Search Documents

By J. O?Hanlon

The 4500 m3 blast furnace at the Redcar Works of ESC operates or, a burden of sinter and pellets, both materials being produced within the works. The early history of the furnace was given to the AIME Ironmaking Conference in 1981(1) when the burden was 65% superfluxed minter and 33% acid pellets. While ironmaking performance was adequate, it was felt that there were advantages to be gained by the use of fluxed pellets. For example, Kobe Steel had reported (2) that the rise of 30-50% dolomite fluxed pellets had enabled them to achieve better furnace permeability, higher gas utilisation, and enhanced ore/coke ratios. It appeared probable to BSC that the use of magnesia-bearing fluxed pellets would give a burden which had compatibility of softening and melting properties, i.e., fluxed sinter and dolomite pellets would result in a thinner cohesive zone because of closer matching of softening and melting temperatures, with consequential benefits on furnace stability and efficiency.

Jan 1, 1983

By MUSTAFA ERKAYAOGLU, ENVER YILMAZ

Coal mining is likely to sustain its critical role as energy requirements are increasing. While surface mining exploits coal seams near the surface, underground mining techniques are crucial for extracting deep coal reserves. Longwall mining is one of the most common methods used in underground coal mining operations. This paper introduces a data-based framework — including data collection, data analysis and the interpretation of operational data — for understanding the system efficiency of a longwall shearer. Operational performance is evaluated by the time between arrivals (TBA) and duration of the shearer stoppages, shearer drums’ reversal time, cutting speed and flit speed on daily production in a longwall top coal caving (LTCC) mine. A discrete event simulation model is developed to represent the bidirectional cutting sequence of a longwall shearer.

By Andrew L. Mular

Methodology to model, simulate and optimize full scale mineral pro- cessing circuits in production environments is reviewed and evaluated. Strategies for data acquisition and adjustment are considered along with techniques to fit models to adjusted data. Examples are considered for clarity.

Jan 1, 1989

By Neil D. Policow

Dewatering of the fine clean coal fraction, - 28 mesh (595 microns) represents one of the most difficult and costly separations in typical plant circuits. Since 1969, the Screen Bowl Centrifuge has offered an economical alternative to filtration/thermal dryer combinations. The performance of Screen Bowl Centrifuges has been continuously modified and improved to dewater not only coarser coals, but also today's variety of ultrafine material. Actual test comparisons with alternative methods show the Screen Bowl Centrifuge to be most cost effective and efficient when all factors are considered.

Jan 1, 1982

By D. H. Stonehouse

There is no such thing as an industrial minerals industry. There are, however, many industries operating in the general field of industrial minerals. And although we use the phrase "industrial minerals industry" out of sheer convenience, the only common denominator among, say, the potash mining and processing industry, the sulphur-sulphuric acid industry and the granite industry is, in fact, that they each are exploiting an industrial mineral resource. May I quote the person whom I consider to be the reigning Mr. Industrial Minerals, Robert L. Bates, who in the 4th edition, 1975, of Industrial Minerals and Rocks states: "An industry is considered to belong to the industrial minerals field if its operations consist of extraction and processing, but not manufacturing. Thus the mining and beneficiation of feldspar is a mineral industry, but the manufacture of ceramic products is not. In the cement and lime industries, processing merges into manufacture, and the line is less distinct. It disappears altogether in a plant that extracts salt as artificial brines, and makes sodium and chlorine chemicals, all under the same roof."

Jan 1, 1981

By Robert A. Bauer

Two basic types of subsidence occur in Illinois: pit and sag / trough. Pits develop over mines less than 165 feet deep and where relatively incompetent strata are found over the mines. Sag subsidence is found over mines as shallow as 75 feet and more generally over mines of greater depths. The percentage of subsidence and angles of draw associated with sag subsidence appear to be controlled by the rock properties at each specific site. The percentage of subsidence and angles of draw are smaller where the sites are not affected by geologic structures. An investigation to determine if a time factor based on the time interval from the date of mining to the subsidence events has shown that simple correlations with time, percent extraction, average pillar stresses, and pillar dimensions is not evident in Illinois.

