Search Documents

By Omar A. Muhtadi

6.1 INTRODUCTION The three most critical factors in successful heap leaching operations are: • The methods employed to pretreat ore (i.e, crushing and agglomeration); • Placement of ore on the leach pad (heap building techniques); and • Wetting of the ore with cyanide (solution application techniques). Improper execution of any of these initial steps may result in a substantial sacrifice of total metal extraction or, in the worst case, in project failure. Ore preparation in terms of crushing and agglomeration was discussed in Chapter 5; this chapter therefore focuses on commonly employed techniques for heap construction and solution application. The main objective of heap construction is to obtain the most homogeneous heap possible. "Channeling" of leachate in heaps with preferential seepage paths leads to preferential leachate distribution and uneven/incomplete extraction. The two main contributing causes of channeling are inadequate attention to heap construction and uneven solution application. These pitfall s can best be avoided through a knowledge of the various techniques available and the applicability and success of these techniques with various ore types and site conditions. The remainder of this chapter provides a discussion on these two subjects. 6.2 HEAP BUILDING TECHNIQUES Successful heap building techniques vary with the type of ore and, since no two orebodies are exactly alike, some slight modifications are usually necessary for each specific project. However, it is possible to generalize in terms of the appropriate techniques to be used with ores having similar characteristics. This section discusses the three most commonly used methods of heap construction and provides some guidelines with regard to ore types, construction constraints, and lift height parameters for each of the three. 6.2.1 Run-of-Mine Dumping and Dozing The run-of-mine method of heap building can only be used with ore of a highly silicious nature (i.e., ore which will not generate a large amount of

Jan 1, 1988

By J. Swensen, R. Brandon, A. Wallstein, S. Bessinger, J. Pile

It is generally agreed that C.C. White was the first to describe and market coal mine roof trusses beginning as early as 1967. White was issued a patent in 1969 1. Coal mine roof trusses were extensively used in the 1970’s, and their use has proven valuable in many difficult conditions. Beginning in the mid 1990’s, several types of bar/cable trusses have been introduced. A new and innovative bar/cable truss recently introduced offers several advantages. By eliminating many small parts, and simplifying the installation, these new trusses are much easier and faster to install, thereby increasing operator safety.

Jan 1, 2004

By Jeff Salai

The CP-3A contract is the final segment of the MWWST’s 28.3 km (17.6 mile)pressurized water supply tunnel for the metropolitan Boston area. The 1,288 m (4,226 feet) of U-shaped tunnel alignment passed through five rock zones employing four different primary support systems. The short tunnel began in Weston, Massachusetts, at Shaft 5A in soft, completely weathered argillite, passed through a fault zone, and ended in Dedham granite. An 18-foot diameter horseshoe starter tunnel was built to accommodate a 4.94 m (16-foot 2 1 / 2 inch) diameter Robbins TBM. Heavy water inflows were anticipated and subsequently encountered during probe drilling. Pre-excavation grouting was implemented at high pressures to displace high water inflows in the starter tunnel and consolidate the fault zone. This paper will provide an overview of the tunnel construction with an emphasis on ground control, grouting and survey control.

Jan 1, 2001

By E. Steiakakis

This paper presents in detail the procedures followed and the results obtained in order to determine the stiffness parameters of the calcareous marls found in the lignite mines in Ptolemais, Northern Greece. Triaxial tests were performed on representative samples of the inner burden marl and the marl which underlies the lignite bearing series of the region. The tests were conducted under drained conditions, with controlled loading (including an unloading-reloading loop), while the axial strain was measured externally as well as with displacement transducers mounted directly on the specimen (Hall Effect sensors). The geotechnical parameters obtained (i.e., cohesion, angle of friction, stiffness modulus, stress-strain relationship), were subsequently used for simulating the triaxial testing with the Plaxis finite element software. Simulation results are in good agreement with the experimental results. The resulting material model can then be applied to modeling the mobility that is expressed during the excavation of the open pit mines.

