Search Documents

By J Wei, A Yo, R Levy

Waste water reuse from municipal and industrial effluents is becoming increasingly important in many areas around the world. Water scarcity, local regulation and environmental impact are driving many industries like coal and copper mines to reuse the large volume of waste water they produce. For example, the Chinese coal industry generated about 4.2 billion tons of mine waste water in 2005 of which only approximately 30 per cent was reused. Coal energy represents 76.6 per cent of the total energy generated in China in 2007 and most of the coal-fired power plants are located in north-west of China, which is a water stressed area.The selection of mine waste water treatment process is challenging as the effluents typically contains high levels of organic compounds and salinity and their composition can vary significantly. In recent years there has been a growing interest in the integration of ultrafiltration (UF) and reverse osmosis (RO) membrane technologies for mine waste water treatment and reuse.In this paper, an overview of the design and performance of ultrafiltration and RO membranes applied for reuse of mine waste water are discussed. A study was carried out in two effluents treatment plants treating copper and coal mine waste water, which are located in Chile and China respectively. The following topics will be discussed to demonstrate the performance of an integrated membrane system in mine waste water reuse: The main challenges from copper mine waste water treatment: high level of chemical oxygen demand (COD); high level of total suspended solids (TSS); high salinity; high concentration of silica, sulfate, iron and other contaminants; and fluctuation of raw water quality. The main challenges from coal mine waste water treatment: high level of total dissolved solids, and waste water quality fluctuation. Design parameters for waste water treatment systems: Selection of pretreatment for dual-membrane system in the copper mine: Clarifier with coagulation and flocculation to remove high TSS; Dissolved Air Flotation (DAF) to remove non-settling solids; Media filtration to handle fine solids and particulate organics; Activated Carbon filters (ACF) to remove dissolved organics, colour and odours. Selection of UF and RO membranes and specific design of their recovery, flux, chemical dosage and cleaning regimes. Finally, the performance of UF and RO, including the main fouling factors and efficient cleaning procedures, will be presented and compared to the design parameters to demonstrate the efficiency and performance of the selected integrated membrane systems in each case.

Jan 1, 2009

By Khaled Morsy

Cementitious seals are made of foamed cements with strength ranging from 100 to 600 psi. These cementitious seals are usually used at locations where the seal will be subjected to some convergence, assuming that this material can absorb entry closure without compromising the structural integrity of the seal. Prior to 2006, Lake Lynn Experimental Mine (LLEM) conducted full-scale tests on various cementitious seals designed to meet or exceed the 20-psi horizontal static load requirements of the old 30 CFR1 75.335. Both hydrostatic and dynamic loading tests were conducted. The structural response (pressure and displacement readings) obtained from these tests were recorded. The stability of the cementitious seal is based on balancing the load applied to the face of the seal from the explosion against the shearing resistance at the seal/rock interface. Therefore, the properties of the seal/rock interface, such as stiffness, cohesion, friction, etc. are critical to determine the stability of a cementitious seal. These properties are usually assumed by the researchers in their models. This paper emphasizes the importance of having the correct properties of seal/rock interface in the numerical modeling. FLAC 3D models were developed to simulate Celuseal2 cementitious seals subjected to both hydrostatic and dynamic loadings. Using the hydrostatic and dynamic loading test data conducted at LLEM, the static and dynamic properties of the seal/rock interface were back calculated. The FLAC 3D models showed good agreement with the test results.

