Search Documents

By Fred Wise, C. W. Wark

The Getchell mine, a comparatively recent gold discovery, is in the old Potosi mining district, Humboldt County, Nevada. All ore is mined from open pits using Diesel shovels and gasoline trucks. Two types of ore are mined, oxide and sulphide. Oxide ores are siliceous or shaly; sulphide ores either gougy, siliceous or shaly. In mining, the sulphide ore is segregated into hard and gougy ore, because the gouge must be dried before it can be crushed. The oxide ore is not segregated. General Metallurgy The oxide ore is the leached outcrop that overlies the sulphide ore body. All of the iron and arsenic sulphides found in the sulphide ores have been thoroughly oxidized. The sulphur and arsenic have been leached out while the iron is present as hematite and limonite. The oxide ore is amenable to direct cyanidation, and although no visible free gold is present it is released at a comparatively coarse grind. The sulphide ore is more refractory, since the gold is all of micron size and some of it is locked in fine sulphides. It has been established microscopically that the free gold is coated with an impervious shell, which is probably some form of iron compound. The sulphide ores contain from 1.5 to 2 per cent of arsenic, which is present as orpiment and realgar with minor amounts of arsenopyrite. The orpiment and realgar are of a later mineralization than the gold and are barren. Roasting and washing of the sulphide ore prior to cyanidation is necessary to eliminate , the arsenic, to alter the gold coating from an insoluble form to a soluble form, and to release the gold associated with the fine sulphides. Washing the ground calcine in weak sulphuric acid, trona, or hot water are beneficial in the order named, but to date the water is the best from an economic standpoint. Metallurgical tests as well as plant practice indicate that a certain amount of gold cannot be recovered even by going beyond economic practices. On this basis metallurgical results are viewed in the light of an optimum tailing rather than a percentage of extraction. Milling Practice Crushing (Fig. I).—There are three primary ore bins, one each for oxide ore, gougy sulphide ore, and hard sulphide ore. In front of each bin a substantial yard is maintained, which makes it possible to Stockpile 2500 tons of oxidized ore, 1000 tons of hard sulphide ore, and 1000 tons of gougy sulphide ore. The bins are fed by a 60-hp. caterpillar bulldozer from the stockpiles. Fig. I shows the method and

Jan 1, 1943

By Joseph P. Lyden

In the Picher field, structure made openings for the circulation of the mineralizing solutions by flexing, shearing, and fracturing the sedimentary beds. This structure is used with the spatial and genetic relationship of the ore minerals, sphalerite and galena, and the gangue minerals, dolomite and jasperoid, in prospecting for ore bodies.

Jan 12, 1950

By Arthur B. Yates

Diamond drilling has advanced and expanded during the past few yean. Along with this increase there has been a marked trend to rely more and more upon drilling for the outlining of ore for reserve purposes. This is especially true underground, where men have not been available for opening up ore by crosscuts, drifts and raises. During the recent heavy call upon known ore reserves, more drilling has been done for exploration and it has become expedient to drill longer lateral holes from underground and deeper holes both from surface and from exploration headings in the mines. Furthermore, these deeper holes have to be drilled closely enough to warrant calculation of "probable" if not "proven" ore, from the results obtained therefrom. Interpretation of diamond-drill results has become more precise and reliable with the growing knowledge and understanding of the geologic structures that control the geometry of ore distribution, and this has broadened the field of usefulness of the drill. All of this has created a necessity and a demand for more accurate control of the hole as to direction, a more precise and reliable method of surveying for position, and a need for better and more complete core recovery, as well as larger cores, to provide an adequate sample. At depth the control becomes more difficult and, at the same time, more important. Control A close study of drilling in various parts of the world for a period of more than 20 years has brought to light one definite rule, practically invariable; namely, that diamond-drill holes tend to deviate into a position normal to any structure existing in the rocks, such as bedding, schistosity, gneissosity, or even parting or jointing— even if the hole is started at almost any angle other than parallel with the structure. It also appears that the better developed the structure is, the more quickly will the hole get into a position perpendicular to it. It has often been said that there is a tendency for holes to "drift" in the direction of rotation. This is obviously untrue, for in a vertical hole the measure of deviation would depend upon the azimuth chosen as zero, and there is an infinite number of choices. It has been proved. however, that in homogeneous rocks there is a tendency for the hole to corkscrew, and that the direction of the spiral is the same as the direction of rotation. This may account for the belief that holes drift in that direction. Some tests have been made using right-hand and left-hand rods, and these show that no matter what the direction of rotation the hole will swing into a position perpendicular to the structure. Methods of Control The foregoing empirical rule may be used as an indirect method of control. If the prevailing structure is known, it may be advantageous to start the hole as nearly normal to it as possible, for the

