Search Documents

By Jung-Hum Lee, Young-Joon Lee, Eui-Joon Hong, Seon-Hong Kim, Chan-Dong Kim, Keon-Woong Jeong, Ki-Lim Kim

"Subsea tunnel needs to be built over 50km long to connect between nations and continents. However there are only 19 tunnels longer than 5km in Korea, and there is no history of constructing and operating a tunnel longer than 50km. As the concept of a subsea tunnel, which withstands high water pressure and has an extremely long length is completely different from that of a land tunnel, all kinds of the latest technologies for tunnel construction are required such as survey and analysis of geology, design and construction under high water pressure, ventilation and prevention of disasters within an ultra long tunnel. Therefore, this paper describes the determination of tunnel cross-section under a high speed railway, structural stability, ventilation and fire safety under construction and operation, etc. through the virtual project for the length of 108km subsea tunnel under high water pressure of maximum 20bars from Honam to Jeju island in Korea. 1. INTRODUCTION The Honam-Jeju virtual project is subsea tunnel project to link from Honam(land) to Jeju(island) extending the currently operating Honam high speed railway line, and the same express train(t=18, design speed 350km/h, total train length 200m) operating at Honam line is applied in this project. As Honam-Jeju site is approximately 80km in straight distance with 160m maximum depth, subsea tunnel project should determine the various issues such as air quality/ventilation, aerodynamics, temperature, drainage, fire & life safety, structural stability. Figure 1. is the plan of subsea tunnel, with be constructed using Shield TBM. This double tube-Single track is composed of cross passages (every 350m in general section and 40m in emergency station), service tunnel, pressure relief ducts (every 250m), cross-over tunnels, shafts and emergency stations. 2. ALIGNMENT AND SITE CONDITON This project is planned as an ultra long tunnel of total length more than 105km via existing islands between Honam and Jeju island because straight alignment requires an artificial island which has high cost and construction risk, by deep water depth, though this is the shortest distance (see Fig 2). Water depth and topography in project site is divided into two blocks by Chuja Island. In first block to Chuja Island, depth of the water is 40m on average and maximum 60m, which indicates gradual change of water depth relatively. Also, outcrop bedrock is widely distributed near island."

Jan 1, 2016

By Akram Marseet, Andrew J. Petruska, Rik Banerjee

Event cameras are used for their performance in high dynamic-range lighting conditions which are canonical to active mining environments. Direct labeling of event-based image data to train a model to perform semantic segmentation using traditional methods is slow and error-prone. This study proposes a framework to use roughly hand-labeled color images from a mine as an input to an intermediary probabilistic algorithm called alphamatting to generate a ground-truth data set. These high-fidelity labels can be used to train a semantic segmentation model to differentiate the support strap from the roof. This model can then be leveraged to segment an event-based scene to enable autonomous roof bolting. This pipeline has been shown to achieve an accuracy of 88% with a false positive rate of 3%.

Feb 1, 2024

By V. Steinbach

Non-renewable mineral raw materials are grouped into three categories to investigate ways leading to sustainable use of natural resources: 1.) metallic resources, 2.) non-metallic resources with the exception of the fertilizer minerals, and 3) the fertilizer minerals for the nutrients nitrogen (N), potassium (K), and phosphorous (P). With the exception of minerals in Group 3 which are essential for plant growth, mankind does not need raw materials as such, only the intrinsic property of a material that fulfils a useful function. This is especially true for non-metallic materials. Metallic resources have the best chance to become renewable if one makes optimal use of the resources of the man-made technosphere. For the fertilizer elements K and N there does not exist a problem, because sea water or air respectively provide an inexhaustible source for them. This does not apply to P however. So P is serving as one of our apposite case studies for solving sustainability challenges. For all the challenges along the road from a non-sustainable to a sustainable resource economy technology can be envisioned to come to the rescue provided conditions that are considered to be essential for sustainable use for all natural resources-- affordable renewable energy and human ingenuity to find new solutions for functions, to optimize processes and to minimize losses-- are satisfied.

