Search Documents

By C. E. Baltzer

This is the fourth in a series of coal technology reviews being prepared. in accordance with a recommendation voted by the Coal Division C.I.M. in session at the Jubilee Meeting, Vancouver, 1948, that the Department of Mines and Resources be requested to arrange for publication by the proper Government authority of a Quarterly Review of Coal Technology for distribution among those concerned in the production and use of coal in Canada. Copies of the first review, which appeared in the November, 1948, BULLETIN, pp. 612-614, of the second review in the June, 1949, BULLETIN, pp. 272-275, and of the third review in April, 1950, BUL-LETIN, pp. 1,9?3-196 (also, respectively, in Transactions, Vol. LI, 1948, pp. 262-264 Vol. LU, 1949, pp. 117-120, and Vol: LIU, 1950, pp. 133-136), were distributed by the Dominion Coal Board and are still available on request. In this review, the first in the series in the field of combustion, development and trends during the period approximately from World War II to the present time are described and therefore the presentation is general. Later reviews will particularize developments in relation to the range of coals available in Canada.-ED. INTRODUCTION THE utilization of coal in heat and power producing equipment has become of paramount importance to the coal industry in maintaining stable and profitable markets. In the past, the chief concern was with mining, transportation, and overall supply problems, but modern conditions demand interest in and knowledge of all phases of the product, from coal in situ to its ultimate disappearance in the form of products of combustion. Even the last mentoined factor has caused complications, as is shown by current widespread activity in the field of smoke abatement

Jan 1, 1951

By P. G. Guest

MANY of the gases and vapors used in anesthesia form explosive mixtures with oxygen or air. Sources of ignition for these mixtures always have existed in operating and anesthetizing areas. When ether was first introduced, candles,5 gaslights, and coal stoves caused fires and mild explosions of the vapor-air mixtures. Today the chief causes of ignition are electrical. Fires and explosions are still much too frequent; and, because many of the mixtures are rich in oxygen, the explosions sometimes are very violent. Obvious sources of ignition, such as electric-power sparks and arcs in open motors, switches, and receptacles, as well as exposed incandescent wires and hot plates, usually are recognized by hospital personnel and corrected. A source of ignition that is not so obvious to many is static electricity. Until quite recently the presence of this hazard in a large majority of anesthetizing areas was not even suspected. However, numerous explosions-many of them fatal to patients-have been attributed, with good reason, to sparks from static electricity.

Jan 1, 1953

By Abraham Lindo

"Blasting plays a key role in hard rock underground mining. It is by nature a violent and destructiveextraction method designed to economically fragment the rock into a suitable size for it to be loaded and hauled as part of the specific mining process while controlling the amount of damage to the surrounding rock mass."

Jan 1, 2016

By K. Turgeon, J. -F. Boulanger, L. Whitty-Léveille, C. Bazin

"Several companies targeting Rare Earth Elements (REE) around the world have completed a Preliminary Economic Assessment showing positive project financial results. Although REE ores may contain high REE value, financing these projects remains difficult in part due to the number of processes required to valorize the elements and the relatively low yield of these processes. Direct ore leaching without the production of a concentrate may reduce the capital and some operating expenditures through process simplification, and increase revenues because of REE recovery improvement.A silicate REE ore is used to test various hypotheses regarding whole ore processing and to develop a simplified flowsheet. An atmospheric leach (200 kg/t H2SO4) of crushed whole-ore containing 0,6% REE, followed by impurity removal and REE precipitation recovers 80% of the REEs in a solution containing REE and Th. The high value contained in most REE deposits makes whole-ore approaches worth considering for most projects, given the losses of valuable species typically associated with the production of a REE mineral concentrate from the ore. INTRODUCTIONRare Earth Elements (REE) find applications in modern and clean technologies, whether civil, industrial or military. With China producing more than 90% of the world’s REE, the embargo imposed by this country in early 2010 increased REE prices for a three year period. With prices having shrunk back many-fold from their peak value, projects put forward during the hike are struggling to secure financing. Owing in part to unconventional processes such as acid-baking and solvent extraction, REE plants are high capital cost and high operating-cost units, and present technological risks (Verbaan et al., 2014)."

