Search Documents

By W. C. Meyer

A physical model of flotation, derived from viewing froth as a kinetic species since it constitutes the carrier of ore particles, not only agrees with and is simulated by engineering math models, but is statistically verified by actual laboratory flotation data. The model couples the mechanical removal of froth using paddles with the more rapid chemical interactions taking place in the bath. It clearly shows that the kinetics of mass removal is dictated by flotation cell dimensions, paddle speed, and, more importantly, froth characteristics. Some conclusions and predictions of the model are presented.

Jan 1, 1982

By T. M. Gurr

The United States is the world's leading producer of phosphate rock. In 1975 according to the U. S. Bureau of Mines' statistics, 44.3 million tonnes (48.8 million short tons) of phosphate rock were produced in the United States', which is 40.6 percent of the world's production2. The major phosphate producing areas of the United States are located in Figure 1 and the production for 1975 is listed as follows: Million Million Short Tonnes Tons Florida and North Carolina 36.9 40.7 Western States 5.3 5.8 Tennessee 2.1 2.3 All of these areas produce phosphate from deposits which are sedimentary marine in origin. Occurrences of phosphate exist throughout the United States in numerous locations that are of both igneous and sedimentary origins. However, these other phosphate occurrences vary greatly in extent and economic significance. Georgia, South Carolina, California, Texas, Arkansas, Kansas, Iowa, Alabama, Kentucky and Virginia are but a few of the states in which phosphate is thought or known to

Jan 1, 1977

By David Oliveira

"INTRODUCTIONOne of the key drivers for the selection of a mechanized tunneling method in good quality rock masses is a good excavation advance rate. In order to achieve satisfactory advance rates, a good geotechnical performance of the rock grippers in main beam open tunnel boring machines (TBM) is required, besides other factors related to ground support and the performance of the cutter head.One well known potential issue of main beam gripper TBM is associated with the bearing capacity of the tunnel side walls while crossing fault zones or poor rock masses in general. Such a mechanism is similar to that of footings on rock and perhaps the most common problem associated with gripper performance. Depending on the quality of the rock, the rock under the gripper contact may experience significant damage and crushing (Figure 1), eventually affecting the TBM advance rate due to a lack of tunnel wall reaction/support. Such a mechanism is primarily dependent on rock quality, applied loads and gripper size.In the case of large diameter TBMs (e.g., D > 12 m), a second potential failure mechanism may arise associated with the loss of confinement within a rock pillar between twin tunnels, even in good quality rock but particularly in bedded sedimentary strata. Punching of the rock pillar may develop due to excessive shear along bedding partings and sub-vertical joints (Figure 2), particularly under a low stress environment. As a result, this mechanism is dependent on both the rock pillar width between twin tunnels and stress conditions around the tunnels, in addition to the previous factors described for the first failure mechanism."

Jan 1, 2016

By J. Rostami, P. P. Nelson, A. Khetwaln

Tunnel boring machines (TBMs) can be considered as the method of choice for tunneling in many projects due to the high level of efficiency and high potential productivity, safety, and applicability in a variety of subsurface conditions. The muck transportation system in a TBM tunneling operation plays a significant role in the process and impacts the overall performance of the machine. This paper introduces a recently developed method of simulating TBM operation through discrete event simulation (DES), which allows for tracking of the various activities, incurred downtimes in the operations, and overall machine utilization. The study presented here compares two different muck transportation systems, conveyor and rail, under similar geological conditions to quantify the impacts of the choice of muck transportation systems on machine utilization. The results show the applicability and extent of redundancy in the use of the two systems relative to machine capabilities and their sensitivity to geological conditions.

