Search Documents

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By K. L. Ludeke

For many reasons it appears that deep-rooted, perennial shrubs offer potential for improved stabilization and provide maintenance-free vegetative cover to harsh sites where perennial grasses have not been successful. The very fact that a drought-adapted shrub has a massive root system that can use moisture from a greater volume of mineral waste soil materials suggests that long-range arid environment resource development may be greatly enhanced by utilization of desirable forage shrubs. An effort is underway to assemble information and plant materials of promising species from many arid regions of the world. Surprisingly, many of the better plants for arid sites are quite high in protein content, and with proper management, breeding, and selection may prove to be very desirable livestock feed. Advancements in arid-land solid waste stabilization hold favorable promise for many industries that mine and mill in arid regions for effective reclamation of disturbed areas. Particularly exciting is the possibility of establishment of high density maintenance-free vegetative cover of climax vegetation that reclaims the disturbed area back to its original land use. Because of high shrub productivity, stabilization potential, nutritional quality, and reclamation success, greater use should be made of shrubs in disturbed land reclamation associated with mining and milling operations in harsh arid environments.

Jan 1, 1984

By George E. Peacock

Campbell Red Lake Mine is situated at Balmertown, in the Red Lake District of Northwestern Ontario, Canada. This area is some 120 miles north of the Trans Canada Highway and is some 160 miles Northeast of Winnipeg, Manitoba. The majority of our 300 employees live in Balmertown, which is a community of some 1,200 people, situated adjacent to the mine proper. The mine is serviced by a single shaft 4,300 feet deep. There are 27 levels at 150 ft. intervals. Stoping is being carried out down to the 20th level with only preliminary development having been done on the bottom 6 levels. The majority of our mill feed of 825 tons per calendar day comes from above the 10th level. Gold occurs as specks and streaks in bluish-grey to white quartz carbonate veins. It is extremely fine grained and most is invisible to the unaided eye. In addition to Gold the veins carry varying amounts of sulphides such as, Arsenopyrite, Stibnite, Pyrite, Pyrrhotite and Sphalerite. A minor amount of silver occurs as an impurity in the gold. Arsenopyrite is a marker for the gold ore at Campbell. The average grade of the mill feed is 0.7 oz. of gold per ton. The ore is dumped into an underground ore pass that feeds to a jaw crusher on the 20th level that reduces the rock to a maximum size of 4". This material is hoisted by skips to an ore bin in the head frame.

Jan 1, 1975

By Gennaro G. Marino

This paper summarizes and evaluates data on mine subsidence ground movements and associated damage for houses in Illinois. Based on the data collected, the response of homes to subsidence ground movements is expressed in terms of repair costs. A damage criteria is then proposed that relates the ground movements and damage levels. The data were collected as part of a comprehen¬sive study performed for the Illinois Abandoned ?Lined Lands Reclamation Council, A -M-RC, by the Civil Engineering Department at the University of Illinois, and probably will be published in late 1934 by the council. The study concentrated its efforts on surface ground movements and the effects to houses over abandoned room and pillar mines. The resultant surface subsidences are commonly dish or bowl shaped and are termed sags. Method of Analysis The steps in analysis used to arrive at the proposed damage criteria are: 1. Canvas and rap subsidence damage in houses, 2. Assess the associated ground movements, 3. Estimate the damage repair cost, 4. Develop a damage/repair level classifica¬tion, 5. Correlate the associated ground movement, damage/repair level and home construction type, 6. Propose a damage criteria.

Jan 1, 1984

By Lawrence Adler

The design of an underground opening involves the coincidence of two highly complex and poorly specified components. First, the structural or mechanical characteristics of a geologic rock mass are not only extremely variable but are also very difficult to evaluate. Second, the general lay¬out of mine workings contains a large degree of indeterminancy as to the structure itself as a result of the indefiniteness of the mining process, and also because of the inherent redundancies associated with bulky and weighty structures. Even for the relatively simple problem of tunneling this complexity is well recognized to be "without question that to which the study of geo¬logy (for the Engineer) can most fitly and usefully be applied".1 It can, therefore, be appreciated that the comprehensive opening design problem involves a complicated assemblage of component structures made up of a sketchily defined, or sometimes even an undefined material and acted upon by largely unknown tectonic forces.

