Search Documents

By M. W. Hildyard

A blast was engineered close to a tunnel in a deep-level mine with the purpose of studying the wave interaction with the tunnel. Numerical modelling of seismic wave propagation was used in both the forward planning and the back-analysis of this experiment. This paper presents the forward analysis. A likely model for a propagating blast was investigated and developed. This model predicts the influence of the velocity of detonation of the blast and the rise-time of the blast on the radiation pattern, and hence on the expected positions of maximum velocity at the tunnel surface. An attempt was made to quantify the parameters of the blast model, using waveform data from two other blast experiments. The blast model caused particle velocities which were an order of magnitude lower than these measured velocities. Large values for blast pressure were required to match the amplitudes of the recorded velocities. An alternative ?effective? source with a similar mechanism but increased diameter was proposed to account for the higher velocities. It was established that distant velocities scale with the square of the borehole diameter. A calibration blast at the experimental site was also modelled. Agreement in the waveforms was not sufficient for conclusive statements to be made about the validity of the source model. However, the modelled waveforms show an encouraging correspondence with some measured waveforms. This gave confidence that the model could be used to examine wave propagation around the tunnel, and allowed a scaled source to be developed for forward analysis of the main experiment.

Jan 1, 2001

By V. V. Nazimko

Abandoned coal mines cause subsidence and structural damages. Shallow abandoned mines induce the most severe and harmful damages. In addition, they produce time-dependent subsidence which is difficult to predict. Backfilling of underground cavities with waste materials have been used to prevent the time-dependent subsidence or to mitigate its effect. However, this procedure is expensive. A new drill and blast technique has recently been proposed to prevent surface damage from time¬dependent subsidence over abandoned mines. It utilizes the principle that blasting in the caved rock and roof in the vicinity of a cavity will dilate the ground and create a self-supporting effect owing to increase in the volume. Physical modeling has demonstrated that artificial dilation of caved rock using the drill & blast technique creates positive effects due to the following sequence of events: the dilated rock creates a supporting effect for the suspended rock strata and reduces its span which decelerates 3.4 times the process of caving. The roof span is reduced by the next caved layer, which causes the hole boundaries to incline to each other. This effect converts the process of caving from a developing mode to a reduction mode. Finally, the sinkhole zone assumes a triangular shape with a negative angle of draw 64-700 in contrast to a rectangular shape of the chimney zone for natural caving. Vertical dimension of the triangular zone is 3.87 times of the room height. Final surface subsidence decreases at least 2.09 times; displacement 1.31 times, slope 2 27 times; curvature 3.42 times, horizontal strain 1 21 times in comparison to natural caving of the ground over an abandoned mine.

Jan 1, 1999

By D Vidyarthi

Blasting is the most important activity in the mining industry, the world over. It is a well known fact that only part of the explosive energy gets utilized in causing the actual rock fragmentation. The rest of it gets converted into blast-induced ground vibrations and noise. Though blast vibrations cannot be totally eliminated, it is possible to minimize them by optimization of blast parameters. This paper highlights various in-house efforts put forth by the author towards site specific blast optimization and the monitoring of blast vibrations. It also deals with the prediction curves developed by regular regression analysis for the prediction of ‘blast vibrations’, ‘peak particle velocity’, ‘safe charge’ for various blasts.

Jan 1, 2007

Ilmenite production in Western Australia commenced in 1956. There are now five producers, all in the Bunbury-Capel district, and current total production capacity is about 450,000 t.p.a.The deposits occur near the surface and average between 10 and 50 per cent heavy mineral. About 70-85 per cent of the heavy mineral is ilmenite. Other heavy minerals present include leucoxene, zircon, rutile, monazite, and garnet. The ilmenite contains 52-60 per cent Ti02. and is very low in chromium (0·03-0·04 per cent CrS03)Mining is done by sluicing, drag line excavation, or dredging. Primary concentration of the heavy minerals is achieved by spirals, revolving cones, or Reichert cones. After drying and screening, ilmenite is separated from the heavy mineral concentrate by various types of magnetic separator.Separate leucoxene, zircon, rutile, and monazite concentrates are also produced. Each plant uses a different technique and the processes used include chemical attritioning, screen plate electrostatic separation, high tension rolls, air tables, and dry launders.INTRODUCTIONThe treatment of beach sands in the Bunbury/Capel area for the extraction of ilmenite is a very recent development in the mining industry in Western Australia. Nevertheless, since the commencement of production in 1956, ilmenite has become the sixth most important mineral produced (Table 1).The increasing world recognition of Western Australia as a major producer of ilmenite (Table 2) is due primarily to the low chromic bxide content of the mineral (0' 03-0' 04 per cent Cr203), combined with a medium to high titanium dioxide content (54-60 per cent Ti02), supported by large reserves, a stable government, and close access to good shipping facilities. Ilmenite is. produced from these deposits at low cost which enables the industry to compete on world markets despite high rates for sea freights because of the distance from major markets.

