Search Documents

By J. B. Winter

The present Inspiration Consolidated Copper Company Smelter/Acid Plant complex located near Miami, Arizona, was designed and built specifically to conform to the ambient air quality standards imposed by the Federal Clean Air Act of 1971. The present plant replaced a facility which had been in operation since 1915. The electric furnace, siphon converters and acid plant complex were commissioned in May, 1974 (1). At that time, the Plant was considered to be one of the most extensively monitored and instrumented facilities of its kind in the world. Several control areas were located in close proximity to the controlled process, in addition to so-called central control rooms in the Smelter and Acid Plant. The control rooms were staffed with officials below the foreman level. Instrumentation consisted of conventional analog devices, except for a computer used in monitoring ambient air environmental conditions and limited use of programmable logic controllers. The harsh service conditions prevalent in the plant rendered a significant portion of the instrumentation unreliable and, in many cases, inoperable. Failure of the facility to obtain the total sulfur collection for which it was designed was, in part, due to serious inadequacies in control system logic and sulfur recovery averaged 79% in the early years. After careful study of the smelting process, engineering hardware and high labor cost inherent in the organizational structure, management made a judgement decision to convert to centralized control of the process with high level supervision 24 hours per day. A distributed digital control system with supervisory arid data acquisition/information reporting computers was selected to satisfy the requirement of central control. Operations are now controlled and coordinated from a primary control room in the Smelter and a satellite control area in the Acid Plant.

Jan 1, 1983

By B. Qiu, Y. Luo

Longwall and/or room-and-pillar mining operations in multiple coal seams may not only induce subsurface and surface subsidence but also cause interactions between these mined coal seams. The interaction might destabilize underground mine structures and subsequently induce additional strata movements. Mathematical models to use the predicted subsurface deformations to assess the interactions and the consequences have been developed. The models are incorporated into a computer program, CISPM-MS, for predicting the final surface movements and deformations, as well as the mining interactions associated with multiseam coal mining operations. It predicts final surface movements and deformations caused by the individual mining operations and by the interactive effects. The program can also be used to assess mine structural stability in multiseam mining operations. The paper presents the developed interaction models and their application in surface subsidence prediction caused by multiseam mining operations. A case study involving mining in two coal seams, using longwall and room-and-pillar mining methods, respectively, will be used to validate the program.

Jan 1, 2013

By Joseph W. Richards

This method of briquetting flue-dust, or flue-dust mixed with fine ores, or, in a few exceptional cases, coke-dust, has come into large commercial use in Europe, and a small plant is already in operation in the United States. It promisea to become of such great importance to the iron industry of the United States that the following description will certainly interest the majority of our pig-iron producers. Discovered in 1908, the process Tests upon the observation of Dr. Schumacher that blast-furnace flue-dust, while possessing of itself no binding or cementing properties, acquires strong cementing properties if mixed with a very small amount of certain salt solutions, the amount of which is so small that the resulting cementation appears to be rather by catalytic action of the salts added than by the mass-action of such chemicals. To be more specific, fresh blast-furnace flue-dust mixed with from 5 to 10 per cent. of its weight of magnesium chloride or calcium chloride solution—that is to say, with from 0.25 to 2 per cent. of its weight of magnesium chloride or calcium chloride—acquires the property of setting within a short time, from 15 to 60 min., and forming a hard cemented briquette. Alkaline solutions appear to have no action such as described, and they even interfere, if present, with the action of the magnesium and calcium solutions. When treated in this way the flue-dust briquette sets very hard, apparently from pure excess of cementing- and setting-power. It is, therefore, possible to mix with the flue-dust a considerable proportion of inert ore or like material, which has no setting-power by this process, and thus to make a compound briquette containing large quantities of ore mixed with flue-dust, but in which the flue-dust may be regarded as the cement or binding-material. A particularly strongly cementing flue-