Jan 1, 2016

By Mei Long, Tawum Juvert Mbah, Jianhua Zhang, Haiwang Ye

There have been many improvements and advancements in the application of neural networks in the mining industry. In this study, two advanced deep learning neural networks called recurrent neural network (RNN) and autoregressive integrated moving average (ARIMA) were implemented in the simulation and prediction of limestone price variation. The RNN uses long shortterm memory layers (LSTM), dropout regularization, activation functions, mean square error (MSE), and the Adam optimizer to simulate the predictions. The LSTM stores previous data over time and uses it in simulating future prices based on defined parameters and algorithms. The ARIMA model is a statistical method that captures different time series based on the level, trend, and seasonality of the data. The auto ARIMA function searches for the best parameters that fit the model. Different layers and parameters are added to the model to simulate the price prediction. The performance of both network models is remarkable in terms of trend variability and factors affecting limestone price. The ARIMA model has an accuracy of 95.7% while RNN has an accuracy of 91.8%. This shows that the ARIMA model outperforms the RNN model. In addition, the time required to train the ARIMA is than that of the RNN. Predicting limestone prices may help both investors and industries in making economical and technical decisions, for example, when to invest, buy, sell, increase, and decrease production.

Jan 6, 2021

By Micah Nehring, MEHMET KIZIL, Farzad Sotoudeh, Amin Mousavi, PETER KNIGHTS

Production scheduling in underground mines is one of the most important and complex processes in maximising the economic value of an operation over the life of the mine. Due to increasing energy, transportation, processing and smelting costs and reducing water availability, the extraction of ore deposits through underground operations has become more expensive and challenging. A potential productive and efficient solution to mitigate these issues is to integrate pre-concentration systems into the existing mining system to increase ore grades through a preliminary process of rejecting some waste before sending the ore to the energy intensive mineral processing plant. Further benefit of such systems includes the utilisation of the waste and low-grade material in backfilling of open stopes to reduce the transportation costs and surface environmental impact such as reduction of CO2 emissions and waste transportation. The objective of this paper is to present a new mathematical model to optimise the production schedule of underground metalliferous mining operations in the presence of a pre-concentration system. The proposed model optimises the production schedule and sequencing of stopes within a sublevel stoping operation. The results of this study illustrate the potential economic benefits of using a pre-concentration system prior to a mineral processing operation as a result of increased net present value.

Nov 16, 2023

By I. Tinto

"IntroductionEnvironmental pollution problems, caused by gases or effluents, by high noise levels or from air borne dust, are placing increasing demands of the operators, from statutory authorities, and from the general public, to adopt more stringent dust control measures. This requires that a successful plant dust control program be an integral part of any plant operation. While a successful environmental program is a key factor in maintaining productivity and good labour relations, anticipation of future environmental regulations during the plant design phase can avoid the high cost of plant upgrading, or dealing with pulmonary conditions in the work force in subsequent years.Particulate removal, conventionally called dust collection, involves the removal of coarse- and fine-particulates from the airstream. Although generally limited to that required for contro!Hng plant generated air emissions, particulate control equipment also has a wide application for air cleaning and filtration inside the plant, as well as for recovery of usable products.In the late 1950s and early 1960s the public became more concerned with the problems of air pollution. This increasing concern was stirred by an awareness of the extremes to which water pollution had progressed in many of the rivers and lakes, by increasing perception of air pollution as detected by visible smog and harsh chemical odors, by the alarming rate of increase of smog plagued cities and communities, and by specific incidents where ill health could be traced to specific episodes of air pollution. Particle size is perhaps the most important single factor affecting particulate control. Large particles (over 5 microns) constitute the major mass fraction of most sources of emission and economical control equipment dqes exist for their efficient control. However, while these larger particles frequently represent the source of soiling and unsightly smoke plumes, they are not a major health problem as they tend to settle relatively quickly, are more easily scrubbed from the atmosphere by rain, and are not able to penetrate the respiratory system. By far the most important form of particulate air pollution is the fine particulate, (below 3 microns) which is harmful to the pulmonary system. The adverse effects caused by this particulate matter on human health are for the most part related to injury to the surfaces of the respiratory system. Particulate material in the respiratory tract may produce injury itself, or it may act in conjunction with gases, altering their sites or their modes of action. A combination of particulates and gases may produce an effect that is greater than the sum of the effects caused by either individually (i.e. synergistic effect)."

Jan 1, 1989

By R. W. Stahl

An award is a form of recognition given for superior performance in a special field of endeavor. Each year awards are given by the Joseph A. Holmes Safety Association and the National Safety Council to mineral industries' mines, quarries, and plants that have worked a specific number of man-hours without a lost-time injury. These awards have a dual significance in that they prove that efficiency can be attained without injury to persons. Safety awards do not result from luck or good fortune but do result from sincere desire coupled with sufficient effort and cooperation to achieve a desired goal.

