Search Documents

Stillwater Mining Company has an extensive history with tunnel boring machines (TBM) at the Stillwater and East Boulder underground PGM mines in Montana. The first use of a TBM was a 4 m (13 ft) diameter main beam unit at the Stillwater mine starting in 1988, where 6.4 km (4 mi) of tunnels were driven parallel to the J-M Reef orebody on four different levels. TBM?s were central to the development of the East Boulder Mine as two 4.6 m (15 ft) TBM?s drove two 5,639 m (18,500 ft) parallel tunnels to access the J-M Reef; one of these units is still in service driving a 2,591 m (8,500 ft) access West of the East Boulder mine for the Graham Creek project. For the Blitz Project, a 5.5 m (18 ft) diameter main beam unit will be utilized to drive a 6,858 m (22,500 ft) ventilation and rail haulage level East of the Stillwater mine. TBM?s have been preferred method for developing new mines and sections of the J-M reef as the geometry and geology of the Stillwater Complex allow for faster development compared to conventional methods.

Jan 1, 2012

By Myles G. Hyams

A mining project is proposed for the state of Pahang, Malaysia. The proposal involves the mining of a sulphidic ore body and initial processing to form a sulphide concentrate which will be transported to a roaster/acid plant for the production of sulphuric acid. An outline is presented on the potential environmental impacts of the project which have been assessed by superimposing project infrastructure and processes on to the physical, biological and social environment during the early design and planning stage of the project. The potential impacts eliminated by engineering design and the techniques employed are presented. However, there are a number of potential impacts that require careful consideration and planning for long term management. These include surface water drainage, waste rock leachate, tailings disposal and the social environment. Environmental management designed to minimise or alleviate these impacts as a result of project implementation concludes the paper.

Jan 1, 1991

By S. S. Huyett

The opportunity to cooperate with the Mining Department of the Pennsylvania State University in their Student-Trainee Program is accepted by The New Jersey Zinc Company who believes that the participation in this type of a program will lead to a larger supply of high calibre engineers in mining. Trainees compete with other employees to earn the cost of their education while gaining practical experience in the mining industry. The practical experience is arranged to complement the technical education through a variety of work assignments. Job opportunities for the trainee are related to the work requirements of the Company and to the performance of the trainee. Management must consider and deal with a good many problems uncommon with regular, full 'time employees. For a number of reasons this program is recommended to other companies as a means to encourage outstanding young men who are interested in a career in the mineral industry to obtain a professiona1 education.