Jan 1, 1913

By Ralph J. Holmes

"An accurate knowledge of the chemical, mineralogical and physical characteristics of ores and mineral products that are mined, processed and sold commercially is crucial to resource definition, effective resource utilisation, plant design, process control, metallurgical accounting and finally quality control to ensure that contract specifications are met and equitable payment is received for product sales. However, the responsibility for sampling is often entrusted to personnel who do not fully appreciate the significance and importance of collecting fully representative samples for analysis, and they seem satisfied as long as some material is collected and returned to the laboratory for analysis. Furthermore, sample stations incorporated into the design of new plants are often the first casualties when cost cutting exercises commence. There is really little point in accurately analysing samples if they are not representative in the first place, because the resultant analyses can be seriously biased and the effort taken to carefully analyse such samples is largely a waste of time and resources.Ultimately, a poor knowledge of the characteristics of ores and mineral products limits the ability of mining companies to optimise the life of ore resources and plant performance, and failure to meet final product specifications can have disastrous consequences, including price penalties and more seriously loss of sales contracts and significant revenue losses due to poor sampling practices at the point of sale. Consequently, it is critical that sampling is given the attention it deserves as the first important step in the quality measurement chain. The golden rule for correct sampling is that all parts of the ore, concentrate, slurry or other material being sampled must have an equal opportunity of being collected and becoming part of the final sample for analysis."

Jan 1, 2016

By Pedro Lucas Freitas

A elaboração de planos de mistura é feita em uma coqueria para uniformizar a qualidade das misturas. Um problema recorrente é a distribuição destes carvões nas dosadoras para serem misturados. A distribuição, no plano, destes carvões nas dosadoras é feita de forma manual, levando em consideração apenas o conhecimento do operador. A proposta é apresentar uma modelagem matemática de programação linear para resolver o problema da distribuição de carvões em dosadoras, segundo restrições de utilização das dosadoras dentro da faixa ótima, composição da mistura e uniformização das correias transportadoras, para reduzir sobrecarga nas linhas de dosadoras, com a finalidade de execução de um plano de mistura de carvões. Foram utilizados métodos de pesquisa operacional utilizando o algoritmo Simplex.

Aug 16, 2017

By Robert T. Langland

The Bureau of Mines, at its Denver, Colo., research center, has developed a computer program to solve nonlinear regression problems. The program is written in a general form so that, regardless of the functional relationship assumed, the unknown parameters may be evaluated by the Newton-Raphson method of iteration. Variances and covariances of the parameters are derived, based on the propagation of errors. A creep function is established from shale test data as an example of program utility. Program accuracy is compared to the accuracies of other programs in present day use.

Jan 1, 1974

By Denholm WT

A mathematical model has been developed for intense pneumatic smelting processes, such as the Sirosmelt group of processes, to assist in establishing optimum process conditions and to permit operator training. The model first solicits input operating conditions from disk files and from the operator. During operation, the feed, fuel, and air (or oxygen) rates are automatically adjusted to maintain the desired process targets. Alternatively, these parameters, as with all other inputs, may be manually controlled by the operator. Selected process parameters are displayed to the terminal in a regularly updated diagram of the process,. Outputs of detailed information including heat and mass balances are available for immediate inspection or for use by ancillary plotting packages. Development of a robust free energy minimization routine has led to a flexible and time efficent model capable of handling a range of pyrometallurical systems. Modelling of tin smelting, lead smelting, copper smelting, matte fuming, and pneumatic steel-making has been sucessfully carried out. Typical outputs from the model are given and discussed in terms of their internal consistency and relationship to the operation of the relevant Sirosmelt process. `

Jan 1, 1984

This paper describes the back analysis of the Pavoncelli tunnel, an hydraulic tunnel which was excavated between 1904 and 1915 in South of Italy and experienced severe damages during the 1980 Irpino-Lucano earthquake. A numerical simulation which is intended to study the behaviour of the tunnel during this seismic event is presented, also accounting for the swelling phenomenon that took place during and after construction.