Jan 1, 1968

By B. W. Lawrence

Shaft alignment requirements are consistently met using conventional shaft sinking methods. Little attention has been given to achieving similar alignment accuracies using rotary drilled shaft methods. Alignment of these shafts is difficult to control and guarantee. Bare shafts and shafts that use drum hoisting systems can accept some deviation. However, combining drilled shafts with Koepe hoist installations presents new accuracy requirements for drilled shafts. This paper describes the importance of verticality with practical examples, and discusses various methods of measuring verticality and their respective limitations.

Jan 1, 1989

By Andre Vien, Frank Laroche, David Di Sandro

Back in 1994, Claude Bazin presented a novel method for linking size data from milling models to the feed input of flotation models. It was achieved with the simple addition of a metal/mineral distribution—size distribution relationship. This allows grade and recovery predictions from a varying mine plan via product size distribution predictions. This paper presents a case study where this elegant method has been used to build a very powerful forecaster at a process plant, built from historic operating data. The methodology has been used by this operation to forecast production on a quarterly, annual, and life-of-mine basis since the late 1990s. It has been upgraded several times to incorporate new drivers as the complexity of feedstocks has increased over the years.

By A. Davis

Pit lake chemistry depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock versus oxidizable sulfide content, and the alkalinity of recharging ground water. In this paper, we assess the geochemistry of 11 existing pit lakes, ranging from the acidic Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington Pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits with the long-term pit lake chemistry lying on a geochemical continuum between end members consisting of influent calcium bicarbonate ground water, and naturally occurring sulfate-rich evaporite playa lakes.

Jan 1, 1996

By J. H. Schuenemeyer

Uncertainty estimates on coal resources were computed as part of the U.S. Geological Survey’s National Coal Resource Assessment study of more than 60 coal beds and zones in the Appalachian Basin, the Colorado Plateau, the Gulf Coast, the Illinois Basin, and the Northern Rocky Mountains and Great Plains. The estimates were made to provide zone specific measures of uncertainty on the historical categories of geological assurance, namely measured, indicated, inferred and hypothetical. Previous estimates were based solely upon distance from a drill hole. These new estimates incorporate site-specific variability and spatial correlation and indicate that there is considerable difference in variability within and between regions. Uncertainty estimates for the measured category are discussed in this paper.

Jan 1, 2001

By A. M. Gaudin

A new method of measuring the viscosity of unstable suspensions has been developed, using a Heinz viscometer. The technique was applied to kaolin-water suspensions. Spreads in viscosity with lime additive were measured.

Jan 1, 1962

By Andre Vien, Frank Laroche, David Di Sandro

Back in 1994, Claude Bazin presented a novel method for linking size data from milling models to the feed input of flotation models. It was achieved with the simple addition of a metal/mineral distribution—size distribution relationship. This allows grade and recovery predictions from a varying mine plan via product size distribution predictions. This paper presents a case study where this elegant method has been used to build a very powerful forecaster at a process plant, built from historic operating data. The methodology has been used by this operation to forecast production on a quarterly, annual, and life-of-mine basis since the late 1990s. It has been upgraded several times to incorporate new drivers as the complexity of feedstocks has increased over the years.

By C. E. Semler

A multiyear program involving online, in-vessel exposures at Barrick Goldstrike Mines Inc. (BGMI) has provided information and experience about the materials and designs for brickwork linings in pressure oxidation autoclaves. A variety of brick and mortar products was evaluated. Properties before and after exposure were used to document the performance. Some benefits include the development of a new silicate mortar, a better understanding of brick requirements and increased autoclave operating time between maintenance shutdowns. BGMI operates six pressure oxidation autoclaves at its Eureka County, NV gold operation. These autoclave process 15.8 k/ld (17,500 stpd) of gold ore. Figure 1 is a flowsheet of the six autoclave circuits. The gold ore is refractory, in which the gold particles are mineralogically encapsulated on a micro- and submicroscopic level. The autoclaves are 4.4- m- (14-ft-) diam and 26 m (85 ft) long (tip-to-tip). Inside of each is a full brickwork (brick plus mortar) lining that divides the vessel into five compartments. Each compartment has a motor-driven agitator that keeps the slurry suspended and disperses the oxygen to enhance reaction. During autoclave operation, the conditions are steady state at 210° to 232° C (410° to 450° F) and 61 to 62 kPa (420-430 psi). As shown in Fig. 1, there are other accessory vessels (splash and flash towers) in the autoclave circuits that are also brickwork-lined. The linings used to date, other than small test sections, have all been acid-resistant fireclay bricks, bonded with alkali silicate mortar, PbO- based mortar and/or vinyl ester mortar, but mainly alkali silicate mortar.

