Search Documents

By W. F. Vietti

Operations in the Texas Gulf Coast during the past year have resulted in the discovery of a number of new fields arid the extension of a few of the older fields, both by deeper drilling and by lateral development. Twenty-six new oil and gas-producing areas and discovery of oil or gas in three subsequently abandoned wells have been recorded for a total of 29 new fields of varying importance. Producing areas at Conroe, Manvel, Greta, Pierce Junction, Hastings, Dirks, Thompson, Batson, Mykawa, Tomball, Raccoon Bend, Samfordyce arid Saxct have been increased. Primary geologic studies followed by geophysical mapping or straight geophysical prospects have been responsible for the more important discoveries. These methods have further proved themselves an aid to limiting wildcatting to the more prospective areas and as the chief means to discover reserves in the future. Production for 1935 totaled 69,560,720 bbl. as compared with 60,850,-360 bbl. for 1934. Strict proration has been in force throughout the discovery of more oil than has been produced. The number of producing oil wells has steadily increased to 4851 at the end of 1935, as compared with 3858 at the end of 1934, owing in part to the prolonged life, because of proration. There were 1272 oil and gas wells completed during 1935, as against 835 in 1934. New Fields Pertinent data on the new fields discovered during 1935 are includrd in Tables 1 and 2. Hence, the discussion of these discoveries will be limited. Bee County.—Three new gas fields were added during the year: Beeville, discovered by G. M. Church in No. 1 Wood on Sept. 21; Foley, discovered by Dirks Bros. in No. 1 Foley on Feb. 8; and Plummer, discovered by Hynes and Fisher in No. 1 T. M. Plummer on Sept. 2. The three new oil fields added are: Hartzendorf, drilled on fee land by Hartzendorf and completed on May 17 as a small pumper; Ray, southwest of Tuleta, and discovered by Jameson and Burns in No. 1 Campbell

Jan 1, 1936

By B. L. Landrum, P. B. Crawford

Theoretical and potentiometric model studies have been made of the effect of non-uniform lateral permeabilities on pattern sweep efficiency and production capacity in waterflood and gas-cycling programs. It is shown that a diflerence in directional permeability by a factor of three may result in a sweep efficiency of only 43 per cent for a five-spot pattern or a sweep of either 79 or 38 per cent for a direct line-drive square pattern, depending on the direction of the line-drive flood. Changes in the pattern conductivity varied from about 0.8 to 1.34 over this same permeability variation, depending on the pattern used. It is suggested that measurements be made to determine the possible magnitude and extent of the directional permeability phenomenon early in the field developinent and certainly prior to the initiation of any fluid-injection progmm. INTRODUCTION Irregularities in reservoir sand properties long have been a major difficulty to anyone attempting to explicitly describe the field characteristics of oil production. In particular, it is well known that vertical and lateral permeabilities often differ appreciably; however, the existence of large regions with lateral permeabflity variation is not widely recognized. A number of years ago, extensive studies were conducted by the Secondary Recovery Research Labcratory of the Pennsylvania Grade Crude Oil Association, primarily on the Bradford field. Johnson and Hughes' reported a permeability trend in the northeast-southwest direction. They indicated that flow in the preferred direction may be 25 to 30 per cent greater in that direction than in the northwest-southeast direction. They also reported that similar effects may be found in other nearby fields. The origin of the permeability variation has been discussed by Griffith Hutchinson' described the results of labora- tory tests on limestone cores, pointing out that per-ferential directional permeabilities were significant in one-half of 10 formations studied and that the average permeability ratio was 16:1. Barfield, Jordan and Moore analyzed the fluid-injection displacement performance in the Spraberry and reported that the effective ratio of permeability parallel to the major axis to the permeability perpendicular to this axis was 144:l and that it inclined along an angle of about 30". To prevent the reduction of sweep efficiency which would normally result from flooding or cycling in such reservoirs, well spacing could be varied from the customary square to a diamond-shaped pattern. Johnson and Hughes' presented a method for determining the desired shape. Another method will be discussed in detail in the next section. It is the purpose of this paper to investigate quantitatively the effect of directional permeability upon the sweep efficiency and production capacity of the five-spot and line-drive well patterns. Information currently in the literature will be applied to this particular problem and augmented by a potentiometric model study. It is stressed that the effects herein discussed may or may not be of great importance because field data on this phenomenon are far too scant to form such an opinion. It is suggested that, if conditions similar to those found by Johnson and Hughes frequently exist (as may well be the case), more consideration cdrtainly should be given to this problem.

