Search Documents

By A. W. Laughlin

Laser-Induced Breakdown Spectroscopy or LIBS can be used to provide exploration companies with precise and accurate chemical analyses in the field, in real-time, resulting in major time and cost savings. Using a Field-Portable Analyzer (FPA), anomalies can be followed up immediately while crews are still in the field. Lower limits of detection (LLDs) are element dependent, but many are sufficiently low to be useful in exploration. LLDs in ppm for selected elements of interest are: Be-2, Cu-3, Zn-20, As-200, Sb-500, Pb-30, Ag4, Mo-100, B-33, Ti-500, V-350, and Cr-1. LIBS analyses require little or no sample preparation.

Jan 1, 1999

By Robert L. Runkel, Kenneth E. Bencala, Briant A. Kimball

Thousands of abandoned and inactive mines are located in environmentally sensitive mountain watersheds. Cost-effective remediation of mining sites in these watersheds requires knowledge of the most significant sources of metals to surface waters. The significance of a given source not only depends upon the concentrations of a toxic metal, but also on the total mass, or load of metal added to the stream. To determine loads, we combined tracer-injection methods, to provide reliable discharge measurements on a watershed scale, with synoptic sampling, to provide spatially detailed concentration data. The resulting load profiles indicate which sources have the greatest effect on streams, where natural attenuation of metal loads occurs, and where ground-water inflows are located. This is part of the information needed for planning remediation of mine-drainage effects. The approach is illustrated by comparing zinc loading curves from three watersheds affected by mine drainage.

Jan 1, 2000

By A. H. Reitsema, Hans E. van Dam

In CIP, CIL, and Heap Leach gold recovery operations, a sub-optimal activated carbon performance invariably causes a significant loss of revenues. In this paper it is shown, how dedicated analyses of carbon samples can be used as a guide in plant performance optimiza­tion. Firstly, a brief outline is given of the most important methods of analyses, including the specialized methods not normally used by mining operations, but provided by carbon manufacturers. Then, a number of practical cases are discussed in which carbon sample analyses provided insight which allowed significant improvements.

Jan 1, 1995

By S. A. Matthews, M. L. Nave

AC variable frequency motor drives are emerging technology for belt conveyors. The success of the application in mining depends on adequate and timely consideration of drive, motor, and conveyor features. The purpose of this paper is to familiarize and inform possible mining users of AC variable frequency drive attributes.

Jan 1, 1998

By Christophe Bragard, Jason Choi, William H. Hansmire

This case history provides a physical benchmark of tunneling technology progress comparing an old hand-mined tunnel to a modern 20-ft-diameter EPB TBM that mined in the same ground. This rare opportunity to see how tunnels were constructed many years ago occurred when an old 10-ft-diameter storm drain tunnel in the way of os Angeles subway construction was demolished and replaced with obas berglass pipe. Steel rib and lagging initial support was exposed showing solid-sawn 2" × 12" × 48" redwood lagging. This paper documents the as-built old tunnel, how it was successfully replaced, and some lessons learned.

Jun 23, 2024

By M. L. Nave, R. E. Melley

DC motor drives are available technology for belt conveyors. The success of the application in mining depends on adequate and timely consideration of DC drive features. The purpose of this paper is to familiarize and inform possible mining users of DC drive attributes.

Jan 1, 1996

By Thornton L. Neathery

A small area in the Alabama Piedmont was studied to determine if metallic enrichment was associated with local magnetic anomalies. Cores from two holes in these magnetic anomalous areas have sulfide (pyrite, pyrrhotite, chalcopyrite) film on slicken-side and fracture surfaces. Two hundred and fifty soil samples were collected from the top of the "B" horizon on 1, 000 foot centers over the general trend of magnetic anomalies. Soil samples were leached with a 1:2. 7 mixture of HF and H2SO4 and the dilute filtrate analyzed for Cu, Pb, Zn, Ni, Co, Cr, Mo, and Cd, using atomic absorption methods. Concentration-value maps were prepared for each element. Small areas of anomalous concentrations were defined for Cu, Pb, Zn, Mo, and Ni. Some of these areas generally coincides with magnetic anomalies. Concentration values (ppm) range from: Cu 165.0 - 0. 5; Pb 265. 0 - 0.0; Zn 1386.0 - 43. 0; Ni 187.0 - 10.0; Co 207.0 - 6. 5; Cr 117.5 - 2.0; Mo 95.0 - 0.0; and Cd 32. 5 - 2.0. Studies of other magnetic anomalies appear warranted.