Jun 13, 2021

By Fredrick C. Kruger

We can confidently predict such obvious long-term trends affecting the minerals industry as - increasing consumption, exhaustion of easily discovered near-surface ores, and sharp limitations upon open pit mining by environmental considerations. There- fore, we must intensify the exploration for, and the development and exploitation of, deep bodies of potash and other ores. This paper examines the state of the art of the search for, and the evaluation of, potash from both a geological bias and a mining practicability. The use of indirect geological methods and geophysical techniques, followed by expensive deep drilling, are the conventional approach to evaluation and development of mining plans. The geologist and the geophysicist will have to find ways to perform both of these tasks better and cheaper.

Jan 1, 1973

By Dirk van Zyl, Lysa Morishita

Mining companies are increasingly approaching the social aspect of sustainable development within the rural communities that neighbour their projects and operations. Rural community engagement requires significant effort and resources, and it can be extremely challenging for mining companies to earn and sustain social capital. The focus on rural, proximal community engagement is not to be understated and has led to significant benefits in many communities. However, opposition to mining projects is often exhibited in urban environments, where there may be potential for mining companies to gain social capital with relative ease. Cities tend to have existing frameworks for community engagement and public activation, such as annual parades and festivals, that make it easy for a mining company to provide financial support or value-in-kind. Local organizations and community groups can achieve the same amount of engagement in an urban environment with significantly less effort required from the mining company. By applying simple marketing principles to community engagement strategies, corporations can increase awareness for their business and encourage city residents to think critically about the origin of resources. Unlike many corporations, mining companies are not marketing or selling products to individual consumers. From this arises the opportunity for a company to use marketing to promote other positive initiatives and, as such, connect their brand with positive messaging thus earning social capital. This may lead to a wide variety of secondary impacts including benefits to recruitment efforts, increased political support, and positive media coverage. This paper explores these matters with special reference to Vancouver, BC, Canada and the mining companies Teck and Goldcorp.

Jan 1, 2017

By D. J. Barratt

What is meant by "Minimizing Risk"? This paper explores some of the factors encountered in plant design which can affect the success of a mineral processing plant in terms of its planned output, quality of product and recovery. Any deficiency in either one of these objectives means lost revenue at the start of a project and reduced present value for the mine life. Time is money. Related factors such as project conception, feasibility studies, capital cost and operating cost estimation and mining studies have been covered in a recent paper (1) from which material for this paper has been drawn. What follows is a discussion of the principal factors which can influence the success of a project with particular emphasis placed on processing concepts.

Jan 1, 1983

By W. C. Baver

Even before the energy crisis developed in the early '70's, considerable research world-wide was being directed towards the development of schemes to both reduce the energy requirements and to reduce air pollution emissions associated with the manufacture of glass. In many cases the sought-for solutions would benefit both objectives. If, for example, the glass batch could be consolidated into such compact forms as briquettes or pellets, they could be preheated in a moving-bed heat exchanger with the high-temperature exhaust gases from the glass furnace. Lower furnace temperatures would thus be possible with a corresponding reduction in heat losses and total fuel consumption. Moreover, the lower temperatures would also reduce the amount of nitrogen oxides generated in the furnace and emitted to the atmosphere. Many tests on consolidated glass batch have been run in many countries. In some cases, extended tests on production furnaces have also been included in the programs. For various reasons, however, none of these has proved to be economically attractive. The current, but temporary lull in the rapidly rising cost of energy which has been with us in recent years, has reduced the push for research for energy saving means for melting glass. A few of the current programs will be discussed. Since raw material requirements, primarily physical in nature, are affected by some of these schemes, these will also be considered.

Jan 1, 1986

By W. W. Wen

Approximately 3 percent of the raw coal processed in U. S. Steel coal-preparation plants ultimately reports to slurry- tailing disposal. The usual disposal method is to pump the refuse slurry containing the minus-48 mesh (300 µm) refuse into dams or impoundments that are constructed of the coarse refuse. The failure of an impoundment at Buffalo Creek, Saunders, West Virginia and the sliding failure of a coarse refuse pile at Aberfan, Wales, England, resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of Federal regulations dealing with the construction, operation, and final abandonment of coal refuse disposal areas. As a consequence of these regulations the use of the landfill/impoundment method of disposal became in some cases economically urlfeasible or technically impossible. U, S. Steel has studied a number of alternative methods of refuse disposal. During an investigation of mechanical dewatering with a pressure filter, Portland cement was added to the slurry to solidify the filter cake. Because of the success of the cement addition it was decided to study the stabilization of fine-coal-refuse slurry through use of cement-type additives.