Jan 1, 1963

By E. R. Pantos

US coal production increased 3% to a record 832 Mt (917 million st) in 1987, according to preliminary Energy Information Administration (EIA) data. Most of the increase was due to the unusually warm summer and the increased coal-fired electricity demand for air conditioning. Drought conditions in the Northwest lowered hydroelectric generation, contributing to the higher use of coal by electric utilities. However, excess production capacity and increased competition from natural gas added further downward pressure on delivered coal prices, continuing the declining price trend of the last several years. Coal production by region Appalachian coal production reached 402 Mt (443 million st) in 1987. This is about 3% more than in 1986 and just short of its 1984 peak. Virginia produced 7% more than its 1986 level, due to increased coal-based electricity demand. Smaller percentage increases were attained in eastern Kentucky, Pennsylvania, and West Virginia. Ohio and Alabama were the only major coal-producing states in Appalachia that produced less coal in 1987 than in the previous year. In the Interior region, 1987 coal production reached a record 182 Mt (201 million st), about 2% above 1986. Illinois is the largest coal-producing state in that region. Production there fell about 3.7%, primarily because of lowered demand at electric utility plants in Alabama and Tennessee. However, this was more than offset by production increases in western Kentucky, Texas, and Indiana. After falling slightly in 1986, coal production in the West resumed its upward trend to a record 248 Mt (273 million st). Wyoming is that region's dominant coal producer. It mined 7% more coal than in 1986. Wyoming's increase offset the 11% decline in New Mexico production and smaller declines in other Western states. Coal consumption and prices Domestic coal consumption reached a record 759 Mt (837 million st) in 1987. Most of the increase resulted from the unusually warm summer that led to higher than normal peak demands for electricity in the third quarter. Electric utility coal consumption was also boosted by the below-normal hydroelectric generation that resulted from low water levels in the Northwest. These factors more than offset the effects of increased nuclear power generation and competition from natural gas. As a result, coal provided 56.9% of electric utility generation in 1987, compared with 55.7% in 1986. Electric utilities consumed a record 651 Mt (718 million st) of coal. While electric utility coal consumption increased, the average cost of coal to utilities was down, from $1.58 per million Btu in 1986 to $1.52 in 1987. The average price of coal delivered to utilities in 1987 was $35.09/t ($31.84 per st), the lowest since 1981. Coal prices were held down by a glut of coal supplies and by a decline in the average price of natural gas to electric utilities. Coal consumption at coke plants in 1987 was 2.6% above the 1986's 32.5 Mt (36 million st). This increase reflects steel's recent resurgence. Coking coal demand, though, was reduced by the increased use of continuous casting and electric furnace technologies. The average price of coal delivered to coke plants fell from $56.02 to $51.35/t ($50.83 to $46.59 per st). Coal consumption in the industries other than coke plants amounted to 68.2 Mt (75.2 million st) in 1987, slightly less than in 1986. Coal lost part of its market share to natural gas, which was priced favorably relative to coal. The average price of coal delivered to manufacturing plants was at its lowest level of the current decade. It fell from $39.50/t in 1986 to $37.27/t ($35.84 to $33.81 per st). Residential and commercial coal consumption fell to 6.2 Mt (6.9 million st) that is 9.8% below 1986 and the lowest since 1980. This decline is also attributed to the relatively low price of natural gas in 1987. Coal stocks Coal consumers held 169 Mt (186 million st) of coal stocks at the end of 1987, 5.9% above the 1986 year-end level. Most of this increase was due to stockpiling by electric utilities in anticipation of a possible strike by the United Mine Workers of America early in 1988. Stocks at electric utilities increased to an estimated 154 Mt (171 million st) at the end of 1987, 5.6% higher than the previous year. This was much lower than 1984's stock buildup. Coke plants increased their coal stocks by 30% in 1987 to 3.5 Mt (3.9 million st), rebounding from the unusually low inventories of 1985 and 1986. Other industries increased their stocks slightly in 1987. Coal producers and distributors ended 1987 with 25 Mt (28 million

Jan 5, 1988

By A. L. Stomberg

Federal and State surface coal mining regulations require special handling of prime soil materials which result in additional costs, and no actual benefit when prime and non-prime soils are similar. The Coteau Properties Company proposes to mix both prime and non-prime topsoil and subsoils at the Freedom Mine in Mercer County, North Dakota, based on an analysis of soil physical and chemical characteristics which show these materials to be comparable.

Jan 1, 1985

By T. M. Biddle

If an accident occurs at a mine, the mining company, its parent and affiliates, and its supervisory employees may face substantial -- and sometimes unexpected -- liabilities and costs. This presentation surveys the likely sources for post-accident exposure, including wrongful death and personal injury claims, mine closure/operational disruptions, and government civil and criminal actions against the company and its employees.

Jan 1, 1986

By Ronald H. Mullennex

The growing need for development of thinner, more erratic, or less easily- mined coals in the Appalachian region requires more detailed analysis of conditions and factors controlling or influencing deposition of these seams. The value of depositional modelling in evaluation of such coals has been demonstrated in many recent studies and publications. Such modelling may be applied to allow prediction of factors varying from regional coal occurrence trends to very local areas of seam discontinuities, but requires thorough utilization of all available types of data. Mapping of general depositional energies, as derived from basic geophysical and driller's logs, can be applied to specific prediction of coal occurrence, and projection of particular facies as representative of unique depositional features or conditions often proves more applicable to coal character delineation than does mapping of the coal itself. Depositional modelling and trend projection may also serve as a guideline in reserve classification and confidence-levels in reserve estimations.