Jan 1, 2005

By T. J. van der Walt

This paper proposes a new methodology to model ill- defined processing operations using neural nets (NN's). A process with many variables (large dimensionality) cannot be modelled adequately if limited process data are available. This problem of multi-dimensionality is addressed and an approach suggested to reduce the dimensionality using NN's. The result of this modelling methodology is a combined model of phenomenological expressions and NN's. The model can successfully be incorporated in a dynamic simulator of the process. A new approach to conduct modelling on the basis of continuous data collected directly from an industrial processing unit, is also proposed. The modelling methodology is applied to a typical processing operation, the resin-in-pulp (RIP) process.

Jan 1, 1992

By William T. Jr. Renfroe, Donald C. Gipe

INTRODUCTION Historically, pollution control in the metal-ore mining industry has been very limited. Unless mine water contained large quantities of solids, it was generally discharged without any treatment. If treatment was used to control solids, it was principally the provision of a settling basin in the form of a tailings impoundment used in conjunction with an associated metal ore dressing facility. Recently, however, a growing awareness of the adverse environmental impacts of mine drainage, coupled with strict environmental laws, has prompted the mining industry to look at new technologies and to refine the existing methods to further treat the wastes generated. This industry is unique in that waste loadings are extremely variable, and a "typical facility with typical waste loads" does not exist. Consequently, one waste- water treatment system cannot be utilized on an industry wide basis; rather, each treatment system must be designed specifically for the pollutants in each individual discharge. Public Law 92-500, the Federal Water Pollution Control Act (FWPCA) Amendments of 1972, became effective on Oct. 18, 1972. This law completely restructured Federal laws and philosophies underlying the Federal approach to water pollution control. Prior to the 1972 amendments, the principal Federal regulatory tool had been water-quality standards based on a designated use for a particular body of water. The concept was that waste disposal into water bodies is a desirable and acceptable use of the water body if it does not interfere with other beneficial uses. This had the effect of requiring various degrees of treatment and, consequently, various economic hardships on industries de- pendent upon their location. In many waterways. it is very difficult to quantitatively relate discharges to water quality. The 1972 amendments changed the basic philosophy, as stated in the Senate Committee report on the bill, to ". . . no one has the right to pollute . . . that pollution continues because of technological limits, not because of any inherent right to use the nation's waterways for the purpose of disposing of wastes." Pursuant to Sections 301, 304(b), and 306 of the FWPCA Amendments of 1972, the US Environmental Protection Agency (EPA) was required to establish effluent standards applicable to all industrial discharges. These standards must be based upon the application of the "best practicable control technology currently avail- able" (BPT) and the application of the "best available technology economically achievable" (BAT). The BPT and BAT levels must be achieved industry-wide by July 1, 1977, and July 1, 1983, respectively. WASTE SOURCES The waste-water situation in the mining segment of the ore mining and dressing industry is unlike that encountered in most other industries. Most industries (e.g., the milling segment of this industry) utilize water in the specific processes they employ. This water frequently becomes contaminated during the process and must be treated prior to discharge. However, in the mining segment, process water normally is not utilized in the actual mining of ores (exceptions are hydraulic mining operations and dust control), but it is a natural occurrence that interferes with mining activities and must be removed before mining can commence. Water enters mines by ground-water infiltration and surface runoff, and it comes into contact with materials in the host rock, ore, and overburden. The underground mine must pump large quantities of ground water to prevent flooding of the mine. Water from surface mining operations generally occurs as a result of surface runoff of rainwater. Generally, mining operations control surface runoff through the use of diversion ditching and grading to prevent, as much as possible, excess water from entering the working area. Nevertheless, some surface runoff does come into contact with the working area and may become contaminated. The quantity of water from an .ore mine is unrelated, or only indirectly related, to production quantities. De- pending upon its quality, the mine water may require treatment before it can be discharged into the surface drainage network. The variability of water quality from mines can best be demonstrated by looking at Table 1. This table shows the range of pollutant concentrations in untreated discharges from three different categories of mines (as categorized by EPA in the development of BPT and BAT effluent standards for the metal-mining industry). Data for this table were obtained during EPA's preparation of effluent standards for this industry. The parameters shown on the table are the pollutant parameters of primary interest in this industry; blanks in the table indicate that data were not available, and the parameter is not expected to be present in significant quantities. Other pollutant parameters are present in mining waste water, but they are either incidentally removed in the treatment process or are found only in trace amounts. The three categories comprise more than 90% of the metal production value in the United States and approximately 95% of the total mine discharges. It is important to note that not all parameters are found in significant concentrations at all locations. IMPACT ON WATER QUALITY One of the most troublesome mine-drainage problems is acidity. Although generally associated with coal mining, acid mine drainage frequently occurs from other types of mines. Although the exact mechanism of acid mine drainage is not fully understood, it generally is believed that pyrite (iron sulfide, FeS,) is oxidized by oxygen (Eq. 1) or ferric iron (Eq. 2) to produce ferrous sulfate (FeSO4) and sulfuric acid (H2SO4) . The mining of ores associated with pyritic material exposes the pyrites to water and oxygen and grossly accelerates the natural oxidation processes, resulting in the significant production of acid mine drainage.

