Search Documents

Konkola No 3 shaft experienced severe mining-induced stress and time-related deterioration in ground conditions in an area where an over-cut and bench (OCB) mining method was used to extract a shallow dipping wide orebody. This caused an unacceptable risk for safe mining operations to sustain the required levels of production. After a review of the conditions it was decided to change the mining method to CASCADE to recover ore in the affected area and modify the OCB method and use a modified over-cut and bench method (MOCB) for new mining sections. This paper describes the geotechnical criteria included to derive the mining standards for the MOCB. The geotechnical risks are identified and taken into account to develop stope design parameters, stoping sequences and support requirements. A monitoring programme to assess conditions as mining progresses is also discussed.

Jan 1, 2005

By A J. Nick, I I. Townsend, J M. Schuler, J D. Smith, R P. Mueller, L Sibille, K Leucht, J J. Fox

The first steps for in situ resource utilisation (ISRU) on target bodies such as the Moon, Mars and near-Earth asteroids (NEA), and even comets, involve the same sequence of steps as in the terrestrial mining of resources. First exploration including prospecting must occur, and then the resource must be acquired through excavation methods if it is of value. Subsequently a load-haul-dump sequence of events occurs, followed by processing of the resource in an ISRU plant, to produce useful commodities.While these technologies and related supporting operations are mature in terrestrial applications, they will be different in space since the environment and indigenous materials are different than on Earth. In addition, the equipment must be highly automated, since for the majority of the production cycle time, there will be no humans present to assist or intervene. This space mining equipment must withstand a harsh environment which includes vacuum, radical temperature swing cycles, highly abrasive lofted dust, electrostatic effects, van der Waals forces effects, galactic cosmic radiation, solar particle events, high thermal gradients when spanning sunlight terminators, steep slopes into craters / lava tubes and cryogenic temperatures as low as 40 K in permanently shadowed regions. In addition the equipment must be tele-operated from Earth or a local base where the crew is sheltered. If the tele-operation occurs from Earth then significant communications latency effects mandate the use of autonomous control systems in the mining equipment. While this is an extremely challenging engineering design scenario, it is also an opportunity, since the technologies developed in this endeavour could be used in the next generations of terrestrial mining equipment, in order to mine deeper, safer, more economical and with a higher degree of flexibility. New space technologies could precipitate new mining solutions here on Earth.The NASA Kennedy Space Center (KSC) Swamp Works is an innovation environment and methodology, with associated laboratories that use lean development methods and creativity-enhancing processes to invent and develop new solutions for space exploration. This paper will discuss the Swamp Works approach to developing space mining and resource extraction systems and the vision of space development it serves. The ultimate goal of the Swamp Works is to expand human civilisation into the solar system via the use of local resources utilisation. By mining and using the local resources in situ, it is conceivable that one day the logistics supply train from Earth can be eliminated and Earth independence of a space-based community will be enabled.CITATION:Mueller, R P, Sibille, L, Leucht, K, Smith, J D, Townsend, I I, Nick, A J, Schuler, J M and Fox, J J, 2015. Swamp works – a new approach to develop space mining and resource extraction technologies at NASA’s Kennedy Space Center: prospecting, excavation, load, haul and dump for in situ resource utilisation, in Proceedings Third International Future Mining Conference, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Green P. F

Apatite Fission Track Analysis (AFTA) is a thermal history reconstruction tool that enables determination of magnitude and timing of maximum paleotemperature and paleo-geothermal gradient at the time of maximum paleotemperatures. From this information, the amount of section missing at major unconfornities can be estimated and incorporated into basin models. The Gippsland Basin has a number of distinct problems that can be tackled using AFTA. 1. The nature of the regional break between the Late Cretaceous-Tertiary Latrobe Group and the underlying Early Cretaceous Strzelecki Group. 2. The tectonic history of the basement flanking the basin and its effect on sediment composition. 3. The age of igneous activity in the basin, as typified by the widespread basaltic plugs and dykes intruding the outcropping Strzelecki Group. Major uplift and erosion within, and adjacent to, the early Cretaceous rift basin in the Mid-Cretaceous, at -95 to 100 Ma, initially constrained the Latrobe Group depositional area to the central deep of the Gippsland Basin and provided an elevated source of quartz-rich detritus for the Latrobe Group reservoirs. This is in marked contrast to the preceding period in the early Cretaceous when contemporaneous volcanism dominated as a source of detritus, producing quartz-poor lithic sandstones, in which a host of attendant diagenetic reactions destroyed their reservoir potential. Initial uplift and erosion of the volcanogenic Strzelecki Group also occurred in the mid-Cretaceous as revealed by a number of distinct inversion structures, and erosion of this material will have locally provided very poor quality sand to the basal Latrobe Group.

