Search Documents

By Jennifer Riefenberg

Ground control hazards, coal quality, ore reserve estimation, and pollution modeling seem unrelated topics from most mining perspectives. However, geostatistical methods can be used to characterize each of these, and more topics. Exploratory drill core data, and continued drilling and field measurements, can provide a wealth of information related to each of the above areas and are often severely underutilized. Recent studies have led to the development of the Multiple Parameter Mapping (MPM) technology, which utilizes geostatistics and other numerical modeling methods, to generate a "hazard index" map, often from exploratory drill core data. This mapping has been presented for ground control hazards relating roof quality, floor quality, numerically modelled stresses due to mining geometry, and geologic features. A review of the MPM method, future directions with the MPM, and a discussion of using these and other geostatistical methods to quantify coal quality, ore reserve estimation, and pollutant modeling are presented in this paper.

Jan 1, 1996

By Xiao Min You, D. R. Swonbourne

Smelting of Cu anode slimes involves the use of a slag to hold the oxidised Cu, but some Ag is also inevitably oxidised to the slag. The solubility of Ag in sodium silicate slags at 1 100 and 1 150 degrees C has now been determined over a very wide range of oxygen partial pressures. Silver was found to be present in the slags both as neutral atoms and as AgO(0.5). The activity coefficient for atomic Ag was a very strong function of slag composition and temperature, whereas that for AgO(0.5) was much less affected by slag composition and was almost independent of temperature over the limited range examined. The results reveal that the dissolved Ag cannot be fully recovered by reduction of the slag with very reducing gases

Jun 21, 1905

By A. S. Macfarlane

The introduction of new technology into mining operations is seen as a strategic necessity by many mining companies, in order to improve safety and to improve operational effectiveness. Many attempts have been made in recent years to introduce new technologies into mining operations in southern Africa. Amongst these are noteworthy successes, as well as some disappointing failures. Often, the reason for failure does not lie with the technology itself, but with the work system into which the technology is introduced. Such failures may come with a significant opportunity cost, and have a detrimental effect on future development, simply because the system has not been adequately engineered, and the risks have not been adequately assessed and managed. This paper examines the reasons for such failures, and proposes a methodology to be followed to ensure successful and sustainable implementation of new technologies, such as to reduce technical and financial risk to the company, and to energize the workforce into ensuring the initial objectives of the project are met. The paper also focuses on the application of appropriate technology, and the development of technological applications which are commensurate with the level of development of the work environment into which it is introduced. The paper therefore focuses on the application of risk management, change management, systems engineering and feasibility analysis as being key elements of a successful and holistic technology implementation programme.

Jan 1, 2001

By E. D. Gardner

This is one of a series of papers describing mining and related subjects affecting mining in western mining districts and mineralized areas. The parts of this paper pertaining to current production, mining and milling methods and practices, and general conditions affecting mining were collected principally during a field survey made in May 1935. Some original data obtained on previous visits to the area are also included. The history, geological background, and past production of the mines and district are largely abstracted from previous publications, for which due credit is given later in the test. The principal districts in the Black Mountains are the Oatman or San Francisco and the Union Pass or Katherine. This range contains the principal producing mines of the State, in which gold is the only important metal. Although the total production of gold is relatively small as compared to other districts where the precious metals are obtained as a by-product in copper min¬ing, the area is one of considerable economic importance to the State.

Jan 1, 1936

By M. P. Brungs, S. Haji Amini

Static dissolution of CaO into a CaO-SiO2-Al2O3slag and slags with additional fluxing agents (fluorspar, nepheline syenite and ilmenite) was studied. The slag was packed into dense CaO crucibles and heated to 1500ºC /1600ºC. After reaction, the crucible was air cooled and cross-sectioned. The development of the Ca2SiO4 phase and concentration profiles of various cations across the reaction zone were examined by Electron Probe Micro Analysis. At 1500ºC, a Ca2SiO4layer was found to form at the CaO/slag interface. No such layer was evident at 1600ºC. Ilmenite and nepheline syenite were found to be effective substitutes for fluorspar, increasing the rate of CaO dissolution.

