Search Documents

By J. G. Groppo, S. M. Khandrika, B. K. Parekh

It is shown that dewatering of fine coal particles (D50 = 21 µm) is enhanced near the point-of-zero-charge. The coal surface is modified by the addition of copper ions and by adjusting the pH to precipitate surface-active metal hydroxy species, which promote agglomeration and produce low-moisture cakes. Filtration kinetics data are used in calculating filter cake parameters from an integrated form of Darcy's law. The influence of copper ions and pH on filter cake parameters and the correlations among them are presented.

Jan 1, 1995

By Joao Felipe Costa, Jair Carlos Koppe, Alexandre Grigorieff

Discrepancies in raw materials properties informed by both producer or consumer is a common problem in most areas of the industry. Commercial contracts in the mineral industry normally penalises the producer, if contaminants in the ore exceed established limits. In some situations, the supplier is penalised if the quality of the ore is below a contracted amount. Differences in lab analysis are due many sources of error, such as distinct practices used in two laboratories for sampling, preparation or analysis. Rigid contracts impose to the miner the use of rigorous quality control program and in these situations sampling plays a major role. Sampling theory provides the tools to analyse errors involved in sampling, preparation and analysis. This paper proposes a methodology to check the precision and accuracy of a given sampling protocol emphasising the application of Gy's sampling theory to broken ore. A procedure to measure the error on each step of the protocol is introduced and the results compared to the fundamental error measured by Gy's theory. The results show the applicability of the method and its relevance to audit sampling procedures aiming at error minimisation. The methodology is illustrated in a case study at a major coal producer in Brazil.

Jan 1, 2002

By J. A. Procarione, M. K. McCarter, Bradley C. Paul

A numerical technique is described which can be used to model the quantity and distribution of air flow through broken rock. The method can also describe gas concentration and temperature distribution. A computer code implementing the numerical approach was developed to assist in determining the feasibility of a proposed modified in-situ leaching method for extracting copper from sulfide porphyry deposits. This mining method requires air to be forced through cells of rubblized ore. The flow serves to supply oxygen for the leaching reactions and to dissipate heat that would other-wise build due to the exothermic reactions. The method substitutes the Carman equation into the Laplace equation. The solution of the resulting non-linear formulation is done on a finite difference grid using SOR with iteration improvement of coefficients. This procedure yields the required air flow pattern and pressure drop. An equation for advection with absorption is then solved over the same grid using explicit schemes to yield oxygen concentration. Finally, a similar technique is applied to the convective heat transfer formula to yield the temperature profile. The model is potentially applicable to such mining problems as the prediction of leakage through caved ground, the prediction of methane concentration in gobbed ground, and the prediction of heat build-up in caved workings.

Jan 1, 1989

By S. S. Peng

Horizontal stress is an important factor that contributes to roof failure during longwall entry development, especially when the immediate roof is weak. In this paper, the effects of stress angle between the maximum horizontal stress and entry development and stress ratio of the maximum to minimum horizontal stresses on the stress distributions in the weak immediate roof of a three-entry system are analyzed using the finite element method. The results have confirmed that stress angle has a significant influence on the stress distributions. Generally, the three-entry system is in the worst stress condition when the stress angle is about 60° to 75° . The stress ratio has also some effects on the roof stresses.

Jan 1, 2000

By J. W. Danni

Today's mining industry faces many challenges. Perhaps none is more important than the challenge of improving our industry's public image. Opinion polls document public concern for a clean and safe environment. As part of that public, the mining industry must share that goal. The public is now the most powerful environmental group in society. And the public wants the environment to be protected. In May 1989, Edgar S. Woolard, chairman of DuPont, spoke to the American Chamber of Commerce. He said that industry's continued existence "requires that we excel in environmental performance and that we enjoy the non-objection - indeed even the support of the people and governments in the societies where we operate." In effect, Woolard called for "corporate environmentalism." He defined it as an "attitude and a performance commitment that places environmental stewardship fully in line with public desires and expectations." Environmentalism is no longer a fringe activity, but rather is now clearly in the mainstream. How can we meet public expectations and improve our image as an industry? One of the best ways is to plan, design and operate our mine facilities with environmental responsibility and social concern. The Mineral Hill Mine provides a good case study of a facility that has made this commitment. The project used an inter-disciplinary, multiagency task force, citizen advisory groups and engineering and design considerations. As a result, Mineral Hill achieved cost-effective permitting. At the same time, the operation demonstrated effective "corporate environmentalism."