Jan 1, 2011

By L. Yuan, J. H. Rowland, D. Bahrami, R. Thomas

Blasting is the main method of production in many non-coal underground mining operations and produces multiple toxic gases as a result. The Mine Safety and Health Administration (MSHA) requires mine operators to measure the level of toxic gases in mines as frequently as necessary to ensure they are below regulatory safety limits. The current practice uses portable gas monitors to check the concentrations of toxic gases after a fixed post-blast time. This paper studies the application of a gas monitoring system in the return entry of a limestone mine to determine a safe re-entry time. The National Institute for Occupational Safety and Health (NIOSH) conducted such a monitoring program in a limestone mine from September 2016 through May 2018. NIOSH/PMRD (Pittsburgh Mining Research Division) is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions. This study showed that the use of gas monitoring in the return air can be a useful tool at the mine operator’s disposal to detect and reduce the risk of hazardous conditions and also to reliably estimate the re-entry time.

By K. C. Corin, B. McFadzean, J. G. Wiese

The Bushveld Complex of South Africa contains almost 90% of the world’s reserves of platinum group minerals (PGMs). In the flotation of PGMs, there are significant challenges arising from the need to treat ever-decreasing grades of the relevant ore deposits. The major challenge in the flotation of these ore bodies is the control and management of the gangue minerals, particularly silicates such as orthopyroxene and plagioclase feldspar which are often rimmed with talc which makes them naturally floatable. It has been shown that various polysaccharide depressants such as CMC and guar have different properties in terms of depressing the gangue minerals. Since the PGMs are often associated with sulphides, copper sulphate is widely used as an activator in PGM flotation but can inadvertently activate the gangue minerals and reduce the recovery of PtTe2 which accounts for up to 40% of the Pt in the Platreef ore body. Depressants also reduce the mass of solids reporting to the froth and can thus destabilize the froth. This effect on the froth can be mitigated by using higher frother dosages or water of higher ionic strength. In summary due care needs to be taken to carry out site test work to develop an optimum ratio of collector, frother, activator and depressant to ensure that the highest grades and recoveries of the PGEs are obtained while reducing depressant dosage as much as possible. Chromite recoveries can be reduced through the application of gravity separation or reducing entrainment through reduced water recovery. INTRODUCTION The Bushveld Complex located in the north of South Africa contains the world’s largest deposit of Platinum Group Minerals (PGMs) (1). The so-called upper Critical Zone of the Complex hosts the largest concentration of platinum group elements (PGEs) in the world. The Zone hosts the Upper Group Chromitite No.2 (UG2) reef and Merensky Reef as well as the Platreef mineralization of the northern limb of the Bushveld Complex. The Merensky pegmatoid Zone contains the base metal sulphide grains and associated PGMs. Of particular importance to the topic of this paper is the occurrence in these reefs of various gangue minerals. The Merensky Reef consists predominantly of orthopyroxene (~60%), plagioclase feldspar (~20%), pyroxene (~15%), phlogopite (5%) and occasional olivine. Secondary minerals such as talc, serpentine, chlorite and magnetite have widespread occurrence. Of these, talc is the only mineral to show significant natural floatability (2,3). Although present in small amounts talc is closely associated with pyroxene and imparts significant floatablity to the high concentrations of pyroxene present in these ores (4). The base metal sulphides consist predominantly of pyrrohtite (~40%), pentlandite (~30%) and chalcopyrite (~15%). The major platinum group minerals are cooperite (PtS), braggite [(Pt,Pd)NiS], sperrylite (PtAs2) and PGE alloys. The UG2 consists predominantly of chromite (between 60 – 90% by volume) with lesser silicate minerals (5 – 30% pyroxene and 1 – 10% plagioclase). Other minerals present in minor concentrations, can include silicates, oxides and base metal sulphides. Total PGE varies by locality but on average range between 4 and 7 g/t. The PGMs present in the UG2 Reef are highly variable, but generally the UG2 is characterised by PGE sulphides such as laurite (RuS2), cooperite (PtS) and braggite [(Pt,Pd)NiS. The base metal sulphides consist predominantly of chalcopyrite, pentlandite and pyrrhotite. The Platreef is located in the northern limb of the Bushveld Complex. This reef consists of a complex assemblage of rock types, with pyroxenites, serpentinites and calc-silicates being the most abundant. Base metal mineralization and platinum group element (PGE) concentrations are found to be highly irregular, both in value as well as in distribution. The predominant platinum group minerals (PGM) in the mined area of the Platreef are the PGE tellurides, alloys, arsenides and sulphides. T

Jan 1, 2019

By Peter N. Calder

The selection of a slope angle for an open pit in rock has often been made without the benefit of a comprehensive engineering study. This is largely due to the fact that the hardware and procedures necessary for such a study have not been available. Recently this situation has been reversed. The application of borehole television and terrestrial photogrammetric devices has made possible the accurate determination of rock joint structure, on which stability calculations can be based. Another important aspect is the evolution of practical methods of conducting in-situ rock joint strength tests.

