Search Documents

By J. H. E. Jeffes, K. T. Jacob

Solid oxide galvanic cells, of the type: Pt,Ni-NiO | Solid electrolyte | O(metal),Cermet,Pt, were used to measure the activity coefficient of oxygen in liquid Cu at 1 100 and 1 300°C and in Pb at 1 100°C. Similar cells were used to study the activity coefficient of oxygen in the whole range of Cu + Pb alloys at 1 100°C and in Pb-rich alloys at 900 and 750°C. The results obtained are discussed in terms of proposed solution models. An equation based on the formation of 'species' of the form M(2)O in solutions of oxygen in binary alloys is shown to fit the experimental data

Dec 1, 1971

By X. Gumede

Mud houses are common structures in most South African rural homes closer to the mining operations. Fulltime dwellers in these properties are often the elderly. The mine codes of practice and the South African legislative instruments attempt to define the damage criteria to limit the effect of the blast-induced noise and ground vibrations to different structures. All these assessment criteria are based on the peak particle velocity and noise generated during blasting. The South African safe limit criterion that was adopted was initially derived from the international standards, which were then used as a local guideline. This paper evaluates the currently adopted safe limit criteria used in South Africa for a mud house, currently rated at 6 mm per second and 120 decibels to134 decibels, for blast-induced seismicity and noise, respectively. Further, a study was performed on a residential house near a coal mine (5.26 km) based in Mpumalanga following numerous complaints by the owner, launched at the mine and to the Department of Minerals and Petroleum Resources. The aim of the study was to measure the magnitude of blast-induced triggers experienced at the aggrieved homestead and to establish if there is a likelihood that an irritation or damage may be caused by these triggers. The seismometer was installed at about 2 m from the mudhouse, from 1 July 2022 to 31 of July 2022. Five blast-induced triggers were recorded during the period showing an average of 0.09 mm/s and 121 decibels for blast-induced seismicity and noise, respectively. The results obtained indicated a maximum seismicity of 0.15 mm/s. This seismicity was below the perceptible vibrations obtained from daily home activities such as walking, jumping, and door slamming, which produce 0.8 mm/s, 7.1 mm/s, and 12.7 mm/s, respectively. Seismicity was therefore not likely to have caused any annoyance and or damage. For noise, the results indicated a maximum of 123 decibels and an average of 121 decibels from five events recorded. A literature review suggests that slight damage may occur when airblast frequencies match the natural frequencies of structures at 120 decibels. Based on these results, it can be concluded, therefore, that the noise, rather than seismicity, is more likely to be the cause of damage to the structure assessed. For improvement, a new approach is proposed based on relating the safe limits to the structural and human response.

Dec 15, 2025

By I. Gombköto

In the EU-region, the automatically operated approximately 200 (rotating hammer) shredder plants processing large technical equipment (end-of-life vehicles, large household appliances) annually produces 8-9 million tons of non-metallic grinded by-product, which ends in landfills, without recovery. Although this by-product is organic material, still contains large amount of metal components worth recycling. These operations, such as shredding and processing end of life vehicles or mixed metal components are a growing market and it is become more potential if EU directive 2002/96/EC will become obligatory for new member and candidate countries and they have to apply EU regulations. Eddy current separators (ECS) are one of the most important units of separation of non-ferrous metals from insulators in waste recycling. The product of ECS processing of shredded ELV?s is usually a mixture of Al, Cu, Brass and stainless steel. This mixture has relatively low price on the market, while purified metal products are required by smelters for which shredder operators are able to get even higher price. Our aim at University of Miskolc was to find solution producing pure metal products using dry separation processes. Authors are presenting a possible solution, using ECS. Institute of Raw Material Preparation and Environmental Processing possesses an ECS, equipped with 305 mm wide belt, and a concentric magnetic rotor. The subject of our work was to investigate the behaviour of model particles with different shape, conductivity (aluminium and brass), orientation and size in order to separate Al and Brass. We used model particles with similar shapes of shredder plant originated ones. The magnetic flux and magnetic frequency was constant and derived by the design of the rotor. During our research work, belt speed and rotor speed of ECS were varied. The particle distance and trajectory caused by throwing was determined and the results are reported in this paper.