Jan 1, 1982

By DING TANG, JINGHE CHEN, Shuiping Zhong, CHEN KUANG

The Zijinshan gold-copper mine, located in Shanghang County, China, is a porphyry-type, low-grade ore deposit with a geological profile of upper gold and lower copper. Despite its low-grade nature, it has become one of the largest in production scale and most profitable nonferrous metal mines in China, which can be attributed to the successful application of hydrometallurgy as well as proper engineering design. A large-scale, open-air cyanide heap leach has been successfully implemented to recover gold under the humid and rainy weather conditions of southern China. Furthermore, according to the gold ore characteristics, a combination of gravity separation, carbon-in-leach and heap leaching processes was developed to improve gold recovery. In terms of copper extraction, copper ore of a grade higher than 0.25 percent is fed to the flotation plants to produce copper concentrate (gold is also enriched here), while copper ore of a grade lower than 0.25 percent undergoes heap bioleaching followed by solvent extraction and electrowinning to produce cathode copper. Additionally, a unique bioleaching system has been established at the Zijinshan Mine: low operating pH (0.8~1.0), high concentration of total soluble iron (~50 g/L), high temperatures (45~60 °C) and low activity of microorganism (~104/mL) in the pregnant leach solution (PLS). This review paper summarizes the practical experience acquired in developing the Zijinshan gold-copper mine and could be of use in other gold and/or copper plants.

By Michael von Seebach

High-pressure grinding rolls subject the feed material to pressures of 200 N/mm? During this process considerable size reduction and the Formation of flakes occur. This paper describes the basic consideration For design and operating of this type of mill. It is also shown that the particle size distribution resulting from this process is typical for grinding processes but untypical for crushing processes. High pressure grinding rolls are designed in size of up to 2.8 m roll diameter allowing feed material top sizes of 250 mm. The rigid frame, bearing and drive - train design allows a broad application of the high-pressure grinding rolls operating the machine in open or semi-closed and closed circuit for dry and moist feed materials. Operating results show that capacity increases of up to 100 % can be accomplished with this technology. The high-pressure grinding roll also, allows for lower operating and maintenance costs due to energy savings of up to 20 L and reduction of wear to less than 1 76 for dry and less than 0.1 5 for wet grinding. Other advantages of the high-pressure grinding rolls are smaller equipment sizes than a ball or SAG-mill for a given capacity resulting in lower building sizes with reduced capital in- vestment costs.

Jan 1, 1987

By Timothy P. Smirnoff, Anthony Stirbys, Amanda Elioff

The construction of the continuing expansion of the Los Angeles Metro System has required the construction of eight new station structures. One contractor proposed, as a construction alternative for the support of excavation of the Hollywood/Vine Station, the use of soil-mix walls instead of the conventional soldier piles and wood lagging. Soldier piles and shotcrete or wood lagging support systems had been generally used on the other sub-way station excavations constructed to date throughout the system. Immediately east of that station and in almost exactly the same geology, the Hollywood/Western Station was being excavated at the same time using a conventional support system. This paper com-pares the performance of these two support systems in the alluvial soils of the Los Angeles Basin.

Jan 1, 1997

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study is to compare amino acids and organic acids in the extraction of gold from silicate ore. Amino acids were found to have higher efficiency of gold extraction than organic acids at the same acid concentration, which is likely due to amino acids having both carboxylic and amine groups in their structure, while organic acids only have carboxylic groups. Five amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and seven organic acids (citric, malic, tataric, fumaric, oxalic, succinic and ascorbic acids) were selected to investigate gold extraction efficiency. Aspartic acid was found to have greater capacity to extract gold than succinic acid. The optimal gold to aspartic acid molar ratio was 1:6, and low concentrations of aspartic acid extracted 35 to 42 percent of gold from silicate ore within 15 days. Further studies are needed to increase gold leaching and reduce incubation time. The results imply that aspartic acid can be used as an alternative reagent to traditional methods for extracting gold from ore. This method is nontoxic to humans, is environmentally friendly and can have real applications.

By Y. M. Jiang

Many underground instabilities, such as excessive shield loading and roof falls, occur at longwall faces causing safety problems and production losses. Such instability problems are directly related to roof conditions which can be categorized using geological information. . However, most geologic information describing anomalies and variations of immediate and main roofs are not available before mining resulting in unexpected problems in a longwall face. It is apparent that the evaluation of these geologic anomalies provides a great benefit for longwall stability. The purpose of this study is to evaluate roof categories associated with geological anomalies employing fuzzy set theory. The evaluation is based on real-time monitoring information, such as shield leg pressure, developing load on shields, intervals of periodic weighting, and the ratio of developing loads during periodic to normal times. This paper introduces the application of fuzzy set theory for characterizing roof conditions and evaluating of roof similarities.