Jan 1, 1946

By D. J. Carney, J. Chipman, N. J. Grant

SINCE the beginning of this century it has been known that hydrogen contributes to the porosity of steel and that it is harmful to its mechanical properties. The evidence for this has been largely qualitative. Steel to which hydrogen was purposely added. in sufficient .amounts was shown to be either porous or brittle or both, whereas similar steel of low hydrogen content was shown to be free of porosity and to possess normal physical properties. There have been a considerable number of qualitative experiments of this type. Also, early in this century, a few attempts were made to measure the amount of hydrogen normally dissolved in commercial steels. This was usually done by placing the sample under an inverted liquid column such as mercury and collecting the evolved gas. These attempts, while not successful in measuring actual amounts of dissolved hydrogen gas, were able to prove that this gas will diffuse out of steel at room temperature, and that the amount of hydrogen dissolved is normally very small. On the basis of such qualitative evidence, hydrogen has been and still is blamed for a great number of the troubles encountered in the steel industry. In recent years, partial solutions for many steel-working problems have been obtained. These have led to increased interest in accurate quantitative work on hydrogen in steel, with the expectation that the results might possibly answer a few of the remaining unsolved problems. Commercially, two of the obvious questions which are in need of an answer are: (1) what are the most important sources of hydrogen, and (2) what quantity of hydrogen can be tolerated in various steels? There are many other unanswered questions. To begin to find the answers it seemed logical to start at the beginning of steel production with the liquid metal. Further, it seemed almost imperative to solve first the problems of analysis and sampling of the metal for hydrogen. Once these problems have been solved, it would be possible to answer more of the important commercial problems mentioned above. As a consequence, it was decided to design an analytical apparatus and, upon satisfactory completion of this, to develop an accurate method of sampling liquid metal for hydrogen.

Jan 1, 1951

By F. D. Rosi, C. A. Dube, B. H. Alexander

WHEN a deformed polpcrystalline metal is heated to a sufficiently high temperature, a recrystallized structure develops which consists of small, essentially stress-free grains. This transformation is referred to as primary recrystallization. Under certain conditions, on prolonged annealing of the specimens, a type of grain coarsening occurs in which a small number of grains commence to grow at various points by devouring the neighboring finegrained primary structure, which, in itself, exhibits a marked stability toward normal grain growth. This grain coarsening process has been referred to by Burgers' as "secondary recrystallization" or "exaggerated grain growth." Although much work has been done on recrystallization and growth processes, present knowledge of the factors which determine the occurrence and growth of secondary grains is inadequate for the advancement of a theory which accounts for the observed characteristics of this recrystallization phenomenon. In this respect, it would be important to make measurements of the velocity of growth of these large secondary grains. The early work of Feitnecht2 on aluminum showed that the size of secondary grains increased with temperature and time, suggesting that such measurements would be possible. More recently, Burgers1 found that the growth velocity of these grains in aluminum was constant over a large time interval, as is generally found for the growth velocity of primary grains in a uniformly deformed test piece.3-5 It is reasonable to expect that the determination of the activation energy of the secondary growth process might lead to a better understanding of the underlying atomic mechanism. This investigation, therefore, is one of a series primarily designed to measure the growth velocity of secondary grains at various temperatures for silver, copper, and aluminum. It is hoped that these studies along with those of orientation relationships, will establish a sound basis for theorizing as to the origin and nature of the secondary transformation. Experimental Procedure The metal used in the present investigation was high-purity silver (999.9 fine), which was supplied in the form of cold-rolled plates 0.250 in. thick. These plates were annealed at 500°C for 1 hr and then straight-rolled to a thickness of 0.04 in. in three reductions of approximately 45 pct, followed in each case by an anneal at 450°C for 1/2 hr. The 0.04 in. sheets were given a final reduction of approximately 50 pct, which resulted in a thickness of 0.02 in., thereby insuring two-dimensional crystal growth. Individual specimens of this material about 1x3 cm were used for all heat treatments, unless otherwise noted. The annealing was carried out under an atmosphere of argon in an Inconel tube furnace whose temperature was controlled to within -+2°C. Metallographic examination of the secondary transformation was accomplished by mechanically polishing the specimens on one side to approximately one half their thickness through 2/0 metallographic emery paper, and then electrolytically polishing in a solution of potassium ferrocyanide and sodium cyanide. With a current density of approximately 20 amp per sq dm, the time required to obtain a satisfactory surface varied from 3 to 5 min. Standard potassium bichromate was used to etch the electrolytically polished surfaces. A heavy etch with this solution produced a sharp contrast between the secondary grains and the fine-grained primary structure, darkening the latter while leaving the large secondary grains bright. All area measurements of the secondary crystals were made with a planimeter on enlarged tracings of the grains.