Jan 1, 2004

By Paul Hewitt, Tim Smirnoff

Design and construction of the Epping to Chatswood Rail Line tunnels in Sydney, Australia required an innovative approach to define hydrogeological properties of the Sydney Hawkesbury Sandstone and provided an insight into the hydraulic behaviour of fractured sedimentary rocks. To meet restrictive water inflow and infiltration criteria both the pre-treatment of zones of fractured or highly jointed rock, and waterproofing using an interior spray on membrane for the finished drained tunnels and stations was required. Methods typically used to address the interaction of groundwater and tunnels in the Sydney Basin are demonstrated by case histories from major design-build tunnel projects.

Jan 1, 2005

Being a geologist I intend describing the renaissance of the gold industry in Australia within its geologic framework; there is a geological pattern to the numerous gold projects which have been brought on stream over the past decade. We are now about midway through our third and largest gold boom which, at a peak of 7.5 million ounces is about twice the production peaks achieved in the preceding booms. From discovery in 1851 through 1870 we saw the first boom largely based on alluvial production in NSW and in Victoria at the great Ballarat and Bendigo Goldfields. The discovery of the Golden Mile in Kalgoorlie, Western Australia, underpinned the second gold boom in the period 1895 - 1915. On that basis the present boom should last through the next decade.   It has been a golden decade for Australian gold production. From less than ten mines in 1980 with production over 10 000 ounces and the largest, Telfer, with output of about 130 000 ounces we now find over 130 deposits being worked around the country today that produce over 10 000 ounces with the largest, Boddington, having an output of over 400 000 ounces. In total these mines produced an estimated 210 tonnes of gold in 1989 and we expect this year, 1990, that a new record production of between 240 and 250 tonnes will be set. This positions Australia in third place in the Western World behind South Africa #1 and the USA #2 and fourth in the world with the Russians holding second place overall behind the South Africans.

Jan 1, 1990

By Ned Baker

This report describes the development, construction and testing of a hydrogen-fueled underground mining vehicle. A hydrogen burning engine and a hydride fuel system, both previously developed, were installed on a modified utility vehicle, together with the necessary controls. In tests and in actual use, the vehicle performance in terms of speed, acceleration, and gradeability exceeded that of the standard, unmodified vehicle.

Jan 1, 1985

By Spooner H. W

The paper describes the search for mineral deposits in an area of 4,500 sq. miles of south-west Tasmania. The area is one of difficult access and the problem of speedy movement and maintenance of field parties was solved by the use of helicopters. The programme has followed a systematic pattern of the aerial photography of the exploration area with the preparation of photQmosaics and topographical base sheets from these mosaics. Geological maps were initially prepared by photogeological interpretation and making use where possible of pre-existing information. The maps produced were later checked by ground traverses. Geophysical maps were obtained by the use of airborne magnetic, electromagnetic and radiometric methods. Geophysical and geological anomalies were checked on the ground by a campaign using ground geophysical equipment in the former case and geological and geochemical work in both instances. Audio Frequency Magnetic and Induced Polarization techniques were used in an area which was covered by several hundred feet of Tertiary sediments.The campaign has reached the stage of the drilling of specific targets.INTRODUCTIONThis paper describes the activities of Lyell-E.Z. Explorations (L.E.E.), an organization which was formed in 1956 by the Mt. Lyell Mining and Railway Co. Ltd. and the Electrolytic Zinc Co. of Australasia Ltd. to explore for mineral deposits in an area of approximately 4,500 sq. miles in southwest and southern Tasmania. To provide the necessary personnel and equipment for this project the exploration resources of both Companies were pooled and augmented and a headquarters was established in Queenstown. The work was directed by a Committee of four made up of officials from both Companies; a review of this structure has recently been presented by Hall (1959).

Jan 1, 1960

By W. H. Van Niekerk

The metal zinc has been around since only about 1400 AD. This may sound like a long time, but when compared to fellow base metals copper and lead, which were discovered in 5000 and 4000 BC respectively, it is evident that zinc is a fairly new kid on the block. This may also be the reason why many new facts and benefits of zinc are still being discovered. For instance, it has been discovered only in the last few decades that virtually no life on earth is possible without zinc. In this address it will be shown that zinc is not only very useful to mankind, but is in fact vitally important for all forms of life. It will be shown that zinc is natural, zinc is essential for life, zinc protects, zinc contributes to the well-being of society and that zinc is fully recyclable. It is therefore hoped, that by the end of this address, zinc will no longer be viewed only as the metal that is responsible for the nice colour of roofing sheets and steel buckets, but may indeed be man?s best friend.

