Search Documents

By Gordon F. Revey

In underground construction and mining work, situations occasionally occur where hard rock or concrete must be excavated at locations near critical structures or utilities. Fearing damage from blasting, contractors and engineers often explore the viability of using mechanical methods or expansive concrete to facilitate the excavation work. However, for moderate to large excavations, the prolonged duration and high cost of using these methods is often impractical. In these situations, under the right conditions, controlled blasting and blast-management methods can be used to speedup the work and lessen costs. The process of determining whether or not blasting is practical is often complex, particularly when risks are high. In this paper, general methods of conducting blasting risk evaluations and outlined and considerations for blast design and risk management are reviewed. This paper also includes three blasting case histories demonstrating how these techniques were used at recent projects. In the first case, a cautious blasting program was developed to facilitate the removal of concrete and rock within a large section of an active mineshaft. The second case involved critical blasting to excavate a dry lake-tap connection between a tunnel and a shaft at the Southern Nevada Water Intake No. 2 project in Henderson, Nevada. The third case history describes how novel blasting methods were used to carefully drop a 2,721,500-kg (6,000,000-lb) concrete caisson into a1.2-m (4-ft) rock socket at the Detroit Outfall No. 2 project in Detroit, MI.

Jan 1, 2001

By J. P. Ulery

As a result of several recent methane/dust ignitions in surface auger and highwall mines, the U.S. Bureau of Mines investigated the occurrence of methane gas at these operations. Three mine sites were visited in western Kentucky and one in western Pennsylvania to collect run-of-mine coal samples for gas content determination using the modified-direct-method (MOM). Results indicate the samples emitted small quantities of methane, carbon dioxide, and nitrogen. Either methane or nitrogen was the predominant gas released. The same gases were released after crushing the samples for residual gas content; however, nitrogen was the primary component of this fraction. Total ~as contents ranged from less than 0.01 cm /g to 0.54 cm3/g. The hydrocarbon gases probably originated during coalification. Other gases may have originated partially as a byproduct of coalification and partially as a result of other, near-surface processes. The data suggest that although methane quantities are small, desorption could occur at near surface conditions prior to mining. The desorbed methane could accumulate as a free gas in fractures in the coal bed or roof rock. When these fractures are penetrated by the auger, methane could rapidly enter the whole atmosphere possibly creating explosive conditions.

Jan 1, 1994

By James C. Gilliand

Leo-potpourri, was selected as the title to this paper for several reasons. First, it is a fascinating word--not looking like it sounds or sounding like it looks. It also allows for a great degree of flexibility in designing a presentation around it. Further, it has become popular to use this eco hyphen something pattern. We hear of eco-mania, eco-hysteria and the like. Lastly, in this era of intense environmental concern, two of the principle elements on which the integrity of our efforts must be equated are ecology and economics. Accordingly, the term "Eco-potpourris" allows me to roam at will through the great number of considerations that make up this environmental issue. Whereas only a few years ago the subject of environment and environmental control had low visibility with the public, today it competes as the focus of attention with the many other popular social issues of our time. The program content here at this meeting, for example, is liberally represented by papers dealing with one or more aspects of environmental concern. If one would look at the 1964 program, in contrast, I would expect that no more than possibly one or two papers covered this subject and even then that those papers dealt principally with the environmental aspect of occupational health. It is gratifying that the program at this meeting demonstrates a serious awareness to a broad spectrum of environmental concerns. It would be a mistake, of course, to believe that this clamor for a quality environment is a "flash in the pan" that will soon subside. The general public has been thoroughly aroused and even frightened into