Jan 1, 1979

By A. J. Basu

Rock mass properties testing for determining strength parameters is an integral part of geomechanics. These tests are performed either in a laboratory environment or in a field (in-situ). The authors share their experience in using numerical modelling in simulating the laboratory test procedures. This approach helps studying the rock breakage and failure mechanism more efficiently and provides a high degree of visualization. Moreover, imperfections and discontinuities can be easily incorporated in these models. This capability of providing arbitrary fractures and discontinuities facilitates in building a large knowledgebase of rock strength and failure mechanisms. This knowledgebase may then be used to generate heuristics for determining rock strengths for rock mass with fractures and discontinuities.

Jan 1, 1997

By Tom H. W. Loomis

The department of the Interior is a federation or holding company of several fiercely independent bureaus which have either jurisdiction or expertise - or both - in a wide range of environmental fields. Each bureau is an advocate for its own concerns and an enforcer of its own mandates. This can be confusing to the company operating in the field. I will try to explain our concerns, help you see where we are "coming from," and give you some insight as to how we can help you. Other speakers have stressed the environmental concerns and site selection factors for uranium wastes so I will focus on the concerns of the Department of the Interior and some of the assistance we can give you in this area People are more aware and more concerned about environmental factors now than they used to be. Thus the past decade has brought about an evolution in both siting and design of uranium mill tailings ponds. Site selection criteria used to be simple - find a tract of land as near to the ore supply as possible with enough space and suitable topography for the expected volume of wastes. Site selections in the past have left a legacy of problems to be corrected - radioactive wastes on stream banks and in floodplains, mill wastes in and near established communities, and unprotected wastes subject to constant erosion. This is no longer acceptable environmentally or socially to a newly aware and concerned public. (Series of 30-35 slides showing uranium mine and mill wastes in Western United States. These illustrate environmental problems, reclamation and environmentally acceptable sites. The first group of slides are aerial shots taken in Wyoming and shows a surface mine and mill area. In the various views the pit, overburden piles, mill, and tailings pond can be seen. The next series were taken in Wyoming and New Mexico. These show various views

Jan 1, 1980

By G. E. McCormack

The Development of Water Gel Explosives Water gels are the most recent development in the evolution of commercial explosives. They are replacing dynamite, having proven themselves to be excellent alternatives to this standard explosive. Water gels have steadily displaced dynamite over the past two decades. In 1959, they accounted for only 1 percent of the market they share with dynamite. By 1965, the share taken by water gels had grown to 21 percent. In 1970, it was more than 40 percent, and today it is nearly 70 percent. Black powder, the first widely used explosive, revolutionized mining and quarrying in its day. However, when nitroglycerin dynamite became available about a century ago, it rapidly displaced black powder because it provided greater energy for a given weight, much higher velocity for better rock shattering performance, and water resistance for easy use in wet conditions. During the past 50 years, ammonium nitrate has played a dramatically increasing role in explosives. First, it was used as an ingredient in dynamite, and then as the main component in nitrocarbonitrate blasting agents. About a quarter of a century ago, it began to find use in a simple and inexpensive mixture with fuel oil that has revolutionized the explosives industry and today fills about 80 percent of the requirements for explosives in the U.S., and certainly the bulk of blasting requirements worldwide. Water gels and dynamites share the remaining 20 percent. Water gel explosives based on ammonium nitrate have also been developed during the past quarter century. These explosives contain

