generate the three products simultaneously. This is called integrated separation design. Both fractional separation design and integrated separation design are assessed in this paper. This methodology is focused on cleaner production (waste prevention and resource minimisation) rather than end-of-pipe technology (treat existing waste). The methodology was applied to a copper sulfide ore from a local company in the Antofagasta region (Chile). This ore contains chalcocite, covellite, iron oxides, and pyrite. Keywords: Flotation, tailing, pyrite, cleaner production

Jan 1, 2020

By S. Ramatsoma, D. N. C. Phillpotts, B. Whitehead

Changes in flotation performance have been correlated to changes in froth structure, velocity and stability. Literature has shown that when the aeration rate is varied for a specific float cell, the recovery of the valuable mineral reaches a peak which also coincides with a peak in the air recovery – a measure of froth stability. Peak air recovery optimisation methodology is a way to use direct readings of physical phenomena by froth cameras to optimise the metallurgical performance of a flotation plant. The aim of this paper is to show the transient nature of the peak air recovery value and the variety of conditions required to attain the peak air recovery on an industrial flotation plant with tight base-layer control of the feed and internal conditions. Industrial site tests that were conducted under controlled conditions showed different peak values at significantly different corresponding aeration rates during normal operation. The measured peak air recovery points corresponded to maximum PGM recovery during normal flotation, as expected. This dynamic nature of the peak air recovery point conditions has not previously been discussed in literature and indicates the need for online measuring equipment and informs the design of process control algorithms required to exploit the phenomenon for optimisation. Keywords: Froth flotation, flotation control, flotation optimisation, peak air recovery

Jan 1, 2020

By J. C. Mostert, P. N. Roberts

Electric smelting at Rustenburg Platinum Mines Limited of nickel - copper concentrates containing platinum-group metals By J. C. MOSTERT Pr. Eng.. B.Sc. (Stellenboseh). M.Sc. Met. Eng. (Fellow) and P. N. ROBERTS Pr. Eng.. B.Sc. Eng. (Rand) (Fellow) The processes involved in the smelting in an electric furnace of nickel-copper concentrates containing platinumgroup metals are described. These are concentrate drying, pelletizing, pellet drying, and flux and pellets proportioning, followed by smelting of the concentrate in a submersible-electrode electric furnace, which is discussed in more detail. The furnace matte is blown in a converter to the white-metal stage and is cast in moulds, whilst the slag is granulated, ground, and floated for recovery of valuable metals and afterwards pumped to the tailing dam.

By J. Petersen, H. Naderi, H. Zare, M. H. Nikzad, M. Karimi

In the copper electrorefining process, the dissolution of anodes is significantly reduced or even stopped when the passivation phenomenon occurs. The results of this phenomenon are increasing energy consumption, residual formatting, and voltage levels in the cell. In this study, the electrochemical behaviour of blister copper in the presence of sodium persulfate (PDS) was studied. The electrochemical methods of LPR, Tafel, and Electrochemical Impedance Spectroscopy (EIS) were used. The results showed that the addition of sodium persulfate activates the electrode surface and increases the open circuit potential. In the presence of PDS, the polarisation resistance of the electrode shows an increasing or decreasing tendency, based on the PDS concentration. This tendency is probably due to the formation of surface layers (such as slime layer or copper sulfate) and dissolution of this layer at various concentrations of PDS. The lowest polarisation resistance of 1.8 ohms and the highest corrosion current of 60.6×10-3 and 36.6×10-3 A/cm2 from LPR and Tafel techniques respectively were obtained at the concentration of 40 g/l PDS. Based on the results of potentiodynamic and electrochemical impedance spectroscopy tests, the addition of sodium persulfate to the solution reduces the corrosion resistance, therefore the passivation time of the blister copper anode increases. Keywords: Blister copper, electrorefining, sodium persulfate, anodic passivation

Jan 1, 2020

By W. F. A. T. Meihack

The scope of this paper is confined to gas-fluidized beds in pyrometalurgical applications. After considering the general characteristics of these fluidized beds, the author deals with their potential applications, using the following processes, which are currently under investigation, as examples: pretreatment of chromite, prereduction of manganese-ore and iron-ore fines, roasting and prereduction of ilmenite, and roasting and pyrolysis of gold-bearing pyrite. He concludes that fluidized beds are potentially of great benefit to the metallurgical industry, although much developmental work remains to be done.

