Search Documents

By Wei Luo, Yuanbo Zhang, Zhixiong You, Zijian Su, Guanghui Li, Tao Jiang

"In this study, the appropriate sintering process parameters for low-grade ferromanganese ores were investigated. The results showed that, under the condition of natural basicity (R=0.03), the optimal parameters were obtained as follows: moisture of mixture 9 .1 %, coke powder 9 .9% and sintering negative pressure 7 KPa. And the corresponding yield, ISO tumbling index and utilization coefficient reached at 80.18%, 61.27% and 1.515t·m-2·h-1, respectively. Under the optimal parameters, the emission of harmful gases, such as S02 and NOx, were reduced evidently with 30% of coke powder replaced by biomass charcoal. Moreover, it was found that the basicity had obvious effects on the quality of the sinters when it changed between 0.03 and 2.4. The ISO tumbling index gradually decreased from 61.27% to 55.47% with the basicity increasing from 0.03 to 1.2, then, it began to increase after the basicity further increased to 2.4.IntroductionManganese is mainly consumed by steel and battery industries, particularly in the steel plants and ferroalloy units. The consumption of metal manganese in the ferroalloy industry accounts for 85%-90% of the total Mn [1-2]. Therefore, ensuring sufficient manganese alloys is essential to meet the rapid development of steel industry. Recently, rich-manganese slag containing high grade Mn (>40%), low Fe (1%) and P (<0.03%) is considered as superior raw materials for manganese alloys. While the sinters made from manganese ores are major raw materials for producing rich-manganese slag with the increasing exhaustion of natural rich manganese lump ores [3-5]."

Jan 1, 2013

By Riqing Ye

Laser Engineered Net-shaping (LENS TM) is an emerging manufacturing technique that ensures significant reduction of process time between initial design and final components. The fabrication of fully dense parts with appropriate properties using LENS TM process requires an in-depth understanding of the entire thermal behavior of process. In this paper, the thermal behavior during LENSTM processing of 316 stainless steel was studied both numerically and experimentally. Temperature distribution and gradient in the fabricated 316 stainless steel part were obtained by Finite Element Method (FEM) simulation. The numerical results are in good agreement with the experimental observations. The numerical method may be used to optirnize process parameters and predict the thermal response of LENSTM fabricated components. Key words: Laser Engineered Net-shaping, Thermal Behavior, Finite Element Analysis

Jan 1, 2003

By Robert M. Leary

The Kennecott Utah Copper smelter operates two Outokumpu flash furnaces: a smelting furnace for production of high-grade matte and a converting furnace for production of blister copper. Flash furnaces typically possess several characteristic features that must be considered in process control development such as long lag times associated with settler volume, non-linear input and output responses, large process gains, and unmeasured disturbances. Additionally, the Kennecott smelter possesses certain unique characteristics which must be considered such as single mine concentrate source, limited concentrate blending capacity, and feed preparation facilities that inevitably cause significant lags between furnace control parameters and manipulated set points. In order to improve furnace control and on-line time, a process control system was developed to address these issues. The feed forward control module provides predictive control and operates in response to furnace feed input changes. The feed back control module provides responsive control and is based on furnace output deviations. To provide regular feed back information to the control room supervisors, new sampling methods were developed which provide the operators with molten metal and bulk material samples at regular intervals to provide information for control. The control system was implemented on the Flash Converting Furnace in May 1999 and on the Flash Smelting Furnace in August 1999.

Jan 1, 2000

By C. P. Broadbent

The process metallurgy of many nickel laterite smelting operations is controlled largely by the physical chemistry of the slag system. Consequently, accurate phase diagram information and physicochemical property data are essential to interpret and predict the behaviour and optimisation of the overall process. The system (SiO2 - MgO - FeO) first described by Bowen et al. between 1914 and 1935 and the system (SiO2 - MgO - FeO - Fe2O3) determined by Muan and Osborne in 1956 are of particular relevance to the study of nickel laterite smelting slags as these systems form a reasonable approximation of many industrial slags. This paper will review the literature for these (and other relevant) phase systems. In addition data available from the ternary and (quasi)ternary phase diagrams will be compared with data obtained from industrial slags. The physico-chemical properties under consideration will include; melting and crystallisation behaviour (solidus and liquidus temperatures), viscosity - temperature relationships, heat flux considerations, electrical conductivity, surface and interfacial tension.