Jan 1, 1972

By James E. Friant

The technology applied to shaft sinking has lagged far behind other construction activities. While surface oriented construction and mining have made great strides with new processes and equipment, the majority of shafts sunk currently still follow a drill, blast and muck-out cycle developed in the 16th century. Today, in 1979, the shaft sinking industry is in the midst of its own private industrial revolution. Millions of dollars are being spent annually by industry and government alike to spring the art of shaft sinking into the 20th century. The objective of this paper is to review a few of the newest mechanized schemes for shaft sinking. This is not a theoretical review, however, but a practical one, and deals only with hardware and projects which are currently on jobsites. Figure 1 shows the equipment. On the left is the 241SB 184, a 24 foot diameter blind shaft borer. This machine is currently at about 200 feet, constructing a coal mine shaft in Alabama. It is built and utilized in a manner similar to a tunnel borer. In the upper center is the 1211SR, a 12 foot diameter blind shaft reamer. This machine follows a 6 foot pre-drilled blind pilot hole, and is at work in Chicago. On the upper right is the 121BR, a powerful new blind drill. Just below it is the conical drill head for the 121BR which can utilize either carbide or standard disc cutters. At the center bottom is an expandable back reaming head which can be used to enlarge a drilled shaft up to a maximum of 16 feet diameter, or can be used to produce a shaft having several diameter changes. This equipment is also in use in Chicago.

Jan 1, 1979

By D. Diekman

Perlite is not a trade name but a generic term for naturally occurring siliceous volcanic rock. A distinguishing feature which sets perlite apart from other volcanic glasses is that when heated to a suitable point in its softening range, it expands 5 to 20 times its original volume. This expansion is due to the presence of 2% to 6% combined water in the crude perlite rock. When quickly heated above 1600°F (871°C) crude perlite pops in a manner similar to popcorn. The combined water vaporizes and creates countless tiny bubbles in the heat softened glassy particles. It is these tiny glass sealed bubbles which account for the amazing lightweight and other exceptional physical properties of expanded perlite. The bulk densities of the expanded perlite generally range from 3 pounds per cubic foot (48 Kg M3) to 10 pounds per cubic foot (160 Kg H3).

Jan 1, 1985

By S. Donges, P. L. Dunstan, B. J. Huls

The commissioning of a distributed digital control system for the grinding circuit at Cuajone was completed by mid-August 1985. Development of a successful strategy, excellent operator acceptability, and the visual aspects offered by the display of the central console improved mill through- put significantly. The inherent features of a digital system enhanced the flexibility in grinding control and allowed the milk and classifiers to be operated at maximum capacity. This paper discusses the strategy development and the production restrictions encountered, and evaluates the overall performance of the digital control system.

Jan 1, 1988

The Xinglongzhuang Coal preparation plant project was a joint effort by American and Chinese engineers and for the most part designed to American standards. The plant owner and operator is the Yanzhou Coal Mine Administration, a division of the Shandong Coal Corporation. These are state owned companies which ultimately fall under the Ministry of Coal in Beijing. The new 3.0 million ton per year Xinglongzhuang mine is located in southern Shandong province in east-central China about mid-way between Beijing and Shanghai. This is an agriculture area, flat terrain, relatively dry climate with temperatures similar to Western Kentucky. During Confucius time (551-479 B.C.) this area was known as the state of Lu. Confucius home town of Qufu is about 20 kilometers to the north-east of the mine site.

Jan 1, 1989

By A. V. Castelli

Weighting materials as we know them today were first recognized in 1922 by B. K. Stroud1. Stroud, who was supervisor or the Mineral Division of the Louisiana Department of Conservation, tested galena, cement and hematite as weighting materials and successfully used hematite to make a "heavy mud". The first use of barite was in the fall of 19222 . The process of adding heavy minerals in mud was patented in 1926 by Stroud and National Pigments and Chemical Company, a subsidiary of National Lead Company now NL Industries, Inc. The ground barite was marketed as BAROIDR barite.

Jan 1, 1983

By K. G. Thomas

New developments in gold exploitation over the past few decades have been extensive and promise to be exciting for the foreseeable future. They cover all phases of gold mining from developments in mining, processing, computer and finance. This presentation will cover these different disciplines and show how Barrick Gold Corporation ("Barrick") has used these devel­opments to enhance shareholder wealth. The developments can be grouped into disciplines as shown in the following table.