By Jos D. Weeks

On the extreme fringe of' the great Appalachian coal-basin is a long narrow detached coal-field, which is, in some respects, one of the most important in the United States. This field, about 90 miles long by 2½ to 16 miles wide, extends from the southwest corner of Somerset county, Pennsylvania, through Allegany and Garrett counties, Maryland, Mineral, Grant and Tucker counties, West Virginia, into Randolph county, West Virginia. In this distance four distinct sub-districts are recognized, the Wellersburg in Pennsylvania, the Cumberland-Georges creek in Maryland, and the Elk Garden and the Upper Potomac in West Virginia. The output of coal from the whole field including steam, domestic, smithing and coking-coal of the best quality, is about 4,500,000 tons annually. It is the nearest to tide-water of all the bituminous coal-fields which supply the great coal-markets of the Northern Atlantic seaboard ;

Jan 1, 1895

By O. J. Kensok

THE literature contains three previous studies of the chemical activities of Cd-Mg alloys: Trumbore, Wallace, and craigl obtained chemical activities of magnesium at 543" by performing electromotive-force measurements; Borg and irchenall calculated activities at 590°K based on vapor-pressure measurements of cadmium over Mg-Cd alloys by the Knud-sen effusion method; and Terpilouski and arcka measured the chemical activities of magnesium in the liquid state by means of electromotive-force measurements. In this study the vapor pressure of cadmium was determined over nine solid Cd-Mg alloys in the temperature range 571" to 697°K by the Knudsen effusion method. This study was prompted by the lack of precision in the data reported by Borg and Birchenall. Knudsen cells used during this study were fabricated from 0.020-in.-thick tantalum tubing. The tops and bottoms of the cells were cut from 0.010-in.-thick tantalum sheet, press-fitted, and welded in place. The orifice was drilled in the cell top and subsequently reamed to a knife-edge thickness. The diameter of the orifice was measured with a traveling microscope capable of reading 0.0001 cm. The sample was heated by means of a resistance

Jan 1, 1967

By D. T. Jones

In view of the importance of the application of scientific principles to the production of oil from the reservoir, the Production Staff of the Anglo-Iranian Oil Co. (late Anglo-Persian Oil Co.) has been engaged for some years on an intensive program of research on the physical properties of crude oil. Problems involving the retention of crude oil in capillaries and fine fissures demanded for their solution a knowledge of the surface tension and specific gravity of the crude under reservoir conditions, and it is the purpose of this paper to describe briefly the methods adopted for the determination of these properties, and to present the more important results. A detailed article was published in volume 1 of the World Congress Proceedings (1933). Surface-tension observations on crude oil regassed at high pressures with natural gases have been made in the past by Beecher and Park-hurstl and Swartz2, but up to the time of the investigations in Iran no one seems to have carried out experiments with gas-saturated crude direct from the reservoir and kept at its original pressure. Results obtained in this manner are obviously of greater practical value for solving problems connected with the reservoir. Method of Measurement No apparatus for the measurements, under the pressure conditions involved, was available, and a suitable instrument had to be designed and constructed in the Fields workshops. Careful consideration of the matter led to the adoption of a method for measuring the surface tension which did not involve a knowledge of the specific gravity of the oils under the working conditions: the main reason for this being that up to that time no accurate determination of the specific gravity had been made under these conditions. The method adopted involves the measurement of the actual tension in an oil film, and is effected by means of

Jan 1, 1936

By D. T. Jones

In view of the importance of the application of scientific principles to the production of oil from the reservoir, the Production Staff of the Anglo-Iranian Oil Co. (late Anglo-Persian Oil Co.) has been engaged for some years on an intensive program of research on the physical properties of crude oil. Problems involving the retention of crude oil in capillaries and fine fissures demanded for their solution a knowledge of the surface tension and specific gravity of the crude under reservoir conditions, and it is the purpose of this paper to describe briefly the methods adopted for the determination of these properties, and to present the more important results. A detailed article was published in volume 1 of the World Congress Proceedings (1933). Surface-tension observations on crude oil regassed at high pressures with natural gases have been made in the past by Beecher and Park-hurstl and Swartz2, but up to the time of the investigations in Iran no one seems to have carried out experiments with gas-saturated crude direct from the reservoir and kept at its original pressure. Results obtained in this manner are obviously of greater practical value for solving problems connected with the reservoir. Method of Measurement No apparatus for the measurements, under the pressure conditions involved, was available, and a suitable instrument had to be designed and constructed in the Fields workshops. Careful consideration of the matter led to the adoption of a method for measuring the surface tension which did not involve a knowledge of the specific gravity of the oils under the working conditions: the main reason for this being that up to that time no accurate determination of the specific gravity had been made under these conditions. The method adopted involves the measurement of the actual tension in an oil film, and is effected by means of