Jan 1, 1979

By George S. Austin

Perlite is rhyolitic glass with 2 to 5 percent by weight (wt.%) bound water held within the silicic-glass structure. It is often distinguished by vitreous, pearly luster and concentric perlitic fractures ("onionskin"). Occurrences worldwide are associated with Tertiary to middle Quaternary volcanic rocks. Perlite is in silicic domes, plugs, laccoliths, flows, vitric tephra, chill margins of dikes and sills, and welded ash-flow tuffs. It is a hydrated volcanic glass formed through secondary alteration of obsidian by the incorporation of water into the glass/silica structure. Post-emplacement hydration (weathering) of cooled glasses by meteoric water is the principal alteration process, but some hydration by magmatic or meteoric water during or shortly after emplacement, or hydration by water exsolved during cooling may occur. Commercial "perlite" is any volcanic glass that expands or "pops" when heated quickly to plasticity while evolving steam and thus forming a lightweight, frothy material. The expansion temperature typically ranges from 1,100 to 1,500°F. An expanded volume increase of 10 to 40 times the original volume yields expanded densities of 1.5 to 11 pounds per cubic foot (lbs/ft3). Perlite is mined by eight companies at 10 operations in six western states. New Mexico accounts for more than 80% of the total tonnage mined. The rest comes from Arizona, California, Colorado, Idaho, and Nevada. In 1992, domestic production was 571,000 short tons (st), domestic apparent consumption was 591,000 st, and the value of crude perlite was $15.3 million. In 1991, with about the same production and price of crude perlite, the gross value for expanded perlite was $101.7 million. Perlite exports in 1992, primarily to Canada, are estimated an 30,000 st; and imports, from Greece, are an estimated 50,000 st. In 1992, 70 plants in 33 states expanded crude perlite. Construction uses of expanded perlite accounted for 66% of total domestic sales. Expanded perlite used as filter aid accounted for 15%. All other markets, including use as a filler and in agriculture, accounted for 19%. Leading states for expanding perlite, ranked by order of sales, were Mississippi, Pennsylvania, California, Illinois, and Georgia. Domestic perlite encounters transportation disadvantages in some areas of the eastern United States compared to perlite imported from Greece. However, western U.S. perlite exports to Canada offset this in large part, and net import reliance for perlite is about 3% of domestic consumption. Perlite grab samples were tested at the New Mexico Bureau of Mines and Minerals Resources (NMBMMR) for their basic suitability in horticulture, construction, filter aids, and fillers/extenders using Perlite Institute techniques modified by the NMBMMR. Most commercial perlite ranged from 2.5 to 3.0 wt.% bound water for all major types (classical, granular, and pumiceous). Expanded density varied widely, but the lowest density of 1.9 lbs/ft3 was for granular. Average brightness of expanded perlite was 47.6 to 69.3%. Nonexpansibles, commonly obsidian or "dead" perlite, ranged from 18 wt.% to less than 1 wt.%, with granular perlte generally the lowest. Compacted density was not related to either perlite type or nonexpansibles present. Sieve analyses of the -50+100 mesh product showed that, in general, pumiceous perlite produces more fines and classical and granular perlite average 60 to 80% -30+100 mesh after expansion. Samples were tested for crystalline silica that ranged from below the detection limit of 0.5 wt.% to nearly 0.2 wt.%, but most tested below 0.5 wt.%. Although quartz content can be lowered in the expanded product by the expansion process, producers can further lower crystalline silica in the product by mixing low-quartz crude with high-quartz perlite before expansion. Chemical analysis by x-ray fluorescence confirms the rhyolitic composition of perlite, but indicates that surface weathering may increase the concentration of some elements, such as potassium and calcium, by infilling cracks or fissures developed during or after perlite emplacement.