Jan 1, 1996

By John G. Groppo, Bonnie Webb-Groppo

INTRODUCTION The first portion of this chapter is concerned primarily with the contamination aspects of fine coal cleaning that include both the solids and water discharged as waste products after coal preparation. Topics include characteristics of the water and solids, changes that occur to both of these phases during use and after impoundment, as well as the impact that these changes have on unit operations and the environment. Attention is also given to the formation of acid mine drainage and treatment options that may facilitate reuse of the water. The second part of the chapter analyzes the problem of air contaminants from coal preparation plants including analysis of air pollutants and control methods. An overview of air quality regulations is also presented; most provisions have little or no applicability to coal preparation plant operation but are presented to provide an understanding of end-user constraints. The final part of the chapter emphasizes the long-range problem of refuse disposal and control. An overview of characterization, maintenance, and control of the refuse area is presented, as well as design guidelines. A brief review of stability analysis procedures is also included. PREPARATION PLANT WATER Characteristics of Makeup Water for Coal Preparation There are few specific rules governing the quality of makeup water used in coal preparation processes.'" It is generally accepted, however, that the solid matter content should be less than 5%. The solids concentration in plant makeup water typically varies between 0.25 to 0.9 lb per gal (30 to 110 g/L) and may reach concentrations as high as 1.7 lb per gal (200 g/L). The water used in coal preparation is usually obtained from one or more of the following sources: public supplies, rivers and streams, canals, mine water, and wells. In most cases, water is obtained at the lowest cost including any necessary treatment. A major portion of the recirculated water is clarified by thickeners and settling ponds to remove fine coal and clay particles. Sufficient water is generally available to meet the needs of coal preparation in most areas. It has been estimated that approximately 65 to 70% of the makeup water used in a coal preparation plant comes from surface sources. It is important to note that a variety of substances are commonly found in natural water supplies, whatever the available source may be (Table 11-1). Excessive concentrations of some of those substances can have an affect on plant performance; the effect of specific contaminants on unit operations will be discussed

Jan 1, 1991

By A. T. Weber, G. T. Adel

Earlier studies on the hydrodynamic interactions between fine particles and air bubbles have shown that fine particle flotation can be improved by using small air bubbles. In the present work, microbubbles ranging in size from 70 to 250 microns have been used in a flotation column for the processing of fine coal. The performance of the microbubble column has been studied as a function of wash water addition rate, aeration rate, feed rate and column length to diameter (L/D) ratio. The information collected from these tests has been used to analyze column behavior and to develop scale-up criteria. The results of this investigation suggest that mixing within the column may not be as significant as bubble size and residence time in determining column performance. Improved recovery can be obtained by decreasing bubble size which increases the flotation rate constant, and also by increasing L/D which increases residence time for a fixed column volume. The increase in residence time with L/D is due to a decrease in the volumetric flow rate of wash water with column diameter.

Jan 1, 1988

By Ronald I. Fuller

Core Laboratories, a division of Western Atlas International, maintains laboratories in all energy-producing areas of the United States, as well as in many foreign countries. Central to laboratory operations has been the incorporation of computers and computer software. Core has developed a mu1tiuser Laboratory Information Management System (LIMS) , which is currently installed in numerous company sites in the U.S., and is now undergoing installation in Canada. In addition, Core has provided custom soft ware to contract laboratories which Core operates on behalf of mining firms. The software development was done under the direction of the author in Denver, Colorado, and Casper, Wyoming. The intent of this paper is to pass some of the practical experience gained by our efforts on to those who wish to utilize computers more fully in the laboratory setting. The product of analytical laboratories is numbers. Nothing else comes from our work. We deal in information about samples. It is then reasonable to assume that the computer would be central to a laboratory operation. The hard part is to initially define what kind of computer the lab operation needs. The choices today can be very complex, and almost every hardware salesman is full of bad advice. Even the people in your own information services department may hold divided opinions. Since the advent of the personal computer, we have lived with a polarized data processing community. The PC boys consider their machines equal to any challenge, while the "save the mainframe" crowd view the PCs as limited toys that are only good for the things that clutter up a real computer. Management tends to lean toward whatever costs the least.

