Search Documents

By Dennis V. D’Andrea, Peter G. Chamberlain, James J. Olson, William C. Larson

Blasts designed for in situ copper leaching must produce adequate fragmentation and permeability for successful leaching. Copper recovery depends to a large extent on the particle size distribution created by the blast, the permeability in the blast- fractured zone, and the ability to maintain solution flow with a minimum amount of channeling. This paper presents the results of Bureau of Mines experiments where core drilling was used before and after blasting to establish the degree of fragmentation. Data are presented from tests at the Sierrita mine of Duval Corp., and also from tests at the Emerald Isle mine of El Paso Mining and Milling Co. Copper recovery is predicted from fragment size distribution data using a computer model. Data from several blasts are used to show how predicted copper recovery is related to powder factor.

Jan 1, 1977

By Eric Gilmore, Ron Tudor, Gregory E. Korbin, Bill McCormick, Brad Bush

INTRODUCTION Las Vegas has recently been termed the “Construction Capital of the Country”. It has also been acknowledged as the fastest growing city in the country for several years running. The rapid growth improves the economic picture of the region but it also imparts unusual demands on the area’s infrastructure. In 1994 the Southern Nevada Water Authority (SNWA)was working on a master plan to address the rapid growth. A long range analysis revealed the need for additional water treatment capacity and delivery systems. Short term projections showed that the current system would reach capacity in the summer of 1997 with the possibility of demand exceeding the supply. The River Mountains Tunnel #2 is part of a $150M scheme to quickly upgrade the system to meet the short term demand, improve the overall system operation and allow for a smooth transition into the larger additions being planned for the future. The SNWA selected Carollo/Black & Veatch (CBV) to provide detailed design and construction management for the upgrades. The River Mountains Contracts consisted of five separate contracts broken out separately to stream line a very aggressive (just 34 months) design and construction schedule. Necessary work included four miles of excavated and lined tunnel, connections from existing pipelines to and from the new tunnel including large diameter (to 3.66m(144 in)) valves, a 18 927cu m (5 million gal) regulating reservoir, a surge tank and a 170 343cu m (45 million gal) reservoir to add additional storage to the system. Notice to Proceed was given to Kajima Engineering and Construction (Kajima) on May22, 1995 for the construction of the River Mountains Tunnel #2. The design called for a tunnel to be driven 6070m (19 915ft) in rock and lined to a finished diameter of 3.71m (12.17ft).Excavation began on December 14, 1995 and holed through on April 30, 1996. Lining began on June 25, 1996 and a notice of Substantial Completion was issued on December 13,1996. This paper describes the measures taken to complete the tunnel in 18 months from Notice to Proceed to Substantial Completion. THE RIVER MOUNTAINS SITE The River Mountains are a low range of rugged mountains separating the Las Vegas Valley from its main supply of water, the Colorado River at Lake Mead. They are volcanic in origin and the harsh desert environment has left them as expanses of exposed bedrock rising 305m (1000ft) above the valley with little or no vegetation. An existing 3.05m (10ft)

Jan 1, 1997

By S. D. Morrison, J. L. Watson

It is well known that the density and viscosity of a mill pulp have optimum levels for grinding efficiency, and sophisticated control loops are employed to control pulp density in industry. However, these control loops rely on a number of plant measurements, and often the input data will not permit effective determination and control of the mill pulp density. The use of a single remote pulp density measurement has obvious advantages, and it is suggested and demonstrated for laboratory batch grinding that mill noise measurements can indicate the effective density of the mill pulp. In addition, the mill noise is shown to indicate the actual effective pulp viscosity in the mill and hence permit the identification of the dynamic rheological regime existing in the mill. It is demonstrated that mill noise increases with grind time and, at any given grind time, with increasing pulp density in the pseudoplastic range. This increase in mill noise level with pulp density is interpreted as indicating a decreasing pulp viscosity. The results show that the transition from dilatant to pseudoplastic conditions within the mill, with increasing pulp density, can be identified by this increase in mill noise. When the pseudoplastic pulp started to exhibit yield characteris- tics, the mill noise fell dramatically. The technique of mill noise analysis is then used to investigate the effect of a grinding additive on the batch grinding of two ores. With a magnetite ore, the additive was shown to increase the mill noise, and hence decrease the pulp viscosity, in the pseudoplastic region and to increase the effective grinding. The molybdenite ore, however, did not show significant noise level changes and did not show improved grinding efficiency.