Jan 1, 1995

By John F. Burst

For several generations now, the high alumina clayey sediments of Southeastern Alabama and Southwestern Georgia have supplied those regions with steady, mineral-based income although the impact of that income has been relatively minor until recently. Since World War II, mining activity has increased algebraically with over half of the total ore value in the Alabama area having been recovered since that time. The Georgia area production increases are even more dramatic. The trends are continuing and the next decade should see ore winning figures which will dwarf all previous production. It's time for the mining engineers to take note of this development as the mining methods, similar to the production, have developed rapidly and now offer challenges for the most competent professional. The development of mining techniques has followed a classic pattern. Beginning almost a hundred years or so ago, with the loading of weather-resistant surface boulders into mule-drawn wagons, mining methods have progressed to discovery of limited surface exposures in outcrop and eventually to stripping and development of non-obvious, subsurface deposits. Little by little, the overburden thickness of new pits has increased until, at present, pits with 100' -125' of overburden are being actively worked. Ground water problems in the Eufaula District are particularly challenging. At A. P. Green's J. W. Baker Pit, #l, in Barbour Co., Alabama, it is necessary to continually pump groundwater at the rate of about 400 gallons per minute from wells on the periphery of this large pit in order to keep the water table low enough to allow mining of the ore body.

Jan 1, 1972

By A. M. Marabini

Flotation of rutile with N-benzoyl-N-phenyl-hydroxylamine (N-BPHA) has been investigated. Initially, floatability tests were performed in a Hallimond tube. The results indicated that rutile was floatable in the pH range from 2 to 4 at N-BPHA concentration between 2x10-3 M and 2x10-2 M. Selectivity against hematite was recognized when operating at pH values below 2. Following the hypothesis of the formation of a surface chelate between N-BPHA and titanium ion, this compound was precipitated from a solution of Ti(SO4) to which N-BPHA was added. I.R. spectrometry oft the rutile before and after treatment with N-BPHA solution confirmed the presence on the rutile surface of the same compound. The absorption isotherm and kinetics were determined by analyzing N-BPHA in solution with an U.V. technique. A hypothesis for the mechanism of adsorption of N-BPHA on rutile is suggested.

Jan 1, 1982

By P. W. Erickson

Development of the Twin Buttes mine entailed the largest known preproduction stripping job in the history of mining. It linked earthmovers and conveyor belts in a new approach to development of a pit that may reach, or even exceed, dimensions of 1 x 1-1/2 miles at the surface and go as deep as 1800 feet. The orebody to be stripped was covered by an average of 460 feet of alluvial gravels, which presented an initial stripping job of great magnitude. The initial pit layout and the original time schedule established early in 1965 called for the excavation and disposal of about 250,000,000 tons of alluvial overburden before the end of 1969. Allowing about a year for equipment delivery, this schedule left four years to do the job averaging about 62-1/2 million tons per year. In 1964 when The Anaconda Company undertook the development of Twin Buttes, it was recognized that special planning was necessary for the disposal of waste material and tailings. Environ- mental control was a prime consideration and is particularly sensitive in the Twin Buttes area due to the proximity to residential developments. Disposal of the 250,000,000 tons of alluvium, as well as future rock and tailing waste material, presented a problem which Anaconda engineers resolved by designing a plan to spread out much of the alluvium over an extended area, including a massive 11- 1/2 mile dike system which will impound mill tailing in three basins. The tailing will be impounded behind these-dikes to avoid wind exposure and blowing. The dikes also serve as a

Jan 1, 1974

By C. Cardoso, G. Bermudez, A. Jalili

Bigger flotation cells can result in larger froth surface areas and longer froth transport distances, this has been credited to impact froth recovery. Thanks to recent advancements, the newer flotation machines can be designed with different launder and crowder arrangements to enhance froth management. Nevertheless, lower head grades, complex ores and even larger mechanical flotation cells can lead to insufficient froth collection, even if the cell is equipped with the most recent flotation advancements like the center launder design. Aforementioned issue can become critical at the end of the flotation row. Increased crowding has been proven to be a solution to overcome inadequate froth recovery. However, scaling-up crowders for larger flotation cells can rise challenges, particularly in terms of structural limits and design for service. This paper presents the development journey for the Spider Crowder Upgrade, an advancement to improve froth collection in large flotation cells that are already equipped with center launders.

Feb 1, 2024

By Mark E. Gershon

Extensive efforts are under way to- ward applying computer techniques to mine production scheduling problems. These efforts are concentrated in four areas: optimization, computerization of traditional methods, heuristics and simulations. These areas complement each other rather than compete. Characteristics of each are discussed toward enabling the engineer to evaluate specific systems that may be encountered. Alternative approaches within each classification are described as well as the motivation for each.