Jan 1, 1981

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

"A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob. INTRODUCTION During a series of stakeholder meetings, a near unanimous concern was expressed related to maintenance of effective ventilation airflow on longwall faces. There was a strong interest expressed regarding the impacts of face length and caving characteristics on the ability to maintain adequate face airflow levels. This study seeks to understand and improve a mine operator’s ability to monitor and control ventilation and methane concentrations across the longwall face by assessing airflow variations in terms of roof caving characteristics and face length. National Institute for Occupational Safety and Health (NIOSH) researchers seek to identify flow paths of ventilation airflow on longwall panels with variations in roof caving characteristics and longwall face lengths. The project research aims to develop an understanding of the role of gas dynamics in variable broken rock, interactions with ventilation airflow and methane concentrations across the longwall face area. The research also addresses continuous ventilation monitoring along the shield line to provide early detection of gas exchanges between face and gob, and thus improve a mine operator’s ability to monitor and control ventilation and methane concentrations around the face. In the context of this paper, the longwall gob refers to the pillared area behind the shields. This work reports on results from one project task to conduct field based research using a tracer gas to describe face air and gob area gas movement in a bleederless longwall ventilation system that incorporated a back return."

Jan 1, 2017

By Z. T. Bieniawski

The efficient and safe design of room-and-pillar coal mines still remains as one of the pressing problems facing the mining industry in the United States. Although much research has been directed to stability of mine roofs and coal pillars, no generally-accepted design method has been formulated. This paper presents a concise procedure for an improved design of room-and-pillar coal mines. Developed as a result of a three-year research effort, the methodology includes essentially three aspects: (i) determination of stable roof spans; (ii) determination of the strength of coal pillars; and (iii) determination of safety factors for room-and pillar coal mining in the United States. It is shown that the presented approach will lead to a greater recovery of coal by a more economical, yet safe, mining operation. Design charts and tables are presented and a step-by-step design procedure for practical mining engineers is explained. Several examples are included demonstrating the use of the proposed design procedure for room-and-pillar coal mines.

Jan 1, 1983

By M. P. Saunders

A comprehensive, site specific water management plan is of primary importance to the successful implementation, operation and decommissioning of any mining project. Formulation of a plan requires an orderly planning process consisting of identifying problems, establishing planning criteria based on the guidelines and requirements of regulatory agencies, and an iterative procedure of identifying, investigating, and evaluating plan elements and alternative plans. A typical uranium surface mine operation consists of a mine pit or pits, spoil pile areas, crusher, processing plant, and tailings disposal area. A water control plan addresses the problems of diversion of natural runoff from undisturbed areas around the mine; and diversion, collection, and treatment of runoff from within the mine area. A water control plan is required to determine the location and size of appropriate control and detention structures; their cost; and the schedule for permit activity, design, and construction. The plan must be formulated to meet the requirements of both the State and Federal regulatory agencies.

Jan 1, 1981

By Anthony G. Fonseca, W. W. Wen

About 45-50% of the coal mined in the U.S. passes through coal preparation plants; east of the Mississippi River this number increases to about 75-80%. Although the cost for coal preparation is worthwhile to some, the coal industry faces the challenges of continuing downward pressure on the price of coal and the impact of new environmental regulations. Coal preparation, as commercially practiced today, is an effective process achieving 75-803 ash reduction, 15-8m trace element reduction, and 85-90% Btu recovery; it is less effective for pyrite reduction (35-70%), and on-line operating time (40-60%), and suffers from obsolete control systems. Methods will be discussed for reducing costs of coal preparation and improving the performance of coal preparation plants. Comments are included on equipment selection, especially for -28 mesh coal, and prep plant operation and control practices. Btu recovery, ash and pyrite reduction, fines processing including dewatering and slurry fuel use options are emphasized. Trace element removal and expert control systems for maximization of prep plant operation also will be highlighted.

Jan 1, 1995

By R. Srikanth

Dust control in high production longwalls is a major problem requiring, among other things, careful attention to the design of operating practices, and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in U.S. longwalls; yet under certain conditions, 31 percent of the shearer operator's dust exposure can be due to support movement. Several methods have been developed for the control of shield-generated dust. Yet the need for better methods is apparent. In this paper, the amount of airborne respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. A total of ten experiments were conducted in five longwall faces in four different mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne respirable dust concentration immediately downwind of the shield moved, varied between 0.12 and 1. 75 mg/m3 in the five longwall faces. The mass of airborne respirable dust generated by shield movement was found to vary between 39 and 386 milligrams per shield move. The results from this study reveal that control of dust from longwall shields requires a combination of approaches involving alternative operating practices, reducing shield dust generation rate, increasing face air flow, and decreasing personnel exposure.