Jan 1, 1992

By M. Misra

The interaction of xanthate with SO2 in the flotation of sphalerite and chalcopy.ite is discussed. 'The SO depression of sphaledte is due to the decomposition reaction of xanthate by SO2 The decomposition reaction is dependent on the cole ratios of xanthate/SO2, oxygen concentration and pH. Xanthate adsorbs at a faster rate by chalcopyrite than sphalerite. The faster rate of xanthate adsorption by chalcopyrite and the specific action of S02 on the surface of chalcopy.ite facilitate the selective separation of chalcopyrite from sphaledte.

Jan 1, 1989

By B. Elevli

Production scheduling of an open-pit mine is one of the most important steps in open-pit mining. The production schedule of a mine defines the distribution of cash flows and as a result directly influences the net present value (NPV) and overall economic feasibility of a project. Although the need to plan and operate a mine with an optimum production schedule has been obvious for some time, the methods used to obtain such a schedule have not been. The current practice for doing is to do it by hand on the basis of trial and error analysis. In an attempt to improve the way production scheduling is currently done, a new computer based production scheduling algorithm is developed. This paper describes the fundamentals of this newly developed heuristic scheduling algorithm and its application on a gold deposit. The results coming from a case study show that the schedules based on the new method provides improved cash flows compare to a manually done production schedules.

Jan 1, 1989

By Wang Yingmin, Xu Zhuyun

The optimum of general mine ventilation networks is very difficult and has a considerable significance. Based on the content model, this paper presents a more general nonlinear programming model whose number of variables equals that of independent meshes. The constrained conditions are linear inequalities only. The model is changed into an unconstrained problem with multiper method. The optimum results are computed with DFP algorithm and the Improved Golden section method is used in its linear searching. The computer program written in Quick BASIC is suitable to the optimum of any type of large mine ventilation networks with different regulating devices. The paper presents two examples for optimum of ventilation networks.

Jan 1, 1991

By Charles J. Hass

INTRODUCTION Deformation measurements are some of the simplest and most useful measurements that can be made by the mining/rock mechanics engineer in assessing the sta¬bility of openings in rock. A number of tools and tech¬niques are presently available. This chapter will de¬scribe the most common instruments, their application, and present the equations needed for data reduction. MECHANICAL STRAIN GAGE Description of Instrument A mechanical strain gage of the Whittemore type shown in Fig. I is a useful instrument for measuring deformations of pillars, sidewalls, and roofs of under¬ground mines. Measurement gage lengths typically range from 51 to 254 mm (2 to 10 in.), and the dial indicator reads to 0.0025 mm (0.0001 in.). The instru¬ment measures the deformation between precision gage points which are anchored in the rock. The anchor points are typically grouted in small holes drilled 12.5 mm (1/2 in.) or so deep into the rock. Strain a is calculated from the measured deformation AL with the equation [ ] where L is gage length. A necessary accessory for the instrument is a master bar normally made from invar steel having a low co¬efficient of thermal expansion. This bar allows one to check the instrument for changes in the mechanical zero point and to correct for temperature effects on the measuring instrument. The instrument is available from Soiltest, Inc. for a cost of approximately $340; the cost of the master bar is approximately $55; and nonreusable brass inserts which are anchored in the rock are nominally priced at $0.27 each. All prices are for 1978. Applications Two classes of applications may be considered, one where only one measurement direction is involved and the second where three measurement directions are em¬ployed. Applications where only one measurement di¬rection is necessary include: monitoring crack or frac¬ture separation or shear movement with anchor points on opposite sides of the discontinuity; measurement of vertical strain in a pillar or sidewall; and measurement of steel support deformations with anchors in the steel members. The more general application involves a strain ro¬sette consisting of three measurement directions which for convenience are oriented 1.04 rad (60°) apart to form an equilateral triangle as shown in Fig. 2. Strains in the three measurement directions [ ]