Jan 1, 1985

By Raja V. Ramani

In many instances, the actual production from a longwall face does not equal the planned capacity. General problem areas which have been identified include face length and panel depth, face area and gate entry roof support, face conveyor and shearer wear, outby haulage system failures, number of entries in longwall gate development and longwall move time. The performance of a longwall face is totally dependent on the interaction of these and many other factors. To explore fully these interactions, a systems analysis of longwalls has been performed. In this paper, the systems approach, the factors considered in the analysis, and the results of the analysis are presented.

Jan 1, 1983

By Nora M. Hutt, Kevin A. Morin

There is currently some pessimism over mixing of net-acid-neutralizing (NAN) and net-acid-generating (NAG) rock to obtain indefinite near-neutral seepage from mined-rock piles. This is due in large part to the lack of well- documented, successful cases of blending and layering, and to the knowledge of unsuccessful attempts. Past work often defined a potentially successful mix in terms of the ratio of net-acid-neutralizing rock to net-acid-generating rock. For example, one case study indicated the bulk pile-wide ratio was approximately 3: 1. Since this exceeded a common ratio used in acid-base accounting, no acidic drainage was predicted. However, acidic drainage appeared within two years. A large part of the ambiguity in mixing arises from attempts to predict success based on a ratio. This paper looks in detail at simple discrete-zone mixing, where at least one truckload of NAG rock is placed in a particular location with no further rehandling or dozing. The lack of acidic drainage in this scenario is dependent on the intervening distance between the discrete NAG zones, along flowpaths occupied by NAN rock. Calculations show that the bulk mixing ratio of a mined-rock pile is not an accurate indication of whether near-neutral drainage can be maintained. For example, a pile with a bulk ratio around 300: 1 could still release some acidic drainage. Calculations also show that the minimum separation distance of the NAG zones (L) can be so great, even with typical NAG and NAN rock, that the mixed pile could safely contain only a few percent of NAG rock, which would not be sufficient for many minesites with NAG rock. The comparison to a more elaborate, computer-based statistical model shows that the simple discrete-zone approach will provide a reliable yes-no indication of whether any acidic drainage will leave a pile. However, predictions of whether combined downstream drainages will be acidic depend on numerous site-specific physical and geochemical factors within and below a pile that cannot be modelled in a general way, like the number of flowpaths and the nature of their intersections.

Jan 1, 2000

By M. A. ENCINAS-ROMERO, G. TIBURCIO-MUNIVE, P. GUERRERO-GERMÁN, M. M. SALAZAR-CAMPOY, J. L. Valenzuela-García, L. S. QUIRÓZ-CASTILLO, J. R. PARGA-TORRES

Simultaneous alkaline pressure oxidation and sodium cyanide leaching treatments on a pyritic ore from Mulatos Mine located in Sahuaripa, Sonora, Mexico, were carried out. Mineral characterization, agitated leaching, hot cyanidation under atmospheric pressure conditions, simultaneous moderated pressure oxidation and leaching, and kinetic tests results are shown. The modified variables were temperature, pressure, and cyanide concentration. Characterization indicated that pyrite was the main mineral. Simultaneous pressure oxidation and leaching experiments were conducted in a temperature range of 40 to 80 °C, an oxygen pressure range of 87.5 to 200 psi, and cyanide concentration range of 0.8 to 1.2 weight percent in a 2-L Parr pressure reactor. Dissolution rates of 81 to 86 percent were achieved under the following conditions: 87.5 psi, 80 °C, 0.8 weight percent NaCN and processing time of one hour.

By W. A. Van Dyk

Hydrophobic particles with diameters between 1 and 3 mm are poorly recovered by conventional flotation techniques. A novel reverse flotation technique is described whereby coarse particles with surfaces rendered highly hydrophobic, repel the bubble films in a froth and thus drop through the froth under gravity, to be recovered as a sink product. Conversely, gangue or hydrophilic particles are supported by the bubble films in the froth and are therefore recovered as a floating product. Tracer tests were conducted in the cell in order to study the dynamic behaviour of solid particles in the froth. The effects of hydrophobicity, density, particle size and particle shape were investigated experimentally. The higher the hydrophobicity of the particles, the lower the recovery of particles as a floating product, while the recovery of particles as a sink product increases with an increase in particle density. Furthermore, a decrease in particle size results in an increase recovery of hydrophobic particles as a floating product. When treating particles of the same mass-to-surface-area ratio in the froth, flat particles would be recovered as a floating product in preference to cubic, disc-shaped, cylindrical and spherical particles, in that order.

Jan 1, 1995