Jan 1, 1972

By Nick Chlumecky

INTRODUCTION Column-type supports are used to prevent roof falls in underground excavations. The first individual column supports were made from timber that was cut to fit the irregular heights of mine seams. Because the seam height of the material removed varied throughout the mine, timber posts generally could be used only once. During the I 920s, steel friction props began to appear in British and European mines, and, by the 1950s, thousands of these props were being used. However, the steel friction props were heavy, difficult to install, and difficult to recover. Furthermore, the friction props could not be preloaded, and their yielding behavior was rather erratic. In 1946, hydraulic props were introduced in En¬gland, and, within a few years, they replaced friction props throughout Europe. The first application of hy¬draulic props in the United States occurred in the 1950s, during early experiments with longwall mining. Modern technology and high-production mining procedures have combined to make the use of hydraulic props a very acceptable method of providing temporary heavy-duty support for production areas. In areas such as development headings, where only modest roof loads are expected, lighter-duty jackscrews, ratchet jacks, and light hydraulic props are used. ADVANTAGES OF HYDRAULIC SUPPORTS The acceptance of hydraulic supports has been wide¬spread during the past 25 years, proving their reliability and effectiveness in preventing roof falls. Some of the advantages provided by hydraulic supports are: 1) Individual hydraulic props can be installed within 30 sec, resulting in a minimum exposure of per¬sonnel and equipment to an unsupported roof. 2) Hydraulic props can be preloaded to more than 4.5 t (5.0 st), increasing the frictional resistance between the rock strata. Thus, the roof is kept tight, improving the behavior of the unsupported ground. 3) If gradual roof sagging or bottom heaving im¬poses an irresistible force, the hydraulic prop yields gradually and continues to support the ground. 4) The support capacities of the hydraulic props most widely used range between 10 and 20 t (11 and 22 st). Their support capacities are maintained during yielding to an irresistible force. 5) Hydraulic props can be recovered rapidly. Where no other supports are provided for the roof, as in pillar¬ing operations, the hydraulic props can be recovered by remote means. 6) The length of hydraulic props is readily adjust¬able allowing them to be reused in seams where roof height varies. 7) Studies of mining operations indicate that the use of hydraulic props increases both personnel safety and mine productivity. DESCRIPTION Figs. I and 2 illustrate typical hydraulic props used in mines in the United States. Fig. I illustrates a prop

Jan 1, 1982

By Yves Picot

Construction of new installations was recently completed in the Port of Tubarao, Brazil, With this expansion the port, operated by Companhia Vale do Rio Doce (CVRD), has become the largest iron ore port in the world, with an annual throughput capacity of 60 million long tons. GROWTH OR IRON ORE EXPORTS Since its formation CVRD has steadily increased the shipment of iron ore to overseas markets. Starting with less than 100,000 tons in 1942, the yearly export volume grew to 1,500,000 tons in 1951, 5,000,000 tons in 1961 and 25,000,000 tons in 1971. The number of different grades of ore also increased during this period. Production of high grade pellets, starting in 1970, further increased the number of ore products to be shipped. In the same period the size of ore carriers increased twenty-fold to over 250,000 DWT.

Jan 1, 1974

By F. Leschhorn

A computer model for long-term production scheduling is presented. By combination of different operations research algorithms it has been possible to design a system which is able to solve difficult long-term planning problems. The practical application of the model by a west-german hard coal mine is shown. It is proven that the EDP-model provides substantial support to the planning engineer by solving complex optimization problems.