Jan 1, 1987

By Felipe Calizaya, Sekhar Bhattacharyya

Mechanized underground mines suffer from noise overexposure. Noise levels are often above the Permissible Exposure Limit (PEL) where underground fans are used. Sound levels in active workings can reach up to 121 A-weighted decibels (dB(A)), especially when fans are not equipped with silencers. Use of silencers seldom ensures PEL. Overexposure of noise induces permanent hearing loss among mine workers. A NIOSH-funded research project and field studies at six coal and non-coal mines revalidated the findings. The University of Utah undertook laboratory studies to reduce fan noise at the source. A new silencer prototype with varying noise dampening material was designed and tested. The silencer and associated extension can be repacked with different dampening materials. The silencer and the extension were used in various configurations. Attempts were also made to simulate field conditions. The tests demonstrated a maximum sound level attenuation of about 14 dB(A) at the fan discharge. A properly designed silencer offers lesser resistance and thereby better fan performance and lower energy cost. The re-packable silencer is more likely to be maintained properly. Lowering of noise level happens in audible frequencies (4000 to 8000 Hz) which are important in A-weighting.

By L. Evrard, M. Van Camp, J. Y. Yen, R. G. Reddy, D. Mantha

Viscosities of two industrial lead blast furnace slags have been experimentally determined as functions of composition and temperature. A Brookfield viscometer with alumina rods and crucibles were used. Experiments were carried out between 1200 and 1573 K in an argon atmosphere with up to 5% addition of FeO, MgO, and SiO2 to the slags. Results showed that 1) the viscosities of two slags decreased with increase in temperature; 2) addition of FeO decreased the slag viscosities; and 3) addition of MgO and SiO2 increased the slag viscosities. Use of the above slag compositions with the addition of FeO is recommended for successful lead smelter operation.

Jan 1, 2005

By Jianliang Li, Xi Peng, Guorong Lu

This paper describes a wind tunnel modelling study on airflow and pollutant concentration in a large open pit mine located in southern China. A 1:1000 scale model of the surface mine was fabricated and placed in a wind tunnel. Airflow velocity in the test section of the wind tunnel can be continuously adjusted from 0.3 m/s to 6.0 m/s. In this study, both the present pit condition and the projected final pit condition were modelled. Airflow direction and velocity profiles were obtained. The impact of wind direction and velocity on airflow was also studied. The pollutant concentration distribution in the open pit was simulated using smoke, and a distribution profile was obtained. Respirable dust concentrations at the mine site were measured, then its concentrations at the projected final pit condition were estimated using the obtained pollutant concentration distribution profile. Under normal meteorological conditions, it is expected that the respirable dust concentration for the final pit should not exceed the government standard. Key Words: wind tunnel modelling, open pit, surface mining, scale model, mine ventilation, airflow profile, point source.

Jan 1, 1993

By D. A. Elgillani, N. A. Abdel-Khalek

The role of ZnS04 in activation of sphalerite (ZnS) and deactivation of lead-activated sphalerite has been investigated. Adsorption of metallic ions at the solid-solution interface, electro kinetic results for sphalerite under different chemical conditions, and thermodynamic calculations were used to elucidate the mechanisms involved. It is shown that flotation response of sphalerite in absence of activators is rather weak and that adsorption of ethyl xanthate on the mineral mainly electrostatic in nature. Zinc sulfate is found to activate the mineral but only in a narrow acidic pH range. This is attributed to the increase of zeta potential as well as the possible increase in amount of negatively charged bulk precipitated zinc xanthate. Lead ions activate sphalerite in a wide pH range and the lead activated mineral assumes a flotation behavior similar to that of galena (PbS). However, addition of ZnS04 depresses the lead-activated sphalerite by replacing lead ions at the mineral/solution interface.

Jan 1, 1999

By D. A. Robbins

The application of remote sensing for environmental measurements is already being utilized. Aircraft mounted imaging spectroscopy has been utilized to evaluate areas of historical mining operations as well as active mine sites. To the extent that remote sensing can provide more sensitive, cost effective, and timely monitoring potential, the technology is of interest to the industry. Questions remain about the application and validation of the data and the availability of the technology in the private sector. This presentation will discuss some of the potential uses, benefits, and concerns related to remote sensing and efforts to monitor the technology's development.