Jan 1, 1993

By J. E. Wey

Extraction of cobalt from cobalt sulfide and cobaltite flotation concentrate from the Blackbird Mine, Idaho, was investigated using an adapted strain of Thiobacillus ferrooxidans. Cobalt extractions as high as 100% were realized in the inoculated experiments, whereas only 4% extraction was obtained in the sterile run. The influence of pulp density on the rate and extent of cobalt extraction was also determined. It was found that the extraction of cobalt followed predominantly the indirect mode of bacterial activity. In this process, ferric iron oxidizes cobaltite to cobalt sulfate and ferric arsenate while being reduced to its ferrous state; the bacteria continuously re-oxidize ferrous to ferric iron. Electrochemical measurements using cyclic voltammetry suggested that cobaltite oxidation involved a number of intermediate reactions.

Jan 1, 1993

By Junji Shibata

Zeolite synthesized from coal fly ash has many intelligent properties such as cation exchange, adsorption, catalyst and so on. The suitable use of the zeolite, however, is not established in an actual commercial scale yet. From the viewpoints of an effective usage of coal fly ash and the zeolite obtained from coal fly ash, we propose the new concept for environmentally friendly usage of zeolite, in which coal fly ash safely returns to the soil with growing plants and purifying wastewater. This method can make great contribution to recycle of coal fly ash, to purification of high nutritious water and to tree planting.

Jan 1, 2002

By Gaballah Djona M.

Spent hydrorefining catalysts contain about 5 % of CoO and/or NiO, 12 % of MoO3 and up to 10 % of V205. They are generally supported by alumina and contain up to 25 percent of C, S and hydrocarbons. Such materials are potentially hazardous to the soil and to water resources. Selective chlorination of raw unroasted samples with Cl2 + air gas mixture had been investigated. At temperatures lower than 600 °C, it was possible to recover more than 90 % of nickel and cobalt chlorides, about 99 % of the molybdenum and up to 75 % of vanadium chlorinated compounds. CoCl2 and Ni/Cl2 were extracted from the chlorination residues by their dissolution with acidified water. Molybdenum and vanadium chlorinated compounds were recovered by selective condensation from the vapor phase. The chlorination of Al2O3 could be limited to less than 6 %. The scale up of this treatment was successful and a flow-sheet is proposed.

Jan 1, 1995

By S. Street

The Environment process, invented by Prof. H.K.Womer and developed at the University of Wollongong, simultaneously treats ferruginous and organic wastes via bath smelting. Conceived in the late 1980&apos;s, the patented process was originally developed using steelworks dust to settle solids from sewage, producing a composite material suitable for smelt reduction. Work began on the process in 1990 with the Australian patent having a priority date of February 1990. Early research focussed on settling of solids from sewage, while pyrometallurgical investigations examined smelting in small induction furnaces. By 1992 smelting trials had been undertaken in pneumatic and electric arc furnaces, the process being successfully demonstrated up to on 8 tonne scale. The success of this particular trial, and other smaller trials, resulted in construction of a 100kg DC arc furnace which was commissioned in 1993. By 1994 the main project focus was on development of the smelting technology. Over 3 years of trials on the DC arc furnace have identified and clarified many of the pyrometallurgical reactions. optimum operating parameters, as well as demonstrating the versatility of the process for treating a wide range of wastes. Currently the Illawarra Technology Corporation (lTC), the commercial arm of the University of Wollongong, is pursuing commercialisation of the process.

Jan 1, 1996

By Martin Brueggemann

In 1993, the El Paso Smelter began operation of the first commercial CONTOP copper smelting furnace. The CONTOP process was chosen for the plant modernization due to its low capital cost and the ease that it could be incorporated into a 100 year old existing smelter. After four years of operation, CONTOP has proved itself to be a reliable copper smelting technology. This paper will discuss a brief start-up history, current operation, and future modifications and improvements.

Jan 1, 1998

By Qinmeng Wang

The oxygen bottom blown copper smelting process is a new technology which has been widely applied to the copper production in China. In this work, a computational thermodynamics model for this technology has been established, based on smelting mechanism and theory of Gibbs free energy minimization. The calculated results from the model agree well with the actual industrial data, indicating that the model can be used for the predictions under different operating conditions. The tendencies of the key parameters (such as Cu losses and Fe3O4 content in slag) and the distribution ratios of the minor elements (such as Pb, Zn, As, Sb and Bi) can be predicted by adjusting the oxygen/ore ratio charged into the bottom blown copper smelting furnace. The model can be used to monitor and optimize the industrial operations of the oxygen bottom blown copper smelting process.