Jan 1, 1953

By John S. Brown

As a part of a symposium on the relations of structure to ore deposition, in February 1938, the writer presented some tentative opinions derived from his experience with a number of important lead-zinc replacement deposits. These ideas were set forth, as a basis for discussion and a stimulus to further inquiry, in a mimeographed leaflet that read as follows: Intimate acquaintance with a number of lead and zinc deposits in metamorphosed limestones seems to indicate the existence of certain common features from which can be established some general principles governing the localization of ore in this type of formation. It is suspected that these principles can be applied, with modifications, to mineralization in unmetamorphosed limestone. In metamorphosed formations, some observed rules are as follows: 1. Bands or masses of pure limestone are very resistant to replacement by ore solutions, and are likely either to contain no ore or to resist replacement until near the end of mineralization. The reason for this apparently is physical, not chemical, since microscopic data indicate that when ore is deposited by far the greater part of it substitutes for carbonate. The chief factor is believed to be a lack of porosity in massive limestone that has undergone flowage and recrystallization. 2. Masses of intensely siliceous or silicated rock are likewise unfavorable ore receptacles. This seems to be accounted for by two factors: (a) chemical unsuit-ability or resistance to replacement, and (b) physical resistance to small-scale brecci-ation, which might faeilitate the opening of effective channelways for solutions. Some low-grade ore may occur, however, and also sporadic fracture fillings. 3. The optimum condition for ore reception appears to be found in bands or areas containing carbonate and silicates (or quartz) intimately mingled in something like equal proportions. In this situation movement is likely to result in mixed flowage and fracture, producing a finc-textured porosity that admits solutions freely and provides access to an abundance of replaceable carbonate. Cleavage cracks in some minerals such as diopside are believed to facilitate the penetration of solutions. 4. Certain minerals or assemblages are regarded as favorable impurities in a limestone and others as unfavorable. Original quartz, and subsequently developed diopside, and perhaps garnet, are typical favorable pre-ore gangue; in general rather equidimensional, brittle minerals. Tremolite, biotite, and probably wollastonite, are typical unfavorable pre-ore gangue; in general highly elongated and somewhat flexible minerals likely to develop under strong shearing stresses. 5. Tentative opinion is that the ratio of lime and magnesia in a limestone is of little or no importance.

Jan 1, 1941

By John S. Brown

As a part of a symposium on the relations of structure to ore deposition, in February 1938, the writer presented some tentative opinions derived from his experience with a number of important lead-zinc replacement deposits. These ideas were set forth, as a basis for discussion and a stimulus to further inquiry, in a mimeographed leaflet that read as follows: Intimate acquaintance with a number of lead and zinc deposits in metamorphosed limestones seems to indicate the existence of certain common features from which can be established some general principles governing the localization of ore in this type of formation. It is suspected that these principles can be applied, with modifications, to mineralization in unmetamorphosed limestone. In metamorphosed formations, some observed rules are as follows: 1. Bands or masses of pure limestone are very resistant to replacement by ore solutions, and are likely either to contain no ore or to resist replacement until near the end of mineralization. The reason for this apparently is physical, not chemical, since microscopic data indicate that when ore is deposited by far the greater part of it substitutes for carbonate. The chief factor is believed to be a lack of porosity in massive limestone that has undergone flowage and recrystallization. 2. Masses of intensely siliceous or silicated rock are likewise unfavorable ore receptacles. This seems to be accounted for by two factors: (a) chemical unsuit-ability or resistance to replacement, and (b) physical resistance to small-scale brecci-ation, which might faeilitate the opening of effective channelways for solutions. Some low-grade ore may occur, however, and also sporadic fracture fillings. 3. The optimum condition for ore reception appears to be found in bands or areas containing carbonate and silicates (or quartz) intimately mingled in something like equal proportions. In this situation movement is likely to result in mixed flowage and fracture, producing a finc-textured porosity that admits solutions freely and provides access to an abundance of replaceable carbonate. Cleavage cracks in some minerals such as diopside are believed to facilitate the penetration of solutions. 4. Certain minerals or assemblages are regarded as favorable impurities in a limestone and others as unfavorable. Original quartz, and subsequently developed diopside, and perhaps garnet, are typical favorable pre-ore gangue; in general rather equidimensional, brittle minerals. Tremolite, biotite, and probably wollastonite, are typical unfavorable pre-ore gangue; in general highly elongated and somewhat flexible minerals likely to develop under strong shearing stresses. 5. Tentative opinion is that the ratio of lime and magnesia in a limestone is of little or no importance.