Jan 1, 1965

By W. E. Tournay

In accordance with a cooperative agreement between the Bureau of Mines, United States Department of the Interior, and the Linde Air Products Co., an investigation was made at the Bureau Explosives Testing Station, Bruceton, Pa., to develop suitable test methods for evaluating the performance and sensitivity characteristics of liquid-oxygen explosives. This report presents the results of the investigation. The unique nature of liquid-oxygen explosives necessitated both modification of standard techniques and development of entirely new test methods. The latter requirement was due to the fact that differences exist in the kind of information that must be developed for studying relative safety and performance properties of these explosives compared to that of fixed explosives.

Jan 1, 1949

By J Lombardi, M Weidenbach

"OZ MineralsÆ Prominent Hill copper-gold concentrator is located 650 km north-east of Adelaide, 130 km north-east of BHP BillitonÆs Olympic Dam operation and 130 km south-east of the regional township of Coober Pedy, in the Gawler Craton region of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a 10 Mt/a ore throughput capacity, operating well over the design rate of 8 Mt/a. Increased throughput rates have seen a decreased water recovery from the tailing thickener due to operating above design. Subsequently, greater pressure was placed on the site water balance and bore field off-take rates due to increased evaporation losses from greater volumes of water reporting to the tailing storage facility. This resulted in a trade-off between water availability and milling rates as part of the operating strategy.Two projects were implemented to increase the tailing thickener underflow density, thus improving water recovery directly back into the operating plant, reducing water losses via evaporation and decreasing the reliance on the bore field system operating at maximum rates to maintain mill throughput. The two projects were: tailing thickener feedwell redesign implementation of the Manta Cube control system.This paper discusses the background, implementation and benefits attained from these two key projects. Combined they have allowed a two to three per cent increase in tailing thickener underflow density to be consistently achieved, which has allowed greater water recovery. As a result, the processing plant has been able to operate at higher throughput rates when required, with greater water availability in the process plant recirculating system and a reduction in occurrences of the plant being æslowed downÆ due to water supply shortfalls. Both projects have also delivered a significant reduction in flocculant usage.CITATION:Weidenbach, M and Lombardi, J, 2012. Tailing thickener operability and control improvements at Prominent Hill, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 137-142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 29, 2012

By P. J. van der Walt

Some 30 years ago exposure to dense-medium separation in South Africa, culminated in the adaptation of the process for the treatment of -0.5 mm fines. The first commercial plant at Greenside Colliery apparently operated for some 18 years. Three further plants followed, including one treating tin ore. It is gratifying to learn, therefore, that there is renewed interest. The objective of making the process easier to operate (?more practical??) is commendable but the cumbersome technical approach could be counter productive. Perhaps a brief outline of the original thinking might be helpful when analysing the problem.

Jan 1, 2003

By R. Ressel

Keywords: ferrovanadium, thermodynamics, phosphorus Recyclable material is rapidly gaining in importance as a source of raw materials in industrialized countries. This is also the case in the production of ferrovanadium, where, increasingly, materials such as discarded capacitors, spent catalysts, slag, dust and sludge are used. As the V-content in the raw material varies greatly, the demands on process technology are very high. The share of perturbing elements depends very much on the source of the raw materials, which, in turn, makes a corresponding optimization of the various refining steps necessary. The raw materials are mostly available as oxides, which means that carbon, silicon or aluminium are used as reducing agents. Thermodynamic calculations were used to show especially the behavior of vanadium and phosphorus at different process conditions.