By Yimin Ruan

"An inverse design method is developed to obtain the optimal cooling conditions for the continuous quenching of precipitation hardenable sheet alloys to achieve the required yield strength. The yield strength of a precipitation hardenable alloy is obtained by allowing solute to enter into solid solution at a proper temperature and rapidly cooling the alloy to retain the solute in the solid solution. An aging process may be needed for the alloy to develop the final mechanical properties.The objective of the design is to optimize the quenching process so that the required yield strength can be achieved. With the inverse design method, the required yield strength is specified and the sheet thermal profile at the exit of the quenching chamber can also be specified. The conjugate gradient method is used to optimize the cooling boundary condition during quenching. The adjoint system is developed to compute the gradient of the objective functional. An aluminum sheet quenching problem is presented to demonstrate feasibility of the inverse design method.IntroductionQuenching is a critical step in metal production to achieve desired material properties, such as yield strength, hardness, etc., for precipitation hardenable alloys. In most cases, rapid quenching from the solution heat treatment temperature is necessary to obtain the required material properties, but rapid quenching may cause other problems such as excessive distortions of the quenched materials.In a solution heat treatment, the alloy is heated to a suitable temperature, held at that temperature to allow the soluble alloying elements to enter into the solid solution, and cooled rapidly (quenching) to retain the alloy elements in the solid solution. An aging process, which controls precipitation of fine particles at room (natural aging) or elevated temperatures (artificial aging), is generally followed after the quenching process to develop the final mechanical properties of the heat treated alloys."

Jan 1, 1998

By R. Schuhmann

The thermodynamic data and calculations which underlie the design of the Q-S process for coppermaking are summarized. The efficient production of crude copper and slag of low copper content in a single con¬tinuous converter requires the establishment and control of gradients in oxygen activity and other physico-chemical variables throughout the reactor. These gradients are established by stagewise introduction of oxygen and solid feed materials to provide: (a) flash oxidation of sulfides above the bath, utilizing the great bulk of the oxygen, (b) conversion of high grade matte or white metal to crude copper by bottom blowing with restricted bath turbulence, (c) close approach to equilibrium staging of converting and deconverting reactions along the length of the slag layer, from a maximum oxygen activity near the metal discharge end to a minimum at the slag discharge end, and (d) completion of slag cleansing by deconverting. In terms of the Phase Rule, the Q-S process involves a system with a minimum of 5 components (Cu, Fe, S, O, and SiO2) and several liquid, solid, and gaseous phases. Accordingly, basic data from previously reported studies on simpler systems are utilized to prepare an equilibrium diagram for the 5-component system and to generate a quantitative thermodynamic model for the Q-S process. This model shows in particular the ranges of oxygen activities (measured by equivalent CO2/CO ratios) involved in the Q-S process and the relations of oxygen activity to temperature and other important physico-chemical variables of coppermaking.

Jan 1, 1976

By A. McLean, S. Dawson, N. D. G. Mountford

"IntroductionIn order to predict the accepted industrial practice for the year 2000, it may be helpful to first consider the rate of development of scientific knowledge. If the speed with which man can travel on commercial vehicles is taken as a criterion for determining the rate of progression, then it can be seen from Figure 1 that advancement in our present century is very rapid. Likewise, if computer technology is used as a criterion for the measurement of scientific advancement, it becomes evident that technological evolution can be highly exponential. These two examples are sufficient to demonstrate that engineers and managers cannot afford to regard scientific development as being linear with respect to time if they are to avoid underestimating the needs of society.Within this framework of overall development, the time required for individual ideas to progress from inception to regular application has decreased considerably. For example, X-rays first discovered by Roentgen in the 1890's and now used widely in medicine and engineering, required a developmental period of some eighty years. The motorcar evolved from early beginnings at the turn of the century to a position of great social impact in sixty years. Rectifier materials used in high frequency radar to the present explosion in communications, required forty years. As illustrated in Figure 2, the period is shortening rapidly.The use of sound waves appears to be following a similar path. There is now a considerable body of knowledge concerning their behaviour and exceptional advances have been made. In medicine and engineering the sonic approach to examination is well established, and acoustic testing forms the basis of several diagnostic and quality control applications. With respect to metals engineering, ultrasonic testing has contributed to the understanding of the relationship between the size and number of internal defects and the probability of premature failure. This has allowed the designer to incorporate appropriate safety factors in his designs; but more importantly, the realization of the deleterious effect of inclusions on the performance of the final product has resulted in a continuous pressure on the material suppliers to reduce the number of defects in their products.It is not only the designer who is demanding defect free material but also the fabricator, as material breakdown during manufacture can be prohibitively expensive. Examples of this can be found in both the aluminum and steel industries where ultra clean sheet is required to ensure that rejections are minimized during beverage can manufacture and other deep drawing operations."