Jan 1, 1992

Westwood Quebec Long Life, Low Cost CONSTRUCTION UPDATE ? Shaft advanced to 840m (after 1 year), 3 km of down ramp and 2 km of exploration drift ? Head frame and hoist room structure completed ? 2009, 84,700m drilling program completed (increase 9%) 2010 OUTLOOK ? $102 million expenditures planned ? Shaft to advance to 1,300m and the first loading excavate 71,500m drilling program planned

May 1, 2010

From the massive equipment that moves the earth, to the parts that keep the equipment moving, it was all on display for more than 35,000 people who at-tended MinExpo 2008 at the Las Vegas Convention Center Sept. 22-24. In the largest show in the illustrious history of MinExpo, the success of the recent commodity boom was reflected in the more than 55,700 hm2 (600,000 sq ft) of floor space that was jam-packed with nearly 1,300 vendors. Among them, the makers of the industry?s largest machines, displaying their latest and greatest trucks, shovels, excavators, drills and other mining equipment. During the nearly decade-long commodities boom, equipment makers have worked hard to keep up with demand while also investing heavily in research and development. The beneficiaries of this R&D is the end user who saw first-hand at MinExpo 2008 the many advances that have already been made in safety, comfort and productivity from all the manufacturers. R&D has also helped spark more talk of automation, which is being used already at some of the world?s largest mines. Caterpillar and Komatsu have worked with the technology in surface mining and Bucyrus and Sandvik are among the industry leaders applying the science of automation to underground mines. Technology has in-creased greatly since the idea of moving massive equipment remotely was first knocked around and the idea of entire fleets operating around the clock seems to be getting closer to reality. But, until that happens, MinExpo attendees were treated to a show that featured some of the most impressive current machines the industry has to offer. In the largest booth space of the convention, Caterpillar (www.cat.com) displayed the culmination of an ambitious $280-million dollar investment, with the introduction of its new mining fleet of four new trucks. The F-series was un-veiled with common features in safety, cabs, engines, frames and bodies and Tier 2 compliant engines. The F series also features a return to the electric drive option. ?When our customers asked us for improvements to our mining trucks, we responded by making a record investment in every single truck in our line, as well as the increased capacity to produce more of them,? said Cater-pillar group president Stu Levenick. ?New technologies have allowed us to make trucks more reliable, easier to maintain and more friendly to the operator and to the environment.? The 793-series is in the 218- to 227-t (240- to 250-st) class that will be available in both mechanical (793F) and electric (793F ac) versions. The electric drive-only 313- t (345-st) 795F was also introduced, while the flagship 797B truck is in the process of being replaced by the new 797F mechanical drive, maintaining its 345- to 363-t (380- to 400-st) target payload. Completing Caterpillar?s new mining truck line will be new versions of the 785 and 789 mechanical drive trucks. The next generation of trucks will be phased into production during the next two years, with the Cat ac drive models expected to go into production in late 2010. The $280-million in-vestment is Caterpillar?s largest commitment ever to the mining industry

Jan 1, 2008

By M. W. Hildyard

A blast was engineered close to a tunnel in a deep-level mine with the purpose of studying the wave interaction with the tunnel. Numerical modelling of seismic wave propagation was used in both the forward planning and the back-analysis of this experiment. This paper presents the forward analysis. A likely model for a propagating blast was investigated and developed. This model predicts the influence of the velocity of detonation of the blast and the rise-time of the blast on the radiation pattern, and hence on the expected positions of maximum velocity at the tunnel surface. An attempt was made to quantify the parameters of the blast model, using waveform data from two other blast experiments. The blast model caused particle velocities which were an order of magnitude lower than these measured velocities. Large values for blast pressure were required to match the amplitudes of the recorded velocities. An alternative ?effective? source with a similar mechanism but increased diameter was proposed to account for the higher velocities. It was established that distant velocities scale with the square of the borehole diameter. A calibration blast at the experimental site was also modelled. Agreement in the waveforms was not sufficient for conclusive statements to be made about the validity of the source model. However, the modelled waveforms show an encouraging correspondence with some measured waveforms. This gave confidence that the model could be used to examine wave propagation around the tunnel, and allowed a scaled source to be developed for forward analysis of the main experiment.

Jan 1, 2001

By J. du Plooy

Mintek has implemented a training scheme that provides students with the experiential training requirement for the National Diplomas in Chemical Engineering and Extraction Metallurgy. This note describes the main features of the scheme and the course content, and our view of future developments in this area.