Jan 1, 2009

By Andrew Port, Ali Ghandeharioon

Nonlinear seismic deformation analyses using the finite difference program FLAC were performed for a wastewater treatment plant to estimate foundation displacement and performance of two proposed trickling filters during the 2475-year event design earthquake. The effective stress based constitutive model UBCSAND, which captures the cyclic behavior of both the “sand-like” and “clay-like” materials, was used to model the dynamic response of the soil strata. Dynamic analyses of the site indicated that in absence of ground improvement or deep foundations beneath the proposed trickling filters, those structures would undergo horizontal displacements in excess of 1 m and short-term differential settlement gradient of about 400 mm over 50 m as a result of seismic and post-seismic settlements. Three mitigation options were considered for limiting the seismic displacements and differential settlement gradients of the proposed trickling filters. These alternatives include vibro-replacement stone columns, vibro-replacement stone columns plus supplementary cutter soil mixing (CSM) configurations, and pile foundations. Various layouts for each mitigation option were considered including the lateral extent of the ground improvement, CSM walls and pile spacing. Seismic horizontal and vertical displacements of the proposed structures as well as post-earthquake consolidation settlements due to dissipation of excess pore water pressures in soil layers were assessed in all the analysis alternatives. The analyses indicate that all the alternatives considered have the potential to provide a comparable level of seismic and post-seismic performance. However, for similar performance levels, the ground improvement options need to extend well beyond the edges of the proposed structures, while the piles can be limited to just beneath the footprint of the structures. INTRODUCTION Annacis Island Wastewater Treatment Plant (AIWWTP) is owned and operated by Greater Vancouver Sewerage and Drainage District and services a population of approximately 1 million people in Vancouver, British Columbia. Wastewater is generated by residential, commercial, and industrial sectors and the treated effluent is discharged to Annieville Channel of Fraser River on the south side of Annacis Island. AIWWTP is located on a 51-hectare site and was commissioned in 1975 as a primary treatment plant, but has had two major expansions to meet the population growth needs, and to improve the treatment process efficiency through the provision of secondary treatment of the liquid stream. The current expansion includes construction of additional solids contact tanks and secondary clarifiers. Future expansions include the construction of proposed additional trickling filters. New expansion structures are required to be designed for post-seismic operation after the 2475-year event design earthquake.

Jan 1, 2018

By Tony Lipiec, Chris Fleming, Larry Urbanoski

In 2009, the Canadian Mineral Processors (CMP) became aware that Canadian securities regulators were amending the contents of National Instrument 43-101. NI 43-101 is a set of regulations which establish how ore resources and reserves are presented to the investing public. The documents produced under NI 43-101 are central to the ability of many companies to raise financing for their projects. With the increase of metallurgical complexity, and decrease of head grades encountered in new deposits, the role of the Qualified Person (QP) in determining process performance has become increasingly critical in determining the classification category of resources and reserves. Given the challenges confronted by those involved in defining the concentration and extraction of minerals and metals, there is a need to provide support to these QPs. To address these concerns, the CMP established a sub-committee in 2010 to create a set of guideline documents to assist the QP involved in process matters as to what should be included at the various levels of study supporting the establishment of resources and reserves in NI 43- 101. The results of the sub-committee work are presented and the considerations in the writing of the documents are discussed.

Jan 1, 2011

By J. H. Daniel, S. Krzemien

Partners In Economic Reform, Inc., established a Polish-American Mine Center in Katowice, Poland, in 1996 to improve working conditions in the minerals industry. The program was based on the experience of mining companies, government, and labor in the United States, and was executed by a Coordinating Committee headed by the Center Director and Polish leaders from industry, State, labor, and academia. The cooperation among all parties has enabled safety and health issues to become part of industry restructuring with impressive initial reductions in coal mine fatalities. Existing work practices and attitudes of labor and management were assessed in coal mines throughout the country. Promotion, Rules, and Job and Task Analysis were identified as the areas requiring the most improvement, and are part of a post-graduate Safety Management program. Demonstration projects included measuring dust levels, using safety glasses, and promoting hazard awareness. Improved labor-management relations increased cooperation allowing for effective transfer of technology. Results can also be applied to improve the working environment of the manufacturing sector also undergoing restructuring.

Jan 1, 2001

By S. Banisi, M. Pourkani, A. Kargar, D. Hamidi, M. Sarvi

"Flotation circuit of the Sarcheshmeh copper mine, which processes 40,000 t/d of ore at 0.9% Cu, consists of rougher, cleaning and recleaning stages. To study the stage recovery of copper, one of the eight identical flotation banks was selected for sampling. It was observed that 17% of copper goes to the tailings and the lowest copper recovery was for particles coarser than 105 microns. The third five-cell unit of this bank not only did not recover appreciable amount of copper but also decreased the concentrate grade. The grade of the last five cells was lower than the feed grade suggesting that mixing of the concentrates of the three units was not beneficial. To alleviate the problem, the concentrate of the first four-cell unit was directed to the cleaners feed box (i.e., by- passing the regrind mill). This increased the overall copper recovery by 1.7 %. Also rather than the current practice of adding the reagents only at the feed tank (i.e., 100-0-0%), various combinations of stage addition were examined. It was found that 75-25-0% addition regime could increase the total copper recovery by 1.3%. At the recleaning stage in order to increase the final copper concentrate grade, a froth washing system was used. To ease the maintenance of the system, a shower type washing system was installed. The optimum wash water superficial flowrate was found to be 0.06 cm/s. Continuos sampling of the recleaners with and without wash water over a period of two months showed an increase of 1.5% in the final copper concentrate grade at constant overall copper recovery.INTRODUCTIONThe Sarcheshmeh copper ore body that may rank as third or fourth largest in the world contains 1 billion tonnes averaging 0.9% copper and 0.035% molybdenum. It is located in southeastern Iran and has been processing 40 000 t/d of ore since 1982. The mine produces 100 000 tonnes of copper and 2200 tonnes of molybednite concentrate per year.After three stages of crushing, the ore with a F80 (80% passing size) of 12.7 mm is fed to eight parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of rougher flotation circuit is ground; rougher tails constitute the main component of the plant final tailings. A concentrate with an average grade of 31% Cu (chalcocite and chalcopyrite) is obtained after cleaning and re-cleaning stages. Total recovery of the plant varies between 83% and 87%, depending on operating conditions and ore type."