May 1, 2009

By Armando Gallegos Monteagudo

El presente texto señala las experiencias realizadas en GERENS, empresa de consultoría y capacitación en gestión del sector minero, formulación, implementación y control de planes estratégicos que utiliza herramientas con un alto nivel ambiental en la creación de valor económica, ambiental para las empresas mineras el Balanced Scorecard (BSC) y el análisis de la cadena de valor de la empresa. El Balanced Scorecard es una herramienta gerencial que apoya la implementación del plan estratégico y permite su monitoreo y control. Para ello, el BSC requiere que el plan estratégico de la empresa se traduzca en objetivos claros y medibles, indicadores, líneas de base, metas, y programas de acción estratégicos y tácticos.

Sep 12, 2005

By J. E. Jennings

The problems of slope stability in open-cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the ore body, This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ.

Jan 1, 1963

By L. W. Kelly

The purpose of this circular is to show that, under the conditions prevailing in the Stony Point mine, wooden bolts were just as satisfactory as steel bolts or conventional timbering, with a reduction of approximately 80 percent in cost of material. This one fact alone is enough to justify an experiment with wood. This circular will show that production records have remained constant with both wooden and steel roof bolts. INTRODUCTION The successful use of steel roof bolts is now an accomplished fact in the coal industry, but the use of wooden bolts in place of steel is a rarity. The first experiment with wooden roof bolts was mane in 1949 in the Rio Verde mine, Norton Coal Corp., Nortonville, Ky.2/ This experiment was successful; the company obtained excellent results, but operations in the mine were suspended before enough time had elapsed to prove the value of wooden roof bolts conclusively. It is obvious that, if wooden roof bolts could be used in place of steel bolts or conventional timbering-methods, every mine operator would use word, as the cost is only a fraction of the other two methods. The Stony Point experience has proved conclusively that, under certain conditions and with a certain type of roof, wooden roof bolts can be used successfully.

Jan 1, 1952

By Peter F. Steidl

Seven degasification wells have been completed in the Pittsburgh coalbed at the new Emerald mine near Waynesburg, Pa. Funding was provided by the Bureau of Mines to perform stimulation treatments on five of the wells, to show that this is a feasible and economical means of degasifying part of a coalbed. The seven wells ranged in depth from 590 to 910 feet. Stimulation treatments used 25,260 to 42,660 gallons of foam and 7,400 to 12,800 pounds of 20/40-mesh prop sand. Pumping rates were 10.8 to 11.6 bbl/min and treating pressures were from 1,050 to 1,600 psig. On the day following stimulation, gas production ranged from a few hundred cubic feet per day to more than 100,000 cu ft/day.

Jan 1, 1978

The dissolution kinetics of cobalt in iodine/iodide solutions was investigated using a rotating disc technique. Variables studied here included temperature, rotating speed, concentration of lixiviants, and pH of the solution. The overall dissolution reaction was found to be limited by mass transfer of tri-iodide through the diffusion boundary layer with Arrhenius activation energy of less than 16.2 kJ/mol (4 kcal/mol) over the temperature range, 2-42°C. The pH of the solution had little effect as long as the pH of the solution was less than 8. However, when the pH of the solution became greater than 8, the dissolution rate decreased dramatically due to passivation. The rate of dissolution was in good agreement with the dissolution model developed by the authors earlier.

Jan 1, 1994

By Palma O. Manuel

El presente texto describe el desarrollo de la actividad aurífera, así como el análisis de las técnicas y los métodos de explotación en los yacimientos detríticos de oro. En ese sentido, se analizan los criterios sobre el proceso de explotación y los resultados de dichas investigaciones realizadas por el Instituto Geológico Minero y Metalúrgico.(INGEMMET). Asimismo refiere los depósitos auríferos, perforación, explotación y concentración gravimétrica, metodología de la explotación y la amalgamación en la mina.