Jan 1, 1994

By V. N. Sukhov

This set was developed to use the mathematical methods and computers in the data analysis and accumulation of the large amount of geological data to solve the typical geological problems at the deposit exploring stage as well as for planning and managing in the open cast deposit mining. That is to say, the set of tasks ensures the geological data base at the stage of the deposit exploring and also its further use and. updating at the exploration stage. The following main elements may be ear-marked in the complex: (1) geological data base (GDB), (2) the data input system, (3) GDB maintainance, (4) "Geologist" geological application package (GAP). Let us consider now each element purpose. 1) GDB logical structure is determined through five hierarchical substructures with a common root segment.

Jan 1, 1986

By A. F. Peterson

There is no single mining problem at Benson that does not exist at some other mine. There are four, however, that require special attention primarily because they occur together and have an influence on each other. These are the nature of the mineral occurrence, the shape of the ore body, the operating schedule, and the climate. It is the purpose of this paper to describe mining practices in relation to these four factors. Iron ore was first noticed in the Star Lake area early in the nineteenth century. Prior to Jones and Laughlin leasing the facilities built by the Defence Plant Corporation, several companies tried to mine the ore body but gave it up as uneconomical. While there is a little high grade (40%) magnetite, most of the ore contains 20 to 25% iron and not enough was known prior to World War II to design a profitable operation. By 1943, and certainly in the years that followed, technological developments in ore dressing and mining not only put the magnetite into the category of a commercial ore, but made possible the concentration of the non-magnetic iron mineral, martite. This last development nearly doubled the ore reserve. Jones and Laughlin bought the DPC holdings in 1946 and has since expanded the plant to its present capacity of 4,400 gross tons of concentrates daily or 1,600,000 gross tons per year. Magnetite makes up 62% of this production at the present time, but it will be necessary before long to bring martite production up to about 45% of the total because of the ratio of the two ores in the reserves. To keep the plant supplied, 14,000 to 15,000 tons must be mined and crushed daily, with a ratio of concentration that varies from 2.8 to 3.4. The ore body is 12,000 feet long and varies in width from 600 to 1,500 feet. The waste rock is, for the most part, a granite gneiss, and the overburden, of which little is left, is a glacial drift sand. For the entire reserve, there is a half ton of rock for every ton of concentrate, but the stripping ratio is more than one to one at present because of the existence of more rock in the upper mining levels in relation to the ore. The dirt stripping or development work that cannot be handled by company facilities is contracted to an outside firm. The need for this diminishes every year and will soon disappear. The deposit looks like a "J" in plan, with the long leg running approximately north and south and the short leg to the west. The primary crushing plant, consisting of a 54" gyratory followed by two 18" gyratories and a 1,500 foot conveyor belt to the fine crushers, is located on the third level where the long and short leg of the mine meet. The widest part of the pit lies just the north of the crusher. The mine is operated on a lease that expires in 199l0 There are two fee owners, the Benson Iron Company, which owns slightly overhlf of the reserves, and the Newton Falls Paper Company, which owns the balance. There is no appreciable difference in the mining on the two fees, so the ore is removed in strict proportion to calculated reserves during each year. Basic mining equipment consists of eight 45 yard electric shovels, a fleet of twenty-five 22 ton end dump trucks, eleven churn drills for nine inch blast holes, and two small percussion drills for four to five inch holes, There are the normal auxiliary items, such as dozers, graders, wagon drills, and two drop-ball cranes. Power is purchased and, where practical, is used at 4100 volts. Pit drainage pumps can handle a maximum of 11,500 GPM from the several sumps, but water is a problem only during the spring or when a sudden thaw follows a heavy snowfall.