Jan 1, 1963

By R. Perlman

This paper describes the various new computer-aided techniques being used by economists in the construction of economic models. It discusses the relevance of these techniques to mining industries. In particular, it describes their role in making it possible to obtain better estimates of future price and demand developments on the markets on which metals are sold, and how these estimates can be used to improve forward planning by mining companies.

Jan 1, 2014

The upper amphibolite-grade mctasediments of thc rinaroo area, North Queensland, form part of a regional aurcole to the large Tinaroo Batholith and are the stratigraphic equivalents of the Hodgkinson Formation of gencrally low metamorphic grade. There is no evidence of any lithological unconformity.The higher grade metasediments have a more complex deformation history than is typical for thc surrounding region and this may bc due to one or a combination of two factors; an additional strain componcnt associated wilh the intrusion of Ihe Tinaroo Batholith, or a more marked finite strain response to the overall regional stress field within hotter. more ductile rocks.Four deformational events can be characterized within Ihc Tinaroo Area. Close to Ihe Tinaroo Batholith D1 and D2, arc so strongly developed that they disrupl the continuily of Ihe original Iithological layering. In the aureole region, D1 is strongly overprinted and its original fabric intensity is obscured, but both D2 and D3 display a mappable decrease in intensity away from the granite margin. These three deformations occurred during Carboniferous or early Permian time. D4 is later and only patchily developed.The broad, moderate pressure metamorphic aureole surrounding the Tinaroo Batholith is a typical of the CairnsCooktown group of Permo-Carboniferous granitoids. which usually develop narrow, lower pressure contact aureoles. Two periods of metamorphism are distinguishable. The first reached peak temperatures somewhat greater than 520°C, the second temperatures around 620-630° C immediately adjacent to the granite contact.Several cale-silicate lenses containing scattered scheelite mineralization occur within the area. Scheelite appears to have crystallized at the same time as the cale-silicate minerals, its appearance coinciding with the intrusion of the Tinaroo Batholith. Unlike many "skarn-type" scheelite deposits, the scheelite-bearing cale-silicates are Fe-poor, with no positive correlation between total Fe and W.

Jan 1, 1982

By P G. Greenhill

The Wonawinta silver project near Cobar in NSW is under development by Cobar Consolidated Resources Limited (CCR). RMDSTEM Limited is part of the owner’s team for feasibility, design, engineering, construction and commissioning.With a 51Moz resource CCR is one of the largest pure silver players in Australia. A probable reserve of 14.3Moz has been defined for a mine life of approximately five years. The silver mineralization is contained in host rock composed of clays and oxidized limestone. The ore also contains on average 1.3% lead as cerussite, and other minerals. A simple circuit consisting of slurrying of the ore, gravity treatment of the coarse fraction to recover lead, silver extraction using CIL, elution and the Merrill Crowe silver recovery process, has been developed.The “value engineering” approach to this development pioneered over the past decade by RMDSTEM has meant that RMDSTEM has delivered the bankable feasibility study at a cost of $0.07 per resource ounce. It is highly cost effective making efficient use of shareholders funds as well as being very time efficient. This paper describes the application of the value engineering approach to the development of the Wonawinta project.

Aug 8, 2011

By Andrea Bernardes

Printed circuit boards (PCBs) of varying compositions have been converted by incineration and following melting into an environmental agreeable slag and a copper-nickel-tin alloy, containing the precious metals. The environmental compatibility of the slag was determined according to the German standard DIN 38414 - Part 4; pollutants' concentration in the lixiviates is smaller than the thresholds of drinking water (CE-Standards). Each experiment the charge were 500g scrap from PCBs and ca. 100g slag forming material. The products were a kind of mullite slag, poor on iron, which was recirculated, and an alloy containing up to 0.3% Gold. With a burner to the retort coal gas, the waste gas was burned without soot, and the produced mixed zinc-lead oxide containing silver was collected in the flue dust.

