Search Documents

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016

By Danqing Gao, Brijes Mishra

Spatial variance of rock properties is an important characteristic of rock which addresses the heterogeneity of mechanical and physical properties and their effect on underground mining. Assessing spatial variance can be useful for both locating potential difficult grounds and performing reliability analysis in the mining support system. This study shows a microscale numerical model for rock material based on continuum mechanics. To consider the spatial correlation factor of mechanical properties in realistic rock mass, this study introduces a spatial correlation concept into the traditional type III extreme value distribution model. Based on the improved microscale random model, we conducted a series of numerical uniaxial compressive tests and one longwall mine model to investigate the progressive failure of rock. The results show that spatial correlation factor can significantly affect the load-deformation curves and fracture patterns. The spatial variance model was applied to a longwall mine that included several cutting sequences to observe the influence of the spatial variance on roof behavior. The cohesion and friction random fields induced failure that propagated randomly through the immediate roof in different entries. The results showed that the spatial variance provides an accurate prediction of erratic roof falls in coal mines.

Jul 20, 2020

By D. Anthony, R. A. Williams, R. Raponi

Barrick Gold Corporation in conjunction with SNC Lavalin Engineers and Constructors have developed basic engineering design for counter current decantation thickener (CCD) plants capable of processing 44 000 t/d. To achieve this throughput in a single train, the largest high-rate thickeners installed to date have been utilized in concert with large process slurry and solution transport systems. Process reliability and plant operability and maintainability have been carefully considered in order to develop a practical, yet cost effective design. The design also incorporates the challenges associated with installation of large equipment and structures in a remote location, with a climatically hostile environment, situated in a high seismic activity zone.

Jan 1, 2002

By J. M. Mutmansky

This paper outlines patterns of methane emission in both longwall and room-and-pillar operations and the effects that these patterns have on the decision as to whether the methane is most economically handled by ventilation alone or by means of a methane drainage system in addition to ventilation. The costs of handling the methane in the ventilation system and the costs of implementing the methane drainage system will be discussed as well as the costs related to the production of coal. The important issue of production slowdowns and gas outs will also be discussed as well as the proper response of mine management to such a situation. Suggestions concerning the keeping of production records related to methane problems will be made as well as justification for more intensive economic analysis of coalbed methane extraction and utilization.

Jan 1, 1998

By K. A. McDonald

Hibernia de Mexico SA de CV, based in Durango, Durango, Mexico built and put into operation a 700-t/d (770-stpd) agitated cyanide leach plant in Guanacevi, Durango. Plant construction began in March 1993 and operations began in November 1993. Hibernia de Mexico, a wholly owned subsidiary of Hibernia Holdings, Inc., is a privately held Tucson, AZ-based company. The startup procedures described here deal with Mexico's legal, import-export and finance requirements, and labor and security requirements. The 700 t/d (770 stpd) Guanacevi project is located next to the town of Guanacevi. The project is an agitated cyanide leach plant built to process about 2 Mt (2.2 million st) of flotation tailings over its life. The plant is operated by Servicios de Guanacevi, Asociasion en Participacion. It is owned jointly by Hibernia de Mexico and Metalurgica Guanacevi SA de CV. Legal, importation of equipment and financing For a foreign company to operate in the mining industry in Mexico, it must form a Mexican company. A Mexican company presently must be at least 51 % owned by a Mexican entity. The other 49% may be owned by non-Mexicans.

Jan 1, 1994

By III Kimball

Mining wastes have received individual attention under the Resource Conservation and Recovery Act (RCRA) since its inception, in recognition of the special characteristics that distinguish mining wastes from other solid wastes. The Environmental Protection Agency (EPA) has recognized that: - Mining wastes are generated in much larger volumes than other industrial wastes. Most material handled in mining is waste (over 99% in many cases) and not marketable product, whereas waste is a small portion of raw materials used in most industries. Consequently, controls used for hazardous wastes may be technically infeasible or economically impractical. - Nearly all mining waste is managed at the site of generation and is land-disposed. . - Mining wastes typically pose lower hazards than other industrial wastes. Mining operations are located predominantly in sparsely populated areas and in arid or semi-arid areas with little surface water runoff and deeper water tables.

