Search Documents

By L. Guttman

THE equilibrium diagram of the indium-thallium system was of interest to us in connection with a study of the superconducting properties of metallic solid solutions in progress at this Institute. For this purpose, a series of alloys was prepared covering the range from pure indium to 75 atomic pet TI, and X-ray diffraction patterns were obtained. Roughly speaking, the results indicated a region of continuous decrease in the axial ratio of the face-centered tetragonal structure from the value ca. 1.08 in pure indium to unity at about 23 atomic pct TI. From this concentration to the solubility limit, the structure was face-centered cubic, a form not reported by Hansen.1 At this point we became aware of the work of Valentiner,2 who had found the same structures at room temperature but had not investigated further the relationship between them. To study the transformation f.c.c.??f.c.t., and to clarify the phase diagram, we undertook the work reported in this paper and that which follows." Preparation of Alloys Pure indium and thallium* (both about 99.9 pct, as estimated from spectroscopic analyses) were weighed out in quantities sufficient to prepare 10 to 25 g of alloy of the desired concentration. (Occasionally indium was mixed with a previously pre- pared solution.) The metals were melted over a flame, in an open graphite crucible, stirred with a graphite rod, and poured into a graphite trough. The rough slug was hammered and swaged into a rod of 2 to 3 mm diam, and annealed in a drying oven at about 125°C for 1 to 2 days. Samples were taken from the rod for analysis, as well as for diffraction and other measurements. The thallium was determined by electrometric titration, using a modification of the method of Beale and co-workers.' The precision of analysis was generally about 2 0.2 pct of the thallium content. The rods were sometimes found to vary in thallium content as much as 1.5 pct from end to end, but since analyses were also made close to the segments used in the various studies, the composition was usually known as accurately as the analyses could be made. Where one less significant figure is given, the error is estimated to be ±0.4 pct of the thallium content. X-Ray Diffraction Measurements Three different cameras were used: (1) A 7 cm Debye camera, with oscillating specimen (manufactured by the Picker X-ray Corp., Cleveland, Ohio); (2) a 9 cm diam Debye camera of the type designed by Bradley;" (3) a 10 cm diam symmetrical focusing back-reflection camera (manufactured by Geo. C. Wyland, Ramsay, N. J.). Samples were prepared from the homogenized rods, either by filing under liquid nitrogen, or more often, in the form of wires or foils made by working at room temperature or liquid nitrogen temperature. Sharp patterns were obtained from specimens annealed at room temperature, although higher annealing temperatures were also used (cf. below). Generally, copper radiation was used; a few patterns were obtained with

Jan 1, 1951

By Perry Olcott

The Texas Gulf Coast had a rather disappointing year in the type of oil fields found. Although 17 fields were found in the area during the year, as against 21 fields in 1938, no field of major proportion was discovered. Of these 17 fields, 11 were oil fields, 4 were gas and distillate fields, and 2 were gas fields. The wildcat activity for the year resulted in about 400 dry holes, although probably 10 per cent of these were edge wells close to proved areas. During the year, 1455 oil and gas wells were completed as compared to 1637 wells in 1938, a decrease of 11 per cent. Production for the Texas Gulf Coast area for the year was 100,253,937 bbl. as against 92,530,467 bbl. produced in 1938, an increase of 8 per cent. The daily average production was 274,668 bbl. for the 365 days in the year, although only 252 producing days were allowed by the Railroad Commission; that is, 69 per cent of the time as compared to 71 days shut in for 80 per cent of the time producing in 1938. The total number of oil and distillate wells producing at the end of 1939 was 9495 as against 8451 at the end of 1938—an increase of 1044 wells, or 12 per cent. Of these wells, 6547 were flowing and 2948 pumping, or 69 per cent flowing. At the end of the previous year, 66 per cent of the wells were flowing. New Fields Angleton, Brazoria County.—The Angleton field was discovered by the completion of Glen McCarthy's No. 1 Carr in October for an initial production of 180 bbl. a day of 50" gravity oil through 11/64-in. choke with 3400 Ib. on tubing. The field is 1½ miles east of the town of Anchor. The discovery undoubtedly can be credited to the reflection seismograph, since several companies worked the area from 1933 onward with this type of exploration. The principal block was taken by the Humble company in 1934. Two deep holes by Humble revealed the presence of structure, although both were dry. The Humble and Sun companies later contributed money and acreage toward the drilling of the discovery well. The production is from a sand in the Frio, about 1700 ft.