Jan 1, 2005

Excavations in rock are commonly supported with wire mesh, shotcrete, wire mesh and shotcrete in combination, and shotcrete reinforced with various types of fibres. Wire rope lacing and various types of straps are additional forms of support installed over the above types, to cope with severe conditions. These support systems are very important items of ?membrane? rock support. With the recent development of several types of thin sprayed linings, the importance of membrane support is likely to increase in the future. In this paper, a wide range of mechanisms of membrane behaviour and mechanisms of loading of membranes, is described. The concepts of membrane components, which are single membranes that may be used on their own as rock support, and membrane systems, which are combinations of more than one membrane component, are introduced. Different situations have different requirements of membrane support, and differences between civil engineering and mining requirements are highlighted. With the different basic requirements in these two areas, the requirements of rock support are correspondingly different. A thorough understanding of the mechanisms of behaviour of the different types of membranes, and the different mechanisms by which the membranes are loaded, is essential before a selection of appropriate support can be made, before appropriate design methods and calculations can be determined, and before appropriate performance test methods for membranes can be defined. The material in this paper contributes towards the understanding of membrane support behaviour.

Jan 1, 2001

Jan 1, 1998

By Clarence Hall, Spencer P. Howell

Among the more important factors involved in the use of high explosives in blasting operations is the means employed to bring about the detonation of the charge. When flame is applied to high explosives many of them may burn if not confined; but all of them when burning under certain conditions of confinement may detonate. Detonation may also be effected by mechanical means, such as frictional impact caused by a blow or by rubbing between surfaces. By this means, however, the full effect of the explosive charge may not be developed, so that a partial detonation, often accompanied by the burning of the explosive, results. When nitroglycerin was first used it was fired by the application of flame, but considerable difficulty was experienced in exploding it with certainty and in obtaining uniform resl'llts. In 1864 Allred Noble, a Swedish engineer, discovered that nitroglycerin could be surely and completely detonated by exploding in contact with it a small quantity of an initiatory explosive. Mercury fulminate was the substance then found capable of producing the best results There are many other fulminates and other substances that will produce complete detonation of commercial" high" explosives, but detonators or electric detonators containing mercury fulminate as the characteristic ingredient are still almost exclusively used in this country. The term" detonator" is used in the publications of the Bureau of Mines to designate what the miner calls a "blasting cap "-a copper capsule containing a small quantity of some detonating compound that is ignited by a fuse. The term" electric detonator" is applied to a blasting cap that is similar except for being ignited by means of a small wire which is heated to incandescence or fused by the passage of an electric current. One of the conditions prescribed by the Bureau of Mines for a permissible explosive a is that it shall be :fired by a detonator, or preferably an electric detonator, having a charge equivalent to that of the standard detonator used at the Pittsburgh testing station. A further requirement is that this charge shall consist by weight of 90 parts of mercury fulminate and 10 parts of potassium chlorate (or their equivalents). At the request of a manufacturer of permissible explosives, an investigation was undertaken by the bureau to determine the relative strength of detonators and electric detonators having different compositions. The tests of electric detonators herein reported were conducted by H. F. Braddock, junior chemist; J. W. Koster, J. E. Tiffany, junior mining engineers; and A. S. Crossfield, junior explosives chemist, at the Pittsburgh testing station of the bureau. Similar tests of detonators were not conducted because it was believed that the results would not show sufficient variation to warrant such tests. It is hoped that the conclusions drawn from the tests made will be of service to those using explosives by enabling them to select the grade of detonator or electric detonator that will insure the most effective results. The conclusions are given in this bulletin, which is published by the Bureau of Mines as one of a series of publications dealing with the testing of explosives and the precautions that should be taken to increase safety and efficiency in the use of explosives in mining operations. The results of tho experiments described in this bulletin show that the average percentage of failures of explosives to detonate was increased more than 20 per cent when the lower grades of electric detonators were used instead of No. 6 electric detonators, and was increased more than 50 per cent when these lower grades were used instead of No. 8 electric detonators. It is noteworthy, however, that when sensitive explosives, such as 40 per cent strength ammonia dynamite (p. 33), were tested under conditions ideal for detonation, the same energy was developed irrespective of the electric detonator used. When tests were made with a less sensitive explosive, such as a 40 per cent strength ammonia dynamite containing nitrosubstitution compounds (p. 32), the energy developed increased with the grade of the electric detonator used. For example, the average efficiency of four different explosives was increased 10.4 per cent when a No.6 electric detonator was used instead of a No.4 electric detonator, and 14.9 per cent when aN 0.8 electric detonator was used (see tabulation onp.45). The results of the tests emphasize the importance of using explosives in a fresh condition, but as fresh explosives can not always be had in mining work, strong detonators should be used in order to offset any deterioration of explosives from age.