Jan 1, 1999

By I. B. Tulu, M. M. Sears

In 2015, 40 longwall mines provided nearly 60% of the US coal production from underground mining methods. This represents a substantial yet gradual increase from just under 50% over the last 5 years. As a result of this increased production share, the percentage of ground-fall-related fatalities in longwall mines has also increased when compared to all US underground coal mines. Additionally, about 80% of ground-fall-related fatalities have occurred in areas where the roof was supported. In an attempt to better understand the status quo of current US longwall support practices, a sample of 25 longwall mines were visited representing nearly 50% of the currently active longwall mines representing all of the major US longwall-producing regions. The resulting data was obtained from a wide variety of overburden depths, geologic conditions, mining heights, ground conditions, support practices, and gateroad configurations. The data collected is reported using both qualitative and quantitative methods. Results from the research update previous efforts in classifying mining accidents and injuries as well as current support practices presented by this author at the 2017 Society for Mining, Metallurgy, & Exploration Annual Meeting. This data provides a necessary background for future research aimed at further reduction of ground fall accidents and injuries.

By W. F. Hahnert, P. A. S. Ralston

In off-line training of a rule-based controller, the significant measure of successful training is the quality of control provided by the generated rule set. In an adaptive or on-line control environment, performance is also measured by the ability to accurately maintain a satisfactory rule set, but within constraints on speed and/or resource availability. Very small population genetic algorithms, or microGAs, have been proposed as a means of capitalizing on the hill climbing characteristics of faster local optimization techniques while requiring less memory and retaining much of the robustness of traditional, larger population genetic search. A traditional genetic algorithm and a similar microGA are developed and applied to two control problems. The performance of these algorithms is analyzed with respect to (1) the quality of the rules learned, (2) the rate at which learning occurs, and (3) the memory resources required during learning.

Jan 1, 1993

By Terry L. Logan, Arfon H. Jones, James C. Seccombe

Deeply buried coal seams [greater than 3000 ft (914 m)] are difficult and sometimes hazardous to test and complete due to coal sloughing, formation pressure anomalies and coal fine generation. Data collected while stimulating two deep coalbed methane wells located at the Gas Research Institute/Resource Enter¬prises, Inc. "Deep Coal Sean Project" test site in the Piceance Basin, Colorado, is presented in this paper. A single thick coal seam was completed openhole in each well. Core data, reservoir data, in-situ stress measurements, and pre-stimulation calibration test data were collected at the site to use in the design of the fracture stimulation treatments for both wells. A nitrogen foam fracture fluid treatment was selected for the first well and a linear gelled water for the second well. Treatment pressures were monitored with a downhole quartz pressure transducer. Atypically high treating pressures were observed, possibly indicating coal fines plugging at the fracture tip or increase in fluid viscosity caused by interaction of the generated coal fines with the fracturefl uid. In addition, a comprehensive fracture diagnostic effort was employed during the fracturing of the second well; namely, triaxial borehole seismic, seismic televiewer, hydraulic impedance monitoring, gamma ray log (in conjunction with radioactive additives in the sand), and temperature log. The results indicate a vertical fracture was created parallel to the face cleat as expected.

Jan 1, 1986

The Chinese city of Shanghai is one of the fastest growing in the world. To keep up with the growth, two tunnels, three-lanes each, are being built beneath the Yangtze River to connect Shanghai with the Changxing River Island. To complete such a large project, Herrenknecht Tunneling Systems was brought in to construct the largest tunnel boring machine (TBM) in the world. The first Herrenknecht S-317 Mixshield has a diameter of 15.43 m (50.62 ft). It was built to construct one of the two 7.2-km (4.5-mile) tunnels. The tunnels are part of the Changjiang Under River Tunnel Project and will be at depths of up to 65 m (213 ft) beneath the Yangtze River in Shanghai-Pudong. These two tunnels are to be opened to traffic in April 2010, in time for Shanghai to host the World Expo. More than 20 million people live in the Shanghai area. The area itself has been growing at an extremely rapid pace for more than a decade and is in need of more space. The search extended beyond the natural limits of the Yangtze River Delta. As part of its incredible growth, 500 new vehicles are registered every day. The new tunnels will connect the Changxing River Island, with a population of approximately 600,000 people to the road traffic network. A bridge construction will also provide a traffic link between Changxing Island and the large island of Chongming.