Jan 1, 1990

By I. Raposo, I. Moreno-Ventas, A. Palma, M. J. Díaz, M. Vázquez

The oxidative degradation kinetics of chalcopyrite have been studied by thermogravimetric analysis (TGA). The obtained data are necessary for the kinetic description of the flash fusion process, which can contribute to the optimization of the smelting process in copper extractive metallurgy. Activation energy (Ea) evolutions of the involved processes have been determined by several isoconversional methods; in this sense, the chalcopyrite oxidation processes could be adequately described, among studied models (E1641–16, Ozawa–Flynn–Wall, Kissinger–Akahira–Sunose and Friedman), by the Kissinger–Akahira– Sunose kinetic model. Using this method, Ea and A values are found to be very dependent on the conversion. Under lower conversion levels, higher Ea and A values have been calculated with respect to that found for medium and higher conversion levels.

By Aline Tatom

This paper presents numerical and experimen¬tal results dealing with the application of ferric ion oxidation of uranium in acidic media. Conclusions are derived from matching numerical results to experimental data taken on one-dimensional laboratory leaches using ore from a South Texas Coastal plain deposit. Since the numerical results can be made quite general, we are able to extract and quantify the effects of oxidant concentration, flow velocity, mass transfer, chemical kinetics, and competitive oxidant consumers (pyrite and molybdenite) on the experimental results. Our results suggest that the leaching of uranium is a mass transfer controlled while that of pyrite is kinetically controlled.

Jan 1, 1981

By Ananta L. Yennamani

Blast movement measurement (BMM) transmitters are a practical method to measure three-dimensional (3D) rock movement because of blasting. The BMM transmitters are activated, programmed and installed in specially designed drill holes prior to the blast and the BMM detector locates the transmitters after the blast. The BMM software then calculates and summarizes the 3D movement of each BMM transmitter ball. This information helps to redefine the ore and waste boundaries and enables improved ore and waste selection, resulting in a genuine step change in grade control. The BMM program was carried out at Newmont Mining Corp.?s Phoenix Mine, in northern Nevada near the town of Battle Mountain. The mine is in a historic mining district that contains gold, silver and copper. The geology of the pit consists of different formations made up of sandstone, siltstone, limestone, chert-pebble conglomerate, shale, skarn and quartzite, to name a few. Some of the rock is extremely hard and a powder factor of up to 0.5 kg/t (1 lb/st) is required to get adequate fragmentation to ensure sufficient throughput through the crusher and the mill. The result of using such a high powder factor translates into considerable blast movement and heave. This movement means that the ore/waste digging polygons estimated by the ore control engineer from sampling the initial blast holes will no longer be located in their original posi-tions. The purpose of this project was to test the measurement method and to see if locating the digging polygons in the broken muck pile and excavating to those polygons will improve grade control through the mill. Case studies (Zhang, 1994), (Taylor, 1995), (Gilbride, 1995), (Harris, 1997), (Taylor, 2003), Barrick Goldstrike (Gold-strike Mine, 2008), Ruby Hill Mine (Hilkewich, 2009), (Porcupine Mine, 2005) and (Aguirre, 2010) have shown that, by accounting for the blast movement, there is a potential to increase mineral recovery by as much as 25 percent for individual blasts for only a modest cost increase.

Jan 1, 2011

By B. Oraee

Tunnels as any other structures are affected by different loads and stresses. Generally, the loads on tunnels consist of both static and dynamic loads. These loads must both be considered in the tunnel design process. In this paper, the stability state of Jiroft water-transform tunnel is evaluated. Firstly, the in-situ stresses and then using Kirsch?s equations the induced stresses due to static loads in walls and crown of tunnel are calculated. Consequently, the strain caused by probable earthquake without considering the interaction between the concrete lining of tunnel and rock mass using seismic analysis is calculated based on free-field deformation. When the strain is determined, the simplified method of closed-form solution, Wang?s equations and Penzien?s equations are used to estimate the applied forces on the tunnel due to earthquake such as axial force and bending moment on a tunnel section taking into account the interaction of the tunnel concrete lining and rock mass. Results of this study show that the loads applied to the tunnel as a result of earthquake waves can be affect the stability of underground structures, especially long structures such as tunnels.