Jan 1, 1998

By D. Rutledge

Discrete (digital) signal processing techniques are proving to be very valuable tools for miners using the block cave method. Waveform analysis of different measured signals associated with active mining provides valuable information on production dynamics and safe operation of the mine. For example, correlation of the three-dimensional surface displacement velocity waveform and the production output waveform reveals a remarkably predictable time-varying physical process. In this paper, the authors discuss the signal processing techniques used to study these relationships, as well as the related implications for mining.

Jan 1, 2008

By Gordon M. Matheson, Douglas A. Anderson, David K. Miller

"Traditionally, analysis of vibrations from blasting has been focused on peak particle velocity fordetermining the likelihood of both annoyance and damage. The US Bureau of Mines, in RI 8507,indicated the importance of frequency in vibration. Methods of controlling the vibration by reducingthe vibration concentrated in certain frequency bands using delays have been successful over the past decade."

Jan 1, 1997

By Andrew Chapman

The scope of the SA (Situational Awareness) working group is to analyze the effectiveness of information delivery systems in mining equipment and develop a unified display design, to mitigate against the proliferation of screens within equipment cabs. This working group comprises a variety of stakeholders representing a cross-section of relevant mining and mining-related organizations. This stakeholder network will help guide the direction of the working group towards a common, mutually beneficial end. For now, the focus is on shovel displays; however it should be noted that this work is expected to form the foundation for similar work with other equipment in the future.

Aug 1, 2013

By Rees J. Llewellyn

High chromium white irons can be formulated to provide required combinations of abrasion and erosion wear resistance, toughness and capability to withstand corrosion attack. As a consequence, they are used widely in casting form throughout the mining/mineral processing industry, particularly as components for slurry pumps and also as mill and crusher liners, laminated wear plates in chutes and hoppers and in valves, nozzles and cyclones. Traditional cast chromium molybdenum and high chromium white irons for wear applications are covered in ASTM A532 Classes 11 and 111 and are also available as comparable proprietary alloys. They rely on heat-treated, hypoeutectic microstructures containing a high volume fraction of very hard eutectic/secondary metal carbides and martensite to provide extremely high wear resistance. The ability to increase the carbide volume fraction and hence achieve higher wear resistance, has been limited because of severe casting difficulties encountered when carbon and chromium contents are raised and hypereutectic alloys with structures also containing coarse acicular primary metal carbides are produced. The limitation has been overcome and cast hypereutectic chromium white iron pump components have established themselves in a wide variety of mineral processing service applications. Comparisons will be made between the microstructures and wear test performance data for the various alloy types and details will be provided of the service performance improvements that have been achieved through the use of hypereutectic chromium white irons.

May 1, 2004

Jan 1, 1987

By H. G. Denkhaus

Please allow me the temerity to reply to your reply to my contribution as follows: A fracture is brittle if plastic deformation is absent or, conversely a fracture is ductile if plastic deformation is present. Consequently, brittleness is specified by the degree of plastic deformation at fracture. This is the generally accepted definition. If other material properties (e.g. the quorient or the product of the uniaxial compressive and tensile strengths) under certain conditions are influenced by brittleness, or brittleness by them, these should not be called brittleness. If the one or the other author does that, he simply uses imprecise language. Even your remark, that ?Inyang and Pitt (1990) stated that the ratio of the compressive strength (sc/st) is directly proportional to brittleness?, confirms that the two quantities are not considered the same. For example:? The well known definition that a material is linear?elastic if the strain is directly proportional to the stress?does not mean that stress (measured in MPa) and strain (measured in %) are the same thing.

Jan 1, 2003

By T. Hudaverdi

Control of the particle size distribution of a muckpile after blasting is always an important subject for mining industry. Blasting has a significant impact on downstream processes such as loading, crushing and grinding. Improvement of blasting results provides increase in loader and excavator productivity due to increased diggability capacity, and increased bucket and truck fill factors. Suitable and uniform particle size distribution results increase in crusher and mill throughput and decrease in energy consumption in size reduction process. Digital image analysis technique has been used for many years in mining industry in order to determine blast fragmentation. The images of muckpile surface can be used to determine the mean fragment size (x50). The source of digital images can also be haul truck, leach pile, waste dump, stockpile, and conveyor belt. The screening that is conventional method to measure blast fragmentation is time consuming and expensive. Digital image analysis is a cost effective and faster method (1).