Jan 1, 2001

By B. K. Shibler, W. G. Sandell, G. M. Potter, H. D. Snedden

"INTRODUCTION During the course of the investigation of the occurrence of manganese deposits in the western United States, examining 'engineers of the Bureau of Mines collected samples from seven manganese properties in Grand and beery Counties, Utah. These were supplemented by five samples submitted by property owners. Since all of the ores were too low-grade for use in producing ferromanganese for steel manufacture, some means of beneficiation was required to produce marketable concentrates, and metallurgical studies were made on each of the samples.Most of the ores Investigated are similar in one respect: At least part of the 'manganese oxide areas contains minute inclusions of gangue. This occurrence materially enhances the complexity of the ore, partly by .increasing the complexity of mineral association, but largely through making manganese-quartz liberation more difficult. In such ores, there is a marked tendency for the manganese minerals to be retained as shells or coatings on the surfaces of quartz particles when crushed. Particles of this type represent considerable loss of manganese in tailing, if gravity-concentration methods are employed, or tend to' float, thus carrying an appreciable quantity of gangue into the concentrate, if treated by flotation.Plus 48-percent manganese sinters were made from some of the ores tested, but, in general, intimate association of manganese minerals with silica limited the degree of beneficiation attainable."

Dec 1, 1947

By Jack G. Croeni

A study was made by the Bureau of Mines to determine the influence of high energy-rate deformation on the structures and properties of low-carbon steel, stainless steel, titanium, titanium-6 percent aluminum-4 percent vanadium, beryllium, molybdenum, and tungsten. The purpose of this study was to determine relative formability, the effect of energy and temperature on metalworking parameters and resulting structures, and the properties of materials formed by this technique. Forming techniques were limited to upset forging and direct extrusion on pneumatic-mechanical forming machines. Results show that considerable grain refinement can be achieved by careful control of deformation and forming temperature by high energy-rate techniques. Significant improvements in strength were observed as a result of this refined structure. Approximate deformation resistance as a function of temperature was determined for a variety of materials.

Jan 1, 1966

By Jerry M. Whiting

Greater awareness of the increasing need to develop supplementary energy sources is accelerating us towards many basic decisions regarding future utilization of mined energy materials -- uranium, coal, oil sands and oil shale. The latter material comprises a major potential source of oil which will require creation of unusually large and low-cost underground mining systems. In this paper, the author briefly outlines and analyzes several of the factors which continue to provide the somewhat unique character of oil shale nine planning and mine operation.

Jan 1, 1974

By R. Hurman Eric

Within the Ag-Pb-S ternary system, the boundaries of the immiscibility region together with the tie-line distributions were re-established at 925°C by the equilibrium-quenching technique where samples were kept in evacuated and sealed silica capsules. Activities of Pb were measured by the dew-point method along the Ag-Pb binary at 925°C, 1100° and l200°C, positive deviations were observed and the results were modeled by the Krupkowski formalism. Activities of Ag, Pb, and S, along the ternary miscibility gap were calculated at 925°C by utilizing the boundaries binary thermodynamics, phase equilibria and tie-lines. Activities of PbS within the pseudobinary Ag2S-PbS mattes were also measured by the dew-point technique and the results were again modeled by the Krupkowski formation where negative deviations were observed.

