Search Documents

By Michael S. Robinson, Serge Moalli

Construction of the CSO Retention - Treatment Tunnel, Segment 1 in Dearborn, Michigan includes excavation for an overflow Structure with a minimum inside diameter of 15.24 m (finished). The excavation extends downward through overburden soil including a 15.2 m thick zone of potentially weak clay. This paper presents the subsurface data for the clay and a geotechnical analysis thereof, together with predictions of the behavior of the planned 15.54 m inside diameter open end caisson as it is sunk through this potentially weak zone. In a companion paper, the writers will compare the behavior observed with that predicted.

Jan 1, 1995

By Thomas J. Lien

AMAX Coal Company has constructed the first commercial demonstration sub-bituminous coal dryer at its Belle Ayr Mine south of Gillette, Wyoming. This 215 ton per hour facility is projected to produce 165 tons per hour of dried coal at 10 percent moisture and 10,800 Btulpound (6,000 KCIkg). Approximately 43 tons per hour of water will be removed from the coal and seven tons per hour of coal burned as fuel.

Jan 1, 1989

By D. D. Misra

The paper presents a computer simulation package developed for the size¬-reduction circuits of Indian hematitic iron ores. The package is developed by linking independent procedures describing different unit operations like crushing, screening, recycling, etc. Mathematical models are used to quantify the unit operations involved. The models are selected after thorough analytical studies of the samples and data collected from four operating plants. The package developed gives a fairly accurate result with respect to, size and chemical composition of the flow stream and products. The program written in PASCAL can be used to try the flowsheet with various raw ores, as well as different flowsheets with the same raw ore.

Jan 1, 1989

By L. G. Austin

Equations are derived to allow for different mean velocities of axial flow for different sizes of particles in fully mixed ball mills. The equations are modified to allow for the exit classification that occurs in grate-discharge autogenous and semiautogenous tumbling mills. An approximate treatment is given that applies for other forms of residence time distribution, provided that the mill contents are close to fully mixed.

Jan 1, 2000

By Suresh K. Bhatt

Appalachian coalfields have been the predominant source of quality coals since the inception of commercial mining in the United States. In a broad sense, Appalachian coalfields can be considered those east of the Mississippi River, representing about 55% of total US coal production. In this special feature on Appalachia in MINING ENGINEERING, emphasis is given to the four coal-producing states of Pennsylvania, West Virginia, Virginia and (eastern) Kentucky. These four states produce more than 90% of the coal from the total Appalachian region, or about 40% of the total US coal production. Historically, Appalachia has been the principal source of coal for domestic industries and for export. There have been numerous fluctuations in the Appalachian coal industry during the past 20 years. Appalachia was affected by cyclical and structural changes in various industries, particularly the US steel industry, and changing world coal markets. It was also the region of more mine worker labor stoppages than other parts of the country. In general, the factors that affected Appalachian coal production over time are identical to those that determined changes in coal production nationally.

Jan 1, 1995

By Ron L. Schmiermund

The Ferris-Haggarty underground mine was abandoned circa 1910, and portal discharge has since resulted in degradation of a trout fishery in the receiving waters of Haggarty Creek. Although tunnel discharge varies dramatically in volume throughout the year due to infiltration of snowmelt, compositionally it is a nearly constant low-TDS, pH-neutral, low-sulfate, copper-silicate dominated water. Between infiltration events, components of ARD accumulate in unsaturated, oxygenated environments within upper workings and are delivered to the main haulage level by the subsequent annual snowmelt flush. Mixing with non-ARD mine waters results in neutralization, dilution, and precipitation of amorphous copper carbonate and silicate phases. These mechanisms, combined with variations in the water balance, control the composition of the portal discharge. Understanding the chemical and hydrologic control mechanisms was critical to the design of a passive treatment system to decrease effluent copper concentrations.