Jan 1, 1940

By Perry Olcott

The Texas Gulf Coast had a rather disappointing year in the type of oil fields found. Although 17 fields were found in the area during the year, as against 21 fields in 1938, no field of major proportion was discovered. Of these 17 fields, 11 were oil fields, 4 were gas and distillate fields, and 2 were gas fields. The wildcat activity for the year resulted in about 400 dry holes, although probably 10 per cent of these were edge wells close to proved areas. During the year, 1455 oil and gas wells were completed as compared to 1637 wells in 1938, a decrease of 11 per cent. Production for the Texas Gulf Coast area for the year was 100,253,937 bbl. as against 92,530,467 bbl. produced in 1938, an increase of 8 per cent. The daily average production was 274,668 bbl. for the 365 days in the year, although only 252 producing days were allowed by the Railroad Commission; that is, 69 per cent of the time as compared to 71 days shut in for 80 per cent of the time producing in 1938. The total number of oil and distillate wells producing at the end of 1939 was 9495 as against 8451 at the end of 1938—an increase of 1044 wells, or 12 per cent. Of these wells, 6547 were flowing and 2948 pumping, or 69 per cent flowing. At the end of the previous year, 66 per cent of the wells were flowing. New Fields Angleton, Brazoria County.—The Angleton field was discovered by the completion of Glen McCarthy's No. 1 Carr in October for an initial production of 180 bbl. a day of 50" gravity oil through 11/64-in. choke with 3400 Ib. on tubing. The field is 1½ miles east of the town of Anchor. The discovery undoubtedly can be credited to the reflection seismograph, since several companies worked the area from 1933 onward with this type of exploration. The principal block was taken by the Humble company in 1934. Two deep holes by Humble revealed the presence of structure, although both were dry. The Humble and Sun companies later contributed money and acreage toward the drilling of the discovery well. The production is from a sand in the Frio, about 1700 ft.

Jan 1, 1940

By B. Y. Ekber, A. S. Gorbachev

The development of economically effective and safe methods of mining thick coal seams allow considerable coal reserves to be used as an energy resource all over the world.

Jan 1, 1979

By Harry A. Lipsitt, Attwell M. Adair

A number of papers have appeared in the past several years concerning the nature of the fatigue limit. The hypotheses presented in those papers fall into three groups. Some authors attribute the fatigue limit to the distribution of interstitials prior to testing (static group). Others consider the fatigue limit to be due to dislocation-interstitial reactions during testing (dynamic group). Still other propose that the fatigue limit results from a characteristic peculiar to the iron (bee) lattice (inherent group). This communication is an attempt to digest the salient features of each of the hypotheses, discuss them, and present some constructive criticism. It is shown that each of the extant ideas has some merit, and that each of the mechanisms thus far proposed is necessary, but individually insufficient, to provide the desired level of understanding of the fatigue-limit behavior of metals. Static Group. The data of Oates and wilson1 on finegrained (=0.022 mm diam) low-carbon steel indicate that the fatigue limit exists in the absence of sufficient plastic deformation for any dynamic strain-aging mechanism to be operative. Specimens tested just below the fatigue limit showed yield-point behavior typical for unstrained material when removed from the fatigue machine and tested in tension. These results led them to the conclusion that initial dislocation locking controls the fatigue limit in this material, which has a yield stress higher than the fatigue-limit stress. Prestraining this material just prior to fatigue testing would be expected to lower the fatigue-limit stress; this they observed experimentally. Yoshikawa and sugeno2 are of the opinion that the sharp fatigue limit in fine-grained iron is caused by