Jan 1, 2003

By S. P. Pearton

"Pumpable emulsion explosives have been available to surface and underground massive mining operations for decades, and their unique properties offer significant advantages in terms of improved safety, reliability, and performance. However, the benefits of pumpable emulsions have been unavailable to narrow-reef mining operations due to the lack of technology necessary for their successful implementation in this challenging environment. Despite efforts to promote and enhance the safety and performance of bulk emulsions for narrow-reef stoping, little research has been undertaken to advance the pump technologies required for their implementation. This has resulted in a gap in knowledge and technology, and as a consequence the successful implementation of a pumpable emulsion system has consistently eluded the narrow-reef environment.The purpose of the following investigation was to evaluate the viability of pumpable emulsion explosives for use in South African narrow-reef mining operations. By approaching the problem from multiple perspectives, this research aimed firstly to propose a theoretical framework and suite of equipment suitable for the implementation of pumpable emulsions within the narrow-reef environment. Through the development of this suite of pumpable emulsion technology, tests could be undertaken on the proposed narrow-reef emulsion formulation and pumpable emulsion technology to obtain the necessary understanding of the performance of the system under controlled operating conditions prior to its implementation in the broader mining industry."

Jan 1, 2015

By C A. Locke, M Stevens, P Vidanovich, J Cassidy, J L. Mauk

The Karangahake adularia-sericite epithermal gold-silver deposit, located at the southern end of the Waitekauri Corridor, Hauraki Goldfield, occurs as quartz veins with associated alteration haloes. Integrated geophysical studies were undertaken to determine the expression, location, and extent of these alteration zones. Aeromagnetic data show an extensive, magnetic æquietÆ zone over Karangahake and the southern Rahu Ridge that represents a zone of magnetite destruction resulting from hydrothermal alteration. Analytic signal data are used to define the boundary of this zone; the resulting 6 km2 area is elongate north-south with an irregular boundary. A detailed gravity survey over the area reveals a positive residual gravity anomaly, up to 30 gu in amplitude, over the Karangahake deposit. Density measurements on near-surface rocks give low values indicating that the source of this positive gravity anomaly must be deep; possible causative bodies include an igneous intrusion or dense sulfide mineralisation. To the west and east of the host Waipupu Formation, strong gravity gradients of 100 gu/km and 65 gu/km reflect the faulted boundary of the Hauraki Rift, and the edge of the Waihi Basin respectively. High resolution airborne radiometric data define a 2.2 km2 area of potassium enrichment. This area is elongate north-south and has an irregular boundary. It coincides approximately with the centre of the magnetic quiet zone and the peak of the gravity high, and correlates with known areas of intense mineralisation. Anomalously high potassium counts and elevated K/Th ratios correlate with areas of potassic alteration that have undergone K-metasomatism. Underexplored portions of this zone may indicate areas of gold-silver prospectivity. Combined geophysical data therefore reveal the extent of hydrothermal alteration, and the central zone of Kmetasomatism that is most likely to contain orebodies.

Jan 1, 2005

By B. M. Loftus

An investigation into the use of impinging stream (jet) reactors for the leaching of a free milling ore produced an increase in gold recovery by 10% while decreasing leaching time by up to 90%.Tests on refractory ores demonstrate no apparent improvement in recovery. However, leaching kinetics are dramatically increased when these ores are subjected to jet reaction prior to agitation.

Jan 1, 1997

By R. Hurman Eric

Within the Ag-Pb-S ternary system, the boundaries of the immiscibility region together with the tie-line distributions were re-established at 925°C by the equilibrium-quenching technique where samples were kept in evacuated and sealed silica capsules. Activities of Pb were measured by the dew-point method along the Ag-Pb binary at 925°C, 1100° and 1200°C. positive deviations were observed and the results were modeled by the Krupkowski formalism. Activities of Ag, Pb, and S, along the ternary miscibility gap were calculated at 925°C by utilizing the boundaries binary thermodynamics, phase equilibria and tie-lines. Activities of PbS within the pseudobinary Ag2S-PbS mattes were also measured by the dew-point technique and the results were again modeled by the Krupkowski formation Where negative deviations were observed.