Sep 1, 2012

By William W. Adams

The quarrying and related industries of the United States made a large gain in employment (man-hours of work) in 1942 with a somewhat smaller number of men employed than in 1941. This was accomplished chiefly by increasing the number of workdays per man and also by increasing the length of the workday. In spite of the greater volume of work performed, the industry had a more favorable accident-frequency rate in 1942 than in the previous year. Accident and employment reports from operating companies showed that the industry employed 84,270 men for an average of 271 days per man in 1942, with a volume of work of almost 181 million man-hours. The average workshift comprised 7.93 hours, and the number of man-shifts worked totaled nearly 23 million. Injuries from accidents in and about the quarries and plants caused disability to 6,461 employees, 112 of whom died as a result of their injuries, including 28 employees whose lives were lost in a single disaster. The accident-frequency rate in the industry was 35.73 per million man-hours worked, comparing favorably with a rate of 40.11 for the previous year. However, the figure for 1942 included a death rate of 0.62 per million man-hours which, because of the disaster referred to, was considerably higher than the fatality rate of 0.44 for 1941. Had the disaster not occurred, the fatality rate for the industry for 1942 would have been 0.46. The major disaster in which 28 lives were lost occurred on March 26 at the Sandts Eddy quarry of the Lehigh Portland Cement Co. near Easton Pa.

Jan 1, 1944

By C. F. Feng, L. Froyen

"In-situ processes have emerged as new and promising techniques for metal matrix composite fabrication. They offer significant technical and economic advantages over conventional processing. One of the in-situ processing routes that have been used is reactive free sintering of a mixture of powder reactants. However, materials synthesised via this route are always porous because of density differences between reactants and products. An example are the porous Al/(TiB2+Ah03) MMCs obtained by heating powder mixtures of Al+ Ti02+B with Ti02 and B in stoichiometric ratios for forming TiB2• In this study, porous Al/(TiB2+Ah03) composites were further processed by hot-pressing at temperatures above 600°C. This processing cycle was designed so that the composites could be densified. Furthermore, the reaction kinetics of the in-situ processing are studied by means of DSC analysis measured at different heating rates. The activation energies of the three intermediate steps that are involved in the reactive processing for preparing AV(TiB2+Alz03) MMCs are determined to be 923 kJ/mole, 241 kJ/mole and 235 kJ/mole respectively.XRD proved that the hot-pressed products consist of Al, TiB2 and Al203- Properties of the products are assessed by microstructural characterisation (LOM, SEM and EDS), microhardness, Young's modulus and bending tests. The results show that good microstructures, elastic properties and strengths, as well as acceptable ductilities were achieved. For the composition 79.74wt% Al-15.95wt% Ti0z-4.31wt% B, after the reactive free-sintering and hot-pressing cycles, Young's modulus is 105 GPa, bending strength is 509 MPa and maximum strain is 5.0%; for composition 88.73wt% Al-8.87wt% Ti0z-2.40wt% B, they are 89 GPa, 311 MPa and 8.2% respectively. It can be seen that the properties of products can be tailored by adjusting the relative amounts of reactants in green samples. Furthermore, for comparison reasons, Al and a binary system Al-Ti02 were identically processed as the ternary systems. Their microstructures and properties were studied."

Jan 1, 1998

By C. A. Rowland

When studying the feasibility of using autogenous or semi-autogenous grinding, operating and engineering companies frequently request assistance from the mill manufacturers in three areas - 1. Recommendations for studying the suitability of autogenous or semi-autogenous grinding for the specific ore. 2. Mill sizing, to accomplish required grind. 3. Recommendations on mill design and operation. Rod mills and ball mills are selected by the use of bench scale standard grindability tests and established calculation procedures, of which the most frequently used are the Bond Grindability tests and the Bond Work Index equation(1). The accuracy of these have been reviewed by C. A. Rowland in his papers, showing the correlation of work indices calculated from plant operating data and laboratory grindability tests(2)(3). The selection of autogenous and semi-autogenous primary mills has not reached the stage where mill size selection can be made from bench scale tests. Considerably more extensive testing will be necessary than required for selecting rod mills and ball mills.

Jan 1, 1974

By R. L. Bullock

For the past 30 years there has been a gradual evolution of mechanical excavating systems in underground hard rock mining applications. This paper traces many of the tests of various tools and methods to break hard rock, up to the present. The tools include impact hammers, boring machines, disc on boom mining machines, disc on revolving wheels and drums, picks and drag bits on revolving hubs, rock splitters, slot cutting systems, and with customized explosives/powder mini-blasting. While the progress has been slow, successes are being achieved in hard rock and more opportunities exist today than ever before.