Jan 1, 1967

By V. P. Yashin

Modern trends in the use of autogenous grinding of minerals have been investigated by Mekhanobr Institute. The conclusions drawn are based on experimental and theoretical investigations by the author and his coworkers. A method is suggested for determining the efficiency of converting from ball milling to autogenous grinding. A qualitative interpretation is given for comminution theory using both methods. This interpretation is used as a basis for considering both the principal trends in increasing use of primary autogenous grinding and the results of such in industrial application. Data are given from testing some ores from USSR deposits for the effect of the ore Preparation step on subsequent metallurgical treatment. Autogenous grinding is shown to be widely used in various USSR industries.

Jan 1, 1980

By R. Clare Coffin

The production of oil in the Rocky Mountain district, including southeastern New Mexico, increased from 33,048,630 bbl. in 1930 to 34,325,163 bbl. in 1931. This increase was due to production in New Mexico, which exceeded the 1930 figure by approximately 5,000,000 barrels. Total production by fields is given in Table 1. Exploration during 1931 resulted in the discovery of a new oil-producing horizon in the Big Muddy field in Natrona County, Wyoming, and ' the discovery of a new gas pool in the Powder Wash structure, Moffat County, northwestern Colorado. Gas was discovered also in the Frontier sands of the Bunker Hill dome, Carbon County, Wyoming, but no test has yet been made by which to determine the significance of this discovery. All other exploration which resulted in increasing the known reserves of oil and gas in the district was confined to drilling in partly outlined fields where known limits of production were extended. During the year two major gas pipe lines were completed in western Montana, and one in southwestern New Mexico was extended into Arizona. One new project involving the marketing of natural gas from Wyoming fields included the conversion of an existing oil line to a gas line to serve towns in southeastern Wyoming and western Nebraska. Colorado The decline of 132,501 bbl. in the production of oil in the Colorado fields during 1931 from the figure of 1930 is due to the natural decline of existing wells, partly offset by the increased production in the Greasewood area. New exploration was limited largely to northeastern Colorado, where attempts were made to find oil in areas adjacent to the Grease-wood field. Powder Wash, Moffat County.—The Ohio Oil Co. is to be credited with the discovery of a gas field in the Power Wash structure in Moffat County, Colorado. The initial well drilled in sec. 5-11-97 encountered a sand at a depth of 2152 ft. which produced 34,188,000 cu. ft. of gas on an open-flow test. The rock pressure was reported as 630 Ib.

Jan 1, 1932

By R. K. Datta, T. S. Davis

YVO4:EU, excited under 3650A radiation, shows a marked increase in total brightness with in~rease in temperature. At 25°C the response to 3650A radiation is about 48 pct of its maximum response which occurs at about 350°C, Fig. 1. In an attempt to explain the phenomenon, one of the present authors' (R.K.D.) investigated the diffuse reflectance spectra of the phosphor at different temperatures (up to -150°C) and was unable to observe any significant change to which the increased brightness could be reasonably ascribed. Since then diffuse reflectance spectra at elevated temperatures have been obtained in this laboratory using an improved device. A significant decrease in the diffuse reflectance of a phosphor in the ultraviolet region—especially in the longer wavelength region—at -300°C has been observed. The purpose of this note is to describe the device used for high-temperature reflectance measurements and to explain the increased brightness of YVO4:Eu phosphor at elevated temperatures under 3650A excitation. Experimental. YVO4 and YVO4:Eu samples were prepared as previously described.' The elevated-temperature reflectance spectra were obtained with a Cary 14 spectrophotometer equipped with a diffuse reflectance accessory and a ring collector. CaF2 was used as the standard. The cell used