Jan 1, 1971

By T. Seal

Hydro-Jex© releaching was undertaken during the summer of 2010 at the Valley Leach Facility (VLF) at AngloGold Ashanti?s Cripple Creek & Victor Gold Mine. Several advancements to the technique were made in response to the technical design and operational challenges posed by the unique site conditions. New geophysical resistivity monitoring techniques were developed to monitor solution migration during the injections. These developments are presented along with discussion of gold production resulting from the project.

Jan 1, 2011

By R. Hiebert, M. Canty, S. Beckman

An innovative biological process is described for the treatment of cyanide-, metals- and nitrate-contaminated mine process water. The technology was tested for its ability to detoxify cyanide and nitrate and to immobilize metals in wastewater from agitation cyanide leaching. A pilot-scale demonstration is described in which a pilot plant was constructed to demonstrate the technology on a mine process-waste stream at a mine in Nevada. The demonstration was performed jointly under the Mine Waste Technology Program (MWTP), funded by the US Environmental Protection Agency (EPA) and jointly administered by the US De¬partment of Energy's (DOE) Western Environmental Technology Office (WETO) under Interagency Agree¬ment Number DW89938513-01-0. The Superfund Innovative Technology Evaluation (SITE) demonstration program was also involved in the project. MSE Technology Applications Inc. (MSE), Butte, MT, was the contractor responsible for conducting the project, and Pintail Systems Inc., Aurora, CO, was the technology provider. The pilot-scale unit was field-tested at Echo Bay's McCoy/Cove Mine southwest of Battle Mountain, NV. The biotreatment process was considered successful in destroying cyanide in the mine process water. The process was also determined to be effective in removing metals. The pH was consistently neutralized and nitrates were successfully removed from the mine process water. From the results of these pilot-scale tests, it was concluded that the biotreatment process potentially of¬fers an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 2000

By L. B. Hales

December 3, 1972, James Wm. White presented the results of an instrumentation and process control survey which was sponsored by the Anaconda Company at the annual Tucson Subsection AIME meeting.(1) Twenty-six responses were obtained from questionnaires sent to 48 operating plants throughout the world. The survey results were discouraging in that there were more failures and problems than examples of success. The following quotes are taken from the text of the paper. "We run our mill by the seat of our pants." 'If these blue sky Ph.D.'s (in the instruments and controls area within research) had some operating experience they wouldn't make a lot of the suggestions they do."

Jan 1, 1981

By John L. Shafer

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in-situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent "leachability" of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corporation (ORC), the corporate R&D for Occidental Petroleum has under-taken a modest effort to address the question of "how to best identify and determine the information necessary to predict and control the operation of an in-situ leach for the economic recovery of copper."

Jan 1, 1977

By Paavo Eerola

In May of 1984, it was decided that Outokumpu Oy would design and build a new nickel flotation mill to process ore from the newly discovered Enonkoski mine in eastern Finland. Since there hart peen a number of successful process charges in the existing mills, the design effort included the study and incorporation of several new developments, including all-autogenous grinding, "flash flotation", lane cell roughing, large cell cleaning and a computer-based, profit optimizing, process control system. The paper discusses the background and results of those studies, and a description of the resulting mill which will begin production in 1986.

Jan 1, 1985

By George Innes

The soda ash business in the United States has undergone a sweeping technological change in ihe last 20 years. In a world where synthetics are continuzlly replacing natural products, here we have exactly the opposite, a syntheric chemical being replaced by a natural product. This change is nearly complete in the U.S. and is beginning to take place in Europe and other parts of the world.

Jan 1, 1980

By Shawn Collins

BACKGROUND The history of the Pine Point Mine is a rich one. This property once boasted one of the largest and most profitable lead-zinc mines in Canada's long and storied mining history. The Pine Point mine used open pit technology to extract the ore, but they faced several challenges. In addition to logistics problems with haul distances and metal prices, the mine faced the challenge of a large in flow of water from the Great Slave Lake. Eventually, the Pine Point Mine was closed leaving behind a large deposit of lead-zinc ore. Following the closing of the Pint Point Mine, Tamerlane Ventures Inc. acquired this property which includes approximately 70 million tonnes of lead-zinc reserves. The initial phase of this project will concentrate on the R-190 deposit as a test site to prove their new approach for extracting the ore. The R-190 reserve is believed to have approximately 1,014,000 million tonnes of high grade ore varying from 5% to 52% combined lead-zinc. Once the pilot project proves the approach is valid, the process will be repeated in approximately 33 other ore bodies on the property. This paper is written to discuss the design process to determine the most effective means of placing production and service equipment in the same shaft. Currently the design work and the mining scheme is complete, but lead-zinc pricing has prevented Tamerlane Ventures Inc. from moving forward with the project.