Jan 1, 1995

By Stephen R. Iverson

The U.S. Bureau of Mines made an economic appraisal of the Buttermilk study area, Inyo County, California in October 1980. Results of surveys indicate no potential for metallic, non-metallic, or energy resources in the area. However, glacial till covering most of the area prevented bedrock examinations by the appraisal teams or earlier prospectors. No mining claims are known to be in the area. INTRODUCTION Present Studies The U.S. Bureau of Mines, Western Field Operations Center, searched county mining claim records and other data available concerning mineral deposits, claims, leases, production, and mining activity in the area. The Bureau conducted field work in October 1980 searching for prospects and claim locations. Fourteen reconnaissance lode and placer samples taken from the area were analyzed for gold, silver, and tungsten; a spectrographic analysis also was run on selected samples.

Jan 1, 1981

By Fredrick L. Johnson

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 25,640 acres of the 29,680-acre Devil?s Garden Lava Bed, 21,040 acres of the 28,660-acre Squaw Ridge Lava Bed, and 9,100 acres of the 12,600-acre Four Craters Lava Bed Wilderness Study Areas (OR-D01-D02, OR-001-003, and OR-001-022, respectively) in order to evaluate their identified mineral resources. The study areas are located in Lake County, OR, about 50 air miles southeast of Bend. No mineral resources were identified in the three study areas. The areas are almost entirely underlain by recent lava flows. Cinder cones occur in each of the areas; however, the best cinder occurrences are in the Four Craters Lava Bed study area. Slab lava, of facing stone quality, is scattered throughout the Devil?s Garden Lava Bed study area, and to a lesser extent, in the Squaw Ridge Lava Bed study area.

Jan 1, 1987

By Serge Ouellet

Identification and quantification of cementitious phases in cemented paste backfill (CPB) is difficult due to the fineness of tailings and the low binder content used in the mixture. Techniques such as X-ray diffraction and thermogravimetry were ineffective (mainly due to tailing mineral interference) to identify and quantify hydration products in most works reported in the literature. On the other hand, scanning electron microscopy (SEM) was used in many cases but mainly for qualitative purposes. This paper presents the development of a new approach based on a computer program (SEM-XMAP) that combines X-ray dot mapping images acquired by SEM and generates a coloured image representing the mineralogy and the microstructure of a given CPB specimen. The technique is applied to one CPB sample mixed with blast furnace slag (BFS) and acidic sulphated mixing water sampled in a mine dewatering system. The technique allowed identifying calcic matrix, unhydrated and partially hydrated BFS particles, and sulphated phases.

May 1, 2007

By E. Salinas R.

This work is related with a whole characterization of cantera stone, to establish its characteristics that can give it an additional value for the reuse and reutilization of dust, slurries and small pieces of stone which can be treated as wastes. The obtained results reflects that the residues studied can be used as substitutes of feldspars in the production of pieces of ceramic, and also in the elaboration of paints for the same pieces according to the mixes that can be made with the variation of Na2O, CaO and K2O. According to the humidity proofs and specific gravity done, this material can be proposed as a soil improver into hydroponics systems, leading so an important alternative for food production in zones leaking of water. In the same way, it was found the possibility of use this material as a seal 3A in processes of asphalting of roads, highways and streets.

Jan 1, 2009

By H. Polat, Q. Hu, M. Polat, S. Chander

"The electrostatic charge on spray droplets of ionic surfactant solutions and coal particles was measured and the results were correlated with the dust collection efficiency. When various surfactant were added, the magnitude of the droplet charge increased significantly and it was observed to be a function of surfactant type and concentration. The concentration of maximum droplet charge coincided with surfactant concentration where maximum collection efficiency was observed for these surfactants. Particles of coal also carried substantial amount of charge magnitude of which seemed to be a function of coal rank.Based on the results presented in this paper, it was concluded that ionic surfactant primarily act as a strong electrostatic charge inducer for droplets. Due to interactions between these highly charged droplets and naturally charged particles, the efficiency of droplet-particle collisions play a primary role when compared to the wetting and engulfment phenomenon which could only follow a successful collision. INTRODUCTIONWater spray are widely used to suppress airborne dust in mine atmospheres (Walton and Woolcock, 1960; Kobrick, 1970; Hamilton, 1974; Jayaraman et al., 1986). Several investigators have considered the use of surfactants to enhance the effectiveness of water sprays especially for difficult to wet particles such as those of coal (Glanville and Wightman, 1979). The capture of dust particles by water droplets involves droplet-particle collisions, adhesion of particles to droplets, and engulfment of particles into droplets. Surfactants affect these sub processes through their influence on droplet charge, surface tension, and wetting. The last two mechanism have been thoroughly studied in recent years (Walker et al., 1952; Cohen and Rosen, 1981; Glenville and Haley, 1982; Chander et al., 1988; 1991). However, little attention has been paid to the role of electrical charge on particles and droplets on the collision and adhesion of spray droplets and dust particles."