Nov 8, 1982

By Pedro Alejandro Samané Tuni

El presente texto describe la metodología de investigación adecuada para la excavación subterránea a través de la clasificación geomecánica según: RMR (Bieniawski), Q (Barton), Romana, Deere y Palmstrom, quienes determinan los tipos de sostenimiento y el span de autosoporte para cada tipo de roca e influyen en el método adecuado de excavación según clasificación de excavabilidad. Sin embargo, no se encontró el método adecuado y solo se define cuál de estas clasificaciones son factibles de usar en la excavación de cada tipo de macizo rocoso.

Jan 1, 2016

By B. B. Agrawal

Iron ore fines is an area of concern in India. A possible avenue is to use these fines for sponge ironmaking. Work has been carried out to pelletize these fines with coal and a suitable binder, and cure them in ambient atmosphere to retain in-situ reductant. Pellets were characterized for physical strength and metallisation. Critical factors were granulometry was percentage of coal & binder. In laboratory tests, pellets got metallized faster compared to lump ore. Large-scale trials were conducted in a 12-meter long rotary kiln plant. For 90% metallization, required residence time was only 60 minutes against 240 minutes for lump ore. Coal requirement also decreased. Investigations established the fast reduction nature of pellets. This is due to reduction-reactions occurring simultaneously at many sited within the composite pellets, in addition to the diffusion of reducing gases from the surface of the pellets to its core. The developed process is a value addition in the conventional pelletmaking and is environment-friendly also.

Jan 1, 2006

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By Matthew Preedy, Anthony Pooley, Mike Wongkaew, Dirk Bakker, Raghu Bhargava

Sound Transit’s ST3 program will add 62 miles of light rail to the Puget Sound area, including connections to the neighborhoods of West Seattle currently anticipated by 2031 and Ballard by 2036. These connections include considerations for both elevated and tunnel alternatives, as well as a new downtown tunnel for which different configurations are being considered with potentially very different construction logistics and risk profiles. This paper describes the latest developments in the ongoing evaluation process that will inform the consideration of different tunnel and station construction methods, technical and operational challenges and contracting methodologies, including construction of deep stations in dense urban environments.

Jun 13, 2021

By Finlay, J. S.

THE North Lily Mine started its career in an unusual way it was discovered by a geologist. The remarkable circumstance of driving a 2400-ft. drift into an unexplored country and "hitting her on the nose," indicates that geologists are sometimes numbered among those whom the Lord loves. Diamond- drilling from surface had previously shown the presence and position of the Ophir beds, and surface showings of pebble-dykes, faults, and bleached rhyolite indicated conditions similar to those at the Tintic Standard "Pot-hole." The discovery drift from the Tintic Stand- ard 700-level reached the North Lily orebody in January, 1926, and development and stoping were continued by Tintic Standard men and equipment until the North Lily shaft was sunk and put into service in May, 1928. The discovery drift was run on a cooperative basis by the Tintic Standard and North Lily mining com- panies. Finding the North Lily mine cost the North Lily company $26,000. The Tintic Standard Mining Co. furnished men and equipment to drive this discovery drift at a fraction of what it would have cost to find the orebody from surface. This was the beginning of the friendly cooperation that still exists. Through Tintic Standard ground the Tintic Standard paid two- thirds of the cost and the North Lily one-third; the cost of the drift through Eureka Lily, into North Lily ground, was paid by North Lily. Later, another drift from the Tintic Standard 900-level was run on the same plan, excepting that Eureka Lily paid its share of the cost; that is, the Eureka Lily paid one-third of the expense in Tintic Standard ground, and the Eureka Lily two-thirds and North Lily one-third in Eureka Lily ground. This 900-drift was driven by North Lily from the Eureka Lily line to near the North Lily west side-line. From this point the Chief Consolidated continued the drift well into Tintic Bullion ground.

Jan 1, 1929