Jan 1, 1988

By Ljiljana Solujic

The need for the removal of mercury from the precious metals extraction circuits may be influenced by process, environmental, as well as by occupational hazard reasons. In these circuits mercury is mainly present as cyanide complexes. The effectiveness of any stabilization method will be influenced by the high thermodynamic stability mercury-cyano species exhibit in an aqueous solution. In this study, we have investigated the utility of the trisodium salt of trimmercapto-s-triazine (TMT) for precipitation of mercury from the corresponding cyano-complexes. The influence of pH molar ratio of TMT to Hg, coagulant and flocculant additions, excess of free cyanide, as well as the presence of other metal-cyano species on the effectiveness of mercury precipitation were investigated in detail. Also, a "teal world" precious metals mill effluent initially containing ~7 ug/mL (ppm) of Hg was treated and A was found that greater than 99.8% of the mercury was removed from the solution as am insoluble Hg/TMT complex.

Jan 1, 1996

By J. Szekely, S. Rhee

"A mathematical formulation has been presented to describe heat and fluid flow phenomena in CVD operations. In the statement of the problem, which included consideration of plasma enhanced CVD systems, emphasis was placed on identifying the parameters which play a key role in determining the rate and the spatial uniformity of the deposition process. This was done both through the appropriate dimensionless groups and by presenting an extensive set of computed results. The main conclusions that may be drawn from this work are that the deposition rate will be inherently non-uniform for atmospheric CVD systems; this may be somewhat ameliorated by inclining the susceptor or changing the vessel contours. Operation at greatly redeced pressures and for PECVD systems will give a much more spatially uniform deposition rate.1. INTRODUCTIONIn recent years, there has been a growing interest in chemical vapor deposition techniques for the preparation of thin films for semiconductor, photovoltaic applications and for coatings in general, as evidenced by numerous journal articles and symposium proceedings devoted to this topic (1-6). An interesting variant of this technique is to perform the deposition in a plasma or glow discharge at low pressures because this technology obviates the need for the thermal decomposition of the precursor at the substrate surface and permits operation at greatly reduced temperatures (7-10).By far, the largest portion of the reported work dealing with both these aspects of the technology has been concerned with the characterization of the deposit, quite properly so. However, in more recent times it has been realized that the transport aspects of these processes are also deserving of attention because the understanding of heat flow, fluid flow and diffusional phenomena may provide the key to the solution of problems associated with obtaining uniform deposits and the proper scaling of laboratory measurements in order to design industrial CVD systems."

Jan 1, 1986

By Mark Osborne, Ray D. Peterson, C. Edward Eckert

"The theoretical melting energy requirement for a typical hypoeutectic aluminum-silicon alloy is approximately 520 BTU/lb. It has been demonstrated, however, that even a state of the art secondary processing-automated lost foam casting operation can exceed this value by at least an order of magnitude when the actual thermal energy input from melting to solidification is monitored. Metal transfer and holding operations constitutes over 65% of this expenditure. The authors present relative benchmark energy expenditure information by unit operation for an offsite melting/lost foam casting line with a daily throughput in excess of 100,000 lbs. Efficiency improvements through optimization of the current process, and anticipated energy values at the culmination of a U.S. Department of Energy sponsored project to develop, integrate and demonstrate an advanced melting, transportation, and dispensation system will be cited.IntroductionThe size of the U.S. aluminum remelt pool was approximated to be 14.21 billion kg (31.27 billion pounds) by a recent study?, with the engineered castings (foundry) sector accounting for 3.25 billion kg (7.16 billion pounds) or 23% of that total. This study considered overall process yield and all major contributors to scrap. The values cited, therefore, are more meaningful than simply tabulating annual pounds shipped by sector.The foundry sector consists of Sand Castings, PM Castings and Die Castings categories appearing in Figure 1. All other categories comprise the wrought alloy sector. Wrought alloy production enjoys an energetic benefit from both scale and a relatively continuous operation. Many foundry operations, however, operate in batch mode at less than design metal throughput with characteristically longer melt holding periods. Since any detention of molten metal beyond melting represents an overhead use of energy, melt holding (secondary) energy expenditures can appreciably inflate melting energy requirements in the foundry."