Jan 1, 1913

By Qingwei Wang

This study focused on acidic wastewater from producing sulfuric acid system in zinc smelter containing mercury 21.48mg/L, zinc 55.85mg/L, lead 38.50mg/L, copper 1.68mg/L, cadmium 10.25mg/L, As 29.86mg/L treated by biologics. The factors of pH value, the ratio of biologics to mercury, complexing time, hydrolytic time and temperature were studied in this paper. Experimental results indicated that at pH value 10, quantity of biologics to mercury ratio was 16, complexing time 30min, hydrolyzation time 20min, temperature at 40?, concentration of mercury in treated water was removed to 22.15µg/L. At same time heavy metals such as Zn, Pb, Cu, Cd, As was removed by biologics, the remained concentration in treated water was Zn 0.53mg/L, Pb 0.12mg/L, Cu 0.01mg/L, Cd low to 0.01mg/L and As 0.023mg/L. According to EDAX analysis, mercury content in complexing sediment reached 28.49% easily to recycle as raw material and low concentration of heavy metals in hydrolytic sediment easily to dispose and treat.

Jan 1, 2009

A BRIEF DESCRIPTION OF TELPHER HANDLING AND BLAST FURNACE EQUIPMENT.The various sections will be described in the following order:(a) Telpher Handling and Storage Bins.(b) Blast Furnaces.(c) Slag Disposal.(d) Bullion Handling to Drossing Kettles.(e) Copper Drossing.(f) Copper Matte Furnace.(g) Bullion Delivery to Refinery.(h) Fume Handling.(a) TELPHER HANDLING.The telpher installation is an all-steel structure designed to carry out the work of assembly and delivery of charge materials to the blast furnaces.To simplify description, the primary telpher installation will be divided into three (3) sections:-No. 1 Section. 395 ft. long, running north and south, parallel to the water front, and so located that coke, which...

Jan 1, 1937

By K A. Bunker, A D. Campbell, E Ah Mu, A R. Penney

The Ernest Henry mine is a transverse sublevel cave (SLC), which is relatively unique due to the 45 degree inclination of the orebody. To economically recover ore, each sublevel is horizontally offset from the previous level by around 25 m, depending on the orebody geometry. Mine development, slotting and initial production within this zone occurs in a high stress abutment that increases in magnitude at depth. These areas are seismically active and close to the hanging wall where cave propagation is yet to initiate. High stress conditions and the close proximity to the cave seismogenic zone results in challenging geotechnical conditions in the step out zone of each level and requires management of hazards including stress driven rockfalls, rock bursts and pillar failure.This paper outlines how these hazards were forecast using numerical modelling and geotechnical monitoring. Risk management techniques included dynamic ground support design, development of a new mine layout and extraction sequence as well as delayed re-entry into seismically active areas. Ongoing monitoring, instrumentation measurements and field observations were used to track the effectiveness of the controls.Future production levels are forecast to experience increasing stress and seismicity, which will increase demand on excavations and installed ground support. Ensuring the techniques and controls for monitoring, measuring and mitigating stress and seismic hazards are enforced is essential for continued safe production.CITATION:Campbell, A D, Bunker, K A, Ah Mu, E and Penney, A R, 2016. Managing stress and seismicity in an inclined sublevel cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 319–328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By L. R. Stace

Arguably, one of the most significant technological breakthroughs that had been experienced during the period when British Coal was the major coalmine operating company in the UK, the use of rockbolts as principal support in underground roadways brought with it the need to re-assess the technical knowledge, management controls and legislative frameworks associated with the support of mine workings. Following a major roof fall in a roadway supported principally using rockbolts in which fatalities occurred, the process of the design of rockbolted support and the systems and procedures that had been put in place to control its use in the UK were further reviewed. The paper discusses the outcome of these reviews, and how the incident initiated a major new interest in strata control research in the UK against the background of the fragmentation of the ownership of the mines following the sale of the former British Coal assets at the end of 1994, together with the proposed introduction of new strata control legislation in 1996.

Jan 1, 1996

By George A. Morgan

Output of minerals was insignificant in 1981 and made a negligible contribution to the gross national product (GNP), estimated at $1.2 billion.2 Agriculture accounted for 40% of CNP and manufacturing accounted for 10%. The chief source of income was indirect taxes levied on traffic through the Port of Cotonou, an entrepôt. Trade statistics for Benin were incomplete and dated. Major trading partners were France and other members of the European Communities. Benin was a member of the West African Monetary Union and as such must coordinate its foreign currency, reserves, interest rate structure, and fund transfer with other member countries. Its currency, the Communauté Financière Africaine franc (CFAF), was fixed to the French franc.