Jan 1, 1982

By A. E. Hall, K. R. Mutama

The wind tunnel has been used extensively for mine ventilation research and continues to be a valuable tool. The advent of the powerful personal computer has reduced the use of wind tunnels because several flow problems car be simulated and investigated quickly. This paper describes the recent design and construction of a wind tunnel which is now being used for mine ventilation aerodynamic research and teaching purposes. The wind tunnel has a square cross section measuring 900 by 900 mm and is 8485 mm long from the entrance to where it joins the fan. The tunnel was designed as an open circuit suction type and is attached to a 7.5 kW variable pitch axial flow fan capable of producing over 6 m3/s of airflow. The entire length of the wind tunnel can be used for flow investigations and all activities are visible since the sides are made of plexiglass. Results are presented from the test program to show that even without honeycombs and screens air flow symmetry is achieved.

Jan 1, 1993

Horizontal stress is an important factor that contributes to roof failure during a long wall entry development, especially when the immediate roof is weak. In this study, the effects of the three factors, the stress angle between the maximum horizontal stress and entry development, the stress ratio of the maximum to the minimum horizontal stresses, and the sequence of entry development, on the stress distributions in the weak immediate roof of a three-entry system are analyzed using the finite element method, when the horizontal stress is fixed. The results have confirmed that the stress angle has a significant influence on the stress distributions. Generally, the three-entry system is in the worst stress condition when the angle is about 60°_75°. The stress ratio has little effect on the roof stresses. In addition, the sequence of entry development has also little effect on the roof stress for the specific case analyzed.

Jan 1, 1999

By Scott A. Norby

Kennecott's Ray Mines Division (RMD) is located in central Arizona. The pit and silicate plants are located at Ray while the 27,500 tpd concentrating facilities are located at Hayden, approximately 20 miles away from the pit. Ore is delivered in 100 ton railroad cars, 60 cars per train via the Copper Basin Railroad. The side discharge cars are dumped into a 6,000 ton trackhopper. There are 6 Nico feeders, two per belt. Three 48" belts transport the -8" ore to three 7' standard (secondary) Nordberg crushers. Each crusher is preceded by a 6' x 12' Tyler double deck screen. The secondary crushers are open circuit. The -1/21t material from the screens is transported directly to the fine ore bin at the mill. The discharge from the crushers and the intermediate product -2 1/411 x +1/2" is conveyed to a surge bin. The tertiary crusher feeder belts discharge onto five 61 x 161 Tyler double deck screens, each followed by a 7' shorthead (tertiary) Nordberg crusher in closed circuit. The -1/2" product joins the -1/2" ore from the secondary crushers and both are conveyed along a 42", 4,230 foot long belt to the fine ore bin that feeds the grinding circuits. When hard ore is experienced at the concentrator the daily throughput decreases by up to 10%. This coupled with the fact that the ore is generally becoming harder with mine depth provided the incentive to improve the performance at the crushing plant.