Jan 1, 2007

By D. Zaharaki

The present experimental study underlines the advantages of factorial design in environmental, geotechnical and waste management experimentation. A typical case study regarding solidification of metallurgical wastes is presented and the main effects and interactions of three main factors are determined in order to establish the optimum experimental conditions in terms of compressive strength. Finally, a regression equation that predicts accurately the real compressive strength of a specimen under various experimental conditions is derived.

Jan 1, 2005

By Timothy J. Matthews, Ted Klemetti, Timothy J. Batchler, Daniel J. McElhinney

Unplanned tailgate collapses and difficult mining conditions in U.S. longwalls have necessitated the use of innovative tailgate support systems. Severe ground movement induced by longwall loading has caused operators to utilize secondary support systems that can match yield and strength requirements with expected ground reactions. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Pumpable roof supports are currently being used to provide a safe working environment for longwall mining. A full understanding of the impact of these performance characteristics is necessary to optimize the support application and to provide a foundation for making further improvements in the support performance. Optimization of roof support applications helps to ensure the protection of mine workers by preventing roof falls due to inadequate support design. The load capacity and stiffness characteristics of a 27-in.-diameter pumpable support system was evaluated using the National Institute of Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS). Previously, tests to evaluate the performance characteristics were performed on a single pumpable support. The goal of this new research is to evaluate the performance characteristic effects of the pumpable support system and compare it to an individual pumpable test examination. This research of a pumpable support system configuration simulates the current installation practices in U.S. coal mines.

Jul 1, 2023

By S. K. Kawatra, S. J. Ripke

Finely disseminated iron ores compose much of today's reserves. After removing the silicate gangue, the resulting fine iron oxide concentrates require pelletization with a binder to enable transportation and reduction. Binders can be used more efficiently if their binding mechanisms can be completely understood. Typically, bentonite clay is needed as a binder to improve the strength of the pellets. Bentonite is an effective binder at a relatively low cost, but costs could be reduced further by replacing bentonite with even lower-cost binders, such as high-carbon Fly-Ash Based Binder (FBB). In this study, it was found that bentonite binds by a physical mechanism, while FBB binds by a chemical mechanism. These mechanisms were determined to be incompatible. Partial replacement of either binder with the other reduced dry magnetite pellet compressive strengths below the industrially acceptable value of 22.2 newtons (5 lbf). Activators and accelerators that activated the fly-ash deactivated the bentonite. The incompatibility of these two binders is explained.

Jan 1, 2000

By Steve Karl

Introduction US steel production dropped 5% in 1985 to 79 Mt (87 million st). US operators are producing at only about 65% of capacity. More than 600 steelmaking facilities have closed in just 10 years. And McDonalds Corp. now employs more people than the entire US steel industry's 200,000. Not gloomy enough? Well, the North American iron ore industry can expect more plant closures and capacity reductions in the coming years. And don't count on the Federal government's voluntary restraint agreements with foreign steel producers to bail out the industry. In 1985, the first full year of the restraint agreements program, steel imports were more than 25% of domestic consumption, well above the 18.5% target. That's the grim truth, according to M. A. Hanna's Robert F. Anderson. Hanna's chairman was speaking to a group of iron ore, taconite, and steel industry executives at the Minnesota Section AIME meeting in Duluth in January. Despite those depressing facts, Anderson said he believes the domestic iron ore and steel industries can survive, although they will both be shadows of their former selves. But, he is giving them five years to make the necessary adjustments or both will die. Major steel producers during the last four years have added about $7 billion in losses to their books, he said. In Minnesota's Iron Range, employment in iron ore and taconite has gone from 14,000 10 years ago to less than half that today. Anderson explained that steel producers have more capacity today that more than meets their demand for iron ore. This places great pressure on iron ore producers to restructure to survive. Hanna, for example, has been forced to close or divest its iron ore interests in Missouri, Michigan, Canada, and Minnesota since 1980. The latest casualty was the company's Butler taconite project in Minnesota. "In just five years we've reduced ownership of active pellet capacity by 80%," he said. Technological ironies Improved technology is one cause of the industry's woes, Anderson said. While these improvements are welcome in terms of remaining competitive, the irony is that some of these technological improvements are coming at the expense of the iron and steel industries. There is a growing demand for lighter and less expensive substitutes for steel. Automobiles contain about 318 kg (700 lbs) less steel than they did 10 years ago. And, Anderson said Ford Motor Co. has indicated it plans to reduce steel usage an average of 50 kg (112 lbs) per car in the next few years. One leading steel analyst has predicted that steel usage in cars will fall another 40% in the coming years. Improved steelmaking technology has also decreased raw steel production. Continuous casting is more efficient than traditional forms of steelmaking, Anderson said. Continuous casting accounted for about 43% of steel production in the US last year, compared to 9% a decade earlier. And, Japan and Korea are producing more