Jan 1, 1958

By J. A. Herbst

Introduction The ability to evaluate the improvement resulting from the implementation of an automatic control system is essential to the Justification of its cost. This evaluation may occur after anew control system has been commissioned. In other cases an existing plant which is operated manually may be automated only In part in order to determine In ether the met of it should be. Finally. in some instances dynamic isolation my be used prior to installation of the control system to determine the strategy to be used or to evaluate the improvements In process performance expected from automatic control. This paper describes the development of a methodology for making these evaluations. In order to obtain an accurate assessment of Improvements In a short time, statistical methods can be employed. Mineral processing plant, are subjected to many types of both random and deterministic disturbances of various duration. The statistical method, available for process control at analysis are designed to counter the obscuring effects that random disturbances have on such as evaluation. The basis for evaluation and comparison is some freely chosen measures of process performance termed the performance index or objective function. The experimental data used to calculate the performance index should, if possible, be collected by alternately running a circuit Or plant with the two or more type, or control being tested ("serial testing”) or more preferably, by running two circuits with the two type, of control side by side ("parallel testing") . The performance index is a random variable so that when comparing two types of control, statistical hypothesis testing must be used. By testing s hypothesis statistically one accept, or reject, a (null) hypothesis [ ] concerning the mean or variance of one or more performance indices. For example, a hypothesis Ho might be that the mean of a performance index with stabilizing control is larger than with manual control. Defining a Performance Index The performance index, denoted by [ ] , is a measure by which alternative strategies or situations my be cam peered on either s technical or an economic basis (see Table 1). Technical measures are concerned with the effects of control on process variables or outputs or on the deviations of controlled variable, from their setpoints. For commotion circuit, important technical measures of performance are throughput, product fineness and the consumption of liners, media and electrical energy. For flotation circuits important technical .satires are recovery, grade and reagent consumption. Economic measure such a, cost and profit n usually determined from a combination of technical measures and are usually the final factor upon which a decision may be made, although a control system my achieve higher values of technical measure , the control effort expended my be of such magnitude that the economic measures, such as cost, are poor. Running Comparisons Comparison, between automatic and manual control are normally done with data obtained before and after control system Installation, unless ore characteristics remain the same during the period of data collection the results will be biased. By running the test circuit with the control system alternately turned on and curled off until all possible ore type, have been run through the circuit, unbiased result, can be obtained. This mode of testing is termed “serial testing.” An alternative and potentially more powerful and quicker made of testing is "parallel testing" in which two circuits, one with the type of control being tested and one without, arm run aide by side. In this type of testing both circuits process the same ore so that valid results occur sooner than with aerial testing. The data may be averaged before testing or the differences in the performance indices may first be calculated before averaging. However, the two circuits must be nearly identical in their mechanical characteristics otherwise differences other than the degree of control will bias the results. It mechanical differences exist than it my be necessary to adjust one or the circuits prior to testing. Sometimes it is possible to correct far mechanical differences based on Inherent efficiency calculations made with a model. Hypothesis Testing Once the data is collected, hypothesis fencing can be carried out to determine if the automatic control system has resulted in a statistically significant improvement. One can construct a histogram of the distribution or performance indices with am without control such as Figure 1, or the

Jan 1, 1991

By J. G. Jenkins

Magma Copper Co.'s San Manuel solvent extraction/electrowinning (SX-EW) facility has operated since May 1986. The original facility had a design capacity of 22.6 kt/a (25,000 stpy) of electrowon copper cathode produced by processing pregnant leach solution from an open pit-heap leach operation. In 1988, the plant was expanded to 45.3 kt/ a (50,000 stpy) to incorporate processing in-situ leach solutions. This pager focuses primarily on the heap leaching area with regard to exploration, testing, feasibility, permitting, design and construction, and operating practices. Research using surfactant leaching aids to enhance copper recovery is also discussed.

Jan 1, 1995

By J. Brad Dalton, Sam Vance, Trude V. V. King, Roger N. Clark, Raymond F. Kokaly, Gregg A. Swayze, Dana J. Bove

Visible-wavelength and near-infrared multispectral image cubes for the Animas River Watershed from Hermosa, Colorado to the headwaters at Animas Forks, Colorado were acquired on June 18, 1996 using the Jet Propulsion Laboratory's AVIRIS (Airborne Visible and InfraRed Imaging Spectrometer) instrument (Green et al., 1998). These image cubes have been analyzed using the USGS Tetracorder V3.4 implementation (Clark et al., 1995), an expert system which utilizes a database of more than 300 laboratory spectra of endmember minerals and mineral mixtures to generate maps of mineralogy, vegetation coverage, and other material distributions. Major iron-bearing, clay, carbonate, and other minerals were identified along with several minerals associated with acid-generating hydrothermal systems including pyrite, jarosite, alunite and goethite. Additionally, distributions of alkaline minerals such as calcite and chlorite indicate a relation between acid- buffering assemblages and stream geochemistry within the watershed.