Jan 1, 1982

By Robert D. Norris

Heap leaching provides a method of economically recovering gold from low grade ores with low capital and reasonable operating costs. As with conventional methods, alkaline cyanide solutions are used for leaching. Since gold (and silver) is (are) present as the native metals, oxygen (as air) is required to oxidatively complex the metals with the cyanide. Oxygen depletion can readily occur adversely affecting recovery. The addition of low levels of hydrogen peroxide during leaching can lead to significant increases in both rate of recovery and total recovery. This process allows for the use of shorter pad times or deeper heaps and increases the gold (silver) concentration to the recovery circuit and thus can reduce cyanide losses by virtue of permitting the use of less total leach solution per ton of ore processed.

Jan 1, 1983

By Stephen G. Hardcastle, Michel G. Grenier, Kevin C. Butler

Today there are numerous electronic rotating vane and thermal (hot-wire) anemometers, as well as vortex meters available to measure air velocity. Of these, a laboratory and field evaluation has found that certain instruments are better suited to routine airflow measurements in mine roadways and ventilation ducts. This paper concludes a study sponsored by the Atomic Energy Control Board of Canada, that was introduced at the 5th U.S. Symposium. The study investigated the suitability of currently available electronic anemometers as replacements for the traditional mechanical analog devices while maintaining standard methods such as the continuous traverse. Six electronic instruments were subjected to extensive tests under controlled conditions both in a wind-tunnel and in the field at an underground mine. The evaluation concluded that ergonomics and design were major considerations in unit preference as most of the instruments had very similar performance characteristics. Specific findings were: a) In the wind-tunnel the vane anemometers, especially the "micro" vanes, were more susceptible to misalignment or yaw effects but these were not noticeable in the field; b) Both the vortex and hot-wire anemometers were suitable for continuous traverses of mine roadways; c) Traversing ventilation ducts was more practical than a Pitot-tube multi-point assessments or discharge measurements; d) Yaw is a major concern in duct measurements; e) The continuous traversing method for roadways overestimates the average air velocity; f) Hot-wire anemometers can require significant air density corrections; and g) Hot-wire anemometers are better suited than rotating vanes to mine roadways of less than 1 m/s average air velocity. Based on research detailed in this paper, the ventilation engineer should be able to match the mine's requirements with the presented instrument performance characteristics, thereby optimizing the purchase of a new anemometer and the efficiency with which air velocities are measured.

Jan 1, 1993

By William D. Mayercheck

The introduction of continuous mining machines in the late 1940's prompted the mining industry to reassess shuttle car batch-type haulage. Between place changes, the continuous miner could cut and load coal on a nearly continuous basis, but after loading a shuttle car, the high-capacity machine had to wait until the second shuttle car came inby and spotted itself under the miner tail boom. Thus, the wait-for-shuttle-car delay periods became the new bottleneck for increased coal production from the mine section. Recent studies have shown that nearly 25 pct of the continuous miner cycle time is consumed by delays in the haulage system, usually waiting for shuttle cars. Computer simulations of a face operation indicate that up to a 45 pct increase in coal production may be realized through the use of a continuous haulage system, assuming of course that the outby haulage system can handle this increased capacity. Coincidently, there are recent claims by some mines using continuous face haulage of a production increase of 45 pct compared with shuttle car haulage. These documented production records, computer simulations, and common sense indicate the potential of continuous face haulage in underground coal. The late 1960's and early 1970's saw several mining machinery manufacturers market mobile bridge carrier and piggyback bridge conveyor continuous haulage systems for use in underground coal mines. These systems have shown limited potential in some mines and outstanding success in others. It appears that no one system can be universally applicable to all underground mining conditions; thus, the Bureau of Mines has conducted extensive research over the last few years to investigate different types of continuous haulage systems for use in high and low coal seams that will advance the state of the art.