Jan 1, 2000

By Jack E. Fraley, Robert E. Simpson

INTRODUCTION Spokane Mining Research Center (BuMines) is researching sealants for underground coal mines to: 1. Reduce sloughing of shale roofs. 2. Reduce sloughing of coal ribs. 3. Seal block stoppings against air losses. 4. Construct stoppings by spraying over jute cloth or metal lath. 5. Render incombustible in-place polyurethane foam. Originally the work was directed towards reducing sloughing of shale roofs. Many underground coal mines have shale directly over the coal which weathers severely after exposure to the mine atmosphere. Lab investigations(l, 2, 3, 4) have shown that many shales separate into layers when immersed in water or stored in a high relative humidity environment. Upon drying or after removal from high humidity, the shales continue to separate. Underground coal mines become wet in the warmer months from condensation of the ventilating air. Conversely, the mines become dry in the cooler months from evaporation. The mines experience severe shale break-up during the summer and much less break-up during the winter. Figs. 1, 2 and 3 show weathered shale roofs. in underground coal mines. Fig. 4 shows fallen shale on the entry floor. Sealing the shale reduces this sloughing problem.

Jan 1, 1974

By John C. Edwards, F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center's Safety Research Coal Mine (SRCM) to determine products-of combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were con- ducted in a 180 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.1 3, and 0.06 m/s were determined at 30, 60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.

Jan 1, 1997

By K. G. Sutterer, P. T. Wang, R. Sweigard

One possible alternative for the disposal of flue gas desulfurization (FGD) by-products is to use it as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation in stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48% and the peak stress could be decreased by about 58%. The study indicates that fairly weak FGD materials can eventually lead to the stability of backfilled highwall adits.

Jan 1, 1998

By George Bárdossy

Most of the bauxite deposits in Europe belong to the karst type. They are located mainly ill Southern Europe along the Mediterranean Sea and in the Ural Mountains. Lateritic bauxite deposits occur on the Russian Platform, in Poland, Northern Ireland and in Turkey. Tikhvin-type deposits arc found on the Russian Platform. Bauxite formation in Europe started in the Middle Devonian. The main bauxite forming period was the Upper Cretaceous. Very few bauxites are younger than Eocene. Most deposits are covered by overburden of up to 1000 m. Prospecting is carried out by drilling. Several geophysical methods are used to detect the hidden deposits. Geostatistical methods were introduced in several countries for evaluation of the reserves and the geometry of the deposits. Data on bauxite production are given for 1982 and since the beginning of mining in Europe.

Jan 1, 1984

By Wayne Stange

Due to the availability of user-friendly microcomputer based packages, the use of simulation is increasing.. Users have however encountered problems inherent to the structure of sequential-modular simulators. These are the difficulties associated with estimating parameters for arbitrary' models and the solution of design and optimization problems. The implementation of an optimization routine in the simulator MicroSim has facilitated the solution of such problems. The literature indicates that more efficient numerical techniques for solving optimization problems than those presently used in MicroSim are available. These techniques, together with user-interfaces which allow such problems to be specified easily by users, will result in the development of simulators much more powerful than existing ones.

Jan 1, 1989

By Frank F. Aplan, Robert S. Thomson

A placer ore jig, typically used to recover fine gold, tin and diamonds from alluvial ores, has been modified to remove fine pyrite from minus 6.4 mm (-114 inch) coal. In parallel tests, it proved to be far superior to two conventional coal jigs, the Baum and the Baum-feldspar, in removing fine pyrite from coal. The Pan-Am placer jig was found to remove essentially all of the +28 mesh pyrite and from 99% to 90%, decreasingly, in the 28 to 200 mesh range. This jig also showed a superior performance to the Baum-Type jigs in removing fine coal from its associated refuse. The superiority of the Pan-Am placer jig is related to the strong emphasis given on the suction stroke and, hence, on consolidation trickling, whereas the Baum jigs principally emphasize the pulsion stroke during jigging.