Jan 1, 1941

By H. l. Burghoff, A. I. Blank

The state of knowledge bearing on the stability of copper under stress at elevated temperatures is generally known to be in need of revision and extension. The present investigation, dealing with the creep characteristics of a deoxidized copper of low residual phosphorus content, is intended to contribute in some small measure toward this end. The experimental data presented herein have been correlated by methods of evaluation and interpretation familiar to those who are concerned with crecp of metals. In practice it is common, if not requisite, to use structurally stable materials at elevated temperatures. It is frequently desirable, however, to test materials under conditions that produce structural change, in order to determine the extent of such change and its effect on physical properties, thus making it possible to establish accurately the limiting conditions to which such materials may be safely exposed. The creep characteristics of the drawn copper wire of this investigation arc directly associated with its structural instability at elevated temperatures. Complete realization of this fact is essential to the evaluation of its creep resistance under various conditions. Creep results should apply to steady deformation under equilibrium conditions, but these are seldom attained in only one or two thousand hours. It will be shown that steady creep rate for copper at useful stresses does not usually begin until considerably more time has elapsed. A wholly satisfactory substitute or shortcut for extensive creep testing does not appear to be evident in the application of mathematical analyses to limited experimental data. Material A single lot of phosphorized copper wire was drawn down to 0.125-i11. diameter with a final reduction of 84 per cent. After mechanical straightening, a portion of this wire was annealed to an average grain size of 0.013 mm. in a controlled-atmosphere furnace. The composition and initial properties of the copper in these two conditions are listed in Table I. Photomicrographs of the original structure are shown in Fig. I.

Jan 1, 1945

By Lawrence H. Van Vlack, Otta K. Riegger

Periclase-type oxides were examined microscopically after being exposed to siliceous liquids. The rate of grain growth was found to be inversely proportional to the grain diameter. Grain growth proceeds more rapidly at higher temperatures, but is retarded by increasing liquid contents. aMag-nesiowiistites with higher MgO contents grow less rapidly than those with higher FeO contents. The growth rate is reduced by the presence of a second solid phase. The silica-containing liquid penetrates as a film between the individual magnesiowus tite grains. This is independent of time, temperature, amount of liquid, or the MgO/ Fe0 ratio. When present, olivine and spinel-type phases can provide a solid-to-solid &apos;&apos;bridge" between magnesioustite grains. THIS paper presents the results of a study of the microstructures of periclase type oxides in the presence of a silicate liquid. The purpose was to learn more about the effect of service factors such as 1) time, 2) temperature, and 3) liquid content upon A) grain growth, and B) liquid location among the solid grains. This study was prompted by the fact that periclase refractories are known to have very little solid-to-solid contact when the phases which are present are limited to periclase and liquid. Such a micro-structure gains industrial significance because it permits fracture during service when stresses are applied at high temperatures. The details of ceramic microstructures have not received extensive attention. This is in contrast to the extensive attention given to a) the phase relationships pertaining to refractory compositions, and b) the details of the microstructures of comparable metallic materials. A brief review will be made of the pertinent phase relationships and microstructural considerations in general, as well as of refractory compositions. a) Phase Relationships. This investigation was limited to those compositions in which (Mg, Fe)O was the solid phase. MgO and FeO form a complete series of solid solutions. Pure MgO has the name of periclase. The related FeO structure is called wustite. Both have the NaC1-type structure: however, wustite possesses a cation deficiency so that the true composition is Fe<10 even in the presence of metallic iron. The phase relationships involving solid (Mg, Fe)O and a silicate liquid are shown in Fig. 1. In this case. the liquid is saturated with (Mg, Fe)o. There-fore its SiOz content is below that encountered in orthosilicate liquids. As a consequence the liquid phase specie:; are primarily the following ions: and 0-&apos; plus occasional Fe+ ions. Two features are of importance: a) the liquid contains relatively small species and b) the liquid contains large quantities of the same species as the solid. viz., Fig. 2 shows the system, FeO-SiOz, which will be used in some of the discussions that follow. This diagram is the right side, vertical section of Fig. 1. Here, as pre\iously, the composition at the FeO end of the diagram is nonstoichiometric, varying from Feo.950 when the liquid oxide is in contact with the solid iron, to about Fe 0, when the solid oxide is in equilibrium with an atmosphere of equal proportions of CO and C02 at the solidus temperature. The Fe/O ratio will be maintained in wustite in the presence of SiO,. However, the FeM/Fe++ ratio in the liquid will be lower because of the effect OIF the SiO, on the activity of the FeO. With the addition of MgO to wustite, the over-all composition (IvZg, Fe)@, has a value of x lying between 0.9 and 1.0 when the COz/CO ratio is 1.0&apos;. b) Microstructures. In general, published attention to refractory microstructures has been directed toward the phase analyses that accompany compositional variations. This is illustrated by Harvey6 in his work on silica brick and by wells7 in his work on periclase brick. In each case, a series of altered zones is encountered which provides a sequence of phase associations. If due consideration is given to reaction kinetics, such an examination reveals phases that are compatible with equilibrium studies. Admittedly, however, it is often necessary to determine more complicated polycomponent systems to account for all the phases present.8 Relatively little attention has been given to microstructural geometry in ceramic materials. Certainly less attention has been given to this aspect of ceramic microstructures than to the size, shape, and distribution of the constituent phases in metals. Burke has pointed out that the grain size of oxides follows the same growth rules as for metals, viz.,