Jan 1, 1997

By M. Frenzel, D. Ebert, K. Bachmann, A. D. Renno, R. Möckel, J. Gutzmer, J. Krause

With the increasing demand for metalliferous and mineral raw materials and the consequent depletion of the global natural resource base, the possible utilization of secondary raw material sources is receiving more and more attention. In the present study, we present results from a detailed vanadium deportment study of three basic oxygen furnace slag (BOS) samples known to containing elevated bulk concentrations of vanadium. Complementary analytical methods that were used to quantify the abundance and composition of V-containing phases include SEM-based automated mineralogy, X-ray fluorescence analysis, and X-ray powder diffraction as well as electron probe microanalysis. The vanadium deportment was quantified using Monte-Carlo simulations of the data obtained from automated mineralogy and electron microprobe analysis. The total V concentrations identified by XRF are between 1.7 and 2.2 wt.% V. The most important hosts of vanadium are larnite-, brownmillerite- and portlandite-solid solutions. In two samples Ca carbonates also significantly contribute to the V deportment, while wuestite, lime, and native iron do not contribute significantly to the vanadium deportment. A thorough consistency check identifies considerable uncertainties in the density of the V-bearing phases as the most likely reason to explain remaining discrepancies between measured and calculated V values.

Oct 14, 2023

By David R. Morrey

During the past 50 years, significant research has been performed in the ecology and physiology of plants that colonize soils containing elevated concentrations of heavy metals. Similar work has also been performed on plants that are able to survive acidic and saline environments. Efforts have focused on the ecological analysis of plant communities that occur over a range of metalliferous mining wastes. Investigations have been performed on the mechanisms that allow selected varieties of plant species to survive in normally phytotoxic environments and on the potential applications of metal-tolerant varieties of plant species. The purpose is the remediation and reclamation of mining wastes and soils that contain unusually high concentrations of so-called heavy metals. Characteristics of some mineral wastes Metalliferous mining wastes present special environmental restoration problems because of their toxicity. Potential toxicities are mostly caused by residual metals derived from weathering of low-grade ore or the waste products of mineral processing. In cases where pyrite forms a part of the mining waste, acid generation by oxidation may exacerbate the toxicity problem by promoting heavy-metal mobilization in aqueous solution.

Jan 1, 1995

By Michael G. Zabetakis

THIS is a summary of the available limit of flammability, autoignition, and burning-rate data for more than 200 combustible gases and vapors in air and other oxidants, as well as of empirical rules and graphs that can be used to predict similar data for thousands of other combustibles under a variety of environmental conditions. Specific data are presented on the paraffinic, unsaturated, aromatic, and alicyclic hydrocarbons, alcohols, ethers, aldehydes, ketones, and sulfur compounds, and an assortment of fuels, fuel blends, hydraulic fluids, engine oils, and miscellaneous combustible gases and vapors.

Jan 1, 1965

By Tim O’Neil

Question: Looking forward, do we face a future in which energy markets, energy policy and energy conflicts threaten to preoccupy, if not dominate, our concerns over economic growth, national security and domestic tranquility? The answer is, we may indeed face such a future. Question: What oil resource is comparable in size to the reserves of Saudi Arabia and presents a tremendous opportunity? The answer, the oil sands in Alberta, Canada. Question: What is the largest mineral staking rush in North American history, still under way? It has so far led to the development of two large mines. The answer is the Point Lake diamond strike in Canada’s Northwest Territories. It led to the development of the Ekati and Diavik mines.

Jan 1, 2004

By J. H. H. Chamberlin

"In the Introduction the author briefly discusses the company history as it relates to the development of its contracts with the Japanese steel mills. The main part of the text describes how Coleman Collieries Limited approached the problem of mining coal profitably in thick, steeply inclined seams. For many years a basic room-andpillar system was worked by conventional methods. Main roadways were driven on strike across the mineable area. These roadways acted as haulage routes for coal, materials and men. Rooms were developed to the rise of the main haulage route by pairs of men using air-operated hand picks. As these rooms advanced the miners would lay and extend a sheetiron chute down which mined coal would gravitate to a controlled loading point, where it was loaded into trains of mine cars. Connecting roadways or ""OFFS"" were driven at predetermined intervals between adjacent rooms, forming pil1ars or blocks. Extraction of the blocks followed on a line conducive to good strata control some distance behind the developing rooms. A need for higher productivity, expansion of the operations and a scarcity of qualified miners resulted in the company deciding to mechanize its underground mines. Joy 6 CM continuous miners and 10 SC shuttle cars were selected as being machines that could reasonably negotiate the problems associated with the pitching seam. The equipment, nonetheless, has definite limitations and Coleman therefore developed a modified version of the room-and-pi11ar system such that the miners and cars could work on cross pitch. In the area described, main roadways were driven to the rise on an average gradient of 12 degrees. Panels, which consisted of two parallel roads with interconnecting cross-cuts, were then developed on strike to a boundary point. Blocks formed in the development of the panels were subsequently extracted on retreat. Problems associated with each phase of the operation are thoroughly discussed, together with roadway support methods and equipment used for the conveyance of coal and materials."