Jan 1, 1969

By R. Clare Coffin

The production of petroleum in the Rocky Mountain district increased from 27,104,436 bbl. in 1929 to 33,048,630 bbl. in 1930. This increase was due to the development in southeastern New Mexico; which is in reality a portion .of the West Texas province. Disregarding production in southeastern New Mexico, the Rocky Mountain district produced 25,799,027 bbl. in 1929 and 23,164,988 bbl. in 1930, a decrease of 2,634,039 bbl. for the period. The daily production in January, 1930, averaged 70,839 bbl. for the entire district and in December, 1930, the daily production was 98,995 bbl. Total production by states is given in Table 1. Three important discoveries of oil and one of gas occurred in the district during 1930 in structures not, previously known to contain oil or gas. Oil was discovered in Dry Creek structure, Carbon County, Mont.; in the Midway structure, Natrona County, near Casper, Wyo.; and in the Greasewood structure, Weld County, Colo., northwest of Fort Morgan. Gas was discovered in the Bell Rock structure in Moffat County, western Colorado. Seven deep tests in as many different fields encountered oil in lower horizons than those already exploited. All of these discoveries were in the state of Wyoming. They occurred in the Salt Creek field, Natrona

Jan 1, 1931

By A. N. Holden, J. H. Hollomon

Inhomogeneous yielding during the early stages of plastic flow has been observed in many metals and has long been a subject of controversy. Low carbon steel, when strained at room temperature, exhibits a distinct yield point at which the metal ceases to behave elastically and begins to flow plastically without further increase in stress,† often with an actual decrease in stress from that existing at the yield point. One manifestation of this behavior is the familiar Lüders lines. The extent of the yield point elongation (the plastic strain which results without raising the stress above that at the initial yield point) may be several percent. Several explanations of this type of yielding in steels have appeared in the literature:1-3}; 1. The segregation of carbides or other constituents at the grain boundaries of ferrite forms cell-like blocks which break down at a higher stress than that at which the ferrite alone will flow. 2. The precipitation of various constituents within the ferrite itself in some way blocks initial flow until a higher stress is reached, after which a great deal of flow occurs without further increase in stress. 3. The restraining influence of neighboring, less favorably oriented grains in a polycrystal results in a storing up of energy, which on yielding is sufficient to cause the continued propagation of slip bands on the multiplicity of slip systems available in adjacent iron crystals without increase in stress. 4. Local segregation of carbon atoms increases the stress required for the initial propagation of dislocations. The stress required for further deformation is lower.3 Such an explanation would require the presence of upper and lower yield points in single crystals. Low and Gensamer2 have shown that heterogeneous yielding can be eliminated by removal of carbon and nitrogen from polycrystalline steels by wet-hydrogen treatment. They also demonstrated that the re-introduction of minute amounts of carbon or nitrogen caused a return of the yield point. Observations of the initial flow of single crystals containing small amounts of carbon and nitrogen- should provide a clue to the explanation of inhomogeneous yielding. Previous tests of iron crystals4-6 can not be considered conclusive because it is uncertain whether the carbon and nitrogen were satisfactorily removed by the decarburization technique employed. The purpose of the experiments described herein was to determine whether single iron crystals containing either carbon or nitrogen would exhibit in-homogeneous yielding. Experimental Procedures THE PREPARATION OF SINGLE CRYSTALS All crvstals were formed in the following way. Aluminum killed sheet material 80 mils thick was machined into specimens of the outer contour shown in Fig 1. These mildly tapered specimens were decarburized at 730°C for 16 hr in hydrogen that had been bubbled rapidly through water maintained at 70°. The resultant grain size after decarburizing was approximately ASTM 5. Several stress-strain curves were made of the decarburized niate-