Jan 3, 1986

By John F. Bryce, Fazley A. Azhar

With increasing economic pressures to produce more with less, the material handling industry is turning to engineered solutions to reduce the number of people required to operate its facilities, monitor maintenance trends, pin point problems, increase throughput, decrease downtime, identify weak links in the production system, and increase times between scheduled maintenance. One solution to these problems is to implement a Total Control Solution (TCS) using industrial computers, fieldbus networks, and distributive Input/Output (I/O) for control, automation, data acquisition, and analysis. This paper will discuss some of the control fundamental principles used by Technisys, Inc. (TI) to implement TCS.

Jan 1, 1998

By S. K. Kawatra, S. T. Bagley, T. C. Eisele

The use of the bacteria Thiobacillus ferroxidans to catalyze pyrite dissolution in coal is well known, and recent investigations have shown that T. ferrooxidans are also capable of rapidly altering the pyrite surface to facilitate its removal from coal by froth flotation and oil agglomeration. However, the effect of reactor design on the bacterial leaching rate is poorly documented, and the ability of bacteria other than T. ferrooxidans to affect pyrite flotation has been unknown. In this study, the effect of a number of different microorganisms on the flotation of unoxidized pure mineral pyrite has been investigated, and it was shown that organisms other than T. ferrooxidans are also capable of depressing pyrite flotation. In addition, comparative studies of leaching in shake-flasks and pachuca tanks have shown that the pachuca tanks allow leaching to proceed to a greater degree and at a significantly accelerated rate.

Jan 1, 1989

By Dean E. Albon

In the late 1940's and early 50's in southern Illinois, the usual open pit blasting in the coal field consisted of one or two rows of churn drilled vertical holes being shot with instant electric blasting caps. The entire shot detonated at one rime. In southern Indiana and Ohio most mines were drilling horizontal holes and they too were primed with instant EB caps. During the ten years from 1355 through 1965 many changes occurred in drilling and blasting methods. The churn drill in southern Illinois and the horizontal drill in Indiana and Ohio were replaced by the rotary vertical drill. The ammonia dynamites and liquid oxygen explosives were replaced by ANFO. The elctric blasting cap in the hole was replaced by a detonating cord down line and detonating cord trunk lines made the connections between holes and rows of holes. Host open pit mining was in areas far enough from town that the noise and vibration from blasting was, if not ignored, at least tolerated. During the 1960's open pit mining expanded to account for nearly 50% of the coal produced. Mines came closer to town and towns expanded along the highways with suburban homes and mobile homes. The mines began receiving complaints about the noise and vibrations from blasting operations.

Jan 1, 1976

By Robert S. MacPhail, Bret G. Cousins

Many copper-bearing ores with associated gold use Sodium Isopropyl Xanthate (SIPX) as a flotation agent. In general, SIPX will float to some extent other minerals that may not be desirable, such as pyrite. FLEX 31 is a chemically enhanced SIPX product with many of the same properties as SIPX. But FLEX 31 has the ability to reject more pyrite from concentrates and improves copper recovery when using up to 50% less FLEX 31 than is required if using SIPX. Copper activated minerals such as sphalerite and arsenopyrite show increased recoveries as well using FLEX 31. Tests have been performed on copper/zinc ores and an arsenopyrite/pyrite ore.

Jan 1, 1995