Jan 1, 1972

By M. Gangal

CANMET-MMSL, in cooperation with Dry Systems Technologies and Quinsam Mine, conducted a study to determine the effects of B50 biodiesel on the emissions of a flameproof diesel power package in comparison with mining diesel fuel for application in underground coal mines. The emissions testing for coal mine application requires that the intake air mixture to the engine should be at 1.25 percent methane by volume in air. The tested power package system included a naturally aspirated, mechanically-controlled diesel engine with a diesel oxidation catalyst (DOC), a heat exchanger, flame arresters, and a low temperature disposable diesel particulate filter. The engine dynamometer tests were conducted at the CANMET-MMSL Diesel Emissions Research Laboratory in Ottawa using the ISO 8178-C1 test protocol. The separate and combined effects of a B50 biodiesel blended fuel, and with and without 1.25% methane enriched intake air were measured on a diesel power package. Fuelling the baseline engine (without methane), with B50 biodiesel blend reduced carbon monoxide (CO) by 44%, and increased nitrogen dioxide (NO2) by 19%, and particulate matter by 31% relative to the mining diesel fuel. Similarly, injection of 1.25% methane to the intake air for baseline engine with mining diesel fuel increased engine power by 15%, CO by 124%, and NO by 15%, and decreased NO2 by 13%. The effect of B50 biodiesel relative to the mining diesel for coal mines application (with methane for both fuels) was to reduce CO by 27%, and NO by 6%, and increase NO2 by 23%, with no change in engine power. The overall results indicate that the minimum ventilation rate for the equipment application in coal mines with B50 biodiesel was 4.11 m3/s (8,700 cfm), slightly higher than the ventilation rate of 4.01 m3/s (8,500 cfm) with the mining diesel fuel. This slight increase in ventilation rate for B50 biodiesel fuel was due to an increase in NO2 at one of the operating test points, and the ventilation rate for this equipment was governed by NO2 in the exhaust gas.

Jan 1, 2009

By Don Peel

Mineral aggregate, the most widely used mineral resource globally, has attracted little academic or public interest. Of all mining developments, the aggregate resource is seldom factored into resource management decisions. This lack of recognition to the strategic aggregate resource has significant economic, environmental, and social implications. Impact to the economics, the environment, and the community coincide with the key elements of the United Nations concept of ?sustainable development?. To build on the concept, the mining sector contracted the International Institute for Environment and Development to assess how mining activity contributes to sustainability. As a result, a useful assessment process was developed by the Mining, Minerals and Sustainable Development (MMSD) Task Group entitled ?Seven Questions to Sustainability: How to Assess the Contribution of Mining and Mineral Activities.? In Alberta, recent opposition to mineral resource development by community residents offers an opportunity to employ the MMSD?s assessment procedure. The public opposition to the mining activity was addressed through a stakeholder planning process initiated by the municipal council of Sturgeon County, Alberta. As a result the Calahoo/Villeneuve Area Structure Plan (CASP) was formulated and adopted. To measure the effectiveness of the CASP planning process in terms of sustainability, this paper applies the MMSD?s Seven Question assessment to the Calahoo/Villeneuve Area Structure Plan.

May 1, 2004

By J. C. Escobedo, J. M. Almanza, A. Flores, Cortés. D. A.

Secondary aluminum dross, which has been exposed for several years to atmospheric conditions, was characterized using chemical analysis, X-ray diffraction, optical and scanning electronic microscopy, and energy-dispersive spectroscopy. Based on the characterization, a method to purify the solids is presented. This method starts with the washing of the dross in boiling water to eliminate the soluble compounds like Na and K, followed by the physical separation of the metallic aluminum by milling and screening. Finally, an acid lixiviation process is applied using three different acid solutions, HCl, HNO3, and H2SO4. The best results were obtained using HCl. The main insoluble components of the dross after lixiviation were Al, SiO2, and Al2O3. MgAl2O4, AlN, Si, and Na2Al22O3·2H20 species were also found. Based on the alumina content, the solid product could be suitable as a raw material in the manufacture of castable refractories or metal matrix composites.

Jan 1, 2005