Jan 1, 1986

By Edehran Lotfi, Terrence Stobbe

INTRODUCTION Mobile excavating and handling equipment are important 'tools of trade' in the mining and construction industries. The handling of this equipment must be mastered so that its limitations are learned and its harmonic use with other pieces of equipment is practiced. he sudden growth in mobile excavating and handling equipment type, size, complexity, and application started after the Second World War. This growth has not been accompanied by pertinent human factors research. Investigations into the proper and safe handling of such equipment with due regard for human and machine limitations are lacking. One such piece of equipment is the front-end loader (FEL), which during one cycle of operation excavates, loads, and hauls, (Lotfi and Adler, 1981). The diversity of action by FEL is archetypical among excavating and handling equipment. Front-end loaders are the most rapidly proliferating type of equipment in the industry. Also, front-end loaders are involved in the highest number of accidents involving mobile excavating and handling equipment. In the period 1970 to 1978, FEL's were involved in 27% of all mobile equipment accidents in surface mining (Adkins, 1980). Improving operational safety and efficiency will reduce the frequency of accidents. The performance of the operators can be evaluated and improved by the following steps: first, define the operating conditions and the operator workload intensity (Adler and Lotfi, 1983), second, monitor the operator to evaluate his task performance, and third, make recommendations based on the findings. The stressful nature of the equipment operating task is an acknowledged fact (Field, 1980). However, a systematic measurement of stress evaluation is lacking. In this paper, methods for measuring mental stress and fatigue, are defined, the mental load which caused the stress is outlined, and stress measurement methods are proposed. MENTAL STRESS Mental stress has been described as a "specific somatic response to damage or the threat of damage by several environmental agents"

Jan 1, 1986

By Ivano Andreis, Giovanni Valent

The Yindaruqin Irrigation Project is designed to irrigate 57,000 ha of land in the central part of Gansu Province of People's Republic of China. Water for the Project will be diverted through an 87 Km long feeder canal which will convey 36 cubic meters per second from an intake on the Datong River. (Fig. 1) The feeder canal consists of approximately 10 Km of open channels, 75 Km of tunnels and 2 Km of siphons and aqueducts. This is the biggest self-flowing irrigation water control project in the Northwest of China and it is among the most interesting projects in China for the geological and environmental conditions. Nearly half of the investment in the Project is a World Bank Loan and contractors were chosen by means of international bidding. The Italian Company, CMC Ravenna, succeeded in answering the bidding for the construction of tunnels 30A and 38, perhaps the most difficult in the Project, submitting a TBM alternative to the conforming drill and blast contract recommendation.

Jan 1, 1993

By Dennis Keay, Barbara Schickner, P. L. Longenecker, Glenn J. Philips, Lee Rice, Herman E. Knight, Wayne E. Veneman, B. W. Washington, Robert S. Hess

The outlook for coal continued to improve in 1980, fueling expectations that a long-awaited boom is at hand. The surprising surge in coal exports contributed to the latest wave of optimism. Overseas exports hit 66 Mt in 1980, buoyed by a significant increase in demand for steam coal, up from 1979's 2.3 Mt to 15 Mt in 1980. US coal production rose 6.9% to 750 Mt in 1980 and total coal consumption increased 8.1% to about 725 Mt, due primarily to higher world oil prices and setbacks in the US nuclear power industry. Yet the industry is beset with problems-both internal and external. Although demand for US coal is growing, the industry's excess productive capacity is estimated at over 90 Mt/a. Public utilities, where real increases in coal consumption must come, are still moving slowly, blaming delays on antipollution equipment costs. Coal supplies are uncertain, subject to the vagaries of the UMW. For the sixth time since 1964, the coal industry and UMW failed to renew their labor contract without a national strike, reinforcing the perception held overseas that the US is not a reliable supplier. The expected boom in coal exports will, in part, depend on our ability to assure foreign buyers that US sources are dependable. The US industry is also plagued by inadequate facilities linking mines and consumers: inadequate rail systems, coal ports, and barges, For US producers to be competitive, ports must be expanded, rail lines improved, and harbors dredged to allow 136-kt ships to load coal. The im¬provements will require an enormous commitment and investment. Despite these major problems and unresolved issues, two factors continue to favor an increased reliance on coal as an energy source: abundant US reserves and coal's comparative price advantage. Coal's performance in the 1980s may at last exceed its promise.