Jan 1, 1986

1. Books from Elsevier The folowing are available from Elsevier Applied Science, Crown House, Linton Road, Barking, Essex IGl 8JO, OK. . Driling wastes, edited by F.R. Engelhardt, J.P. Ray, and A.H. Gilam. 1989. 872 pp. £95. Geothermal resources, by R. Bowen. 2nd ed. 1989. 468 pp. £60. The fate and efects of oil in freshwater, edited by J. Green and M.W. Tret. 1989. 340 pp. £42. Mining and the freshwater environment, by Martyn Kely (with contributions by W.J. Alison, A.R. Garman, and C.J. Symon). 1988. 228 pp. £32. 2. Books produced by Metal Buletin The folowing are available from Metal Buletin PLC, Park House, Park Terace, Worcester Park, Surey KT47HY, England. Prices and data 1990. £41 (airmail). Foundry directory and register of forges 1989-1990. £52 (airmail). 2. Canadian Publications The folowing two publications are available from the Canadian Government Publishing Centre, Supply and Services Canada, Otawa, Canada KIA 059. Mining and mineral processing operations in Canada. Mineral Buletin MR 224. $23.70. Canadian minerals yearbook 1989. Review and outlook. Mineral Report 38. $47.95. Technology developments The Mintek Pyrosim Simulator Pyrosim is a computer program for the steady-state simulation of pyrometalurgical processes?.

Jan 1, 1990

By L. Morin, S. Mortazavi, K. Volchek, A. Demers, A. Di Feo

The objective of this paper was to investigate the possibility of reducing process (fresh) water and increasing recycled water (thickener tank overflow water). As part of the investigation, rougher flotation tests were done with the two water types and a mixture of the two (50%/50%). The effect of recycled water on the grade-recovery response and rougher recoveries was investigated. When thickener tank overflow was used (50% and 100%), the nickel+copper grade versus nickel recovery decreased. The decrease in the grade-recovery was due to higher pyrrhotite recovery. Also, there were no effects on nickel and copper recoveries, which was confirmed using multivariate statistical analysis at the 95% significance level. Keywords: Flotation, nickel, copper, water recycling, multivariate statistical analysis, MANOVA, reverse osmosis

Jan 1, 2020

By L. Forbes, G. Forbes, J. Wang

Bubble size measurement is a vital part of flotation system analysis and diagnostics. Over the years, a great many different bubble size analysis tools have been developed. However, all of them rely on ex-situ measurement and in-pulp sampling techniques. This paper evaluates the Mettler Toledo ParticleView™ Measurement probe as a novel method for in-situ bubble size measurement. This device is then compared to the conventional Anglo Platinum Bubble Sizer (StoneThree). It was found that the in-situ bubble size analysis technology appears to be a more user-friendly and reliable option for determining bubble size in flotation. However, the current instrument design is not suited to industrial applications. Keywords: Bubble size measurement, bubble coalescence, PVM probe

Jan 1, 2020

By F. Diot, S. K. Tripathy, L. O. Filippov, I. Filippova

Among different pre-treatment methods, a high voltage electric pulse was recently developed and is gaining popularity due to multi-benefits such as pre-weakening along the grain boundaries, as well as size reduction to improve the liberation characteristics. In this paper, the pre-treatment using high voltage electric pulse of lithium-bearing granite ore was studied to understand the morphology through texture, as well as the friability of the particles. To understand the phenomena, SELFRAG, a laboratory facility used for generating high voltage electric pulse and key operating variables were varied. The role of applied voltage (94.5-195.5 kV), number pulse (3-87), and the frequency of pulse (1.3-4.7 Hz) was varied to understand the liberation characteristics as well as energy consumption. Characterisation tools such as optical, and electron microscopy were used to describe the pre-weakening phenomena through textural features. Further, the energy required to break the particle to finer sizes as well as friability were determined and described. Keywords: Pre-treatment, high voltage electric pulse, lithium, liberation, grinding

Jan 1, 2020

By B. Kenealy

A typical deep shaft is President Steyn No. 2 in the Free State, where 9 tonnes of ore are hoisted at about 15 metres per second from 2378 metres below surface. The skips and attachments each weigh 7 tonnes and they are connected by 43 tonnes of rope, so that to hoist the 9 tonnes of payload, a total of 66 tonnes is accelerated from stand still to 55 km/h for each cycle, using an average of 3185 kilowatts of power in the process. The cycle time for the hoisting is 3.22 minutes. The peak power consumption is 6954 kilowatts, which determines the size of the motor used. Is this the right approach? Are larger skips moving at higher speeds the answer? Is there another way?