Jan 1, 1989

By M. E. Rossi, V. Camacho

Reconciliation of production information is critical to evaluating the effectiveness of predictive models that would allow for the optimization of mining operations. Whether mining open pit or underground, mine-to-mill reconciliations can be one of management's better tools for the performance of proper accounting. Such reconciliations can also be a very useful tool in evaluation and optimization. This paper proposes a set of criteria and objectives for a typical reconciliation program. This paper also presents a stepwise, logical approach to performing reconciliations and discusses the benefits associated maintaining good information. It also highlights some of the potential pitfalls involved and the methods used to avoid collecting misleading information. These issues are illustrated with an example of a model-to-mine-to-mill reconciliation program that is being implemented at an operating mine. The program involves multiple predictive models (long-term and short-term block models), feed from three open pits and one underground mine, in addition to intermediate stockpiling, for a total of 23 mill streams. This paper presents a summarized version of this reconciliation program and its initial results as implemented at Minera Michilla S.A.

Jan 1, 2000

By N. B. Aughenbaugh

Compacted, fine-grained soils, often referred to collectively as clays, are used as permeability barriers in many mineral engineering projects such as heap leaching, containment ponds, tailings disposal and earth dams. Source materials for these liners include a variety of sand, silt and clay admixtures. These exhibit dramatically different engineering properties when densified. Therefore, it is imperative to adequately assess and characterize any soils being considered for compacted liners. The permeability and plastic properties of fine-grained soils are reviewed with respect to the state of compaction as the water content varies. Because they are weak in tension, compacted clays are susceptible to cracking when subjected to differential flexural movements. Designs of compacted clay liners also must include an evaluation of their flexibility. That is the ability of a fine-grain soil to bend plastically without cracking. This paper will also discuss the importance of flexibility with respect to soil types, compaction effort, failure mechanism and testing evaluation to the performance of clay liners in preventing seepage of pollutants from a containment site.

Jan 1, 1991

By Jack S. McPartland, Gene E. McClelland

It is advisable, for any heap leach project, to develop an historical metallurgical data base to predict production heap performance before ore is mined and placed onto the heap. A data base would include results from: interval assays, cyanide solubility tests, and bottle roll tests on exploration drill cuttings samples; and those results plus column leach test data on diamond drill core or bulk ore composites. Subsequent larger scale heap leach test data can then be compared to the historical data base, to blast hole composite data during mining, and eventually to production data. This paper does not discuss metallurgical comparisons between assays, cyanide solubility tests, and bottle roll tests on exploration drill cuttings samples, but does discuss metallurgical comparisons from bottle roll tests, laboratory scale column leach tests, and pilot scale heap leach tests on core and bulk ore samples with operating data for three U.S. commercially producing heap leach operations. Provided that representative core or bulk samples are used for evaluation, heap leach test results accurately predict or understate the success of the commercial operation and remove most of the uncertainty from the investment decision.

Jan 1, 1990

By Michael H. Vallez

On September 13, 1973 MAPCO Inc. leased from Pocahontas Land Corporation an 18,000 acre tract of coal lands in Eastern Kentucky's Martin County (See Figure 1.). In July, 1974 initial run of mine coal shipments commenced and in April, 1976 shipments of a 12,500 BTU, less than 1% sulphur, washed coal was being shipped. Results of exploration demonstrated that large quantities of overburden would have to be moved. MAPCO decided to invest in large surface mining equipment to tackle the job.

Jan 1, 1981

By L. Bloom

In 1996, lack of confidence in assaying methods and sample handling affected companies as diverse as Bre-X and Timbuktu. Share prices and the ability to raise financing are impacted when the quality of assay data is suspect. Overseas projects are subject to enhanced scrutiny when local facilities are used that are unfamiliar to brokers, financing agencies and banks. Quality control systems can be implemented but there are associated costs. These costs should reflect the risk to the mining company, investors and financiers and the size of the proposed investment. In this regard, assay control can be considered a form of insurance to enhance the value of an exploration or mining project. Providing reliable assay data in a production laboratory is challenging. Pressures such as time constraints and profitability affect data integrity. In Australia and North America, reliable assaying services have been provided by several laboratories. Mistakes are primarily due to human error but systems are available that monitor results and identify these types of errors. As the mining industry expands globally, mining companies encounter difficulties in some of these areas due to lack of infrastructure, poor communications, bureaucracy and political risk. These challenges also apply to the operation of laboratories, enhancing the risk of compromised data.