Jan 1, 1962

By M. A. Selim, W. H. Somerton

Thermal expansions and heats of reaction of three typical sandstones were measured in the temperature range of 25°to 1,000°C. The significance of these data in subsurface heat-transfer calculations is discussed. Linear thermal expansions were measured both parallel and perpendicular to the bedding planes. Volume expansions are reported as the perpendicular expansion plus two times the parallel expansion. Expansion behavior of the sandstones was found to be controlled by the expansion characteristics of the quartz content. Differential expansion of the quartz grains and other minerals included in the sandstones caused permanent deformation of the heated samples after they were cooled to room temperature. Structural damage resulting from heating is probably an important cause of the reduction of thermal conductivity of heated samples. Measurements of heats of reaction were based on the known heat required for a- quartz inversion. Thermal reactions, which probably include deby-droxylation of clay minerals and decomposition of carbonate minerals contained within the samples, were found to require more than one-fourth of the amount of heat necessary to raise the temperature of the rock alone. In shales and limestones, the reaction heat could be substantially greater than that required from specific heat considerations alone. INTRODUCTION In earlier work, l-3 methods of measuring thermal properties were developed and thermal data for several sedimentary-rock types were reported. Data included thermal conductivity, specific heat and thermal diffusivity. In addition, calculations of heat transfer in subsurface formations may require data on the thermal-expansion characteristics of rock and the heats of reaction of mineral constituents. Thermal expansion of rocks is relatively small in magnitucle and, from the standpoint of change in bulk density, has only minor effects on heat-transfer cliaracteristics. Thermal-expansion behavior, however, may have significant effects on the structure of rocks. Differential expansion of different minerals and along different crystal-lographic axes may result in structural damage which could effectively reduce the thermal conductivity of the rock. Many mineral constituents of sedimentary rocks undergo phase or related changes when heated to sufficiently high temperatures. Although some of these reactions (such as the a-ß quartz inversion) are reversible and the heat absorbed is returned to the system upon cooling, many of the major reactions are irreversible. Through certain temperature ranges, the additional heat energy required to complete the reactions may be nearly as great as that necessary to raise the temperature of the rock in the absence of thermal reactions. If the heat requirements for these reactions are not considered, serious errors in heat-transfer calculations may result. Thermal-tzxpansion and thermal-reaction data have been obtained for three typical sandstones. Methods of measurement and results obtained are reported and discussed in the following. THERMAL EXPANSION OF SANDSTONES The linear expansions of three outcrop sandstones (Bandera, Berea and Boise) have been measured in the temptbratue range of 25° to 1,000° C. Expansion measurements were made in the directions parallel and perpendicular to the bedding. The differential expansion apparatus used is that described by Mitoff and Pask.4 The test sample is heated in an electric furnace with a temperature rise of 6°C/minute. The lengthening of the samples upon heating is compared with the small and known expansion of a fused silica rod. The change in length is transmitted to an X-Y recorder by means of a Statham transducer. A maximum error of ± 1.5 per cent has been obtained with this apparatus

By Ralph V. Higgins

This paper concerns the magnitude of the amount of supersaturation that occurs in an underground reservoir during the flow of oil and gas to wells and to the amount of undersaturation that occurs during repres-suring of an oil reservoir where some effective permeability to gas exists. The study is based on earlier laboratory findings of other investigators on the rate of diffusion of gas in oil as a function of the depth of oil. Utilizing these relationships and the principles of reservoir mechanics, a quantitative estimate of undersaturation and super-saturation was calculated. The results showed that the diffusion of the gas is rapid enough that for all practical purposes no supersaturation exists during the flow of oil to wells or undersaturation during repressuring in reservoir sands having some effective permeability to gas. The reason diffusion of the gas virtually keeps the oil saturated is the long time required in radial flow for oil to reach the well and the slow rate at which pressure in reservoirs is increased during repressuring. INTRODUCTION Knowledge of the phase relationships during flow of gas and oil in an underground reservoir is essential to operating the reservoir in the most efficient manner. In material-balance calculations and in fluid-flow studies, the oil is assumed to contain all the gas that it will dissolve at given temperature and pressure. Pressure-volume-temperature relationships are normally obtained in the laboratory using "bottom-hole" or combined samples of the reservoir fluids. In such laboratory determinations equilibrium is obtained between the oil and gas in the pressure cells by mechanical agitation. During the flow of oil and gas in reservoirs, however, no comparable agitation occurs to mix thoroughly these fluids to aid in effecting equilibrium between the two phases. During repressuring of a partly depleted underground reservoir, the gas is usually injected into the reservoir faster than the oil can absorb it; consequently, the oil is undersaturated. On the other hand, as the oil flows through the reservoir to the wells during producing operations the pressure decreases faster than the gas in solution can diffuse through the oil to the gas phase. The oil therefore is supersaturated with gas. Where the oil is undersaturated, gas diffuses away from the gas-oil interface, and where it is supersaturated the gas diffuses toward the interface. In either case the gas moves from a higher to a lower saturation. This report contains the results of a study of the factors influencing the degree of nonequilibrium of the phase relations of oil and gas in porous mediums during the flow of oil through reservoirs to wells and also during the injection of gas into partially depleted sands. Data from an underground reservoir are presented and the degree of supersaturation during the flow of the oil through the reservoir to the well is approximated. Also data from another reservoir are used and the degree of undersaturation during the repressuring operation is calculated. In addition, the flow rates of oil in laboratory experiments and in underground reservoirs are compared, as data from the laboratory are often used to interpret events in the reservoir, and the rates of flow influence appreciably the degree of nonequilibrium. Much of the contents of this report was prepared in 1943; but, because of other activities during and since the war, the manuscript was left untouched until 1952, when it was decided to include an estimate of the amount of undersaturation during repressuring as well as supersaturation during flow.