Jan 1, 1989

By Joseph Cervik, Fred Garcia

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of the discharge pipe. These measurements are erroneous and tend to be high by as much as 30%. The Bureau of Mines determined correction factors (method factors) for anemometer measurements taken in this manner. Method factors for 10.2, 15.2, and 20.3 cm (4, 6, and 8 in) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By Charles T. Ford

Limestone neutralization of acid mine drainage has been proposed and examined as a method of treatment. However, limestones differ greatly in composition and structure. The reactivity of 14 selected limestones was studied, both by chemical and physical properties and by relative effectiveness in neutralizing synthetic and actual mine waters, and several guidelines for the choice of limestones are given. The particle size should be at least as small as 74 microns and preferably smaller. The most effective limestones are most nearly pure calcium carbonate. Stones which have a relatively low calcium con- tent but which contain calcite and have a large surface area are also effective neutralizers. Magnesite and dolomitic limestones are much less reactive. Disadvantages in using even the most reactive lime- stones for neutralization are indicated.

Jan 1, 1974

By John G. Myers, William A. Vogely, Harold J. Barnett

INTRODUCTION, CONCEPTS, AND MEASUREMENT Introduction Periods in the history of man, from his earliest appearance to the present, are often characterized by the principal materials used. In nearly all cases, the material or fuel is of mineral origin-stone, copper, bronze, iron, coal, and so forth-indicating the principal ingredient of the tools or source of power of the period. Each of these periods represented great improvement over the preceding one in terms of human well-being, as measured by population growth and other indicators (Cipolla, 1978). A major reason for the improvements in production and well-being was the nature of the material or fuel, each successively superior to the preceding, which made it possible to produce more food, fuel, shelter, and clothing with a given amount of labor. If we accept this well-documented description of economic progress as accurate, we may then turn to the consideration of two related questions concerning this development. The first, easily answered,-is why man spent long periods of time (millenia, in many cases) making tools from inferior materials, such as copper, instead of passing directly to superior materials, such as iron and steel. The second, closely related question, concerns the relation between the rate of economic growth and the quantity of mineral reserves available at any time. For the first question, the answer is that the technology required to discover, extract, and process each successive material had to be discovered and developed before the material could be used. Once the technology was available, the new material could be and was exploited widely, raising productivity-output per unit of labor- and consequent consumption per person. This familiar idea underlies a fundamental principle of the economics of resources, namely, at any time, available resources depend upon available technology. No mineral or other raw material is a resource unless the technology has been developed to utilize it. But once the technology is at hand, the new resources associated with it provide the means for economic growth and rising levels of living. This principle is subject to certain conditions. For example, governments or other institutions may prevent a mineral from being used, even though the technology is available. And, if a mineral is located in a remote place, transportation charges may make it uneconomic to exploit. Such minor qualifications do not, however, change the thrust of the argument that technology is the overriding determinant. With respect to the second question, it might seem apparent that the greater the quantity of reserves available, up to some point, the more economic growth will be facilitated. This line of reasoning leads to the conclusion that as re- serves are consumed the quantity available will be reduced and economic growth will eventually be restrained. Reasoning of this sort underlies much popular (and scholarly) thought, in which depletion of mineral and other resources is assumed to lead to constraints on economic growth, through higher materials costs and absolute limitations on materials use. Two important qualifications must be made to this explanation, however, which together