Jan 1, 1977

By N. Edmonson

During the last 30 years, a dramatic increase in the supply of byproduct sulfur substantially reduced the share of the market held by Frasch-mined (non-by-product) sulfur in North America. Even though Canadian sulfur production is not discretionary, the geographic remoteness from the large US markets and the high transportation costs associated with delivering sulfur to those markets has meant that Canadian producers act like discretionary producers in many important ways. They have effectively replaced the US Frasch producers as the cost-marginal sulfur source to large US markets. Implications of this change in market structure include more volatile sulfur prices and longer sulfur price recessions.

Jan 1, 1997

By Ron Robinson, Trevor Harrison

The planning, installation and commissioning of the first scheme of controlled recirculation of air flow in a section of coal mine in Great Britain is described, together with the proposals for a second installation. The work updates a previous paper (Robinson and Harrison, l986) on the subject. The special problems of ventilating the increasingly distant faces of the undersea mines in the North East Area of the British Coal Corporation are discussed and the alternative solutions stated. The advantages of using a system of controlled recirculation of air are proposed together with the safety features considered necessary. Design and installation details of the recirculation fans and a new booster fan are described.

Jan 1, 1987

By Natarajan K. A.

During sulphide ore grinding, electrochemical interactions between grinding medium and the minerals play a significant role in bringing out enhanced ball wear on the one hand and alter the surface property of the ground minerals on the other. The role of the flotation reagents added simultaneously during grinding with respect to ball wear as well as flotation is yet to be established. Electrochemical measurements such as rest potential, combination potential and galvanic current between sulphide mineral and ball material couples have been carried out in the presence and absence of flotation reagents to understand the nature of electrochemical interactions between ball material and sulphide mineral. Electrochemical mechanisms and models have been proposed to explain the role played by the flotation reagents during different binary, ternary and quaternary interactions with respect to ball wear during grinding.

Jan 1, 1992

By Bruce Kennedy, Dan Nilsson

Mining means drilling and blasting in order to break down the rock, loading and transport, and often also crushing the ore down to a suitable size. These operations can be done in open pits or in underground mines, and also, to a lesser extent, in marine mining. The same operations are also used in various types of construction, i.e., for roads, water power stations, etc. Before beginning a detailed economic analysis of the factors which enter into deciding whether to mine by open-pit or underground mining, and at what point a change should be made from open-pit to underground mining, or vice versa, it is of interest to consider some general factors.

Jan 1, 1982

By G. Troly, M. Esterle, B. Pelletier, W. Reibell

In New Caledonia, ultramafic formations occur on 7,000 square kilometers. Weathering of peridotites leads to profiles of alteration and nickel concentrations. Complete profiles are composed of two main groups of horizons: 1. Limonitic, mainly composed of iron hydroxides 2. Saprolitic, partly composed of magnesium and iron silicates Shape and mineralogical composition of saprolitic horizons are chiefly affected by the nature of the bedrock: types of peridotite and their degrees of serpentinization. On the other hand, morphology (plateau, terraces, slopes, piedmont) is an important factor. Ore-bodies are inside saprolites; their outlines are determined by the grade of nickel and tonnage economically mineable. Information about geology, morphology, geochemistry, and mineralogy are given in this paper.