Jan 1, 1955

By A. T. Tye

Regarding the results of preferential flotation at Cananea, Weinig has stated that "The concentrating mill of the Cananea Consolidated Copper Company at Cananea, Mexico, furnishes an excellent example of modern flotation practice. The complete figures are given because they present so forcibly the advantages of modern selective flotation."l L. 0. Howard notes that "Perhaps the outstanding example so far published of improverrients in results through the use of selective flotation is that at Cananea, Mexico."" The following notes indicate the conditions under which the results were obtained at Cananea; also the effect of preferential flotation at the concentrator and at the smelter. In the majority of cases the full benefit of selective flotation is not fully realized, as the concentrates are shipped from the mill to smelters owned by other companies. The saving made at a certain concentrator by this method of flotation may be well understood but the saving resulting at the smelter from the results of preferential flotation at the mill is not so apparent, as the data are contained in the smelting records of some other company. Even at the smelter the great gains following preferential flotation may not be noted, as a variety of ores and concentrates from various sources are received and the difference from the changed concentrator operations of a certain mill may be obscured. As noted by Professor Weinig and Professor Howard, the results obtained at Cananea brought about a veritable metallurgical revolution at the smelter. There are probably plants at which a better preferential separation is being made than at Cananea. Many ores contain barren iron pyrite which, when depressed, does not carry copper into the tailing. Some concentrators use clean uncontaminated water for milling and in others the ore is ground much finer than at Cananea. All of these items are concerned in perfect separation. The details of preferential flotation at Cananea, therefore, are not presented on account of the perfection of the

Jan 1, 1928

By P. Linehan, J. F. Wiss

Vibration and air blast noise from blasting were evaluated during a research program sponsored by the US Bureau of Mines. Blast variables were studied wing small scale model (SCM) tests to evaluate specific variables as well as interactive effects, followed by experiments with production blasts at the surface coal mines. Experimental data showed that the primary variables affecting the ground vibration amplitude are the charge weight per delay and the length of delay interval. Blast variables having a significant effect on the overpressure amplitude include the charge weight per delay, the length of delay, burden and spacing, stemming amount and type, direction of initiation, charge depth, and amount of detonating cord and cover.

Jan 1, 1983

By C. F. Riisness, E. R. Parker

THAT grain size has a great effect on the mechanical properties of metals has been recognized for a long time. Bassett and Davis1 in 1919 did excellent work in [ ] determining the effect of grain size on the hardness of brass. About the same time Jeffries2 and Sykes3 ascertained the effect of grain size on the strength and ductility of several metals at temperatures ranging from 80°K. to their melting points. When creep was recognized as an important property of metals, those engaged in the study of this property tried to determine the effect of grain size 4-9 on creep rates. Unfortunately, most of the investigations were conducted on only two grain sizes, often designated simply as "fine" and "coarse." It is well known that at high temperatures coarse-grained test bars creep less than fine-grained bars. The relation between grain size and size of test bar, [ ] however, has been frequently overlooked. In his early work, Jeffries2 showed that the number of grains in the cross section has a more important influence on the properties of the material than the actual grain size. More recently Hanson and Sandford10 and Pell-Walpole,11 in their measurements of the creep and tensile properties of tin, tested a wide range of grain sizes and correlated the grain size with the strength. Hanson9 later established the relation between the number of grains in the cross section and the. creep rate: At high temperatures, generally a coarse-grained structure is considered superior in creep to a fine-grained structure, but it is evident that for a given bar size continuously increasing the grain size will

Jan 1, 1944

By John Fulton

Johnstown is the site of the extensive iron, steel, and wire-works of the Cambria Iron Company. It is situated at the western base of the Alleghany Mountain, 275 miles from Philadelphia, and 78 miles from Pittsburgh. The valley in which the town and its ironworks are located, has an average elevation of 1160 feet above tide water. Johnstown, in its main features, is a modified duplicate of Pittsburgh. It is located at the confluence of the Little Conemaugh and Stony Creek rivers, which, by their union, form the Conemaugh River, just as Pittsburgh is situated at the junction of the Allegheny and Monongahela rivers, which together make the Ohio River. The site of Johnstown is in a cutting through the lower productive coal measures, 500 c feet deep, with steep slopes along the valleylimits, exposing, in sharp-cut terraces, the outcrops of the coal and iron-ore beds; the whole surmounted by the shales and sandstones of the barren measures.