Jan 1, 1985

By Charles W. Daugherty, Eugene B. Waggoner

In the construction of recent subsurface projects, particularly mined openings and transit systems, it has been apparent that final costs were often greater than first expected. Because many overruns result from alleged differing site conditions, there was reason to suspect that pre-bid geotechnical investigations were inadequate for predicting subsurface geology. In 1982, nine federal agencies involved in constructing underground facilities funded the National Academy of Sciences' U.S. National Committee on Tunneling Technology (USNC/TT) in an effort to evaluate and clarify the relationship between geological knowledge and construction costs. That committee formed the special Subcommittee on Geological Site Investigations, which spent more than two years studying underground projects by examining contract documents and geologic reports, making site visits, and interviewing owners, designers and contractors. The study ultimately encompassed 84 mined tunnels and chambers and three deep shafts in the United States and eastern Canada. Data collected on geologic exploration, design and construction were analyzed and conclusions reached concerning whether and how site investigations need to be improved. The results of the study are published in two volumes by the National Academy of Sciences. Due to the recent completion date of the main report, it was not possible to prepare a summary for inclusion in the RETC Proceedings. However, the complete two-volume report, "Geotechnical Site Investigations for Underground Projects," can be obtained by writing or calling: U.S. National Committee on Tunneling Technology National Academy of Sciences 2101 Constitution Avenue, N.W. Washington, D.C. 20418 (202) 334-3136

Jan 1, 1985

By James R. Aggson, Verne E. Hooker

GENERAL CONSIDERATIONS The design of a mine or any underground opening in rock is similar to the design of any other structure, such as a building or a bridge, in one important way. This similarity lies in the fact that the stability of the structure is a function of the loads that will be applied during the structure's expected lifetime. In the case of an underground opening, the applied load is the product of the existing in situ stress field and the concentration of this field that is produced by the extraction of a load¬bearing material. Thus, a knowledge of the in situ stress field is considered a basic requirement in the design process and essential to the eventual stability of the underground structure (Duvall, 1976; Obert, 1972; Merrill and Peterson, 1961; Dahl and von Schonfeldt, 1976; Hedley and Wilson, 1975). The in situ stress field can be used along with the physical properties of the rock masses involved, the ge¬ometry of the various rock types, the geometry of the openings involved, and a failure criterion to evaluate structural stability of a planned mine by theoretical or numerical techniques. This same information can be used to investigate ground control problems in existing mines. In situ rock stress determinations can be separated into three categories: the determination of applied stress, also called the absolute or field stress; the deter¬mination of concentrations of the field stress near open¬ ings; and the determination of changes in rock stress as load-bearing material is removed. The applied stress field is more difficult to determine than are stress changes. Various instruments and techniques have been developed to determine applied rock stress and stress changes in rock. ABSOLUTE OR FIELD STRESSES Theoretical Considerations In the absence of actual measurements, it is often assumed that at any point, the vertical stress is equal to the weight of the overlying material. [ ] where S„ is vertical stress, S is average weight density of overburden rock, and h is depth from the surface. This is normally consistent with actual experience. The horizontal stresses are assumed to be equal and related to the vertical stress through the Poisson effect. [] where Sh is horizontal stress, S„ is vertical stress, and v is Poisson's ratio. The derivation of Eq. 2 is dependent on lateral con¬finement of the rock mass. An increasing amount of information is rapidly becoming available which indi¬cates that the in situ stress field at a particular location cannot simply be assumed to be a gravity-induced stress distribution in which the secondary principal stresses in the horizontal plane are due to confinement and Pois¬son's effect. Rather they can be a complex function of gravity loading, regional stresses, structural features, ex¬cavation geometries, and variations in surface and/or possibly basement rock topography. Furthermore, the underground principal stress dis¬tribution is not necessarily vertical and horizontal as is often assumed. The deviation of the three-dimensional stress distribution from vertical and horizontal can be due to a combination of both topographic (Hooker, Bickel, and Aggson, 1972) and structural features.