Jan 1, 1950

By D. C. Buffum, L. D. Jaffee

THAT the path of brittle fracture in temper brit-tle steel differs from the path in unembrittled steel has been known for some years1 More recently it has been recognized that alloy steels, at least, display two forms of temper brittleness1 which may be called upper-nose and lower-nose. No experimental evidence has been published, however, to show that the two forms can be distinguished by simple inspection of brittle fractures. Fig. 1 is a photograph of the fractured surface of a V-notch Charpy specimen of SAE 3140 steel in which temper brittleness developed during heat treatment in the lower-nose temperature range.' The steel was austenitized 1 hr at 900°, tempered 1 hr at 675", and embrittled 48 hr at 500°C, with water-quenching after each treatment. The temperature of transition from ductile to brittle fracture in the Charpy test was + 2°C (criterion of transition: 100 pet fibrous). The hardness was Re 25; the austenite grain size ASTM 8. This specimen was broken at 150°C in the standard Charpy test and absorbed 6.6 ft-lb; its fracture was rated 0 pet fibrous. Fig. 1 shows that the fracture appeared rough to the naked eye. At the side of the specimen away from the notch (the side which was in compression during the test), the surface as a whole deviated sharply from a plane. At higher magnification, X60, the surface gave

Jan 1, 1959

By D. I. Bardos

The occurrence of Laves phases (AB,) in various binary alloy systems has been reviewed in recent papers.13 Iron forms Laves phases with Sc-, Ti-, V- and Cr-group elements. However, two of the corresponding Laves phases with cobalt, namely MoCo, and WCo,, are missing. Nickel forms binary Laves phases with Sc and Y, but not with any Ti-, V-, or Cr-group element. These conditions are schematically illustrated in Table I. That electron concentration is a significant factor in determining which type of Laves phase is formed in a given case was recognized long ago by Laves and Witte,4 This concept has been more recently applied to Laves phases formed by transition ele-ments. It now appears that the average electron concentration (average number of electrons per atom outside of the closed shells of the component atoms) may be an important factor also in determining whether or not a Laves phase can occur at all in a given system. As shown in Table I, in the transition element systems considered Laves phases are absent at electron concentrations of 8, or larger (to the right and below the double line in Table I). These absences clearly cannot be accounted for on atomic size considerations, as evidenced by the many inconsistencies apparent in Table 11. While the ideal radius ratio for Laves phases is 1.222, in the systems which do have Laves phases the ratios of CN 12 radii range from 1.10 to 1.46. The consistent absence of Laves phases at RA/RB< 1.10 might be attributed to the low values of these radius ratios. However, Table II shows that absences also occur irregularly throughout the radius ratio range covered. In a previous paper7 it was concluded that, in transition element systems forming u-phases, silicon may act as an acceptor of electrons, thus stabilizing the u-phase at electron concentrations higher than

Jan 1, 1962

By Suzanne T. Mathis, J. C. Ferm, J. T. Berger, W. Horger

A system of core logging and computerized entry and retrieval is described which permits accurate and rapid logging of core, cuttings and geophysical records derived from exploration and development bore holes. The system is so constructed that older drilling records can also be utilized. Output consists of conventional computer print out and graphic logs with a variety of scales, symbols and formats. Such logs can be used in constructing rock profiles which are necessary in property assessment and mine development.