Jan 1, 1997

By Ken Deter

My recent experience has been with wet tropical environments, which address a different set of concerns than Nevada, for example. Spraying rather than drips are required in most cases just to assist the water balance requirement, and my comments address those situations. Most tropical operations are faced with both extremely wet and very dry seasons, with some having multiple cycles during the year. A heap leach operation must address the rate of solution building up within the ponds and how long the volume must last until the next rainy season. It may be easier to construct sufficient pond volume to permit yearlong operation than by discharging excess solution now, and searching for water later. Pond capacity requirements can help with the following: Consider using the solution that could be locked up in the pads during leaching to assist water balance problems. Spray excess solution continuously onto spent ore that would not be normally be sprayed again to "soak up" the excess solution, and stop spraying when the water balance is low, allowing the solution in the spent ore to return back into the system-with or without cyanide added. In a multiple lift system, if intermediate HDPE liners are planned for solution grade control, have drips placed before the HPDE liner is in place. The drips can distribute excess precipitation throughout the lower lifts to control the water balance, while the most current lifts are being leached and sent directly for the preg pond. With only 2 million tonnes (2.2 million tons) of spent ore involved, up to 200,000 cubic meters (53 million gallons) of solution could be moved into or out of the water balance system, if proper methods are designed and installed. That is equivalent to one meter (40 inches) precipitation falling on a 200,000 square meter (2.2 million square feet) pad area. You may even get a little bit more gold recovered as the solution drains from the earlier pads, as well.

Jan 1, 1999

In 1991, US mine production of barite decreased 3.4%. Barite consumption, sold or used by grinding plants, decreased by 11.7%. Imports also decreased by 15.4% over 1990. World mine production increased I%, according to the US Bureau of Mines. The value of domestically produced barite, f.o.b. mine, increased 3.3% according to the Bureau. The declared value c.i.f. US port of all imported crude barite during 1991 increased from $40.61/t ($36.84/st) in 1990 to $42.35/t ($38.42/st), the Bureau stated. Nevada was the leading producer of barite with 78% of the total, followed by Georgia and Missouri. It is estimated that 75% of the domestically mined barite was used as a weighting agent in drilling fluids. The remaining 25% was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia and Tennessee was used in the non-oilfield sector. Of the total barite used by grinding plants and chemical manufacturers, it is estimated that 93% was used in drilling fluids. The remaining 7% was in the non-oilfield sector, including barium chemicals and fillers in paper, plastics and glass. Tonnage consumed in the drilling fluids market decreased due to the lower average rig count during 1990. The average number of rotary rigs operating was 860. That was 14.9% less than the 1990 average of 1010 in the US. Crude barite imports were 138 kt (152,000 st) less than 1990 or 15.4%. Imports accounted for 70% of the (ap¬parent) barite consumed in the US. During 1991, China continued to be the leading exporter of crude barite ore to the US with 85.1 %. India followed with 14.8%. About 97.5% of the imported barite ore was used in the oilfield sector. Ground barite imports decreased from 56.7 to 46.2 kt (62,500 to 51,000 st) 1991. Mexico was a major exporter to the US, accounting for 75.3% of the total ground barite imports. Canada shipped 23.7%, while other countries accounted for less than 1 %, primarily for the nonoilfield market. During 1991, the number of grinding plants supplying the drilling fluids market along the Gulf Coast was reduced from 12 to 10. Baroid Drilling Fluids completed its mining program at the Rossi Mine near Dunphy, NV.