By T. Cyrul

The Polish underground mining has its long lasting tradition. High production of coal, that has recently been approaching 200 milion tons per year, put this small country among the bigest world producers of coal. To achieve such a high production, which mainly originate from very unfavourable mining and geological conditions, Polish scientists and engineers have to introduce new and original solutions to the mining practice. Many of the solutions on mining methods, ventilation, stability, subsidence etc., have had the world wide reputation, however, insufficient translations from Polish cause , that many of the recent Polish mining achievements are not known to foreign specialists.

Jan 1, 1986

By Raymond E. Zimmerman

The cleaning of coal by the use of jigs is one of the oldest methods of separating coal from its impurities. Although in many situations jigs have been replaced by other methods, by far the largest percentage of coal today is still being cleaned by some form of jigs. Some piston- or plunger-type jigs are still in use throughout the world; however, the greater number are air pulsated, generally called the Baum jig, named after the original inventor, Fritz Baum of Germany. This standard jig, with slight modifications, has been in use for over 75 years. Up until recently, however, it has had certain limitations in obtaining the high performance and efficiencies required in modern coal preparation practice. TO improve its performance, some radical modifications have been made in its design and operation SO that there is now a Baum-type jig giving much higher performance in terms of capacity, efficiency and sharpness of separation- This new jig is called the Batac, and the purpose of this paper is to describe its characteristics and present data giving its performance in treating coarse and fine sizes of coal.

Jan 1, 1974

By L. Yuan, A. Smith

"NIOSH’s mine fire simulation program, MFIRE, is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines, which has been used by U.S. and international companies to simulate fires for planning and response purposes. MFIRE is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence such as changes in ventilation parameters, external influences such as changes in temperature, and internal influences such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the Bureau of Mines in the 1970s, several updates have been released over the years. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated FORTRAN programming language was replaced with an object-oriented C++ language and packaged into a dynamic link library (DLL). However, the MFIRE 3.0 release made no attempt to change or improve the fire modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of fire source models of the t-squared fire and heat release rate curve data file, the addition of a moving fire source for conveyor belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke rollback phenomena. All the improvements discussed in this paper will be termed as MFIRE 3.1 and released by NIOSH in the near future INTRODUCTION The MFIRE program, originally developed in the 1970s by the U.S. Bureau of Mines (now the Office of Mine Safety and Health Research (OMSHR) at the National Institute for Occupational Safety and Health (NIOSH)) and Michigan Technological University, has been a mainstay in modeling of the mutual influences between a fire and the mine ventilation system during an underground mine fire. Several update versions have been released over the years, including MFIRE 1.27, 1.29, 1.30, 2.0/2.01, 2.10, and 2.20. The MFIRE program logically comprises four parts: (1) a conventional network calculation, where it performs the basic network balancing without considering heat or mass transfer; (2) a temperature calculation to establish the reference temperature distribution before a non-steady state (transient-state) simulation; (3) a transient-state simulation that follows changes in ventilation step-by-step to produce a continuous description of the temperature distribution, smoke, and contaminant spread through the ventilation system during a fire event; and (4) a quasi-equilibrium simulation to predict the state of the ventilation system after a relatively long period of time (defaulted as 5 hours in MFIRE) as the fire reaches a quasi-steady state. In summary, MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions including the influence of natural ventilation, fans, fires, or any combination of these (Chang et al., 1990)."

Jan 1, 2016

By Edward C. Dowling

Cleveland Cliffs and affiliated companies have established a commitment to the development and use of integrated process control. Substantial capital investments in process control, coupled with the dedication of human resources to effectively use the information, have generated meaningful business results. Improvements in productivity, operating costs and product quality have been realized. This paper presents an overall process control and information strategy, specific case studies, lessons learned and the current view of the next steps in the continued journey toward integrated process control and information management.