Jan 1, 1936

By E. C. Houston

The presence in the Tennessee Valley of extensive deposits of olivine, a silicate of magnesium and iron that contains approximately 28 per cent magnesium, has been recognized since 1896 when Lewis8 published a survey of basic magnesium rocks of western North Carolina. A recent field survey by T.V.A.7 showed that more than two hundred million tons of high-grade olivine occurs above local drainage levels in western North Carolina and northern Georgia. Except for sporadic attempts to work the olivine for its nickel and chromium contents,10 the ore received little attention industrially until 1926 when Goldschmidt3 suggested its use in the manufacture of refractories. Only one instance is recorded of an attempt to utilize the ore commercially for its magnesium content;" in this case a process was used in which olivine was treated with sulphuric acid, the resultant mixture was leached with water, and the leach solution was purified and evaporated to form epsom salts, which was the end product. As a part of its program of contributing to the development of the natural resources of the region, the Tennessee Valley Authority became interested in the olivine deposits as a source of metallic magnesium because of their high magnesium content and proximity to hydroelectric power. Studies were undertaken to determine the feasibility of producing magnesium chloride by extraction of olivine. The experimental work was carried out successively at the T.V.A. Minerals Testing Laboratory, Norris, Tenn., at the Georgia State Engineering Station,* Atlanta, Ga., and at the T.V.A. laboratory at Wilson Dam, Ala. The present paper describes a process. developed through the pilot-plant stage, whereby magnesium chloride suitable for reduction to metallic magnesium can be prepared from olivine by extraction with hydrochloric acid and subsequent purification. Research on the magnesium-from-olivine process, originally intended for peacetime use, was given impetus by the shortage of magnesium that existed at the beginning of the current world war. By the time the process was sufficiently developed to justify a proposal for its inclusion in the war program, the shortage had been met by expansion and development of other processes. However, it is believed that the magnesium-from-olivine process may have advantages that will warrant consideration of its use after the war, when the economics of the various processes rather than production on a wartime scale will be the criterion for commercial production of magnesium. Description OF Process Metallic magnesium is produced electro-lytically by the Dow and the Elektron

Jan 1, 1949

By E. Topanelian

In recent years considerable progress has been made in the development and application of mathematical techniques for the solution of certain problems involving economic "strategies". Such a problem might involve, for example, the scheduling of shipments of a commodity from a number of sources to a number of destinations. The object would be to schedule the shipments in a manner so as to satisfy the destination requirements and at the same time minimize the transportation costs. The solution to such a problem is not necessarily intuitively obvious. The "obvious" solution is frequently far from optimum. If the shipments are to be made from, for example, only two sources to four destinations, the optimum schedule is readily found. However, if shipments are to be made from, say, 10 sources to several hundred destinations, even a competent and experienced scheduler may spend considerable time in finding a reasonable answer. Even then he is not sure that he has the optimum solution. Furthermore, he has no way of knowing how far from optimum the answer is. Consequently, he does not know whether he should accept this solution or seek a better one. Prior to the advent of large high-speed digital computers, little more could be done with such problems because of their great size and multiplicity of possible solutions. A problem involving 20 sources and 50 destinations would require choosing, from a very large number of possible combinations, the optimum combination of 1,000 variables. The best one could do was to utilize intuition, extrapolation from past experience, and other non-exact approaches. With a high-speed computer, however, such problems can be solved providing a reasonable computational procedure (or algorithm) can be utilized. The purpose of this paper is to describe such a procedure (linear programming) and to apply this procedure to a production scheduling problem. THE RESERVOIR PROBLEM A simple reservoir model is used throughout this analysis to illustrate the use of linear programming. Even the simplest reservoir behavior problem is nonlinear in both space and time, but if the geometry is fixed for a particular study and the time variable is quantized, the resultant system may be described by linear constraints on the variable production rates. Crude oil is available from five separate sources and is delivered to a pipeline. Sources 1, 2, 3 and 4 are ideal reservoirs and therefore are subjected to reservoir flow restrictions. Source 5 is labeled "Outside Source" and crude oil from this source is assumed to be available in unlimited quantities without considering reservoir conditions. The general problem is to determine the schedule of crude oil production from five sources which, over an eight-year period and subject to certain restrictions, will result in maximum profit. "Profit" is defined to encompass all economic factors and expenses involved in producing and selling crude oil to a pipeline facility. Such economic factors are lumped to the extent that the term represents the dollars profit from one barrel of crude oil from any of the five sources entering the pipeline system. Table 1 presents the assumed profit per barrel for oil from any of the five sources over each of the four time periods. In this chart the eight years is broken into four equal intervals of two years. The selection of four time periods of two years each and the values representing the potential profit are completely arbitrary selections for the purpose of illustrating this idealized reservoir problem. In any practical application of this work a careful economic study would have to be made in order to estimate potential unit profits for time periods as far in the future as eight years. In this particular study it is assumed that all of the potential unit profits (C) are known and fixed before the production schedule is attempted. For each reservoir arbitrary values are assigned for