Jan 1, 1983

By B McCarthy

Mining has been typified of late as a boom and bust, cyclical industry operating against a steady decline in the size and quality of mineral deposits. Decreasing deposit grades and increasing costs of traditional mining techniques, all in the face of another commodity downturn, are forcing mining companies more than ever before to seek out new and innovative ways to operate. New technologies are emerging to model, control and track resources through the mining value chain, to move material about mines more efficiently, and to identify and separate ore from gangue early in the extraction process.Discovering such technologies however is only the first challenge for mining companies. Actually implementing technological change successfully has proved to be an even bigger challenge. Like for many industries, fulfilling the promised benefits for the expense and timing envisioned, has not been easy when innovative technologies are introduced.Citing the author’s insights and experiences in a number of emerging technologies, this paper explores barriers to implementing technological change in the mining context. Key elements of a change management framework, first developed for implementing mine management systems, are described to give mining executives insight into how they and their organisations can succeed through technology-driven change.CITATION:McCarthy, B, 2016. Successfully implementing technology-driven change in the mining environment, in Proceedings International Mine Management Conference, pp 89-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

The difficulty of accurately sampling cyanide gold bullion for valuation is well known, and nothing new or original is claimed in presenting this paper, but it was thought that a record of differences in the composition of bullion bars found here may be of interest to others, and perhaps helpful to those who have to do with theevaluation of cyanide bullion. This investigation was made after reading Mr. Sydney W. Smith's interesting paper on the Liquidation in Molten Alloys.*A method was in use of boring each ingot in two places and mixing the two borings for the sample. More accurate values were obtained, however, when the bullion was sampled in a molten condition immediately before casting into the ingot; the sample being so taken as to preclude oxidation of base metals before solidification of the sample.In all, samples from 32 ingots were assayed, and comparisons made between the existing boring sample and the proposed dip sample. Assays were also made of two other portions of the borings from each ingot, and the results show that in the majority of cases the borings sample assays higher in gold than the dip sample of the same ingot.The largest ingot cast weighs approximately 920 troy ounces, and has the dimensions shown in the attached sketch (Fig. 1). Ingots are cast in 0.1. moulds i in. thick, smoked and heated.METHOD OF TAKING BORING SAMPLES OF BULLION BARSThe bar is cleaned from adhering slag and drilled in two places only, to a depth of i-in., one hole on the top near one end and the other in the bottom at the opposite end of the bar.

Jan 1, 1931

By J. H. Zietsman, M. W. Erwee, P. J. A. Bezuidenhout, Q. G. Reynolds

"Pyrometallurgical furnaces are tapped through tap-holes that are opened with drills and oxygen lances. The lance is often used on its own or as the last step of opening the tap-hole. Interaction of oxygen with molten material inside the tap-hole can occur, and is a phenomenon that is not well understood. As part of a study that focuses on the effect of lancing on flow inside and around the furnace tap-hole, a cold-model validation was done. The validation study focuses on validating the MULTIPHASEINTERFOAM multiphase flow solver in OpenFOAM® for the problem involved. The sensitivity of the model to different materials properties (viscosity and density in particular) is presented with both cold models and the results from flow simulations in OpenFOAM®. IntroductionMany pyrometallurgical operations are carried out in furnaces where molten material accumulates continuously. Once enough material has accumulated and is ready to be removed from the furnace, material is tapped through one or more tap-holes in the furnace. Tap-holes differ significantly in both geometry and materials of construction, depending on the process involved – examples of different types of tap-hole configurations can be found in, for example, Nelson and Hundermark (2014). Tapholes all share one common feature: they are high, wear areas of the furnace. Molten material at high temperature flows through these areas, after which the tap-hole is sealed, usually using tap-hole clay. The purpose of the tap-hole clay is to harden inside the tap-hole and seal it until the next tap.Once ready to tap, a pneumatic drill and/or oxygen lance is used to open the tap-hole. The extent of lancing a furnace tap-hole depends strongly on the type of furnace. In, for example, many blast furnace operations lancing is limited as much as possible, and done only if drilling was not effective. In other operations, such as on small-scale pilot furnaces with short tap-holes, only lancing is used to open the tap-hole."

Jun 1, 2019

By A. C. Fieldner

This report is the fourth of a series of annual summaries of research and technologic work on coal by the Technologic Branch of the Bureau of Mines. The coal research program of the Bureau has been broadened and made more flexible to adapt it to changing conditions and needs of the coal industry, and as a result information as to the properties and composition of coal has been increased and new and improved practices in mining, preparation, and utilization of coal have been devised. The present

Jan 1, 1940