Nov 1, 1995

A Life Cycle Assessment (LCA) of stainless steel production, including that of the nickel, ferronickel, ferrochromium and iron feedstocks was carried out using inventory data derived from the literature. The environmental impact categories considered in the study were Global Warming Potential (GWP), Acidification Potential (AP) and total (or full cycle) energy consumption. The effects of different sources of electricity (black coal, natural gas and hydroelectricity) were also examined in the study. The results of the LCA showed that when ferronickel is used as the nickel source, the total energy consumption for stainless steel production is approximately 50% higher than when nickel metal is used as the nickel source (75 MJ/kg cf. 49 MJ/kg). This result comes about largely because the Fe units in ferronickel have a much higher energy intensity than do the Fe units in pig iron, and the greater the use of the former at the expense of the latter, the greater is the total energy consumption. The results also showed that the production of ferronickel made by far the largest contribution (59%) to the total energy consumption for stainless steel production when this feedstock is used as the nickel source, but when nickel metal is used as the nickel source the contributions of the various stages are more evenly distributed. It was also observed that the electricity consumption of the electric furnaces used in the production of ferronickel, ferrochromium and stainless steel contributed approximately 50% to the total energy consumed in stainless steel production. Given the relatively low efficiencies associated with electrical power generation, significant reductions in the total energy of stainless steel production could be anticipated if more direct use of thermal energy was made in the ferronickel, ferrochromium and/or stainless steel smelting stages, for example by utilising bath smelting processes.

Jan 1, 2004

By Bruce Hebblewhite

This paper focuses on the recent achievements and practices developed through the Minerals Tertiary Education Council (MTEC) initiative of the Minerals Council of Australia (MCA), in conjunction with the three partner universities involved in mining engineering education – University of New South Wales (UNSW), West Australian School of Mines, Curtin University (WASM), and University of Queensland (UQ). The collaboration between these partner universities and industry has led to the development of shared course material, cross-institutional teaching arrangements, and development of a number of flexible, distance-based delivery programs. The paper will then move on to future initiatives. Importantly, the exciting challenge is the future initiative planned to cement this collaboration by the formation of a “virtual” national school of mining engineering – Mining Education Australia (MEA). This will provide a common 3rd and 4th year program to all three universities from 2007, involving innovative teaching and learning arrangements, greater student exchange potential and a more significant input by industry into the education process. Such an initiative is not without its challenges, and has a long way to go, before becoming a reality. However, it offers greater attractiveness and marketing potential to prospective students, as well as economic efficiencies, whilst delivering a better quality, and hopefully greater quantity of graduates to industry. It can also form a launching platform for a much greater level of international collaboration, through a proposed International Mining Education Network (IMEN) which is currently being floated amongst a number of international educators.

Jan 1, 2005

By Gerardo Soto M.

El presente texto señala el potencial mineralógica del proyecto minero Cotonga, situada en la provincia de Huari, departamento de Ancash. La investigación comprende la historia del yacimiento, fisiografía, las exploraciones geológicas y geofísicas, el desarrollo en el stock Cotonga, la geología del yacimiento de Contonga, geología estructural, económica, paragénesis y zoneamiento, el sistema de explotación y el funcionamiento de la planta concentradora.

Nov 8, 1984

By N. A. Sareyed-Dim

Nickel ores may be classified into two major categories : sulphide ores, and oxidized lateritic ores, these latter containing nearly 80% of the known reserves of the metal (1). Two types of lateritic ores are recognized; ores high in iron but low in magnesia and silica are known as "limonitic", while ores low in iron but containing high percentages of magnesia and silica are called "silicate" (see Table I). Sulphide ores can be beneficiated readily by conventional ore dressing techniques and the technology for nickel recovery from such ores has been well tested in a number of commercial processes (1-4). Unfortunately, no economically viable process for the concentration of nickel from low-grade deposits has yet been developed, and so only the high grade ores are able to be worked profitably. Silicate ores have been treated pyrometallurgically for the production of ferronickel (2) (3) (5); limonitic ores have been processed hydrometallurgically to produce nickel metal (2) (3) (6) (7).