Jan 1, 1996

By P. G. Toledo, R. I. Jeldres, G. R. Quezada

Chile is the main producer of copper in the world and lately the mining industry has suffered challenges due to the lack of water in the north of the country, along with the new policies of not using fresh water for the industry. This has prompted the use of seawater as an alternative source for mining. Several studies have been driven due to this new scenario, which have shown that seawater can be beneficial, if certain ions are removed from the process. This is the Mg that generates precipitates at high pH, that have been shown to make mining operations difficult. In particular, thickening operations are impaired by the presence of Mg ions, where aggregate formation and sedimentation decreases substantially. Our studies suggest the competence of the precipitates in adhering to the polyacrylamide (HPAM) flocculant and not towards the surface of the quartz minerals. This motivates the present work to use molecular dynamics to study the adsorption of a HPAM molecule on quartz surfaces and the surfaces formed by Mg precipitates. The surfaces are immersed in a saline solution or seawater that includes the HPAM molecule. Results are obtained by measure the adsorption frequency and duration. We obtained that the HPAM molecules are preferably absorbed on the surfaces of magnesium hydroxide. This gives us a good agreement with what is observed experimentally and strengthens the premise of the competition of hydroxide with the flocculant. Keywords: Molecular dynamics, adsorption, tailing flocculation, magnesium removal

Jan 1, 2020

By Y. J. F. Haven, G. H. J. Kitson, D. G. Beadle

I have read this paper with considerable interest. By using an automatic instrument to assess the dust samples taken in South African collieries, the authors are ahead of the gold mining industry, which still uses the laborious method of microscopic assessment, with its limited accuracy, of the half-a-million dust samples taken each year. As the authors state, the result obtained from the photoelectric assessment of the samples is approximately proportional to the surface area of the respirable dust. However, modern theory is that, in assessing coal dust, it is the respirable mass which is important in determining the danger to health. Thus Table II of their paper is of considerable value in showing the relationship between the P.E.R. value and the mass concentration measurement. Unfortunately this table only gives the mean relationship. The important point is to know the scatter around this mean. If the scatter is small, then this mean value (for different operations) would have considerable value in converting from respirable surface area to respirable mass, but if the scatter is large, then such a conversion, using a fixed factor, will have little value. In the text the authors mention the range of values as being between 3 to 24, but without a statement on the number of samples used to determine this range and their distribution, this is a rather nebulous statement. I hope, in their reply, that the authors will give, in statistical terms, some statement on the overall correlation between these two parameters. I might add that at present a member of my staff is working on similar relationships for dust samples taken in gold mines. Another factor which may well be most important in determining the danger of dust levels in coal mines is the composition of the dust, specifically its quartz content. I understand that the authors have some information on this point, and to make their results of greater value in International comparisons of dust levels and the concomitant development of pneumoconiosis, it will be extremely useful if they could place this information on record. Even though, as I have said above, modern theory postulates that respirable mass is a better parameter to use than respirable surface area, the problem remains of how to measure this parameter with short time sampling, which, as the authors point out, is their preferred strategy for dust sampling and dust control. I know of no easily portable instrument, independent of external power supplies, which can, in 5 to 10 minutes, collect sufficient dust to enable it to be weighed accurately. Thus the authors&apos; implied intention of continuing to sample by their present techniques and using their present parameter to report the results is, in my opinion, an entirely valid decision.

Jan 10, 1968

By J. Güntner

Most copper/cobalt ores from the Central African Copperbelt contain sulphidic compounds, which are not extractable in direct leaching. Roasting provides the possibility to transfer the valuable components into leachable compounds. In an operation window defined by temperature and off-gas composition it is possible to selectively oxidize iron sulphides to haematite and copper/cobalt sulphides to sulphates. Selective sulphating of the valuable minerals is an important condition for the subsequent leaching stage. The dissolved copper and cobalt are recovered by solvent extraction and electrowinning. This technology has been part of an established process for many decades. The concentrates from recent projects on the Copperbelt have lower sulphur contents, and frequently higher copper contents, than those from older projects. The paper shows the consequences of this trend for plant operation and explains useful counter actions by means of case studies. Autothermal combustion is ensured even at very low sulphur contents. Off-gas treatment has so far been based on SO2 removal through sulphuric acid production. The generated acid is used to make up acid losses in the hydrometallurgical plant section. This well-proven process combination is still the preferred route if the feed sulphur content is high enough; however, some cases may require different off-gas cleaning concepts without compromising on clean air quality. Roasting in a fluid-bed furnace remains the core of the technology. Fluid-bed roasters are easy to operate and provide an excellent control of the calcine quality. Different feeding and heat-recovery systems are used to provide a tailor-made solution for each project. Outotec built it first sulphatizing roaster in Zambia about 30 years ago. At that time, the roasting of metal sulphides was already one of the main technologies in the company. Outotec has developed roasting solutions for copper, gold, zinc, lead, molybdenum, and pyrite ores. The continuously expanded and upgraded research facilities provide an excellent basis for developing sustainable, energy-efficient, and economic solutions for copper and cobalt production in Africa.

Jan 1, 2012