Jan 1, 1982

By Robert F. Randolph

New technologies confront mining organizations with unprecedented human factors challenges. Likely problem areas range from the design of the human- machine interface to the design of work groups and mine organizational structures. However, these human design considerations are commonly ignored in most industries, resulting in a failure rate of 75% for advanced technology programs. The U.S. Bureau of Mines is addressing these concerns through a program of research on the human side of high technology mining systems. Interviews with mining industry participants and researchers have identified concern in several areas, including training and equipment design. Although new mining technologies promise to improve overall safety by relocating miners away from hazardous areas, data from MHSA accident reports and other sources suggest that certain types of new hazards may be created. Many of these new hazards can be reduced though a systems approach to ergonomic design of equipment, tasks, and work processes. This evidence, combined with reviews of high technology human-machine systems in other industries. can help in the design of safe and efficient future mining technologies.

Jan 1, 1992

By Jan Leja

Surfaces of metal sulfides react readily with selected constituents of environment. Two types of reaction products may form: (1) primary, chemisorbed and hydrophobic surface products or primary hydrophilic surface products, and (2) secondary reaction products -- produced during continued oxidation-reduction processes. For flotation, the chemisorbed surface product and the secondary reaction products, elemental sulfur or metal xanthates, must provide sufficient hydrophobicity of the surface to ensure particle-bubble attachment.

Jan 1, 1986

By Peter J. Szabo

Introduction There has been much said recently about the sophistication of Japanese management in turning out reliable, inexpensive products, such as cars and steel. Techniques include consensus management and quality control circles. These have been touted as prime reasons for inexpensive Japanese products. An often neglected, but major factor in the equation of cheap export goods is the role played by Japanese trading companies. These venerable institutions are a vital factor in Japan's overall strategy of keeping the price of raw materials at the absolute lowest levels. This is critical to the country's economy since the nation must import more than 85% of all its coal. A country that is so desperate for imported raw materials would appear, at first glance, to be at the mercy of its suppliers. In Japan's case, however, the opposite is true. With the exception of brief' windows in 1974-75 and 1980-81, Japan has been in the driver's seat in negotiating contract terms. Due to its dominant role in world coal trade, Japan's situation can be described as a de facto monopsony. By definition, a monopsony is a market situation where the product, in this case coal, is offered by many sellers, but is sought by one buyer. This has been due to the role of Japanese trading companies in dealing with suppliers. Table I depicts trading companies by size in 1982. Mitsubishi and Mitsui are overshadowing in terms of size. The others, though less significant, play a vital role in orchestrating the marketplace. Three critical building blocks on which the strategy of the trading companies are based include intelligence networks, exceptional training of company traders, and shrewd contract negotiation practices. Intelligence Networks All success is derived from these three key components. Of the three blocks, intelligence gathering is the most important. With all the sophistication of the Central Intelligence Agency, the Federal Bureau of Investigation, Interpol, and the Surete', the Japanese trading company's method is every bit as competent and far more gentlemanly. Friendly competition is the key to survival. Although one Japanese trading company appears to be in ardent competition with its rival Japanese trading companies, when studied closely, a totally different picture emerges. The end user nominates certain trading companies as market channels and informally guarantees they will receive compensation regardless of which company wins a specific order. With this concept in mind, the pressure is off. The trading company can aim at getting the best price for the end user. Therefore, bargain, beat, and share information. Do whatever is necessary, but get the lowest price for the end user. Even with the game so gentlemanly, no victory could be assured without an adequate intelligence network. Proper intelligence is only as good as the sources drawn from. But how is one assured of getting the right information? The answer is verification. Verification is comprised of numerous independent sources each cross checked at a central processing unit in Tokyo. Each major Japanese trading company receives input, not only from its own trader, but from other trading companies as well. In addition to their own compilation, trading companies rely on the The Coal Manual, published annually in Tokyo by TEX. This manual covers every major coal producing country. Mines are located and seams identified, mining recovery, equipment lists, washing yield, railway distances

Jan 1, 1985