Jan 1, 2000

By R. Adsero

"In view of the decade long decline in worldwide mine equipment productivity and with heavy economic pressures and survival at risk, improvements for those remaining in the game are essential. The latest Multifactor Productivity data for the US mining industry indicates a continuing descent with Australia on a similar course. The world’s mining industry has a fleet of over 400 large draglines moving billions of tons of material annually. The most efficient use of this equipment resource will provide a competitive advantage to those companies who are committed to improving performance. A dragline monitoring system is a requirement for optimum operations. The monitor reports the facts. Focused actions can change the facts and create improved performance. Analyzing monitor data to build knowledge and create understanding is a beginning. Understanding the key productivity indicators for dragline operations and an effective benchmarking process are the basis for improvement. There is overwhelming evidence that adopting new technologies and concepts including AC drive technology can and will bring about a step change in dragline operating cost with improved production performance.STATE OF THE MINING INDUSTRY A high altitude review of the state of the mining industry provided by a study of multifactor productivity shows a continuation of lower and lower output year on year for the capital and labor inputs applied. The story is sadly similar for both U.S. mining and the Australian mining sector. In fact, according to PwC analysts the worlds mining equipment productivity has declined 20% over the past seven years. (Lumley, 2014) Although the reasons for the continuing decline in mining productivity are varied, the need for improvement is clear. The world’s mining industry fleet of well over 400 large draglines moves billions of tons of overburden and ore (phosphate, limestone, etc.) annually.This discussion will review a few of the tools available for improved productivity in dragline operations."

Jan 1, 2016

By J. R. Dyni

Colorado nahcolite deposits, estimated at 29 billion metric tons, formed in an asp metric permanent-lake basin whose waters were rich in algae and sulfate-reducing bacteria. Nahcolite (NaHCOg) occurs in oil shale of the Green River Formation (Eocene) as aggregates (62 percent), disseminated crystals (24 percent), and impure beds (14 percent). Because much of the nahcolite is nonbedded, it will be mined with oil shale and can be concentrated to marketable grade by crushing and screening Impurities in nahcolite are kerogen, quartz, pyrite, and carbonate minerals. A promising new market for nahcolite is in the process of removal of sulfur dioxide from industrial stack gases. When heated, nahcolite reacts with sulfur dioxide to form sodium sulfate. Differences in thermally induced microporosity may explain why nahcolite is more reactive than trona, a possible competitor with nahcolite for SO2 removal. Limited production of nahcolite at one or possibly two localities is expected in the next several years, but large-scale production is probably at least 10 years away.

Jan 1, 1980

By R. L. Grayson, G. Mishra

Introduction Many old underground mines have been developed extensively into reserves requiring large numbers of workers to maintain and rehabilitate lengthy track haulages and/or belt conveyor systems. Often, large numbers of fans are required to maintain minimal airflows in areas where poor conditions and huge leakages prevail. Problems that beset one such coal mine and projects undertaken to restore it to potential profitability are presented. Brief history The Vesta No. 5 mine was opened in 1908. Drift development began near the Monongahela River, which was the primary avenue for shipping metallurgical coal to coke ovens in Pittsburgh. Over the ensuing 75 years, the main haulage entries were developed a distance of 16.1 km (10 miles) to the present mining area. Track haulage was used to transport coal from working sections to the river loading facility. As haulage distance and areas of high water influx increased, management decided, in 1973, to construct an underground conveyor belt system. The project spanned 36 months and culminated in a system of 22 flights, ranging from 205.7 to 1767.8 m (675 to 5800 ft) long. Six intake and eight return entries were developed as the mains were advanced. These entries provided adequate ventilating capacity over the years, but as extensive gob areas progressed and roof conditions deteriorated, the entries became inaccessible and more resistant to airflow. By 1981, five fans were being used to circulate 943.9 m3/s (555.5 cfm) of air through the mine. An average of 6440 t (7100 st) were produced from 20.8 continuous miner unit shifts and 2.7 longwall unit shifts each day in 1981. The ratio of support to production personnel was 1.94. To maintain the outby 16.1 km (10 miles) of haulage, 110 personnel were used. The average cost per ton was $43.54 ($39.58 per st), resulting in excessive bottom-line losses. The mine possessed a rather promising reserve, mostly in lease, of good quality, medium-sulfur metallurgical coal, but it also had a number of formidable operating problems. Operating problems Contributing factors toward relatively low productivity and high costs were the conditions of the track haulage, conveyor, and ventilation systems. Productivity was affected greatly by downtime associated with the conveyor system, which lacked adequate access for making splices or other repairs. Many areas within the conveyor belt entry itself required more

Jan 3, 1987