Jan 1, 2005

By A. C. T. Bigg, Y. Kocak, N. K. Bodur

The Gumuskoy silver mine, owned by the Etibank, in the province of Kutahya, Turkey, has been operating since 1987 with primary, secondary and tertiary crushers, and two parallel single stage ball mill circuits. Continuing problems with crushing and feeding of the ore to the ball mills, because of the moisture retaining and sticky nature of the ore, prompted an investigation into the possibility of converting the grinding circuit to an autogenous or semiautogenous grinding circuit. This would remove the bottleneck associated with the secondary and tertiary crushing. At the same time the target feedrate is to be raised from 140 t/h to 175 t/h. This paper demonstrates the response of five ore types, and blends of ore types in an onsite pilot plant test program, and also suggests how the variations can be handled in a SAG mill/ball mill circuit incorporating just one of the present ball mills.

Jan 1, 2000

By Y R Fu, D R. Xu, C J. Wu, G C. Hu, H Chen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Hainan Province (Hainan Island) in South China hosts numerous Mo-polymetallic ore deposits that are genetically related to Cretaceous granitoid intrusions. Laser ablation inductively coupled mass spectrometry (LA-ICP-MS) zircon U-Pb dating and molybdenite Re-Os dating reveal three metallogenic episodes: the late Early Cretaceous (ca 112 Ma), the late Early to Late Cretaceous (ca 95–106 Ma) and the Late Cretaceous (ca 72–89 Ma). The third mineralising episode might represent the youngest Mo mineralising event in East China. Results from this study demonstrate that Mo mineralisation on Hainan Island occurred under an extensional setting that was prevailing in the late Mesozoic (ca 180–67 Ma) in South China, which was likely due to the slab rollback of the subducted palaeo-Pacific plate beneath the South China continent.CITATION:Xu, D R, Hu, G C, Wu, C J, Fu, Y R and Chen, H, 2015. Geology and geochronology of the Mo-polymetallic ore deposits in Hainan Island, South China, in Proceedings PACRIM 2015 Congress, pp 645–648 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Lee R. Kump, Sarma V. Pisupati, Peter L. Rozelle, Alan R. Larson, Timothy S. White, Nicholas A. Crescenzo, Maureen D. Feineman

The Mercer Clay bed in central Pennsylvania has produced feedstocks for the refractory industry in the USA and has also been investigated as a source of alumina and lithium. Developments in global markets for these commodities, as well as rare earth elements, have led to their classification as critical minerals in the USA, in turn renewing production opportunities for the Mercer Clay resource. The work reported here includes a review of the clay types and minerals involved, as well as past mineral processing and extractive metallurgy test work, and reports new research results from renewed investigation of the deposit as a polymetallic resource. This renewed work has found lithium contents that exceed 1,000 ppm, lying directly below the overlying Mercer coal, where the alumina content ranged from 32 to 34 wt%. Total rare earth concentrations were somewhat lower than have been found elsewhere in the region, and the highest contents were also found to be stratigraphically close to the coal. Further work is required to establish the mineral hosts for lithium and rare earths and to define the extent of enriched alumina, lithium, and rare earth concentrations.

Jul 22, 2021

By Hennessy F. L

IntroductionEvolution of the Present SmelterRoastingFiringHearth SlopeDust HandlingFurnace DetailsSmeltingFurnaceFeed DeliveryPulverised Coal FiringWaste Heat BoilersDust HandlingAir PreheaterReverberatory Slag DisposalConvertingVesselsAir SupplyMatte TappingConverter Slag HandlingPurchased Ore PlantINTRODUCTIONSmelting in blast furnaces commenced at Mount Morgan in 1906, when copper, which interfered with gold recovery by chlorination, became an asset. After various changes in blast furnace practice, reverberatory smelting com...