Jan 1, 1992

By Charles D. Litton, Ronald S. Conti

This report describes the results of research conducted in the Bureau of Mines Experimental Mine at Lake Lynn Laboratory to determine the effects of air velocity, sensor spacing, and stratification of CO levels on the detection of slowly-developing coal/conveyor belt fires. In general, the time to detect a developing fire is calculated assuming an average CO level that has mixed completely with the ventilated airflow. The data indicate that CO sensors placed near the roof of an entry take advantage of buoyant- induced stratification of combustion products, resulting in earlier detection of developing fires. Even during the low-temperature, smoldering stage of a fire, the combustion products will tend to stratify near the roof, and once flaming occurs, the degree of stratification increases markedly. As one would expect, at higher air velocities, the degree of stratification is less than at lower air velocities, although still significant, especially during the flaming stages of the fire

Jan 1, 1993

By S. Frimpong, N. Demirel

Overburden excavation is an integral component of the surface mine production chain. The walking dragline is the most economic production equipment for overburden excavation in strip mining. Draglines are capital intensive, and thus, investments in multiple units severely impact the economic viability of projects. The use of few dragline units results in highly concentrated production focus, which must be efficiently managed to derive the potential economic benefits. Efficient use of draglines requires a thorough knowledge of the powered functions, the 3D rotational and translational motions and machine-formation interactions within the operating environment. Dragline kinematics and dynamics are required to understand and characterize machine performance and efficiency. In order to sustain the high productivity in difficult operating conditions, the dynamics of the dragline must be modeled and analyzed based on comprehensive kinematics. This paper investigates the planar kinematics of the front-end assembly and its interactions with the formation during excavation using the “Vector Loop Analysis” formulation with comprehensive simulation modeling in MATLAB Simulink. The kinematic models are used to examine the translational, rotational and angular displacement, velocity and acceleration components of the dragline front-end assembly along defined bucket trajectories during excavation. The results are the precursors for comprehensive modeling to examine the load deformation, torque requirements and dragline stress loading profiles for improving machine health and longevity.

Jan 1, 2006

By David A. Holmes

Zeolites are crystalline, hydrated aluminosilicates of the alkali and alkaline-earth metals. Their crystalline framework is based on a three dimensional network of SiO4 tetrahedra with all four oxygens shared by adjacent tetrahedra. The alkali and alkaline-earth cations are loosely bound within this framework structure and may be exchanged, to varying degrees, with other cations or molecular water. Most zeolites can be reversibly dehydrated. At present, close to 40 natural zeolite minerals have been identified and over 100 zeolites have been synthesized. Zeolites are a family of hydrous aluminosilicate minerals whose physical properties provide unique features for a wide variety of practical applications. Zeolites have been known for more than 200 years, but it was not until the middle of this century that their economic potential and widespread occurrence in sedimentary rocks were known. Since 1950, literally thousands of articles and patents have appeared in technical literature, and commercial pro¬duction of natural zeolites may now exceed 1 Mt worldwide an¬nually. In the past 40 years, the zeolite mineral group has changed from that of a museum curiosity to one of an established industrial mineral commodity. According to Breck (1974), zeolites are characterized by the following properties: 1) High degree of hydration, 2) Low density and large void volume when dehydrated, 3) Stability of the crystal structure of many zeolites when dehydrated, 4) Cation exchange properties, 5) Uniform molecular-sized channels in the dehydrated crys¬tals, 6) Ability to adsorb gases and vapors, 7) Catalytic properties. All zeolites are molecular sieves, but not all molecular sieves are zeolites. Activated carbon, activated clays, alumina powder, and silica gels are also molecular sieves. Molecular sieves are materials that can selectively adsorb molecules on the basis of their size, shape, or electrical charge (Clifton, 1987). Commercial application of zeolites is based on the following physical properties: molecular sieving, ion exchange, adsorption, and catalysis. Potential commercial utilization includes hundreds of possible applications. The principal uses at this time, however, are as fol¬lows: -Ammonium-ion removal in waste stream treatment, sewage treat¬ment, pet litter, and aquaculture, -Odor control, -Heavy metal ion removal from nuclear, mine and industrial wastes, -Agricultural use, such as soil conditioner and animal feed supplement. An estimated 800 kt to 1 Mt of natural zeolites were produced and consumed worldwide in 1991. Eight small operators reported collective production and consumption of an estimated 18 kt of natural zeolites in the United States during 1991, mostly for feed additives and for odor control, aquacultural, agricultural, catalytic, and ion exchange applications (Eyde, 1992).

Jan 1, 1994