Jan 1, 1997

By Richard C. Corson

Modern microprocessor systems make it possible to use several variables to anticipate changes in the process and to react with responses before upsets can be magnified by the process or by control action. Through tighter control, "insurance" can be eliminated from process set points without affecting product quality. In actual operation with a traveling grate furnace this control philosophy has produced savings of up to 20% in fuel consumption and 8% in fan power usage while producing a more consistent quality product.

Jan 1, 1982

By T. R. Ley

"INTRODUCTION Brutally honest mining executives will tell you that “safety is job #1 but.. dollars are also extremely important”. When economic times are tough, as they are now in mining, it can feel like you need to choose between safety and cost control. Leading edge companies know that it is excellence at both that provides the best performance. FLUID POWER SYSTEMS Fluid power systems are ubiquitous in mining – longwall systems, continuous miners, drills, haul trucks and excavators, etc. And fluid power systems are getting more powerful and using higher pressures to move greater volumes and achieve higher productivity. Average operating pressures in mobile equipment has been rising to 450 bar (6,500 psi) over the last decade. With increased system pressure comes ever increasing levels of stored energy. Stored energy that, if released in an uncontrolled fashion, can do tremendous harm to people and things.Fluid power systems are composed of pipe, flexible hoses, pumps, valves and actuators. They are filled with fluid (mineral oil or fire-resistant) to transmit power to where it’s needed for performing work. With time and use fittings can loosen, component performance diminishes and hoses wear and tear. In hostile environments, like coal mining, hydraulic hoses can fail in as little as 2 years according to DGUV (umbrella association of German Accident Insurers), maybe sooner in some particularly challenging environments. FLUID POWER SYSTEM SAFETY While appearing simple and benign on the surface, fluid power systems, particularly such systems on mobile equipment, have many potential hazards. Hazards that most workers aren’t aware of – particularly young, new hires. And those hazards that can quickly turn deadly. During the past couple of years, including at last year’s SME Conference, I talked to a wide variety of mining people about high pressure fluid injection injuries. Some people, often with little or no field experience, never heard of it. But, people with mine operations / maintenance experience were almost always aware of such injuries.Some had even seen it happen right in front of them. But most claimed it didn’t happen all that often. It just wasn’t seen as a problem!"

Jan 1, 2016

By Alan D. Randolph

A size-continuous breakage kinetics model is postulated and supported with industrial grinding mill data. It is shown that the kinetics parameters include the effects of possible classification at the mill discharge. The estimated parameters were then used in the kinetics model to simulate the behavior of a grinding mill in open and closed circuit operation. While material transport and kinetics are equally important in open loop operation, heavy recycle in a closed circuit make a detailed material transport model for grinding unnecessary. In effect, the mill can be considered as backmixed. This suggests that more emphasis should be placed on modeling the classifier than the development of detailed material transport models for the grinding mill.

Jan 1, 1975

By DIONISSIOS T. HRISTOPULOS, JUAN DIAZ, Kray Luxbacher, Steven Schafrik, Zach Agioutantis

Explosions in underground mining due to methane gas have been the leading cause of incidents and fatalities in the mining industry. The main objective of this research is to develop a forecasting methodology for methane gas emissions based on time series analysis. Methane time series data were retrieved from atmospheric monitoring systems (AMS) of three underground coal mines in the United States. The AMS data were preprocessed and statistically evaluated to explore the potential autocorrelation of methane gas. It was concluded that the autoregressive integrated moving average (ARIMA) time series model used in the one-step-ahead forecasting mode provides accurate estimates that match the increase or decrease of the methane gas emission data.