Jan 1, 2011

By J. Seiter, S. Cox, E. Kim

Mining has always been among the most hazardous of occupations, and with the increasing demand for coal and minerals, safety in mines assumes even greater importance. Worldwide, underground miners are being exposed to noise and respirable dust hazards associated with roof bolt drilling. These hazards are now being understood to cause irreparable damage to the health of miners. The objective of this research was to discover if a polycrystalline diamond compact (PDC) drill bit generates less respirable dust and hazardous noise than a competing tungsten carbide (WC) bit in dry vacuum drilling. In order to control the drill parameters the drilling tests were conducted in a laboratory setting. The results were obtained by determining the quantities of dust and noise generated using each drill bit and analyzing those levels, using monitoring devices and software to collect the data. This paper includes information on the experimental setup, equipment used, drilling parameters, and data collected. Our results indicate that PDC bits produce significantly less noise and dust than WC bits. Our findings can contribute to improving the working conditions of rock bolter operators by reducing noise and dust generation.

Jan 1, 2014

By Aleksandar D. Bugarski, Dylan A. Ritter

The results of laboratory characterization of tailpipe emissions for three “clean” engines that meet U.S. EPA Tier 4 final emissions standards were used to assess the viability and effectiveness of repowering existing engines and powering new mobile equipment with those engines as a control strategy for reducing exposure of underground miners to diesel aerosol and criteria gases. The evaluated engines were representative of those that achieve the emission standards through implementation of various in-cylinder emissions control strategies, use of crankcase filtration, and use of three types of exhaust aftertreatment systems: (1) diesel oxidation catalytic converter (DOC), (2) combination of DOC and the full-flow wall flow monolith diesel particulate filter (DPF), or (3) combination of DOC, diesel exhaust fluid (DEF) based selective catalytic reduction (SCR) system, and ammonia slip catalyst (ASC). The study showed that the highest reductions in concentrations of diesel aerosols in underground workings, in terms of both mass and number, could be achieved if the engines, preferably in all power classes, are fitted with viable DPF systems. The use of U.S. EPA Tier 4 final engines equipped with DOC and DOC/SCR/ASC systems could help operators to considerably reduce mass, but not number concentrations of aerosols. The emissions of two of the evaluated engines, one equipped with DOC and the other equipped with DOC/DPF systems, were characterized by substantial secondary NO2 emissions that would limit the viability of those engines for underground mining applications. It appears that the catalyst formulations used in the exhaust aftertreatment systems of the “clean” engines marketed to the underground mining industry need to be formulated to minimize the potential for generation of secondary NO2 emissions. The results indicate that the engines fitted with viable SCR/ASC systems present a low-NO2 alternative. All three “clean” engines were found to have low CO output. Therefore, due to nuances associated with the use of diesel-powered mobile equipment in underground mines, special attention needs to be paid to the selection and potentially optimization of “clean” engines for underground mining applications.

Feb 1, 2025

By A. M. Raichur, K. Keltner, M. Misra

The removal of oxyanions of arsenic present in mine process water and drinking water to a regulatory level (i.e. below 50 ppb) is a challenging problem. Conventional water treatment methods presently used for controlling arsenic have several drawbacks and limited success. A new adsorbent (LS™) developed at the University of Nevada, Reno, has strong specificity for both arsenate and arsenite species present in process waters. The adsorbent in very selective to oxyanions of arsenic and competition of other indifferent ions is minimum. Water samples from different sources were tested and arsenic was successfully removed to below 50 ppb. This paper describes both batch and packed column tests conducted in the laboratory as well as at the plant sites using LS™.

Jan 1, 1997

By Roger M. Buckeridge, Charles D. Reese, Silvio M. Martino, William T. Carey, Ansel H. Graham