Jan 1, 1983

By R. L. Robinson, P. DeFrank, R. F. Hatfield

Production equal to or greater than open-hole completions is possible through perforated completions if the flow paths throughout the perforations are free of obstructions.&apos; Previous investigations have indicated that, in some cases, maximum productivity is not obtained due to plugging of the perforations with debris from the wellbore fluid and/or debris from the perforating process. Control of wellbore fluid and proper well completion techniques are very important in the elimination of perforation plugging.&apos; Selection of properly designed perforating equipment also is quite important for maximum well productivity. Studies made with the use of the perforation flow laboratory, in which perforating tests are run under simulated well conditions, have shown that perforation plugging occasionally occurs. Plugs in perforations result from various causes. One of the contributors to plugging that can be controlled by the perforating device is the slug or carrot resulting from jet perforating. This condition has undergone extensive study, and previous developments have resulted in a decrease in carrot size—but not in complete elimination. It was felt that, if a method of completely eliminating the carrot could be found (with charge performance equal or better than previously obtained), a significant contribution would have been made. Such a charge has been developed and is reviewed in this paper. THEORETICAL CONSIDERATIONS OF CARROT ELIMINATION There are several popular theories of how a shaped charge jet is formed."," One of these is the hydrodynamic theory, wherein the liner is treated as a fluid under the impact of the explosive forces. Another is the spalling theory, where the interaction of shock waves in the liner causes small particles to be torn from the inner surface of the liner and projected at high velocity toward a common focal line to form the jet. It is not unreasonable to assume that both of these theories may be partially correct. For purposes of our discussion, it is simpler to use the second theory. Generally speaking, when a plate of metal is attacked by an explosive shock pulse, the pulse is transmitted through the metal at high velocity, as shown in Fig. 1(A). Pressures at the shock front may be 6 X 10&apos; psi or higher. This shock wave (a compression wave) upon striking a free surface, Fig. 1(B), is partially reflected back as a tension wave. The interaction of the tension wave with the decaying compression wave causes a stress concentration in the metal; when this stress becomes great enough, a failure occurs and a small particle flies off and is projected away from the metal surface, as shown in Fig. 1(C). A new free surface is then presented to the shocks; the process repeats itself until there is no longer enough energy to cause failure, leaving a portion of the metal relativcly untouched. See Fig. 1(D). To apply this theory to a perforating shaped charge, consider the flat plate to be folded into a somewhat conical shape, with a column of explosive placed in intimate contact with the cone (Fig. 2). An explosive initiator detonates the charge, creating a shock wave

By J. D. Price, W. M. Bertholf

THE central washing plant of the Colorado Fuel & Iron Corp. was first operated in 1918 to furnish coal for two 60-oven batteries of Koppers design. Prior to that time the coke for the blast furnaces had been secured from a number of beehive operations, some with their own washeries. The original washery had four Elmore jigs, which did not do as well as had been expected. In 1923 the jigs were taken out and replaced by Deister Plat-O tables, with various changes in auxiliary equipment. In 1936 the throughput of the plant was considerably increased by the installation of vibrating filters for recovery and drying of fine coal, thereby reducing a large recirculating load of fine coal which passed through the screens of the Carpenter driers.

Jan 12, 1954

By Gram Curtis

The keen and close competition now ruling in the iron and steel manufacture requires imperatively, in the design and construction of the machinery employed, the fulfilment in the highest practicable degree of two cardinal conditions: economy of labor in operation, and durability. The daily pay-roll and the cost of repairs far outweigh in importance the interest on the first cost of this part of the plant. It is believed that the apparatus here described will be found to embody, in these respects, a substantial imprevement upon the present manner of handling ingots and moulds at our large steel-works. Although it includes a number of novel features, it consists essentially in the choice and grouping of certain approved economical devices specially suited to the particular service required. Fig. 1 is a plan, and Figs. 2 and 3 are elevations of parts of a Bessemer converting-house, together with a small portion of the blooming-mill—suficient to illustrate clearly the means and manner of handling the ingots and moulds. A short cable-road of simple form, somewhat similar to those used

Jan 1, 1892

By J. P. Smith

Permian salt measures carry extensive lenses of soluble potash salts in north central Germany. Potash deposits of Oligocene age are found in the Upper Rhine Graben of Alsace (France), and in the Catalonian Basin of Spain. These deposits are found in a wide range of structural settings. Reserves are large, and the production of potash salts is an important phase in the economy of each of these countries.