Jan 1, 2003

By Benoît Demers

Dans ses opérations de traitement de concentré de zinc, l?usine de Zinc Électrolytique du Canada à Valleyfield génère un résidu minier appelé « jarosite ». Jusqu?en 1998, le jarosite était transporté hydrauliquement dans des bassins construits en argile. Le jarosite sédimenté possède une consistance très molle (impossible de circuler à pied sur le résidu consolidé) avec une eau interstitielle acide contenant des teneurs élevées en métaux. Ces caractéristiques particulières au jarosite rendaient très coûteuses la construction et la fermeture des bassins de résidus. En 1998, Zinc Électrolytique du Canada a implanté un nouveau procédé, développé chez Noranda, dont le principal objectif était de stabiliser chimiquement et physiquement le jarosite. Un nouveau concept de déposition a été élaboré pour le nouveau résidu minier appelé « jarofix ». Les grandes caractéristiques du nouveau procédé et du concept de déposition sont : ? Le jarosite est lavé et déshydraté à l?usine avec un système de filtre; ? De la chaux, du ciment et de l?eau sont ajoutés pour former le jarofix; ? Le jarofix est transporté par camions jusqu?à l?aire d?accumulation; ? À l?aire d?accumulation, le résidu est géré selon un concept d?empilement. L?élaboration du concept d?empilement et de l?aire d?accumulation devait tenir compte des caractéristiques de déposition du jarofix, de sa résistance à l?érosion hydrique et éolienne, de la gestion de l?eau de ruissellement, de la faisabilité de construire les digues de ceinture en utilisant du jarofix durci et de la nécessité de restaurer progressivement l?aire d?accumulation. Le déchargement du jarofix se fait à partir d?une rampe qui progresse avec une pente ascendante pour développer un front de déversement de plus en plus haut. La hauteur du tas de jarofix atteindra 30 m au centre du site. L?aménagement initial de 1998 a inclut une digue d?amorce de 3 m de hauteur, une rampe de déversement de 8 m de hauteur et un bassin pour la gestion de l?eau de ruissellement. Les propriétés du jarofix consolidé dans l?aire d?accumulation sont déterminées annuellement. Le jarofix durci possède la consistance et la résistance d?une argile très raide. Sa conductivité hydraulique est similaire à celle d?un silt et il résiste bien à l?érosion éolienne. Après trois années de déposition, la température du jarofix au milieu du dépôt demeure élevée. Le jarofix durci est facile à excaver et à compacter, ce qui en fait un excellent matériau pour la construction des digues de ceinture en périphérie du site.

Nov 1, 2002

By Rob Sloan, Simon Yu, Rob Robison, Mark Schmidt

"In 2000-2009, Highland Valley Copper (HVC) tested new generation 660 mm cyclones supplied by various manufacturers in an aim to replace existing first generation 762 mm cyclones without success. Due to plant infrastructure limitations, new generation larger (838 and 800 mm) cyclones were not feasible. In 2010, an approach of testing hybrid 800 mm diameter cyclones was initiated by HVC. The hybrid cyclone consists of an 800 mm cyclone upper head section and the use of existing 762 mm cyclone conical sections. Three hybrid 800 mm cyclones were engineered and fabricated, targeting a throughput of 850-950 mtph and were installed in the E line cyclone cluster. Since starting operation on September 20, 2011, three hybrid 800 mm cyclones have been running at combined throughput ranges of 750 to 1050 mtph. Based on plant Daily Met Reports, the test hybrid cyclones demonstrated a decrease in misplacement of coarse copper bearing material to the cyclone overflow and better cyclone efficiency when compared to the existing 762 mm cyclones at the same throughput. The hybrid 800 mm cyclones also demonstrated significantly higher capacity per unit when compared to the existing cyclones. Based on the improvement demonstrated in the full plant trials, HVC decided to install the new hybrid 800 mm cyclones in all five grinding lines starting in July, 2012. A more detailed discussion of the full plant trials and initial results of the first complete retrofit of E line will be presented. INTRODUCTIONHighland Valley Copper Partnership (HVC) is Canada’s largest base metals mine and one of the world’s largest producers of Cu-in-concentrate. The mine, located in the central interior of British Columbia, is owned (97.5% interest) and operated by Teck Resources Ltd. In 2011, HVC produced about 210 million lbs. of Cu and 8 million lbs. of Mo. HVC’s Mill Modernization Project (MOP), which was budgeted for $475 M, is currently under intensive construction and is scheduled for commissioning in Q1 2014. The following description was valid at the time of writing this paper.The operation has been expanded a number of times since the startup of the original Lornex mill in 1972. The plant started up with two 9.75 m (32 foot) diameter primary SAG mills. It was expanded in 1981 with the addition of a 10.36 m (34 foot) diameter SAG mill. In 1988, the Highmont concentrator grinding mills and flotation section were moved and attached to the Lornex mill site. This added two10.36 m (34 foot) diameter AG primary mills to the Highland mill. This brought the total number of primary mills to five referred to as Line A, B, C, D and E: three SAG mills (A, B and C) each with two ball mills in parallel and two AG mills (D and E) each with one ball mill. Each AG mill line is equipped with one short head pebble crusher. Ball mill circuits are classified using 8 clusters of ten Linatex 762 mm cyclones to reach a target P80 330 micron (equivalent 43% +100 mesh), before the cyclone overflow product advances to the bulk flotation circuit."