Feb 1, 2023

By H. Soto

As a follow-up to a laboratory study, a pilot scale column for the flotation of coarse particles was designed and then tested in two different applications. In the first test, the concentration of a coarse phosphate ore (normally beneficiated by skin flotation in spirals) was carried out in a flotation plant in Florida. In the second pilot test, the column was used as a scavenger cell in the coarse flotation section of a potash beneficiation plant in Saskatchewan, Canada. Particle size of the phosphate feed was of the order of 0.6-1.0 mm and the potash feed 1-3 mm. The column was 1 feet diameter and was fed at rates between 0.5 to 1.4 tph. The effect of operating variables such as air and water flow rates, bubble size, frother concentration, residence time, sparger, etc were evaluated. The most important factors in column performance were found to be bubble size, air flow rate and the thickness of the froth bed. Best results were obtained in the absence of a froth bed, with low air flow rates and with small bubbles. The paper presents comparative performance and discusses details of the column design. Phosphate recoveries in the column were better than 90% whereas the conventional skin flotation circuit normally yields about 60% recovery for a comparable concentrate grade. Potash recovery from the tailings of the conventional flotation circuit was as high as 42% recovery. Particle size distribution of the potash concentrate was coarse enough to meet requirements for potash fertilizer.

Jan 1, 1993

By J. Alvarez, S. H. Castro

The feasibility of chalcopyrite-pyrite separation in the flotation of a chalcopyritic copper ore, at reduced surface tensions regulated by methanol, was investigated. It was found that with methanol dosages from 0.5% to 1.5% v/ v, the chalcopyrite might be effectively separated from the pyrite, without use of other flotation reagents and pH regulators. However, under this simple condition, the chalcopyrite recovery was only around 50%, recommending the use of other reagents to reinforce the collector action. Low dosages of different collectors were tested, including SF-323 (Shell Float), S-6588 and S-7251 (Cytec), and S-701 (Molycop). Very promising results were obtained with low dosages of the collector S-701 and 1% v/v of methanol in the pulp, which evaluated against a reference test, gave similar copper recovery, higher Mo recovery and higher depression of pyrite. Consequently, this is an alternative process which does not require the use of lime to depress pyrite.

Jan 1, 1995

By Xuebin Liu, Yi Shang, Can Zhou, Hongqiu Zhu, Junbo Du

In the neutral leaching process of zinc hydrometallurgy, the pH value directly affects the leaching rate of zinc calcine. However, due to the complex mechanism of the leaching process and frequent fluctuation of working conditions, it is difficult to control the pH value by manual control. Therefore, this study proposes a fuzzy control method based on rule extraction under multiple working conditions, and analyzes the pH control performance. Firstly, the different operating states are classified according to process mechanisms and the Pearson method. Secondly, under the framework of the active learning algorithm, the approximate linear dependence (ALD) method is introduced to iteratively select samples with rule information in the original sample set for manual annotation. Then, the support vector machine (SVM) method is used to extract fuzzy control rules in different working conditions. Finally, a fuzzy rule set is established according to the samples mapped by the support vector. The simulation results based on industrial data show that the proposed method has better control performance than conventional fuzzy control and proportional–integral–derivative (PID) control.

Apr 1, 2024

By J. R. Kunkel, V. Lishnevsky

At mine sites, the operational and required storage volumes of solution and water storage ponds and reservoirs are usually calculated based upon a water-balance approach. Many climatological variables including precipitation, air temperature, solar radiation, pan evaporation and relative humidity along with operating parameters, are used in the water-balance model. The water-balance model often seeks to find a “critical period” of wet or dry climatological sequences which result in a “maximum” pond storage volume or water demand. The problem with this approach is that the designer usually does not know when the project will come on line in relation to the historical record. To avoid this pitfall, we use a more robust approach. In the more robust method, the water-balance calculations begin in each year of the historic climatological record. This method results in the same number of water-balance runs (or realizations) as the number of years of climatological record. Results of this type of analysis guarantee that the critical period or maximum required pond volume will be found if it is assumed that the historical climatological record repeats itself or if a synthetic time series is used. In addition, this method permits calculation of the likelihood (probability) that a given pond volume will be equaled or exceeded in any given month of the operational life of the facility. In this paper, the results of the sizing of a heap leach pad solution pond are presented along with the probabilities of a given solution pond size being equaled or exceeded based on the robust water-balance approach.

Jan 1, 2002