Jan 1, 1995

By V. McLemore

New Mexico ranks 2nd in uranium reserves in the U. S., which amounts to 15 million tons ore at 0.277% U3O8 (84 million lbs U3O8) at $30/lb (EIA, 2006). The most important deposit in the state is sandstone within the Morrison Formation (Jurassic) in the Grants district. More than 340 million pounds of U3O8 have been produced from these deposits from 1948-2002, accounting for 97% of the total production in New Mexico and more than 30% of the total production in the United States. Sandstone uranium deposits are defined as epigenetic concentrations of uranium in fluvial, lacustrine, and deltaic sandstones. Three types of sandstone uranium deposits are recognized: tabular (primary, trend, blanket, black-band), roll-front (redistributed, post-fault, secondary), and fault-related (redistributed, stack, post-fault). Several companies are planning to mine these deposits by in-situ leaching.

Jan 1, 2007

By Joseph M. Denk, John N. Baran, William J. Francart

Filling or sealing shafts of underground coal mines is required when the mine is declared inactive by the operator, permanently closed or abandoned for a period of time greater than 90 days. Although shaft filling requires the use of incombustible materials for the first fifty feet of the shaft, a sparking potential may exist which has been reported to be the cause in at least one shaft-filling explosion. This paper outlines the method used at the explosion site to monitor mine gases within the shaft to assure the safety of the workers involved in the remainder of the shaft-filling operations. Gases which were monitored include methane, oxygen, carbon monoxide and carbon dioxide. Continuous sampling was conducted twenty-four hours per day to determine the methane liberation and accumulation of gases within the shaft. Once gas concentrations were evaluated, the need for ventilation in the shaft was obvious because methane accumulations within the shaft were in the explosive range. Several methods to ventilate the shaft were explored. The most practical seemed to be the dilution of gas concentrations with compressed air to inject a quantity of fresh air into the shaft. But, when the compressed air was stopped, a buildup of an explosive mixture reoccurred. The pattern of gas accumulation was then studied to find the correct combination of ventilation and shaft-filling time periods which would a1 low for the greatest reduction of the potential for an explosion. Gas concentration sampling continued during the remainder of shaft-filling operations at this shaft and four others at the same mine. In conclusion, this paper illustrates some of the problems which are often overlooked in a shaft-filling operation. If addressed, the work can be done in a safe and feasible manner.

Jan 1, 1987

By S. Finsterle, R. C. Trautz

Numerical modeling studies were performed to investigate water seepage into underground openings excavated in unsaturated fractured rock. Water seepage is an important factor affecting the performance of a nuclear waste repository, such as the one proposed at Yucca Mountain, NV. The amount of water dripping into an underground opening depends on the connectivity and permeability of the fracture network, as well as on the capillarity of individual fractures intersecting the opening. A high-resolution numerical model of an unsaturated fracture network was developed, and the appropriateness of seepage predictions using a fracture-continuum model was examined. Model calibrations to liquid-release tests performed at Yucca Mountain are also discussed.

Jan 1, 2002

By J. Wagner, P. Eger, G. Melchert

In 1991, LTV Steel Mining decided to close an open-pit taconite mine in northeastern Minnesota using a passive-treatment approach consisting of limiting infiltration into the stockpiles and wetland treatment to remove metals. More than 50 Aft (55 million st) of sulfide-containing waste had been stockpiled adjacent to the mine during its 30 years of operation. Drainage from the stockpiles contained elevated levels of copper, nickel, cobalt and zinc. Nickel is the major trace metal in the drainages. Before the closure, the annual median concentrations ranged from 1.5 to 50 mg/L. Copper, cobalt and zinc are also present but they are generally less than 5% of the nickel values. Median pH levels range from 5 to 7.5, but most of the stockpile drainages have pH levels greater than 6.5. Based on the chemical composition of each stockpile, a cover material was selected. The higher the potential that a stockpile had to produce acid drainage, the lower the permeability of the capping material required Covers ranged from overburden soil removed at the mine to a flexible plastic liner. Predictions of the reduction in infiltration ranged from 40% for the native soil to more than 90% for the plastic liner. Five constructed wetlands have been installed since 1992. They have removed 60% to 90% of the nickel in the drainages. Total capital costs for all the infiltration reduction and wetlands exceeded $6.5 million, but maintenance costs are less than 1 % of those for an active treatment plant. Because mine-drainage problems can continue for more than 100 years, the lower annual operating costs should pay for the construction of the wetland-treatment systems within seven years.