Jan 1, 1995

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

Ground water inflow into a mine and the re¬sultant impact on district hydrology can be pre¬dicted on a site specific basis once the ground water flow systems at the site are sufficiently well under¬stood so that a valid conceptual model can be de¬veloped. Ground water flow systems are controlled by the hydrogeologic properties of the materials at the, site, including hydraulic continuity along flow paths, and boundary conditions. Preliminary delin¬eation of hydrostratigraphic units for conceptual models frequently can be based on surface water data; specifically, spring locations and the gain-loss reaches of streams. Quantitative predictions of mine water inflow and its impact on regional hydrology require col¬lection and analysis of numerous types of data. Hydraulic conductivity must be defined quantita¬tively both parallel and perpendicular to bedding as well as areally for each hydrostratigraphic unit. The characteristics of the Davis shale in case his¬tory number 2 illustrate this concept very well. The storage characteristics also must be determined for each hydrostratigraphic unit and the potential or hydrostatic head should be quantified vertically and areally for each unit. The potentiometric measure¬ments in the Bonneterre Formation as discussed in case history number 2 illustrate this point. The data collection and data analysis techniques constitute the weak link in the analysis of mine inflow and district impact. The technology for char¬acterizing a mine site in the field has lagged behind the technology for mathematical simulation; we at¬tribute this development to the fact that computer modeling is relatively inexpensive compared to field data collection and analysis. On-site tests provide the best means of quan¬tifying hydraulic conductivity parallel to bedding and the storage characteristics of the unit. Pump tests with multiple observation wells provide the best information from on site tests. Hydrogeologie boundaries can be located from such multiple well tests. Multiport piezometers provide a means for determining the vertical potential in a single borehole. Borehole geophysics can facilitate the def¬inition of hydrostratigraphic units. Vertical hy¬draulic conductivity is difficult but not impossible to quantify with existing field test methods; labo¬ratory tests of cores fail to give a value represent¬ative of the field situation. The storage characteristics of a confined (artesian) hydro¬stratigraphic unit can be difficult to quantify when pumping changes the confined unit to an uncon¬fined (water table) case after depressurization and dewatering. Transmissivity and storage coefficient can be approximated to some extent for given field con¬ditions by computer modeling if enough is known about hydrogeologic boundaries. Modeling can be used in a trial-and-error approach to match transmissivity and storage coefficients to existing water level data corresponding to estimated discharge rates. A solution can also be obtained using a tech¬nique referred to as the inverse method. Unfortu¬nately, such a solution is seldom unique. Fracture flow models exist but practicality usu¬ally necessitates reversion to a basic Darcy flow model. Data requirements for fracture flow models could be difficult to fulfill where fracture aperture, spacing, orientation, and length are required. Ob¬taining such data at depth prior to mining would be impossible for any mine simulation in fractured media. We are of the opinion that most fractured media simulations can be accomplished using con¬ventional Darcy flow models by viewing the field problem on a macroscopic scale. The real challenge is to delineate hydrostratigraphic units properly in the field. The question of whether a broken-up fault zone is an aquifer or a barrier boundary is seldom simple. The fractures usually can be treated as an equivalent porous medium in either case. Only a few techniques exist for predicting un¬derground mine water inflow. These techniques fre¬quently are designed to evaluate shaft or tunnel inflow under steady-state head conditions in a sin¬gle layer rather than in multiple hydrostratigraphic units. Few computer programs exist that have the