Jan 1, 2013

By Thomas T., Read

E DUCATION for the mineral industry was at first a single comprehensive curriculum, but it was early recognized that the main basis of mining is physics, while that of metallurgy is chemistry. The first school to offer curricula leading to degrees in mineral industry education in the United States (1853) had separate ones in mining and metallurgy. The Columbia School of Mines (the first really successful one) had only a single curriculum when it opened in 1864, but within a few years had so reorganized its work that it offered curricula in mining, metallurgy, geology, chemistry, and civil engineering. Interest in the metallurgy or geology curricula was slight at first, and for the next 30 years the great majority of Columbia students took the mining curriculum, probably partly because it contained nearly as much geology as the geology curriculum, practically all the metallurgy, and most of the chemistry, and partly because of the degree awarded for it. Other schools kept their mining curricula equally broad, and as late as 1900-1910 men were graduating as mining engineers who were practically as well prepared to make geology or metallurgy their life work, as they were for mining. Gradually, however, the subject matter of mining geology and metallurgy became so enriched through research and development that separate curricula in them became worth while; their progressive development is the subject of another chapter. Mining curricula also began to be somewhat diversified, and schools in areas where coal mining was of outstanding importance began to offer options in coal mining, the earlier curricula having been chiefly aimed at metal mining. The petroleum industry began its meteoric rise about the same time as mineral instruction in this country, but little more of applied science attended its birth than had attended such ancient practical arts as copper and iron

Jan 1, 1941

By L. P. James, W. W. Atkinson

Utah has produced about one billion troy oz. (31.7M tonnes) of silver, more than any U.S. state except Idaho. Several very high grade ore systems, now closed, occur within large polymetallic limestone-hosted districts related to plutonic complexes. These Utah mines fed several major lead smelters for nearly a century. Interaction of magmatic chloride-rich fluids with carbonate rocks localized significant bonanzas within these districts. A low sulfidation state was produced in the fluids by their passage through limestones. The Bingham porphyry mine has also yielded more byproduct silver than other porphyry copper-gold systems. Away from exposed intrusive rocks, some large silver-only systems occur in Mesozoic sandstone and in caldera-related veins in volcano sedimentary rocks. Thick permeable latest-Proterozoic basement meta quartzite sequences present beneath western Utah may have been important, as perhaps they were in the Coeur d’Alene district of Idaho, in providing chloride and silver-rich ore fluids. However, it is clear that specific Tertiary magmatic events played an essential role in the evolution of the Utah silver-rich metallogenic province. The largest silver districts in the state are genetically related to porphyritic plutonic rocks.

Jan 1, 2000

By W. T. Reid

A shortage of anthracite for home heating indicates the necessity of using other fuels for this purpose; low-volatile bituminous, or "soft" coal is the most feasible supplementary fuel, either burned alone or when mixed with anthracite. Comparison of Bituminous Coal and Anthracite Whereas anthracite is clean, burns without smoke, and requires little attention, bituminous coal is dusty, tends to burn with a smoky flame, and forms coke in the fire pot that must be broken up to maintain a continuous high output of heat. When properly fired, however, bituminous coal responds more quickly than anthracite to changes in damper settings and consequently can supply more heat in a short time. It is generally less expensive and usually contains less ash than anthracite.

Jan 1, 1943

By Matters, R T, Coldham, Slee, J C, R J, Wallman

The Committee desires to thank the managers of the various mines along the line of lode for their hearty co-operation in its labours. It would also extend thanks to Messrs J C Moulden, Howchin, Twelvetrees, and the West Australian Geological Surveyfor various information; to Messrs J G Dreyer, S Pope, T Read, P Moncrieff, R Williams, and W J Rose for analyses; and to a number of local gentlemen for advice and help. Professor Skeats, of Melbourne University, gave much valued assistance in petrology, and Mr Herbert Lavers kindly undertook the study of the garnets.INTRODUCTIONThe famous Broken Hill lode is situated in a low range of hills, the Barrier Ranges, near the western border of New South Wales. It has been worked since 1884-fust for silver, then for silver and lead, and at present for lead, silver, and zinc...

Jan 1, 1910