Jan 1, 1979

By Eudes Prado Lopes

The Mineral Resource Exploration Company - CPRM - a part-private, part-government concern jurisdictioned to the Ministry of Mines and Energy of Brazil, was founded in 1969 for the purpose of promoting the exploration of mineral and hydric resources throughout Brazil. The political-administrative framework within which it was conceived and created considering that an economic and financial balance to be maintained in all its fields of activity, CPRM set out right from the start to organize itself to perform -three basic lines of action, which can be summarized as follows: As a Service Company, to carry out those services requested by government agencies and by the private sector through of service contracts; As a Mining Company under the Brazilian Mining Code, aiming at supplementing private initiative, not beyond the field of mineral exploration;

Jan 1, 1975

By John G. Reid

Geologists, employed by the Australian Company, Metals Exploration Limited, discovered nickel laterite enrichment at Greenvale in 1967. A joint venture was arranged with the Freeport Minerals Company who had gained early experience with nickel laterite ores when building and operating the Nicaro and Moa Bay Treatment Plants in Cuba. A 5 tonne/day Pilot Plant at the Freeport research facilities at Belle Chasse, Louisiana, verified the amenability of the ore to treatment by the reduction and ammonia-ammonium carbonate leaching process used at Nicaro. A 5 800 tonne/day Treatment Plant was constructed on the coast at Yabulu, North Queensland. This paper describes the ore body, the mining operation and the stages of treatment required to produce nickel oxide products and a mixed nickel/cobalt sulphide product at Yabulu.

Jan 1, 1979

This chapter contains the edited transcript of the "Gold Heap Leach Information Exchange" session that was held at the 1990 SME/AIME Annual Meeting in Salt Lake City, Utah. The exchange occurred on the afternoon of February 27, 1990. The session was intended to act as a forum for discussing some of the more prominent operating problems associated with heap leaching precious metals. The information exchange was very successful. The exchange consisted of several panelists introducing and discussing different topics, follow by a comment and question period. This transcript contains the panelists' presentations as well as comments and questions from the floor and the panel. Extraneous comments and remarks have been edited out. Some wording has been changed for clarity, but the transcript is basically an accurate account of what was said. At the end of the transcript are two papers submitted as part of the panel discussion

Jan 1, 1990

By Manfred Jaeger, Klaus Ertmer, Walter Dietrich, Jochen Greinacher, Wilhelm J. Kogelmann

In Europe, novel low-cost excavator-mounted Multi Tool Miner (MTM) systems, consisting of cutter head, hammer, bucket and drill attachments permit one unit to perform multiple tasks replacing several purpose-built machines. At the Weser Tunnel in Germany, cross-passages between the twin tubes were excavated in frozen ground with a remote-controlled mini-excavator equipped with a quick-change cutter head, ripper tooth and bucket. In Switzerland at the N2 interstate near Basel, W. Dietrich AG enlarged a 2-lane tunnel to three lanes with a cutter head mounted on a special excavator. Blasting and heavy hammers were not permitted due to the closeness of the “live” twin tube. At the N20 Zurich bypass, the Joint Venture of Jaeger, Frutingerand AHB excavates highway tunnels, some with extremely large cross sections, conventionally. A cutter head mounted on an excavator removes the rock shattered by blasting precisely to the pay line, thus preserving the rock’s self-supporting capacity preventing subsidence and damages to water resources and buildings on the surface under low overburden.

Jan 1, 2003

By Hingant Pierre

The Hurtières Tunnel was built in 1995 with drill and blast method, in metamorphic schist. It is located between Lyon and Torino on the A 43 motorway in the French Alps. During the construction, a geological hazard was encountered, which caused a massive ground collapse. The tunnel was filled up with 3,000 m3of glacial materials. Geological investigations realized after the accident showed that a narrow glacial valley was present at this location the water table was 40 m above the tunnel level. The paper will describe the collapse and the remedial methods which were implemented to proceed through the failure area. These included drainage works,2,000 m3 grouting and 6,200 ml jet grouting columns.

Jan 1, 1999

By M. D. Johnson

The San Andres mine, located in the western mountain region of Honduras, Central America, contains epithermal gold mineralization as disseminations, in quartz-chalcedonic veins and stockworks. Host rocks include a thick sequence of Cretaceous to Tertiary conglomerates, sandstones, rhyodacite tuffs and andesites. Mineralization is controlled by northwest and northeast striking, normal faults and fractures which dip steeply east and west. Currently, 500 STPD of 1. 93 Grams/MT gold ore is being open-pit mined from the conglomerate and andesite. The mine is at the west end of a mineralized zone that can be traced over an area of approximately 1.5 square kilometers.

Jan 1, 1993