Jan 1, 2000

By James S. Scott

Effluents discharged from gold mills, and more recently from heap leaching operations, pose significant hazards to the environment if not properly managed prior to discharge. This paper describes the nature of wastewaters which must be treated, the treatment processes being applied in Canada and the capabilities of these methods in removing cyanide and metals. As a result of past practice the most common method of reducing cyanide in gold mill effluents remains that of natural degradation in tailings ponds. This method has proven capable of producing high quality effluents where large ponds and sufficiently long water retention times can be provided, but at many mines this has not been the case. Since 1981, as a result of these limitations there has been a strong move in Canada to chemically-based effluent treatment plants, particularly as additional processes became available. Canadian gold mills have become leaders in the use of chemical processes to remove cyanide, in terms of the variety of such processes in operation (five in total), the number of plant installations and the number of processes developed in this country. The hydrogen peroxide and Inco SO2-air processes, in that order, are being applied most widely. Alkaline chlorination, the initial process to be used fairly extensively has been almost totally replaced by the two methods mentioned above. Since a number of effective methods are now available for the treatment of gold mill effluents, the selection of a process for application at a specific mill requires careful consideration of:

Jan 1, 1987

By Donald L. Freed

Design, development, factory test, and in-mine evaluation plans are presented for an Automated Extraction System (AES) that has been designed to fill needs which are present in the Mining Industry. The philosophy of design and proposed operation of the machine, as well as the relationships between these factors, and final machine configuration are reviewed. The AES is designed to overcome production problems resulting from the regulation of roof control, clean-up, ventilation, dust suppression, and operator protection required by the Federal Coal Mine Health and Safety Act of 1969. The design permits more continuous operation and greatly improves operator safety. The machine is a full-face drum-type continuous miner which includes self-advancing, continuous temporary roof support. Onboard self-advancing face ventilation, dust suppression, and air scrubbing equipment are also included in the design. A further improvement over existing equipment is the incorporation of an automatic programmed cutting cycle control system. All mining functions including movements of the roof support system are handled by this automatic system.

Jan 1, 1977

By William C. Cox, Ronald E. Heuer, Jean-Michel Loignon

The Gatineau shaft described in this paper was an excavation of about 38 m diameter and 21 m depth constructed in Gatineau, Quebec, across the Ottawa River just north of Ottawa, Ontario. A large sewage lift pumping station-was to be constructed in this excavation. Subcontractor for the shaft excavation and initial support was Beaver Underground Structures Ltd., of Dorval, Quebec. Mr. William C. Cox of Beaver conceived the idea for the support system used in this excavation, and was responsible for the construction activities. Initial analysis and design concepts for the lining system were developed by Mr. Ronald E. Heuer. Detailed lining design and construction monitoring were the responsibility of Mr. Jean-Michel Loignon. Geologic conditions indicated by two borings within the shaft area are illustrated in Fig. 1. The shaft excavation would be in the sensitive Leda silty clay. The clay is of stiff to very stiff consistency, with an insitu vane shear strength averaging about 115 KPa (2400 psf) and a reported low value of about 87 KPa (1820 psf). Low strength values were from the middle of the clay layer, with higher strengths at the top and bottom. Average shear strength at the level of the base of the excavation was about 137 KPa (2860 psf). Remolded vane shear strength averaged about 20 KPa (420 psf), with a reported low of 13 KPa (270 psf). Based upon average strength values, the clay sensitivity is 5.8. The clay has an average water content of 53% (range 43 to 66%), which is near its liquid limit (average 56%). The clay unit weight is about 1760 kg/m3 (110 pcf). Underlying the shaft site at shallow depth is limestone bedrock within which the piezometric head is approximately equal to the original ground surface elevation. For shaft support, a -cast-in-place concrete wafer system was considered, but was discarded because of time restrictions imposed by concrete placement and curing. The support system selected utilized liner plate with light steel walers closely spaced. The light rib

Jan 1, 1983