By A. H. Daane, W. J. Wunderlin, B. J. Beaudry

The solid solubility of holmium in copper, silver, and gold, determined using metallographic techniques, was found to be a maximum of 0.06, 2.4, and 3.2 wt pct, respectively, nt the eutectic temperatures. The temperatures of these eutectic horizontals, determined by differential thermal analysis, were found to be 868", 787", and 778"C, respectively. The first compound on the silver-rich side of the Ag-Ho system was found to be A&Ho2. In a study by Gold et al.,' on the effect of small amounts of soluble impurities on the electrical resistance and thermoelectrical properties of copper, traces of iron were shown to have drastic effects on the thermoelectric power due to the magnetic scattering of the conduction electrons. Since little is known about the state of the iron ion when dissolved in copper, Gold had hoped to repeat these experiments using certain rare earths as the magnetic scattering centers; because of the tightly bound 4f electrons it is not expected that their spectroscopic state would be affected by alloying. In such an experiment the sole role of the trace rare-earth impurity would be to magnetically scatter the copper conduction electrons without producing appreciable distortions in the otherwise pure copper matrix. Since holmium was chosen for such a study because of its high magnetic moment, it was necessary to establish precisely its solid solubility in copper. The study was extended to include the solvents silver and gold, so that an evaluation of the data using classical solubility parameters could be made. No previously reported work on the systems of holmium with copper, silver, or gold was found in the literature. Information on the solubility of other rare earths in these three metals is also very meager. The solubility limit of yttrium in copper was reported as less than 1 wt pct2 and the solubility of praseodymium in gold as 0.35 wt pct,3 while no references were found on solubility studies of rare earths in silver. EXPERIMENTAL Materials. The materials used in this investigation were distilled holmium prepared in this Laboratory, OFHC* copper, electrorefined silver (99.9 *OFHC = oxygen-free high conductivity. pct), and gold with the analyses given in Table I. Sample Preparation. Samples weighing 1 to 2 g were prepared by arc-melting the components together on a water-cooled copper plate under purified argon atmosphere. The samples, turned and remelted at least five times to ensure homogeneity, showed weight changes of less than 0.1 wt pct after melting. Samples containing less than 0.7 wt pct Ho were prepared by diluting 1 to 2 wt pct Ho alloys with the pure solvent, while samples with concentrations greater than 0.7 wt pct Ho were prepared directly from the metals. The samples were wrapped in tantalum foil, sealed in outgassed Vycor tubing under helium, annealed at the desired temperature for at least 24 hr, and then quenched by shattering the Vycor tube in cold water. Metallographic Methods. Standard mechanical polishing methods were used in preparing the silver and gold alloys for examination, while the copper alloys were electropolished using a 40 pct solution

Jan 1, 1963

By W. B. Hincke, C. G. Maier

Commercial processes of lead softening directly involve the behavior on fusion of mixtures of the oxides of antimony and lead, and the vapor pressures of these materials. Practically no quantitative data have been available for the discussion of lead softening from the point of view of the fundamental metallurgy of the process. The Pacific Experiment Station of the United States Bureau of Mines, in cooperation with the University of California, in the course of its program of study of the fundamental properties of oxides and sulfides, recently made vapor pressure measurements upon the various forms of pure antimony trioxide.1 When these measurements were considered in connection with the softening and "fuming" furnaces which are often used for lead purification, an unexpectedly anomalous condition appeared. In brief, this anomaly consisted in the fact that in certain softening furnaces, where lead bullion of approximately 1 per cent antimony content was being treated at a temperature of approximately 1300" F., no appreciable volatilization of antimony occurred, there being produced only a "skim" containing from 15 to 20 per cent Sb, 65 to 60 per cent Pb, as mixed oxides. In the "fuming furnaces," where the temperature was only about 1400" F. and where an accumulation of "skims" from the primary softener was being treated with certain other antimony-containing materials, a considerable volatilization of antimony as oxide occurred; an "impure" skim of some 60 to 65 per cent Sb and 10 per cent Pb was also produced as mixed oxides. The latter material cannot be suitably treated in hearth-type or softener furnaces. The essential chemical difference between the first and second step is the customary use of some reducing material (such as petroleum coke) in the later operation. An obvious interpretation of the effect of coke in facilitating the fuming of the antimony is the supposition that the antimony may be reduced to metal, and volatilized as such. This supposition is improbable, however, when it is realized that a slight extrapolation of the vapor-