Jan 1, 1950

By F. Kurata, P. C. Davis, T. L. Gore

An experimental method and apparatus for the study of the low-temperature phase and volumetric behavior of volatile mixtures are described. The phase diagrams, including the critical points, and the volumetric behavior of a natural gas and a mixture of the natural gas with methane at temperatures from -40°F to -200°F and pressures to 1.200 11si are givrn. INTRODUCTION Knowledge of the phase and volumetric behavior of mixtures of the light hydrocarbons at low temperatures is becoming increasingly important as interest in low-temperature separation processes increases. Distillation at low-lemperatures has been used for some time to recover ethane and ethylene from natural gas and refinery gas for petrochemical uses. Removal of excess nitrogen from natural gas by distillation has been proposed as a means of increasing the capacity of gas transmission lines and of improving the marketability of the gas.1,2 Evaluation of the latter process has been hampered, however, by the scarcity of data from which the phase behavior of natural gases at low temperatures might be predicted. While existing correlations of vaporization equilibrium constants may be used to predict the behavior of such mixtures at lower pressures, high-pressure computations often require knowledge of the location of the critical point of the system involved. Although correlations have been developed for the prediction of the critical temperature and pressure of certain types of hydrocar-bon systems, they do not apply to very volatile systems such as nitrogen-bear-ing natural gases. This paper describes the initial stages of an investigation of the low-temperature behavior of a numher of natural gases and other gases of commercial interest. The experimental method and apparatus are described. and the phase and volumetric behavior of a natural gas and a mixture of the natural gas with methane are presented. PREVIOUS WORK The published low-temperature vapor-liquid equilibrium data for hydrocarbons and mixtures of hydrocarbons with nitrogen and helium are listed in Table I. Most of these data are for binary systems, and the data of Stutz-man and Brown" at 100 psi are the only data on a natural gas. The data of Bloomer and Parent3 on the methafie-nitrogen system, which have been phblished since this study was completed, are a valuable addition to the knowledge in this field. Prior to the publication of these data the only published critical point data on systems having critical temperatures below the ice point were those of Ruhemann.1 on the methane-

Jan 1, 1952

By J. S. Osoba, J. G. Richardson, F. M. Perkins

Laboratory experiments have shown profound diffcrences in the behavior of so-called "fresh cores" from the East Texes field and of the same cores after ex~ractio~l with organic solvents. The residual oil satura/ion remaining after waterflooding fresh cores was appreciably lower than the corresponding saturations after flooding extracted cores. This behavior was also reflected in the water-oil relative permeability-saturatiorl relations, which were more favorable for high oil recovery from the fresh cores. These differences were evident not only in the amount of residual oil left after wafer flooding, but also in the saturation water remaining in the core after displacernent by oil. Residual water saturation after displacernetzt of water by oil was higher in the fresh cores than in the extracved core,. Capillary pressure-saturation relations were also different for the fresh crnd extracted cores. Imbibition experiments indicated that both fresh and extracted Bast Texas cores imbibed water spontarteOLISIY, but- the rate of imbibition of water was higher for samp1es after. extraction than it was for fresh core. material. INTRODUCTION Several years ago a series of waterflooding tests was made in the laboratory on a number of Woodbine core samples from the East Texas field. These samples had been stored in containers open to the air and were extracted with organic solvents before they were subjected to the laboratory tests. After water flooding, the residual saturation of kerosene, which was the oil used in the tests, was found to average about 30 per cent. This saturation was higher than expected. In investigating the circumstances which might have been responsible for such a high residual oil saturation, attention was given to possible changes in wetting properties of the rock brought about by the procedure employed in extracting the cores. Preliminary results indicated that the explanation for the high residual oil saturation lay in the wetting behavior of the cores, though what effect extraction had on this behavior was not clear. In consequence, the work described in this report was undertaken in an attempt to investigate the mechanism responsible, and to ascertain the actual residual oil saturation to be expected in the reservoir after water flooding. It was soon found that there were profound differcnces in the behavior of so-called "fresh cores" from the East Texas field and of the same cores after extraction with organic solvents. These differences were evident not only in the amount of residual oil left after water flooding, but also in the saturation of watet remaining in the core after displacement by oil. The complete explanation of this behavior is not yet apparent. The description of work and results described in following sections, therefore, must be considered as an interim report presenting facts which must await additional information before they can be fully interpreted.

Jan 1, 1956

By Jack White

This paper gives details of the results - of careful testing carried out on two types of ball mills, conical trunnion overflow and cylindrical grate discharge, on identical ore. The object of the test work was to determine which ball mill was the most economical to install for future extensions to the Mufulira concentrator.

Jan 1, 1950