FUNCTIONS OF RAIL HAULAGE SYSTEMS The principal application of rail haulage in under¬ground mining is in the movement of ore or coal pro¬duction from near the mining areas out to a processing plant. In some cases, such production haulage may end at a shaft pocket or slope belt conveyor transfer station, depending on the type of mine and the geo¬logical placement of the mineral being mined. Main-Line Haulage The basic reasons for choosing main-line rail haul¬age are high-tonnage production per shift and long haulage distances. The choice between rail and other systems, such as belt conveyors, is not easy and requires an integrated study of many factors: tonnage, distance, grade, product size, number of producing areas, ore reserve, safety, capital cost, operational and maintenance cost, and the mining system. Projecting a main-line rail haulage system for com¬parison with other systems requires a choice of many variables which are interrelated. The project must start with consideration of the mining system, tonnages per day, distances and grades, and loading and dumping conditions. Rail mine cars of different sizes and types are studied. High tonnage demands consideration of wider track gages. A suggested minimum for metal mines is 914.4 mm (36 in.); for coal mines, 1066.8 mm (42 in.). The choice of the train size should be governed by tonnage per shift, physical factors of loading and dumping, cycle time, and the number of trains that can be operated and safely controlled. After the size of the train is determined, the type, size, and specifi¬cations of the locomotive can be selected. The loco¬motive may be trolley, battery, or diesel; selection guides are discussed elsewhere in this chapter. The advantages of rail main-line haulage are high tonnage capacity, flexibility, reliability, safety, low operational and maintenance cost, and dual usage of the system (supply haulage, for example). The dis¬advantages are high capital investment, high installation cost, the requirement for more maintenance facilities, and restriction to certain ore reserves and mine pro¬jections. Supply Haulage Supply haulage is a basic requirement of any mine, but the type and volume of supplies vary with the type of mineral being mined, the mining methods, and the size of the mine. A mine developed for rail main¬line haulage gains supply haulage through the addition of a secondary track system to extend the main line closer to the producing areas. Additional haulage equipment, generally smaller, is also added. It is neces¬sary to design into the rail system more switch bypass points and train control systems. The track system standards demanded by rail main-line haulage con¬tribute to the reliability and efficiency of the supply haulage function, whereas a supply track system to supplement other haulage systems often suffers from poorer track and installation standards. When belt conveyors are chosen for production haulage, a rail supply haulage system is often installed rather than using rubber-tired vehicles for supply haul¬age. The conditions of the seam or ore body create these items for consideration: haulage grade of more than 6% favors rubber-tired vehicles; longer haulage distances favor rail; difficulty in maintaining a smooth roadway favors rail; and movement beyond the end of a rail system generally requires rubber-tired vehicles, making a single system rather than a dual system attractive. Although operation of a supply haulage system may be concentrated on a single shift of a multiple-shift mining operation, proper planning and supervision are required if the haulage is to be efficient. Often the newer personnel at a mine are assigned to supply haul¬age which may add to the difficulty of obtaining maxi¬mum efficiency. Supply haulage by rail offers the advantages of high reliability, lower maintenance, and high efficiency over long distances. The disadvantages are less flexibility, high installation costs, and rubber-tired vehicles for use beyond the inby end of track often required. Personnel Movement The efficient and comfortable movement of the miner to and from his work area has a significant effect on his daily output. Minimizing man-trip time also becomes more and more important as hourly wages increase. Personnel are generally moved over a rail system by one of three methods: a specialized personnel carrier to which a certain number of men who work in a certain area are assigned; a combination vehicle, used to carry personnel but also capable of being used as a light supply/utility locomotive during a working shift; and man-trip cars towed by a supply locomotive. The first and second methods are used in coal mines where long distances make speed and comfort important. The third method is more common in metal mines. Equipment Movement As mining equipment technology has advanced, many mining machines and their subcomponents have grown in size. This trend requires careful planning for adding specialized carriers to handle the movement of larger equipment. Continuous miners, longwall equipment, raise borers, and ventilation equipment are examples of machines which may be difficult to move and which require special handling. The selection of the weight, speed, and operating characteristics of supply locomotives used to move equipment is important. Larger mines may often justify a special group of loco¬motives for this application.

Jan 1, 1982

By W. R. Penney, J. M. Richardson, J. Y. Oldshue

Introduction The mining industry has for years underrated the value of mixing in mineral processing unit operations. In present-day operations where leaching is playing an ever increasing role in the total profit picture, the need for good mixing is becoming more obvious. The engineer in the research laboratory and in the operations is by necessity becoming more familiar with the concepts of mixing. This section is designed to provide the engineer with mixing data and correlations sufficient to assist in the general planning of simple mixing systems.