Jan 1, 2000

By B. Cristol, G. Benier

Laboratory and pilot tests have shown that the grinding of some aluminas makes two populations appear : agglomerates’ and ultimate crystals’. Classical breakage functions (Size Mass Balance Method) aren't able to describe correctly this kind of grinding. So we have optimized a particular breakage matrix which takes into account the fact that the agglomerates can either be reduced in size or either be blown up to liberate the ultimate crystals. The models which were developed using this breakage matrix are in good agreement with the experimental results of the pilot tests. The industrial breakage functions were estimated from pilot breakage functions, using scale up prediction procedures and plant tests. The agreement between predicted and actual plant performance is excel1ent.A 20 % increase in capacity was predicted to be available by improving the grinding circuit classifier performances.

Jan 1, 1992

By J. H. Kempton, D. Atkins, W. Locke

The scrutiny given to model predictions of pit-lake water quality has focused attention on the uncertainty associated with long-term predictions. Although comparison of probabilistic predictive modeling of water quality in existing pit lakes suggest that short-term predictions can bracket most parameters, un¬certainties in wall-rock reactions and the stability of groundwater composition and climate remain unquantified This overview of the uncertainties associated with longer-term predictions is presented as support for those considering policy decisions that must be made in the absence of reliable estimates of future conditions.

Jan 1, 2000

By M. Karmis

The algorithms for the mathematical modeling to predict productivity of underground room-and-pillar mining systems are well known and documented. These algorithms consider the time-varying relationships between mining equipment for a given geometty of operations as well as other constraints. This paper presents WebConSim, a newly developed, Web-based, user-friendly computer simulation tool for the Windows environment. The simulator is easily customized for use by field engineers, planning engineers and management and will help mine operators plan the optimum mining sequence for different mine geometrie and equipment layouts. Program output includes production data and equipment utilization indices, as well as time driven event chains that can be used for virtual reality presentations.

Jan 1, 2002

By John T. Gormley, Pressley L. Campbell, Harry L. Crouse

INTRODUCTION This paper summarizes an investigation conducted to determine the relationship, if any, between reported occurrences of abnormal levels of carbon dioxide (C02) gas and the construction of a 2.44meter diameter main sewer tunnel under South Eighty-Fourth Street, West Allis, Milwaukee, Wisconsin. Specific objectives of the study were to determine: (1) the sources of C02, (2) the significance of each C02 source, (3) how C02 could move to areas where it was reported to occur in abnormal concentrations, and (4) what actions could be implemented to eliminate elevated C02 levels associated with the tunneling operation. To accomplish study objectives, expertise from several scientific and engineering disciplines was required including chemistry, geochemistry, microbiology, hydraulics, and hydrology. Pertinent documents were reviewed and field data pertaining to each aspect of the study were collected as required and examined to evaluate existing conditions. Background On or about February 1, 1971, gas with a composition different from normal atmospheric air was reported to enter basements and wells of residences in the vicinity of South Eighty-Fourth Street, West Allis, Wisconsin. Examination of the gas composition revealed that it possessed an elevated concentration of C02 and a depleted concentration of oxygen (02). Public health officials who investigated the appearance of the objectionable gas concluded within reasonable certainty that the elevated C02 concentrations were associated with the tunnel construction under Eighty-Fourth Street.

Jan 1, 1979