Jan 1, 1952

By A-A Latscha, C Boyle

Geological modelling has historically been done using sectional interpretation of paper sections or on a computer screen. Boundaries of geological units or grade shells are interpreted by a geologist section by section and the shapes are drawn onto paper to be digitised later or they are directly digitised into a computer. This approach is referred to as explicit modelling. Such methods are time consuming if there are many section lines or boundaries to be interpreted. The number of metres drilled and resource models made is increasing each year and it will be difficult to keep up using explicit modelling methods. Alternatively, it is possible to use information carried in the drill holes, known geological relationships and point estimation methods in two or three dimensions, to create similar geology boundaries, while eliminating or at least greatly reducing the need to manually interpret and digitise detailed sectional interpretations. Such methods are referred to as implicit modelling and are available in a number of software packages. Implicit modelling approaches have been used in iron ore and found to significantly reduce the time needed for modelling while producing results that are comparable or better than standard explicit modelling approaches. A number of case studies have been undertaken of implicit modelling in iron ore deposits. Stratigraphic surfaces of bedded, folded and faulted iron ore deposits have been modelled in various deposits by Leapfrog Geo, GOCAD (with SKUA) and Vulcan Integrated Stratigraphic Modelling. Leapfrog Mining was used to model iron grade shells at particular cut-off grades. The modelled surfaces are of a high standard equivalent to those that could be produced by traditional explicit modelling but the time required by the implicit methods is far less. Implicit geological modelling is an active area of software development and improvements in software are likely.CITATION:Boyle, C and Latscha, A-A, 2013. Implicit geological modelling of iron ore deposits, in Proceedings Iron Ore 2013 , pp 57-66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Creasey J. W, Huntington J. F

Faults cutting the Lithgow and Katoomba seams in some collieries of the Western Coalfield can be classified, on the basis of spatial pattern, into three principal groups: meridional swarms of closely spaced minor faults and associated joints, with throws of less than 0.5 m and with exceptional faults of up to 5 m; isolated interswarm strike-slip faults in the Lithgow seam and widely spaced strike-slip faults in swarms in the Katoomba seam; and low-angle normal faults associated with the Lidsdale-Lithgow seam split.Orientations of faults and coal cleats in the coalfield are presented on stereoplots and histograms, as a basis for an analysis of fault dynamics. The low-angle normal faults were found to have been formed only along the Lidsdale-Lithgow seam split, and before the high-angle faults. The origin of the high-angle normal faults in the meridional swarms is discussed and it is suggested that basementcover interactions must have occurred. This suggestion is supported by geophysical evidence. Low-amplitude monoclines in the coal seam, and the spacing of swarms 0.9 to 4.5 km apart, may be due to the underlying basement structure.It is clear that postextensional compressive deformation of swarms in the coalfield gave rise to shortening by minor thrust development, and probably also caused the synchronous strike-slip movement on pre-existing normal faults. There is evidence to show that isolated interswarm strike-slip faults in the Lithgow seam, and widely spaced strike-slip faults in the Katoomba seam, may have originated synchronously with such thrusts. The axis of maximum principal compression ('71) for the thrust event was inferred to be near horizontal and aligned approximately E-W. Recent rock mechanics measurements of the present day stress field indicate a similar stress configuration.

Jan 1, 1981

By T. G. Paradis, C. A. Mohns

"This paper summarizes the Wren CAT (Clarifier and Accelerated Thickener) deep bed thickener operation at the EKATITM Diamond Mine in Canada’s Northwest Territories. EKATITMs’ thickener project is presented in terms of initial design considerations and present day operating practices. A circuit description summarizes process equipment, reagent systems, and typical process conditions, and details of Wren CAT operating principles are provided. Operating strategies are discussed, with emphasis on process instrumentation and control and operating challenges.INTRODUCTIONThe EKATITM diamond mine, operated by BHP Diamonds, Inc., is located in the Northwest Territories near Lac De Gras, approximately 300 km NNE of Yellowknife, NT. 9000 dry metric tonnes of diamond-bearing kimberlite ore are processed daily. Processing operations commenced in October, 1998.The EKATITM process plant flowsheet features typical steps in diamond recovery plant design. Figure 1 shows the general plant flowsheet. Size reduction and feed preparation are accomplished by crushing, scrubbing, and high pressure grinding rolls (HPGR) through closed-circuit classification with vibratory screens. Heavy medium separation (HMS) is used as the initial stage of heavy mineral concentration. Secondary concentration is accomplished in the recovery plant by attrition milling; wet, high-intensity magnetic separation (both wet and dry); and X-ray sorting.The present budget throughput rate is 9000 dry tonnes per day. This will be increased to 18,000 tonnes during the first ten years of operation. Unlike most kimberlite treatment facilities, which process material from a single ore body, EKATITM’s process plant was designed to accommodate ore from five different kimberlite pipes, each with its own treatment characteristics.All processing, except for primary crushing, is carried out in a temperature-controlled environment in the main process plant building."