Jan 1, 1975

By S. G. Shabestari

In the metal casting industry an improvement of component quality mainly depends on better control over the production parameters. Thus, thermal analysis cooling curve of the alloy is used for process control in aluminum casting industry. Cooling rates of the alloy during solidification process affect microstructure, grain size, eutectic silicon morphology, and dendrite arm spacing (DAS). In this research, effect of cooling rate on the microstructure and solidification parameters of 319 aluminum alloy that is a widely used alloy in automotive industry, has been investigated by means of thermal analysis. Seven different cooling rates have been obtained by using CO2-bonded silica sand molds with two different wall thicknesses, hot-work tool steel molds (H13) with and without coating, thin-wall steel molds with different coatings. In each case, cooling curve and first derivative cooling curve have been plotted by use of very accurate thermal analysis equipment. Effect of different cooling rates on solidification parameters e.g. Nucleation temperature (TN,a), nucleation undercooling (ATN,a), recalescence temperature (TR,a), solidification range (AT,s), and total solidification time (t 0 have been studied in the liquidus region. Microstructural evaluation has been carried out and DAS were measured in all solidification conditions. A numerical equation was proposed to predict cooling rates via measuring DAS in 319 aluminum alloy. Nucleation process and the effect of cooling rate have been interpreted by using thermal analysis cooling curves and microstructural study.

Jan 1, 2004

By T. A. Rickard

The notion prevails that writing is a knack, that the skilful use of the pen is a gift of nature. This is an error. Dogberry may be responsible for it; he said: "To be a well-informed man is the gift of fortune, but to write and read comes by nature". Because Dogberry said it, we may be sure that Shakespeare thought otherwise. Ability of any sort may be partly innate, but my own observation and experience lead me to conclude that most of the easy writers have become so by constant practice. As I recall the names of men successful with the pen, I remember that most of them have written a great deal and have taken particular pains to improve their style. The suggestion that proficiency in the difficult art is a happy accident provokes a sardonic smile. The larger part of the great writing in our literature is the result of persistent effort. An easy fluency has been the undoing of many; their flamboyant and fantastic scribbling has proved as perishable as froth. This criticism applies to technical writing also; in order that a technical description or discussion may hold the interest of the reader, at least long enough to cause him to read it to the end, the writing must be done carefully and systematically; otherwise it will fail in its purpose of conveying information. Clearness is absolutely essential. "It is not enough to use language that may be understood; it is necessary to use language that must be understood."* The purpose of writing, at least of that which is meant to be read by others, is not only to express ideas but to communicate them. Lack of perspicuity may prove as %ad as

Jan 1, 1931

By E. Brzychczy

Artificial intelligence techniques are ever more frequently implemented in the modern world. One of their numerous uses is supporting enterprise management. Intelligent techniques and intelligent information technology (IT) systems can be implemented in mining-related issues as well. The author of this article concentrates on supporting the process of planning mining operations by intelligent systems and techniques. The author also underlines the importance of knowledge accumulation in a mining enterprise (especially tacit knowledge) as well as its efficient storing and using. Additionally, the author provides a short description of characteristics of intelligent IT systems and indicates their capabilities in planning mining operations. She presents two solutions, namely: an advisory system which supports the process of planning preliminary works and exploitation works in hard coal mines, and a method of modeling and optimizing mining operations. Finally, the author indicates a few possible future development trends of intelligent systems - the intelligent systems of decision support.

Aug 1, 2013

By Coida D. S. Renata, Gerald Okwuchi Onyedika, Moura E. B. Esperidiana, Graca Valenzuela-Diaz, Martin Chidozie Ogwuegbu, Francisco R. Valenzuela-Diaz, Amauche Cyprian Achusim-Udenko

This work aims to incorporate Mgbee clay, vegetal fibre (Costus afer) in recycled low density polyethylene (rLDPE). The incorporation of clay and vegetal fibre in rLDPE was carried out using a twin screw extruder machine and the nanocomposites were obtained. The nano composites were characterized by the Young’s modules test, tensile tests, bending test, XRD, SEM, DSC, and TG and other properties evaluated. The results of morphological and thermal properties showed a good interaction between the clay, and rLDPE as compared to neat rLDPE.

Mar 1, 2017