Jan 1, 2012

By L. Su, S. Liu, K. Jiang, K. Xie

The reduction of iron dissolution and acid consumption is fairly important in the extraction of Ni and Co from laterite ores from both economic and efficiency perspectives. BGRIMM conducted detailed research to investigate the behavior of iron in a nickel laterite leaching process. The mineralogy of Ni and Co was studied. In limonite ore about 76% of nickel is present in goethite while in saprolite ore 79% of nickel is associated with magnesium and silicon minerals. Test work revealed that limonite can be decomposed completely with enough acid concentration during atmospheric leaching. More than 98% of Ni and Co were leached into solution while 85% of the iron was also dissolved with 130-140 g/L iron in solution. Iron precipitates as hematite in the temperature range 250-270?C without neutralization reagents. That’s why limonite is treated by high pressure acid leaching (HPAL) technology to achieve nickel extraction and iron precipitation in the same autoclave. BGRIMM’s test results indicated that the remaining acid in atmospheric leaching solution and acid released by iron precipitation at a lower temperature was enough to leach saprolite efficiently. The so-called inverse leaching technology leaches limonite at atmospheric condition and the leaching slurry combined with saprolite is pumped into an autoclave to leach saprolite at 150-170?C. In the autoclave iron precipitates as hematite without acid consumption. Total nickel and cobalt extractions in the test program were more than 90% with iron content in solution below 8 g/L. In this inverse process iron dissolves in the atmospheric leaching stage and precipitates as hematite in the low temperature leaching stage. Compared with HPAL the leaching temperature is reduced to 150-170 ºC from 250-270 ºC. Compared to atmospheric tank leaching acid consumption is reduced from 850-950 kg/t ore (atmospheric) to 550-650 kg/t ore (inverse).

Jan 1, 2016

By B McCarthy

Mining has been typified of late as a boom and bust, cyclical industry operating against a steady decline in the size and quality of mineral deposits. Decreasing deposit grades and increasing costs of traditional mining techniques, all in the face of another commodity downturn, are forcing mining companies more than ever before to seek out new and innovative ways to operate. New technologies are emerging to model, control and track resources through the mining value chain, to move material about mines more efficiently, and to identify and separate ore from gangue early in the extraction process.Discovering such technologies however is only the first challenge for mining companies. Actually implementing technological change successfully has proved to be an even bigger challenge. Like for many industries, fulfilling the promised benefits for the expense and timing envisioned, has not been easy when innovative technologies are introduced.Citing the author’s insights and experiences in a number of emerging technologies, this paper explores barriers to implementing technological change in the mining context. Key elements of a change management framework, first developed for implementing mine management systems, are described to give mining executives insight into how they and their organisations can succeed through technology-driven change.CITATION:McCarthy, B, 2016. Successfully implementing technology-driven change in the mining environment, in Proceedings International Mine Management Conference, pp 89-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By V. V. Nazimko

Abandoned coal mines cause subsidence and structural damages. Shallow abandoned mines induce the most severe and harmful damages. In addition, they produce time-dependent subsidence which is difficult to predict. Backfilling of underground cavities with waste materials have been used to prevent the time-dependent subsidence or to mitigate its effect. However, this procedure is expensive. A new drill and blast technique has recently been proposed to prevent surface damage from time¬dependent subsidence over abandoned mines. It utilizes the principle that blasting in the caved rock and roof in the vicinity of a cavity will dilate the ground and create a self-supporting effect owing to increase in the volume. Physical modeling has demonstrated that artificial dilation of caved rock using the drill & blast technique creates positive effects due to the following sequence of events: the dilated rock creates a supporting effect for the suspended rock strata and reduces its span which decelerates 3.4 times the process of caving. The roof span is reduced by the next caved layer, which causes the hole boundaries to incline to each other. This effect converts the process of caving from a developing mode to a reduction mode. Finally, the sinkhole zone assumes a triangular shape with a negative angle of draw 64-700 in contrast to a rectangular shape of the chimney zone for natural caving. Vertical dimension of the triangular zone is 3.87 times of the room height. Final surface subsidence decreases at least 2.09 times; displacement 1.31 times, slope 2 27 times; curvature 3.42 times, horizontal strain 1 21 times in comparison to natural caving of the ground over an abandoned mine.