Jan 1, 1932

By R. C. Buehl, M. B. Royer

High manganese slags of low phosphorus and iron content are produced by air oxidation of high phosphorus spiegeleisen in a basic-lined converter. Control of phosphorus and iron within specification limits for ferromanganese ore feed is obtained by a unique cyclic operating procedure. Various types of slags, or synthetic manganese ore, can be made. AN affiliated paper' describes the production of high phosphorus spiegeleisen containing 14 to 23 pct Mn and up to 4 pct P in an experimental blast furnace from open-hearth slag or manganiferous iron ore. This phosphorus content is too high for use of the spiegel in normal steel-production operations. Consequently, a preferential separation must be effected whereby the manganese is concentrated in a product that is usable in industrial operations. The preferential separation methods being investigated for this phase of the work are confined to pyrometal-lurgical processes for ready incorporation into steel-plant operations. It is fortunate that manganese is more actively oxidizable than iron or phosphorus, and therein lies a preferential separation method for isolating manganese from these two elements. Silicon is more strongly oxidizable than manganese, and its oxidation precedes, or occurs simultaneously, with manganese. Therefore, manganese and silicon are separable into a high manganese oxide slag phase while the phosphorus and iron remain in the molten metallic state. Complete separation of these elements represents an ideal condition which is not generally attainable in actual operations. This pyro-metallurgical method for separating manganese from phosphorus and iron by preferential oxidation was investigated by blowing 500 lb of metal in a basic-lined vessel to obtain preliminary information on the effectiveness of the procedure. Certain conditions of attainment in the separation process are desirable in any method for removing manganese from high phosphorus spiegeleisen, such as: 1—High recovery of manganese in the oxidation product; 2—the product to be of equal or better quality than ferromanganese-grade ore—48 pct Mn minimum, less than 10 pct SiO2, and Mn-P ratio of 300:1; and 3—attainment of the enumerated objectives in a product amenable to industrial handling, such as a slag of high manganese content that will flow from the processing vessel and of sufficient fluidity for ready separation of metallic granules that may have become mixed with the manganese slag phase. Previous Work Recovery of manganese from low grade ores and industrial byproduct slags by smelting to spiegeleisen, with subsequent oxidation to synthetic ferro-manganese-feed ores, has been a subject for periodic investigation during the past four or five decades in the United States and Germany. Joseph' and associates of the Bureau of Mines North Central Experiment Station, Minneapolis, Minn., smelted manganiferous iron ores of the Cuyuna range, Minn., to spiegeleisen and subsequently tried air and ore oxidation procedures for concentrating the manganese into synthetic ferrograde manganese ore. Joseph's results on the operation of a side-blown basic-lined converter for air oxidation of manganese from molten spiegeleisen were so discouraging that the procedure was abandoned after 11 blowing tests. Much slag was thrown from the converter vessel; phosphorus content was four to five times the maximum allowable for ferro ore; and a manganese-iron ratio of only 2 or 3:1 was obtained in the slag instead of the required 8:1. Oxidation of manganese from spiegeleisen with about 0.5 pct P, by adding iron ore to molten spiegel in an experimental open-hearth furnace, proved moderately successful in Joseph's experiments. The main drawback to the operation was the necessity for over-oreing for effective oxidation of the manganese with consequent too high iron oxide residual in the slag. Furthermore, the phosphorus content was proportional to the iron concentration and therefore much too high, so that several hours of reduction by a carbonaceous material were required to adjust the iron and phosphorus to the desired content of high grade ferro feed. A troublesome feature of the slag product of the spiegel oxidation process was its lack of fluidity if the silica content was less than 10 pct, the concentration considered desirable for the synthetic ore. Approximately twice the desired concentration of silica was required to impart enough fluidity for transfer from the vessel by pouring. The acute shortage of manganese in Germany

Jan 1, 1953

By M. Hall, Y. P. Chugh, A. Okunola

Effects of moisture absorption on the behavior of the Dykersburg shale overlying Harrisburg coal seam in Southern Illinois are presented in this paper. Cylindrical samples of the shale 2.5 cm in diameter and 5.0 cm long were studied for weight gain and swelling strains at 90, 95, and 100 percent relative humidity and under immersed water conditions. After attaining equilibrium conditions, the samples were studied for changes in the strength and deformation behavior. The depth of moisture penetration was measured using the Vickers microhardness measurements. Using the basic mass transfer concepts, effective diffusion coefficients were computed for the shale.

Jan 1, 1981

THE object of all classification is to group together things which are alike, and separate those which are unlike. This object is essentially a practical one, enabling us to apply past experience to new conditions: Many costly large-scale experiments lose half their importance for want of proper description of the coal used, and the consequent impossibility of predicting other coals will behave in the same way. I do not, therefore, make a fundamental distinction between "scientific" and "use" classifications, except in so far as use depends on conditions, such as size or impurities which are not related to the nature of the coal substance itself. The characters chosen to define the classes of coal must be such as are accompanied by as many other properties as possible. It is not to be expected that any system of classification will enable us to predict every property of coal, since all specimens have an individuality of their own. But specimens can be grouped by a number of resemblances into species. Further, species which resemble each other can be grouped into genera.

Jan 1, 1928

By Otto Wartenweiler

After the phenomenal development of the new mine, the United Eastern Mining Co., with Mr. Frank A. Keith as President, decided to install a reduction plant. The character of the ore, closely resembling the product of other mines in the district, did not offer any particular metallurgical problems, since these neighboring mines had been operating milling plants very successfully for several years. Thus, with the general metallurgical treatment fairly well-defined, the matter of next importance was to design and construct a plant as economically as possible, that would give the best results obtainable. The ore consists of a mixture of calcite and quartz in about equal quantities, with some decomposed andesite, while the average value of mill feed was calculated to be $20 or more in gold, no silver being present. The tonnage to be treated at the start was fixed at 200 tons, but, in view of the favorable condition of the mine, it was considered advisable to arrange facilities for increasing the capacity to 400 tons. While it is best in some cases to adopt a distinct independent unit system where future enlargement is contemplated, in this instance the plans worked out differently. Summarized, the treatment adopted consists of coarse crushing, coarse grinding, fine grinding and cyanidation. For coarse crushing the selection of the No. 6 size gyratory crusher was governed not so much by its capacity as by the size of the feed openings to receive the run-of-mine material, which was too coarse for a No. 5 crusher. TO accomplish the coarse grinding to best advantage, a careful comparison was made between the modern steel ball-mill—the last word in crushing and grinding—and one of its older, and, at that time better-established, competitors, the rolls. The following conclusion was reached: While it is possible that for the sized plant under consideration the cost of operating rolls might be a little cheaper, it is preferable to use ball-mills because a simpler arrangement is possible, and because the handling of ball-mills is preferred by the operator. A marked departure was introduced for fine grinding. Instead of the long type of tube-mill, using pebbles, a mill of similar design was selected, but of much shorter length, using small cast-steel balls as grinding medium. For cyanidation, the Dorr continuous countercurrent process was