Jan 5, 1981

By Kenneth R. Dickson, I. Michael Gowring, Gary M. Davey

The Kemano Power Tunnel is currently being constructed by a joint venture of Atkinson, Kiewit, and Commonwealth. The 5.73 m diameter, 16.1 km long tunnel is part of the Kemano Completion Project in British Columbia, Canada which is being developed by Alcan Smelters and Chemicals Limited. The discussion includes the refurbishment and development of Robbins TBM 189-229 previously used at Calaveras (RETC Proceedings, 1987), the logistics of conducting a tunneling operation in a remote area with adverse weather conditions, in addition to a description of the work and the performance details in the various geological conditions encountered to date.

Jan 1, 1991

By R. L. Grayson, S. Yuan

A goal-programming-based, worker-scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model, the accomplishment of each regular and non-regular job is a goal, and the objective is minimization of the deviations from the goals. A number of coefficients are employed as premultipliers of the decision variables to address practical considerations associated with the utilization of workers and the requirements of jobs. This model is applied to a 41-worker problem.

Jan 1, 1992

By R. S. Mateer

Linear programming on desktop computers is commonly used to optimize coal blending proportions. The objective function is usually the cost of the blend. The constraints consist of materials and heat balances as expressed as linear functions of the blend. This is illustrated in Example 1. Inclusion of a sulfur compliance constraint in more complex because the maximum permitted sulfur percentage is not a pre-specified constant. Rather, it is a function of the calorific power of the blend itself. The current limit of 1.2 pounds of sulfur dioxide per million Btu may be expressed as: [Sulfur Max%= 0.6 . Hl10,OOO with H in Btu/lb.] A proper constraint equation may be formed by defining for each coal a function that is the difference between the actual sulfur percentage and the maximum sulfur percentage. This may be regarded us an excess sulfur percentage. For Coal A of Example 1. this would be: [ Sulfur Excess%=0.5-0.6 13,000/10,000=-0.28] This value would be used as the coefficient of the weight proportions of this coal in the blend. The complete constraint equation would then be the sum of such terms for each coal set less than or equal to zero. This is illustrated in Example II. [ ]

Jan 1, 1995

By R. C. Karra

Mining is one of the oldest profession and second after agriculture. Unfortunately Mining is not so familiar in the society. Due to lack of recognition in the society, existence of mines in remote places and in dusty and humid working conditions, led the poor response for mining engineering. Mining engineering programs have been increasingly less attractive to the student population over the years due to negative image of mining industry. After graduating in mining engineering, there is not much problem of employment at present. In the last 10 to 15years most of the mining engineering graduates have joined software industry. Even those joined in mining industry also left with in 2 years of service. The main reason for this is not being satisfied with job, it is not only working conditions but also work environment, work culture, remote location of the mines etc. Though many were trying to leave mining profession, the recent economic slow down has prompted some of them to incline towards job safety and retained to mining job. At this juncture a systematic study was taken up to analyze the job satisfaction of mining engineers in India.

Jan 1, 2011

By James C. Puckett

The mining industry finds itself in the middle, between the need to increase production of our energy resources and the necessity of minimizing the environmental impact. Using the recent past as a guide, the mine planning engineer's function will continue to increase as further coal quality constraints are made upon the production staff. The engineer will need to make use of all available tools in order to provide timely answers to the complex "what if" questions that arise. This need to consider many alternatives is bringing about a rapidly increasing acceptance and utilization of the computer. In the areas of data handling, mineralization modeling, and production simulation, the computer is an effective tool for the mine planning engineer. Described herein is a coal data storage and analysis system developed to provide timely answers to the "what if" questions for an operating strip coal mine in Montana. The characteristics of a computerized coal data base and coal quality planning system are outlined in this chapter. The system has been developed for use at a particular coal mine; however, it has applicability to coal mines in general. Fig. 1 is a flow chart showing the functional relationships of the system. There are three main file types: the drill-hole data base, the boundary file, and the zone file. The purposes for which each file is organized are illustrated on the flow chart.

Jan 1, 1979