Jan 1, 1986

By R. S. Hearon

The image of the open-pit miner in the eyes or the Environmentalist has never been very outstanding. The phosphate industry, whose history in Florida reaches back to the late 1800's, can-not be credited until recently with a large number or accomplishments in terms of protection or the environment to change this image. This lack of action was not deliberate or in opposition with the desires of the public. In the formative years, there was little or no public and the companies found it necessary to build towns to house their employees and their families, towns which remained in existence until the late 50's and early 60's or formed the core of present large communities. Neither these pioneers nor most subsequent resource developers considered themselves un-thinking spoilers, nor were they so regarded by their contemporaries. Instead, they acted in a manner consistent with their environmental circumstances and intellectual heritage. Early Americans did make mistakes in using the land but the mistakes became apparent only in the opinion of later generations. Over the past five to ten years, there has been a new self-awareness in the industry with regard to environmental responsibilities brought about, in part by a continuing onslaught of new regulations with jurisdiction over our activities. Part of the new regulations are aimed at industries as a whole while many, particularly state regulations, pertain specifically to the phosphate mining industry. Why all the new regulations? The reasons are encased in a complex web of activity but stem primarily from a new public awareness of its environment. More and more of our youth have become interested in the environmental science areas such as biology and ecology. The tremendous growth rate in both the population and industry has made personal issues out of subjects such as atmospheric inversions and water shortages which previously were abstract concepts. The State has grown from a population of 1,500,000 in 1930 to approximately 9,000,000 people today. This personal impact and general lack of knowledge on the part of the public concerning economics has resulted in big business no longer being held in awe, often in contempt and generally in suspicion where environmental concerns are encountered.

Jan 1, 1978

By Wang Ding-heng, Wang Zhi-yuan, Nolan B. Aughenbaugh

The People's Republic of China has abundant coal resources with proven reserves amounting to 582 Gt (641 billion st). Recognizing coal as a major energy source on which to build the country's industrial and economic base, there has been a rapid increase in production since the founding of the People's Republic. In 1949, only 29.4 Mt (32.4 million st) of coal was mined. Production has increased to 576.5 Mt (635.5 million st), exclusive of Taiwan, at present, making China the third largest coal producing country in the world. Plans call for a 4-5% increase in annual production for the next 20 years. Coal constitutes 70% of the primary energy consumption in China. The remaining 30% is divided between petroleum and natural gas with 26% and hydropower with 4%. Coal use and consumption is divided as follows. General industrial use comprised 48.9%, power generation uses 20.1%, and coking accounts for 10.5% (6.3% for metallurgy and 4.2% for chemical industry). Domestic use such as home heating and cooking makes up 17.8% and coal-fired steam engines for railways uses 4.7%. Coal Districts Coal underlies about 1/18 of China's land area. It occurs in 30 provinces, autonomous regions, and municipalities. In addition, the western interior region, which has not been explored, may contain sizable reserves. Based on geology, geography, and administration, the coal fields can be grouped into five districts as shown in Fig. 1. The north China district, the heart of the industrial base for the country, has the most extensive and largest deposits of the five districts. This amounts to almost 40% of the country's total reserves. The largest coal basin with proven reserves of 181.4 Gt (200 billion st) and the most exploitable seams is located some 300 km (186 miles) southwest of Beijing (Peking) in Shanxi Province. Centered around Taiyuan, the compound field extends from Datong in the north to Xian in the south. Its western extension is not known fully. The Northwest and Northeast districts contain the second and third largest deposits. The biggest coal field in South China is located in the Sichuan and Guizhou Provinces near Chongqing. At present, it is not known if sizable coal measures exist in the Tibetan district. Coal Types China's coal varies widely both in age and rank. Geologically, coal measures were deposited from the lower Carboniferous (Pennsylvanian of the US) and Permian of late Paleozoic, mainly during the Jurassic of the Mesozoic and peri¬odically throughout the Cenozoic. Collectively, coal from the lower Carboniferous, Permian, and Ju-

Jan 3, 1983

By C. I. Richman

The E h potential during of a iron reducing bacteria such as Aquaspirillum Magnetotacticum (A.M.) can be predicted by a growth model. It also reflects the adsorption of Fe+2 Cu+2 and Mn +2 ions, that can be incorporated into magnetic material called magnetosomes. The Ferric ion concentration during controlled growth of Thiobacillus Ferrooxidans (T.F.) is a function of the bacteria population curve, while A. M. ferrous ion concentration is a function of the integral of the population curve. Charting of the redox potential of T.F. during batch oxidation of refractory ores such as pyrite and pyrrhotite can be helpful to establishing onset and rate the bulk bio-oxidation rate. The onset of biooxidation is marked by an increase in Fe +3 ions that can be correlated with increased growth due to adsorbed electrons.