Jan 1, 2009

By Farhang Hedjazi

Anglo Asian Mining have recently installed an industrial-scale UF/RO plant to treat process liquors from the integrated heap leach/agitation leach/ resin-in-pulp gold ore treatment facilities at their Gedabek gold-copper mine in Azerbaijan. The UF/RO plant is designed to treat 60 m3/h of leach solution to produce discharge quality water. The RO concentrate, which contains elevated concentrations of copper, silver and cyanide, is sent to the company’s SART plant for the recovery of the metal values as a precipitated sulphide concentrate and the cyanide, which is recycled to leaching. The new water treatment plant improves the sustainability of the operations at Gedabek by enabling replacement of fresh water input with RO permeate and safe discharge of permeate to the environment, during periods of excess water balance. The paper includes pilot plant data and early results from the full-scale plant.

By . Menad Gaballah I

Three samples of solid wastes generated by the non ferrous metallurgy were characterized. These residues contain up to 42 % of valuable metal compounds ( Cu, Pb and Zn ) and 23 %of toxic compounds t As, Hg, Cd and Se ). These sample were subjected to thermal treatments between 200 DC and 800 °C in controlled oxidizing. reducing and chlorinating atmospheres. Up to 99 % of As, Cd, Hg and Se were eliminated from these industrial wastes. Cu, Pb, and Zn compounds were concentrated in the treatments&apos; residues of these samples. A Global Decontamination Factor&apos; GDF &apos; was defined to measure the efficiency of the elimination of toxic elements and the recovery of valuable elements for a specific sample submitted to a given treatment. It seems that the thermal treatment in a reducing atmosphere was the most efficient in decontaminating these solids and the concentration of valuable elements. a.

Jan 1, 1995

By Dirk Verhulst

The Altair Hydrochloride Pigment Process is a new ?third route?, besides the established high-temperature chloride process and the older sulfate process, to manufacture TiO2 pigment from ilmenite ore. It has been tested at a scale of 5 t/day feed. The ore concentrate is digested in high-acid, high total chloride solution (+/- 39% Cl). Titanium and iron both go into solution. Iron is separated as FeCl2 crystals after reduction and cooling. Titanium is transferred by solvent extraction into a purified, high-Ti stream. It is spray-hydrolyzed to produce a TiO2 hydrate and further calcined with additives into high-quality pigment. HCl solutions generated by pyrohydrolysis and spray hydrolysis are treated by pressure-swing distillation to regenerate HCl gas for re-injection into the digestion reactor. All chloride streams are recycled. Recent work has concentrated on optimization, particularly in 3 areas: - Solvent extraction: a new organic mixture, including a new diluent, makes it possible to work at room temperature, to avoid TiO2 hydrolysis problems and to improve phase disengagement and impurity separation. - Pigment finishing: a systematic study of the parameters involved, followed by long runs in the best conditions confirm pigment quality. - Flow sheet optimization: innovative modifications of the conditions of spray hydrolysis and pyrohydrolysis, combined with re-routing of streams achieve significant energy savings. A 100 t/year pilot plant including these features as well as other process improvements is under construction.

Jan 1, 2006

By Yuan She, Qihang Liu, Keng Wu, Hailiang Ren

By observing different coal char’s microstructures and microscopic morphologies during the coking process, the characteristics of COREX coal char’s microstructure and properties were analyzed. MCRI and MCSR were used to respectively describe the reactivity and the strength after reaction of coal char, with those of BF’s coke for reference, and then the physical meaning of MCRI and MCSR were given. MCRI and MCSR were determined by the composition of coal char. For the two kinds of COREX coal, the formula to forecast the hot performance of coal char was set up by making a multiple linear regression between the hot performance and microstructure of the coal char at 1100℃, and the predictive values of coal char’s hot performance at 600℃, 800℃ and 1000℃ coincided well with the measured values.

Jan 1, 2015