Jan 1, 1918

By W. R. Purcell

An apparatus is described whereby capillary pressure curves for porous media may be determined by a technique that involves forcing mercury under pressure into the evacuated pores of solids. The data so obtained are compared with capillary pressure curves determined by the porous diaphragm method, and the advantages of the mercury injection method are stated. Based upon a simplified working hypothesis, an equation is derived to show the relationship of the permeability of a porous medium to its porosity and capillary pressure curve, and experimental data are presented to support its validity. A procedure is outlined whereby an estimate of the permeability of drill cuttings may be made with sufficient acuracy to meet most engineering requirements. INTRODUCTION The nature of capillary pressures and the role they play in reservoir behavior have been lucidly discussed by Lev-rett', Hassler, Brunner, and Deah12, and others. As a result of these publications the value of determining capillary pressure curves for cores has come to be generally recognized within the oil industry. While considerable attention has been directed toward the subject in an effort to provide a reliable method of estimating percentages of connate water, it has been recognized that capillary pressure data may prove of value in other equally important applications. This paper describes a method and procedure for determining capillary pressure curves for porous media wherein mercury is forced under pressure into the evacuated pores of the solids. The pressure-volume relationships ob- tained are reasonably similar to capillary pressure curves determined by the generally accepted porous diaphragm method. The advantages of the method lie in the rapidity with which the experimental data can be obtained and in the fact that small, irregularly shaped samples, e.g., drill cuttings, can be handled in the same manner as larger pieces of regular shape such as cores or permeability plugs. Based upon a simplified working hypothesis, a theoretical equation will be derived which relates the capillary pressure curve to the porosity and permeability of a porous solid, and experimental data will be presented to support its validity. This relationship aplied to capillary pressure data obtained for drill cuttings by the procedure described provides a means for predicting the permeability of drill cuttings. METHODS FOR DETERMINING CAPILLARY PRESSURES Several techniques have so far been employed in determining capillary pressure curves and these fall into two principal categories: (1) Liquid is removed from, or imbibed by, the core through the medium of a high displacement pressure porous diaphragm (2) Liquid is removed from the core which is subjected to high centrifugal forces in a centrifuge4,'. There are? however, certain limitations inherent in both methods. The greatest capillary pressure which can be observed by method (I), above, is determined by the maximum displacement pressure procurable in a permeable diaphragm which at the present time appears to be less than 100 psi. An even more serious limitation of the diaphragm method is imposed hy the fact that several days may be required to reach saturation equilibrium at a given pressure; hence, the time re- quired to obtain a well-defined curve may be measured in terms of weeks. Furthermore, to date, no suitable technique for handling relatively small, irregularly shaped pieces of rock, such as drill cuttings, has been reported and, therefore, measurements must be made, in general, on cores, or portions thereof. The centrifuge method offers the distinct advantage over the porous diaphragm method of arriving at saturation equilibrium in a relatively short time by virtue of the elimination of the transfer medium for the liquid. The calculation of capillary pressures from centrifuge speeds is somewhat tediousa, however, and the equipment required is fairly elaborate. While there exists the possibility that this method might be adaptable to the determination of the capillary pressures of cuttings, this particular ramification has not been investigated, as far as is known. In view of the limitations of the two principal methods for determining capillary pressures, the apparatus described in the following sections has been devised in order that difficulties previously encountered might be circumvented. MERCURY INJECTION METHOD FOR DETERMINING CAPILLARY PRESSURES Theory The methods described above for determining capillary pressures are characterized by the fact that one of the fluids present within the pore spaces of the solid is a liquid which "wets" the solid, i.e., the contact angle which the liquid forms against the solid is less than 90" as measured through that phase. For these "wetting" liquids the action of surface forces is such that the fluid spontaneously fills the voids within the solid. These forces likewise oppose the withdrawal of the fluid from the pores of the solid.