Jan 1, 1885

By P. R. Bradley

The property of the Alaska Juneau Gold Mining Co., covering the Juneau gold belt for over a mile in length, consists of 136 claims and 24 mill sites; these are near Juneau, Alaska, in what is known as the Harris mining district. Gold was discovered in the district in 1880, by Richard T. Harris and Joseph Juneau, who had been prompted to explore the section by rumors they had heard among the Indians. Gold was first found on the beach at the mouth of Gold Creek and further search revealed the lode deposits in the Silver Bow basin, about two miles inland. The lode locations made immediately thereafter constitute the principal area of the Alaska Juneau group of claims. Gradually news of the strike spread and, during the late eighties, Silver Bow basin became a substantial producer of gold, both from placer work and from quartz milling. Numerous small mills of various types were erected to crush high-grade float and stringers gouged to shallow depths. Placer mining gradually ceased and the pioneer milling operations gave way to larger and better mills, which in time were the predecessors of the two large mills built by the Alaska Gastineau Co. and the Alaska Juneau Co. on the shores of Gastineau Channel. This evolution from arrastres to small mechanical mills, thence to the two large-capacity mills on Gastineau Channel, although a natural sequence of events, had a most important bearing on the development of the district. Knowledge of the character, extent, and value of the ore deposits gained by these early operations could not have been acquired otherwise. Spencer shows1 that the early mills were: Arrastres in 1881-82-83-84-85-86-88; a 5-stamp mill in 1882; a "newly devised grinding mill" in 1884; two Huntington mills in 1886; a 10-stamp mill in 1889; a revolving Dodge mill in 1890; a 5-stamp mill in 1891; and a 20-stamp mill in 1893. He also estimates the gold production to the end of 1893 as $1,000,000 from lode mining and $1,250,000 from placer mining. No estimate can

Jan 1, 1925

By N. J. Grant, D. S. Bloom

An investigation of the Cr-Mo-Ni ternary system and attendant binaries has been completed. Some changes in the binary diagrams are shown to be necessary. The 1250°C section of the ternary and the liquidus surface have been delineated. A system of invariant reactions existing above 1250°C has been suggested. BECAUSE chromium, molybdenum, and nickel are important not only as bases for alloying systems but also as major alloying additions for other refractory metals, a study of the phase diagrams is of great interest and importance. In addition there are interesting features of theoretical value, a number of which are of prime consideration in this work. The major aim was to determine the ternary phase diagram of these metals at and above 1250°C, with sufficient attention given to lower temperatures to permit an understanding of the conditions existing at 1250°C and above. To understand ternary systems it is essential that accurate information concerning the binary systems be available, which in turn presupposes thorough knowledge of the constituent elements. On the basis of this investigation not only were significant inaccuracies indicated in the binary systems but much consideration had to be given to one of the elements, that is, chromium. The observation has been made that chromium undergoes a crystal transformation at a temperature near its melting point. Much of the experimental data leading to the detection of this transformation and the effects of this hypothesis on the form of the Cr-Ni phase diagram have already been reported&apos; . and will not be repeated here. The experimental methods employed in the investigation have also been covered.&apos;-" he purity of the molybdenum utilized in this work showed by qualitative spectrographic analysis that chromium, copper, iron, silicon, and tungsten were present in quantities of 0.1 to 0.001 wt pct. During the course of the investigation more than 100 melts were made, weighing from 150 to 200 grams each. Each of these melts was sectioned for chemical analysis and for specimens for examination in the as-cast and various heat-treated conditions by X-ray and metallographic means. All X-ray diffraction patterns reproduced here were made using chromium Ka radiation although iron and copper targets were used on occasions during the investigation. Experimental Results Mo-Ni-System: The most recent comprehensive investigation of the Mo-Ni system was made by Ellinger&apos; in 1942; the diagram as shown in the American Society for Metals Handbook is based on his work. The work done on the system in this investigation substantiated the general form of the diagram although some differences were observed. These are indicated by a comparison of Ellinger&apos;s diagram and Fig. 1, the latter showing the results of pertinent thermal analyses made in this research. It can be seen in Fig. 1 that the eutectic composition is