Jan 1, 1985

Well designed and maintained haul roads are the key to minimizing truck haulage on-road hazards and costs, as well as increasing productivity. However, practically designing and managing a haul road for optimal performance is often difficult to achieve. Poorly designed and built roads exhibit high rolling resistance - a 1% increase in road rolling resistance can typically reduce speed on ramp by as much as 10% - and on the flat by up to 26%. In the current economic climate, investment and operating decisions come under scrutiny. In the long run, this scrutiny returns improved efficiencies and leaner, healthier operations. The focus of this evolving evaluation process should and will certainly fall on haulage operations ? simply by virtue of their contribution to overall cost of operations ? often in excess of 50% of total costs for deep open-pit mines. Whilst the end result - improved efficiency and reduced cost per ton hauled ? is not in itself problematic, it is the route, or process followed to achieve these savings that needs to be carefully managed. We can be guided on this journey by our understanding of how a road design is developed, and, critically, the interplay between a good design and safe, cost efficient haulage. This paper briefly summarizes the evolution of mine haul road design, from the seminal USBM work of Kaufman and Ault in 1977, through to current geometric, structural, functional and maintenance management design components. These augmented design and management guidelines have been developed over the past decade, both in response to the requirements of mine operators for more safe and efficient haulage systems, and the truck manufacturers? requirements for a more predictable and controlled operating environment. These developments have been paralleled by the need to minimize haulage hazards, both from a health and safety perspective. Whilst improved mine haul road design does indeed reduce haulage accidents, recognition also needs to be given to human factors which are a significant contributor to haulage accidents. The human factor is the most problematic to address in a road design. It is often easier break the link between the interactive effects which may lead to accidents than trying to predict and reduce human error. These human factor interactive effects include the geometric, structural and functional design components and to prevent an accident or reduce the severity of its consequences, a road should be more accommodating to human error. The more that is known about human error, the better a road can be designed to accommodate those actions or non-standard practices that would, on a poorly designed road, invariably escalate an error into an accident.

Jan 1, 2010

By Charles T. Ford

In 1971, Bituminous Coal Research, Inc~ established a program to provide the coal industry with the necessary information and technical capability to investigate and evaluate potential problems concerning trace elements in coal and coal-related materials. The initial efforts at BCR in developing or adapting analytical procedures for the precise determination of trace elements in the parts per million to parts per billion range were detailed in a report titled "The Development of Analytical Methods for Determining Trace Elements in Coal and Coal-related Products." A subsequent reports contained descriptions of reliable analytical methods refined by BCR for determining mercury in coal and coal ash and also in coal mine water. his paper reports initial progress in applying recently-acquired trace-element analytical capabilities to solving potential coal industry problems. In this case, the effect of a coal-cleaning process on the distribution and removal of potentially harmful trace elements in coal was evaluated. Coal cleaning offers the possibility of controlling potentially harmful emissions resulting from combustion of large tonnages of coal by removing the pollutants prior to combustion.

Jan 1, 1977

By C. F. de Mendonca, T. Kater, R. P. de Souza

The authors are to be commended for finding a material for pellets binding that we were unable to uncover during the investigations that led to US Patent No. 3,748,116, “Method for producing metallic iron powder from iron ore concentrate, ” July 24, 1973, by G.G. Reed, Jr., J.M. Karpinski, and S.V. Fox. This patent concerns a method of processing “super’ ‘-concentrates prepared from magnetite or “blue dust” into molding-grade metallic iron powder for use as a bulk commodity, in contrast to current methods which produce small batches that are custom-blended with additives and/or alloye to customer specifications. The one thing we had not found at that time was an organic binder (mineral-matter-free ) that would allow induration to produce hardened pellets that would survive SL/RN Direct Reduction. Peridur appears to provide this missing link needed for large scale (200 t/a, or 220,460 stpy) single line plant capacity consistent with a low market price to ensure greatly broadened use of metallic iron powder. I hope that industry will adopt this combination so that metallic iron powder usage can fulfill its potential

Jan 9, 1985

By Pratt Rogers, Aaron Young

This paper considers the mining industry’s need for digital transformation (DT) and presents a three-part review of the foundational components of the DT process: ubiquitous data, connectivity and decision-making. It also provides a discussion on the future of DT in mining as well as a research direction, which identifies the need of academia to provide support for mining companies in the form of both research and the education of digitally literate, dynamically capable mining engineers into the coming decades.

By C. L. Lin

The characterization of rare-earth resources in 3D is now possible using high-resolution X-ray microtomography (HRXMT) to describe ore texture and mineral phase composition. In addition, detailed texture analysis, including grain exposure and mineral association, can be described. Preliminary examination of a sample of Mountain Pass ore is reported to describe the spatial distribution of the mineral phases (calcite, barite and bastnaesite), particularly the grain size distribution of bastnaesite. The examination includes analysis of selected particle size classes to determine the appropriate size for liberation of the rare-earth mineral bastnaesite. Good liberation is expected to be achieved if the material is ground to a top size of -150 µm.