Jan 1, 1949

By W. R. Purcell

An apparatus is described whereby capillary pressure curves for porous media may be determined by a technique that involves forcing mercury under pressure into the evacuated pores of solids. The data so obtained are compared with capillary pressure curves determined by the porous diaphragm method, and the advantages of the mercury injection method are stated. Based upon a simplified working hypothesis, an equation is derived to show the relationship of the permeability of a porous medium to its porosity and capillary pressure curve, and experimental data are presented to support its validity. A procedure is outlined whereby an estimate of the permeability of drill cuttings may be made with sufficient acuracy to meet most engineering requirements. INTRODUCTION The nature of capillary pressures and the role they play in reservoir behavior have been lucidly discussed by Lev-rett', Hassler, Brunner, and Deah12, and others. As a result of these publications the value of determining capillary pressure curves for cores has come to be generally recognized within the oil industry. While considerable attention has been directed toward the subject in an effort to provide a reliable method of estimating percentages of connate water, it has been recognized that capillary pressure data may prove of value in other equally important applications. This paper describes a method and procedure for determining capillary pressure curves for porous media wherein mercury is forced under pressure into the evacuated pores of the solids. The pressure-volume relationships ob- tained are reasonably similar to capillary pressure curves determined by the generally accepted porous diaphragm method. The advantages of the method lie in the rapidity with which the experimental data can be obtained and in the fact that small, irregularly shaped samples, e.g., drill cuttings, can be handled in the same manner as larger pieces of regular shape such as cores or permeability plugs. Based upon a simplified working hypothesis, a theoretical equation will be derived which relates the capillary pressure curve to the porosity and permeability of a porous solid, and experimental data will be presented to support its validity. This relationship aplied to capillary pressure data obtained for drill cuttings by the procedure described provides a means for predicting the permeability of drill cuttings. METHODS FOR DETERMINING CAPILLARY PRESSURES Several techniques have so far been employed in determining capillary pressure curves and these fall into two principal categories: (1) Liquid is removed from, or imbibed by, the core through the medium of a high displacement pressure porous diaphragm (2) Liquid is removed from the core which is subjected to high centrifugal forces in a centrifuge4,'. There are? however, certain limitations inherent in both methods. The greatest capillary pressure which can be observed by method (I), above, is determined by the maximum displacement pressure procurable in a permeable diaphragm which at the present time appears to be less than 100 psi. An even more serious limitation of the diaphragm method is imposed hy the fact that several days may be required to reach saturation equilibrium at a given pressure; hence, the time re- quired to obtain a well-defined curve may be measured in terms of weeks. Furthermore, to date, no suitable technique for handling relatively small, irregularly shaped pieces of rock, such as drill cuttings, has been reported and, therefore, measurements must be made, in general, on cores, or portions thereof. The centrifuge method offers the distinct advantage over the porous diaphragm method of arriving at saturation equilibrium in a relatively short time by virtue of the elimination of the transfer medium for the liquid. The calculation of capillary pressures from centrifuge speeds is somewhat tediousa, however, and the equipment required is fairly elaborate. While there exists the possibility that this method might be adaptable to the determination of the capillary pressures of cuttings, this particular ramification has not been investigated, as far as is known. In view of the limitations of the two principal methods for determining capillary pressures, the apparatus described in the following sections has been devised in order that difficulties previously encountered might be circumvented. MERCURY INJECTION METHOD FOR DETERMINING CAPILLARY PRESSURES Theory The methods described above for determining capillary pressures are characterized by the fact that one of the fluids present within the pore spaces of the solid is a liquid which "wets" the solid, i.e., the contact angle which the liquid forms against the solid is less than 90" as measured through that phase. For these "wetting" liquids the action of surface forces is such that the fluid spontaneously fills the voids within the solid. These forces likewise oppose the withdrawal of the fluid from the pores of the solid.

Jan 1, 1949

By C. L. Mantell

Although so common and well known a metal, tin is really a less abundant element than many of those less familiar and usually ranked with the scarce or rare elements, such as cerium, yttrium, lithium, beryllium, titanium, zirconium and vanadium. The color of tin is white, with a slightly bluish tinge. When it is compared with nickel, the latter metal is brown. When placed alongside of tin, chromium is definitely blue. Tin is whiter than silver or zinc. Exceedingly thin films of tin show various shades of brown by transmitted light. The metal has a brilliant luster, and when mirror-polished, has high light reflectivity. The luster depends to a large extent upon the pouring temperature at which the metal is cast. If the temperature be too high, iridescent colors may show on the surface. These are the result of oxide film formation. If the pouring temperature be too low, the surface is dull. Small amounts of foreign metals, such as lead, arsenic, antimony and iron, decrease the luster of tin and impart a yellowish tinge to the metal. The structure is decidedly crystalline. The cast metal is a mass of crystals. When a bar of tin is bent, it emits a characteristic creaking sound. This is called the "cry" of tin, resulting from the grinding of the crystals one against the other during the bending of the metal. Tin metal may lose its crystalline structure by cold working, but grain growth occurs rapidly under the influence of heat. Metal which has been cast at a low temperature may become amorphous as the result of mechanical work. If such material be heated to temperatures well below the melting point, say at 110° C. for a half hour or for a few minutes at 150" C. recrystallization occurs. If the surface of tinned plate, tin foil, or tin meta1 in cast form be etched with hydrochloric acid containing a little free chlorine, attack occurs at the intererystalline faces. The surface shows patterns resembling the frost flowers on window panes in winter. The etched appearance is called moire metallique. Fine dendritic surface crystals of tin may be obtained by casting the metal on a surface of polished steel. In commercial tin plate, the intercrystalline boundaries are shown by fine grooves or channels, .which result from the method