Jan 1, 2000

Why A Friction Hoist? B EFORE discussing the equipment, it would be instructive to review the factors that influenced the management of Opemiska Cop-per Mines to purchase a friction hoist rather than a conventional double drum hoist. The mine required that 250 tons per hour be hoisted from a depth of 2,100 feet. They also specified that the top speed should not exceed 1800 feet per minute. Eight ton capacity skips in balance and a maxi-mum hoisting speed of 1725 feet per minute would meet the required <Output on a duty cycle as follows: Loading time Creep away from loading pocket Accelerate (at 2.5 ft/sec2) 10 seconds 5 seconds 11.5 seconds Full speed run Decelerate (at 2.5 ft/sec2) Creep into dump Cycle time Trips per hour Tons per hour 72 seconds 11.5 seconds 5 seconds 115 seconds 31 31x8 = 248

Jan 1, 1962

The ore treatment expansion programme at Mount Isa Mines required the erection of a new lead-zinc concentrator to be known as No. 2 Concentrator. This concentrator was designed by Western-Knapp Engineering Company in conjunction with staff of Mount Isa Mines Limited. Metallurgical design followed conventional wet milling practice, but the size of many plant units is larger than previously used at Mount Isa. The. total capacity of the new plant is 150,000 tons per four weekly period, and the plant is designed to operate in two equal parallel sections.Erection was contracted on a turnkey basis, and the plant was commissioned as a production unit on 23rd June 1966.The existing concentrator, No. I, was converted to treat all copper ore, and the total capacity of the two plants is now 390,000 tons per four weekly period.

Jan 1, 1968

By Alexander Filotti, Richard Kalson

"1. INTRODUCTION- WHAT IS P3 OR PPP ?The Public Private Partnership (PPP or 3P) is a project delivery scheme based on the government providing land and/or a concession agreement, and on a private entity providing the design, construction, financing, operation and maintenance of the project for an extensive duration of time (up to thirty years). At the end of the operation-maintenance period, the project is turned over to the public entity, which fully owns the project at all times. While there are many PPP delivery schemes used around the world, for the present paper, we are going to analyze the impact of the Design-Build-Finance-Operate-Maintain (DBFOM) scheme on the deep foundation specialty subcontractor. There are couple of reasons that the PPP delivery system started to be used and implemented not only by developed nations (e.g. United Kingdom, USA etc.), but also by the International Development Bank for delivering major infrastructure projects in developing nations. From the point of view of government agencies, some of the reasons to use PPP are the following:??The primary use of private capital in an era where borrowing and/or supplemental taxation represents too much of a political risk. Budget deficits and taxation limits are extremely hot topics in every election (national or local) and the level of education of the electorate in this area is making it more and more difficult for politicians to use borrowed funds and additional taxation finance sources for public projects. At the same time, we see an increase in the social expenditures of the government in parallel with a needed increase in expenditures on infrastructure due to aging and neglect.??Bundling the construction risks with the operational and maintenance risks naturally pushes the private entity to increase the level of innovation and communications in the primary phase ( the construction phase) in order to develop future process based upon the innovation and communications utilized in the operation and maintenance phase of the project. This is true if contractual incentives are properly structured because “all revolves around incentives. In a world of ‘incomplete’ contracts, where it is difficult to foresee and contract about uncertain future events, it is important to get the incentive structure right” (Grimsey and Lewis, 2004).??The transfer of very expensive risks such as differing site conditions, schedule, design, construction, maintenance and operation costs from the public authority to the private entity.??The timespan of development and construction of a PPP project is usually shorter than the traditional procurement process (e.g. “ the I-595 P3 provided capacity improvements fifteen years sooner than a conventional plan would have offered. In Maryland, an innovative expansion of the Seagirt Marine Terminal in the Port of Baltimore was completed two years ahead of schedule due to the P3 model. As a result, the Port of Baltimore is only the second port on the US East Coast to have unrestricted access to both a fully functioning 50-foot channel and 50-foot berth.”)"

Jan 1, 2017