Jan 1, 1955

By A. M. Guadin

Direct quantitative comparison of the results of concentrating operations on different ores is frequently desired but almost impossible to obtain if comparison has to be made by means of two quantities for each ore, as must be done at present. This paper represents the outgrowth of attempts to arrive at a single-number quantitative measure of the segregation between minerals or metals as the result of concentrating operations. The usual practice in estimating the effectiveness of concentrating operations, particularly those of ore dressing, has been to determine the recovery of the metal or mineral of interest and the grade of the concentrate. The difficulty in quantifying the effectiveness of concentration by the usual criteria may be illustrated by a few examples. Consider, for instance, two lead ores which yield by flotation the same recovery of lead, say 92 per cent., and the same grade of concentrate, say 60 per cent. Pb. If a substantial difference in the grade of the feed had existed, say if one ore contained 5 per cent. Pb and the other 10 per cent., it is clear that the concentrating operation was more effective in the case of the lower grade ore. It is difficult, however, in the light of these data to state how much more effective was the concentration of the lower grade ore. Consider again two lead ores containing 5 and 10 per cent. Pb and yielding concentrates containing 60 and 72 per cent. Pb respectively, with recoveries of 93 and 92 per cent. respectively; it is well-nigh impossiblc to tell from these figures which results represent the best separation of the minerals. It may be noted that in the usual method of estimating the effectiveness of the segregation of mineral values, no consideration is given to the rejection of the unwanted substances from the concentrate, except in the very indirect manner in which it enters into the grade of the concentrate. Consideration of the rejection of gangue from the concentrate, adequately weighted with recovery of the desired mineral in the concentrate, should supply an adequate criterion of concentration effectiveness.

Jan 1, 1930

By Edward F. Fitzhugh

Quantitative appraisal of the chances of finding various tonnages and grades of ore clarifies any exploratory development proposal. Ways are discussed of appraising chances in conformance with probability principles, and graphs are suggested to show tonnages, grades and the corresponding judged expectancies. Introduction When exploratory development of a mineral deposit is contemplated, three interrelated questions normally must be answered before a sound decision can be reached. How much will the program cost? How much will the anticipated ore add to the immediate value of the mine? And what is the chance of developing this ore? To justify development, the deposit should present a favorable disparity between the three factors, cost, chance and return. If, for example, there is a 50-50 chance of success, the ore that is sought should have an immediate worth (after deducting all subsequent charges that it must bear) of more than twice the cost of the development. Likewise, if the chance of finding the ore is but one in five, that ore should enhance the immediate value of the mine by more than five times the cost of developing it- With sound economic and operating assumptions, the cost of exploratory development and a present value of anticipated ore may be estimated within reasonable limits. Less general attention has been given to appraising ore chances in comparable terms. The exploratory experience of the mining industry is broad enough that knowledge, vision and judgment may be combined to yield more tangible evaluations of Ore expectancy than are now customary&apos; A way of making such appraisals is suggested herein. The mathematics of probabilities cannot be applied directly to the search for ore. By coupling applicable principles of probability, however, with pertinent experience gained in mineral exploration, an estimate often can be made of the chance of finding a certain tonnage and grade of Ore in a specific location. Such estimated, or judged, expectancies for the several blocks of ground in a deposit may be combined in a simple chart to show the relationship of the various exploratory possibilities and the potential magnitude of the deposit&apos; An engineer or geologist may find that the quantitative thinking required for an appraisal of this type is an aid in clarifying and coordinating his views and recommendations. For a person wishing to understand these views, an ore-expectancy

Jan 1, 1949

By Edward F. Fitzhugh

Quantitative appraisal of the chances of finding various tonnages and grades of ore clarifies any exploratory development proposal. Ways are discussed of appraising chances in conformance with probability principles, and graphs are suggested to show tonnages, grades and the corresponding judged expectancies. Introduction When exploratory development of a mineral deposit is contemplated, three interrelated questions normally must be answered before a sound decision can be reached. How much will the program cost? How much will the anticipated ore add to the immediate value of the mine? And what is the chance of developing this ore? To justify development, the deposit should present a favorable disparity between the three factors, cost, chance and return. If, for example, there is a 50-50 chance of success, the ore that is sought should have an immediate worth (after deducting all subsequent charges that it must bear) of more than twice the cost of the development. Likewise, if the chance of finding the ore is but one in five, that ore should enhance the immediate value of the mine by more than five times the cost of developing it- With sound economic and operating assumptions, the cost of exploratory development and a present value of anticipated ore may be estimated within reasonable limits. Less general attention has been given to appraising ore chances in comparable terms. The exploratory experience of the mining industry is broad enough that knowledge, vision and judgment may be combined to yield more tangible evaluations of Ore expectancy than are now customary&apos; A way of making such appraisals is suggested herein. The mathematics of probabilities cannot be applied directly to the search for ore. By coupling applicable principles of probability, however, with pertinent experience gained in mineral exploration, an estimate often can be made of the chance of finding a certain tonnage and grade of Ore in a specific location. Such estimated, or judged, expectancies for the several blocks of ground in a deposit may be combined in a simple chart to show the relationship of the various exploratory possibilities and the potential magnitude of the deposit&apos; An engineer or geologist may find that the quantitative thinking required for an appraisal of this type is an aid in clarifying and coordinating his views and recommendations. For a person wishing to understand these views, an ore-expectancy

Jan 1, 1949