Jan 1, 1929

By C. L. Mantell

Although so common and well known a metal, tin is really a less abundant element than many of those less familiar and usually ranked with the scarce or rare elements, such as cerium, yttrium, lithium, beryllium, titanium, zirconium and vanadium. The color of tin is white, with a slightly bluish tinge. When it is compared with nickel, the latter metal is brown. When placed alongside of tin, chromium is definitely blue. Tin is whiter than silver or zinc. Exceedingly thin films of tin show various shades of brown by transmitted light. The metal has a brilliant luster, and when mirror-polished, has high light reflectivity. The luster depends to a large extent upon the pouring temperature at which the metal is cast. If the temperature be too high, iridescent colors may show on the surface. These are the result of oxide film formation. If the pouring temperature be too low, the surface is dull. Small amounts of foreign metals, such as lead, arsenic, antimony and iron, decrease the luster of tin and impart a yellowish tinge to the metal. The structure is decidedly crystalline. The cast metal is a mass of crystals. When a bar of tin is bent, it emits a characteristic creaking sound. This is called the "cry" of tin, resulting from the grinding of the crystals one against the other during the bending of the metal. Tin metal may lose its crystalline structure by cold working, but grain growth occurs rapidly under the influence of heat. Metal which has been cast at a low temperature may become amorphous as the result of mechanical work. If such material be heated to temperatures well below the melting point, say at 110° C. for a half hour or for a few minutes at 150" C. recrystallization occurs. If the surface of tinned plate, tin foil, or tin meta1 in cast form be etched with hydrochloric acid containing a little free chlorine, attack occurs at the intererystalline faces. The surface shows patterns resembling the frost flowers on window panes in winter. The etched appearance is called moire metallique. Fine dendritic surface crystals of tin may be obtained by casting the metal on a surface of polished steel. In commercial tin plate, the intercrystalline boundaries are shown by fine grooves or channels, .which result from the method

Jan 1, 1929

By L. S. Darken

In the study of reactions occurring in liquid iron, alone or in contact with a liquid oxide or slag phase, it has been found that the experimental data over a limited range of concentration can in some cases be represented satisfactorily by the simple equilibrium expression where (P) denotes the concentration of a product and (R) the concentration of a reactant in the reaction r1R1 + r2R2 + • • • D P lP1 + P 2P2 + • • • Some of the reactions for which it holds are listed in Table 1. For others, however, the simple equation apparently does not hold. This has been attributed to an improper method of expressing concentration (for instance, weight per cent instead of mol fraction); or it has been supposed that the solutions are not ideal in the sense that the activity of a component is not proportional to its true mol fraction. But it may be that the problem has been oversimplified by neglecting some molecular species actually present; that is, by considering only the ostensible simple components and thus leaving out of account possible compound formation. It is the purpose of the present paper to point out how, in a group of related cases, a reasonable consistent assumption relative to the presence of a compound makes it possible to express the experimental data satisfactorily by the simple equilibrium expression when this compound is taken into account, and to bring into harmony data referring to different reactions in liquid iron. There are several a priori reasons for believing that solutions in liquid iron should not deviate far from ideality, provided that the concentration of solute is not too great and is expressed in proper terms. The factors that commonly lead to nonideality in systems at ordinary temperature— as ionization or the occurrence of polar and nonpolar molecules—are presumably less effective in inetal and in slag systems at high temperature. Again, the type of equation commonly used to express the value of

Jan 1, 1940

By L. S. Darken

In the study of reactions occurring in liquid iron, alone or in contact with a liquid oxide or slag phase, it has been found that the experimental data over a limited range of concentration can in some cases be represented satisfactorily by the simple equilibrium expression where (P) denotes the concentration of a product and (R) the concentration of a reactant in the reaction r1R1 + r2R2 + • • • D P lP1 + P 2P2 + • • • Some of the reactions for which it holds are listed in Table 1. For others, however, the simple equation apparently does not hold. This has been attributed to an improper method of expressing concentration (for instance, weight per cent instead of mol fraction); or it has been supposed that the solutions are not ideal in the sense that the activity of a component is not proportional to its true mol fraction. But it may be that the problem has been oversimplified by neglecting some molecular species actually present; that is, by considering only the ostensible simple components and thus leaving out of account possible compound formation. It is the purpose of the present paper to point out how, in a group of related cases, a reasonable consistent assumption relative to the presence of a compound makes it possible to express the experimental data satisfactorily by the simple equilibrium expression when this compound is taken into account, and to bring into harmony data referring to different reactions in liquid iron. There are several a priori reasons for believing that solutions in liquid iron should not deviate far from ideality, provided that the concentration of solute is not too great and is expressed in proper terms. The factors that commonly lead to nonideality in systems at ordinary temperature— as ionization or the occurrence of polar and nonpolar molecules—are presumably less effective in inetal and in slag systems at high temperature. Again, the type of equation commonly used to express the value of

Jan 1, 1940