Jan 1, 1998

By Gene Mattila

Each installed rock bolt costs in excess of 520.00. High cost in conjunction with the primary purpose of safety makes it only logical to install the highest quality anchors possible. Each bolt has designed support capabilities in axial, shear and fluctuating ground condition, if installed to manufacturers recommendations. The quality of anchor is not; however, only affected by material specifications, but by transportation, handling storage, installation procedure, machine performance and geology. The quality is not only affected by many variables, but reliability should be assured. Non-destructive methods of testing reliability are only available for several types of bolts.

Jan 1, 1985

By H. Sevim

Placement of coal combustion byproducts into abandoned sections of underground coal mines for the purpose of subsidence mitigation has been investigated in Illinois. Several handling and transportation systems have been examined. Prototype pneumatic and hydraulic placement systems have been developed and demonstrated. The demonstration site, Peabody No. 10 mine in Pawnee Illinois, is selected as a case study. It is found that, for a project of 5 years, transporting 150,000 tons of byproduct annually from a power plant located 32 km (20 miles) to the mine would cost $1.80 per ton and placement into underground would cost $3.07 per ton.

Jan 1, 1998

"INTRODUCTION Twin Metals Minnesota (TMM) (operating as a joint venture between Duluth Metals and Antofagasta PLC) assumed control of the property in 2010. Amec became involved with the project in 2011 and in 2012 incorporated additional drilling in order to update historic resource estimates. The Maturi geological model and resource estimate was updated in 2014 to incorporate additional information obtained during 2013 and 2014 drill campaigns. In 2017, Amec was purchased by the Wood Group and is now known as Wood. Geology The Twin Metals Minnesota (TMM) Maturi, Maturi Southwest, Birch Lake, and Spruce Road properties are located in northeastern Minnesota (Figure 1). This talk discussed the Maturi deposit only, although all four deposits share similarities. The following geology is summarized from Peterson and Severson (2002).Maturi lies within the Superior Province of the Canadian Shield which is exposed in central and northeastern Minnesota and extends northward into Ontario. In eastern Minnesota, the Midcontinent Rift System developed during crustal scale extension in the Mesoproterozoic Era. The rift system is traceable, as exposures of mantle-derived tholeiitic to subalkaline mafic lava flows, intrusives, and rift-filling fluvial sedimentary rocks, and in the subsurface as a gravity anomaly (high), from the eastern end of Lake Superior, arcing west across the lake basin, and extending south-southwest to northeastern Kansas. Intrusion of the Duluth Complex, circa 1,108 - 1,099 Ma, was related to rifting and is co-genetic with the North Shore Volcanic Group mafic volcanic rocks that form the hanging wall of the Duluth Complex to the east. Cu-Ni-precious metals (PM) mineralization including Pt, Pd, Au and Ag within the Duluth Complex is hosted by mafic to ultramafic intrusive rocks that are part of the overall intrusive complex. The Duluth Complex is defined as a more or less continuous mass of mafic to felsic plutonic rocks that extends northeastward for more than 170 miles (275 km) in an arcuate fashion from Duluth nearly to Grand Portage in Minnesota. It is bounded by a footwall of Paleoproterozoic sedimentary rocks and Archean granite-greenstone terranes (Peterson and Severson, 2002), and a hanging wall largely of comagmatic anorthosite, rift related flood basalts, and hypabyssal intrusions of the Beaver Bay Complex. Mineralization is hosted in the basal mineralized zone (BMZ) of the South Kawishiwi Intrusion (SKI). The SKI magmas intruded sub-horizontally between hangingwall Anorthositic Series (AN) rocks and footwall granitic rocks of the Neoarchean Giants Range batholith (GRB). The Maturi local geology and the deposit footprint (shaded orange) is shown in Figure 2."

Jan 1, 2018