Jan 1, 1999

By Alfred Weiss

Selecting a minicomputer is not unlike selecting a costly piece of mining equipment such as a truck, shovel, crusher, or conveyor belt system. A marked difference might lie in the frequency at which such selection takes place; another difference might be mine management's familiarity with mining equipment vis a vis a minicomputer. These basic differences might prompt a mining company to seek the aid of a consultant when selecting a minicomputer system. Advantages and Disadvantages The fundamental advantage of employing an independent consultant is that it provides management with a source of knowledge and breadth of experience not readily available within the organization. If the consultant has a minerals background, such knowledge and experience are further enhanced by actual experience in exploration, mining, and mineral processing. If the consultant has worked within a mining company, such hands-on experience is supplemented with a meaningful understanding of the client's business; this facilitates communication between the consultant and members of the client organization. The consultant has been, so to speak, "in the client's shoes." There are several other advantages. Since computer systems cut across organizational boundaries, the independent consultant may be able to move within the organization more easily than an inside staff person to collect necessary information. Also, detachment from any manufacturer should provide the client with an objectivity and a set of recommendations as near optimal as feasible. The principal disadvantages lie in the area of continuity and accountability. Once the consultant's report has been submitted and his recommendations implemented, a discontinuity might occur. Also, if implementation does not provide the desired results, the consultant might not be available to correct the situation or account for actions taken. Proper selection of consultant services, relative to kind and duration, and the consultant's method of operation, will often prevent many of these aftereffects. Services Offered The professional consultant can help a client: •Define and summarize information systems technology* needs; • Evaluate alternatives such as in-house capability and capacity, time-sharing, or service bureaus; • Prepare a formal request for proposal (RFP) to be submitted to vendors; •Evaluate vendor proposals; •Evaluate the economics of lease vs. purchase; and •Assist in the conversion and installation. Thus, consulting services may range from evaluating an existing system and upgrading to a larger piece of equipment, to selecting a new first-for-the-organization computer. First, Define and Summarize Needs Regardless of circumstances, the most valuable document required before equipment selection is the information system plan (I/S plan). It helps insure that the company's information needs are met in a cost-effective manner. An I/S plan is usually a comporient of the mining company's overall business goals. Since an I/S plan is a formal vehicle for establishing and communicating the direction the organization intends to take to satisfy information requirements needed to achieve goals and objectives, most initial systems services are likely to center around creating such a document or updating an existing document. The trend toward company-wide I/S planning is increasing in the mining industry; however, smaller scale efforts focused at the information systems needs to support an individual

Jan 11, 1981

By W. I. van Drunick

AngloGold Ashanti Metallurgy has recently been involved in the successful installation of intelligent, expert control systems on the milling circuits. The benefits of expert systems in these highly interactive circuits are obvious. Existing comminution tools, which have been developed and can now be incorporated into online control, include improved modelling techniques and understanding, robust and competent simulation methods, sampling techniques, and optimization methods. The minerals processing industry has seen the benefits of predominantly research-based centres turning their focus to commercial applications of comminution circuit modelling packages, which in turn can be utilized within expert control systems. Expert mill control has been successfully installed at AngloGold Ashanti South Africa?s Mponeng and Kopanang Gold Plants. Expert control has also been installed at AngloGold Ashanti?s West African Sadiola Mine operation. The implementation of the systems has produced a number of positive outcomes. Plant surveys usually result in the identification of sub-optimal areas, and the control philosophy is then configured to ensure that these areas (along with the entire circuit) are optimized and maintained. Outdated PID loops have generally resulted in oscillatory control with large amplitude deviations from set-point. Significant improvements in SAR Metallurgy operations have been realized, firstly through achieving stability in the load and cyclone control, and secondly through online identification and implementation of optimized set-point conditions for mill mass, discharge density, etc. Soft sensors are configured to accurately estimate parameters that were historically not measurable, viz. breakage rate, mill load condition, onlinekWh/t-75 microns, mill discharge density and cyclone overflow grading. The Mponeng Plant system achieved circuit stability and improved overall grind. The Plant was able to pay back the control installation after 3 months, based on the additional recovery obtained from the finer grind. The system at Kopanang Plant has also resulted in enhanced plant recovery as a result of a finer grind and a lower residue gold content. The payback for this system was calculated at approximately 6 months. AngloGold Ashanti Metallurgy is currently expanding the installation of expert control to its other operations. It is also evaluating the performance of various suppliers of advanced control systems.

Jan 1, 2005

By M. Bwalya, L. Mabokela, L. C. Woollacott

This paper presents a study on the ability of the King stratification modelto describe density stratification patterns that are achieved under idealizedconditions. Tests were conducted in a batch jig using artificial particles inseven density classes. All particles in a density class had essentially thesame density, size, and shape. Tests were conducted for particle systemsinvolving from two to seven components. Good agreement was obtainedbetween measured and modelled data to an extent that gave strongendorsement of the mathematical appropriateness of the core equation inthe King model. Somewhat ambiguous results were found with regard toclaims about the independencies of the single experimentally-determinedparameter required by the model.

Jan 1, 2015