Search Documents

By A. E. Blakeslee

Morphological and electrical properties of GaAs epitaxial layers are influenced not only by changes in the nominal substrate orientation but also by small amounts of misorientation from the exact crystal planes. Deviations up to 5 deg from {11IA}, {11IB}, and (100) planes were investigated. Growth rates increase progressively with angle, approximately I u per hr per deg. Size and density of growth pyramids fall off with increasing angle, but other effects that are deleterious to the surface may occur which are heightened by increased misorientation. Carrier concentration decreases and electron mobility consequently increases as the angular offset increases, except in the case of strong compensation, where the mobility trend is reversed. It has long been known that changes in the crystallo-graphic orientation of the substrate may cause pronounced effects on the morphological properties of vapor grown semiconductor films. Reports of orienta-tion-dependent growth rates and surface characteristics are as old as the literature on epitaxy itself. shawl has recently published a comprehensive study of the dependence of growth rate on substrate temperature and orientation in epitaxial GaAs. It is also well-known that misorienting the substrate surface a few degrees away from the nominal low-index crystal-lographic plane often produces a much smoother epitaxial surface. This was reported by Tung2 for silicon, Reisman and Berkenblit3 for germanium, and by Kontrimas and Blakeslee4 for GaAs, and use is commonly made of this fact in the semiconductor industry to help guarantee smooth vapor deposits. The effects of substrate orientation on the carrier concentration and mobility of vapor grown GaAs were first documented by williams5 in 1964 and have been observed by several other authors since then,6,7 but no one has yet reported a careful study of how small changes influence these properties. We have made such a study and have found that sizable differences in growth rate, morphology, carrier concentration, and mobility can indeed be observed for epitaxial films grown on substrates that are oriented by progressive small increments away from the exact crystal plane. EXPERIMENTAL Early in the investigation an arsine synthesis system of conventional design8 was employed to produce growths on {111A}-oriented GaAs substrate crystals. In that early work, pronounced effects on carrier concentration and electron mobility were observed as a function of slight misorientation from this low index plane. That observation led to the more careful study that is reported here. An AsC13 system, differing in major aspect from those commonly in use today9 only in that the reactor is vertical rather than horizontal, was used for the detailed study. The gallium source was at 900°C and the substrates were at 750°C. The flow rate of pal-ladium-diffused H2 through the AsCl3 bubbler was 200 cu cm per min, and the flow rate of bypass H2 was also 200 cu cm per min. The substrates consisted of chro-mium-doped semiinsulating GaAs to facilitate elec-trical evaluation of the overgrowth by means of Hall and conductivity measurements on conventional eight-legged Hall bridges. They were misoriented by 0 to 5 deg from the {111A}, {111B}, and (100) planes, toward the (100) from the {111A} and {111B} and randomly toward the <111A> or <111B> from the {loo). The crystals were oriented for sawing by the Laue back-re-flection technique, which is good only to about ±1/2 deg; but after polishing or sometimes after epitaxial growth the wafers were checked by a diffractometer technique which is accurate to about * 0.1 deg. After lapping, the wafers were polished with NaOCl after the technique of Reisman and Rohr,10 and just before use they were cleaned in NaOC1, thoroughly rinsed with de-ionized water, and blown dry with nitrogen. Each run employed four wafers, each misoriented by differing amounts from one of the three major faces, and at least two runs were made for each orientation. The runs were continued long enough to provide at least a 15-µ or thicker layer. SURFACE MORPHOLOGY The appearance of all the films that were grown in a given run always changed from wafer to wafer as a function of increasing misorientation, but not always in the same regular fashion. At least three different trends were observed. These are more easily seen than described, and reference to the series of photo-

Jan 1, 1970

By Jack Green

Within three major tectonic time frames of earth history: Microplate (±3.8 - ±2.6 billion years), intraplate (±2.6 - ±1.3 b.y.), and macroplate (=1.3 b.y. - present), precious - metal deposits are confined to specific structural, depositional and physico-chemical environments. Precambrian primary gold deposits are localized in two microplate greenstone episodes (±3.7 and ±2.7 b.y.); secondary gold in Witwatersrand placers (±2.6 b.y.). Precambrian primary platinum group metals are in anorthositic facies of layered mafic intrusions (±2.8, ±1.8 and ±1.0 b.y.). Most radioisotope mineral dates cluster - at these times and are coincident with inflections on polar wandering curves. These coincidences may reflect episodicity in lunar tidal disruptions and global deceleration effects in crust and outer core during micro- and intra- plate phases. Macroplate tectonics and an oxygenated atmosphere created favorable conditions for strata-hosted and plate suture gold and silver deposits. "Black smokers" at constructive plate margins and calc-alkalic calderas at destructive plate margins are loci for hydrothermal gold and silver.

Jan 1, 1984

By Carle R. Hayward

ATHOUGH there are signs of improvement in the lead industry, conditions are still far from what we have been accustomed to call normal. There has been little to stim¬ulate research and those responsible for the finances of the companies have been inclined to discourage expenditures except where need was urgent or the prospect for immediate returns bright. In spite of this fact, improvements have been developed here and there which will be available as business conditions become adjusted. No publicity is allowed at present. The rising price of silver has had a tendency to increase the production of lead from argentiferous ores but the greatest interest continues to be in the secondary field. Practically all lead plants situated near large centers of population are treating scrap materials, particularly battery plates, the quantity of which is increasing with the improvement in automobile sales.

Jan 1, 1936

By Gordon M. Yocom

A PROPER consideration of the subject of this paper should include economic aspects as well as the technical phases of the metallurgy, production, and properties of the product. The metallurgical phases of the processing and properties of the product will be considered only from practical aspects and within the scope of the writer&apos;s experience with tonnage production. The Bessemer process was invented 85 years ago and became important because it put steel manufacture upon a larger and less costly basis. In America the Bessemer production has declined for many years and has not maintained its proportionate place with the rapid advances of the open hearth. The achievements in the open-hearth field were attained by the greater number of technical people attracted to that branch of the industry. The antipathy of technical students for the older and less popular Bessemer field gradually weakened the forces defending it and retarded the development of new and better methods. In Europe the economic advantage of the basic Bessemer process has not been overlooked and the tonnage usually is greater than that of the open hearth. The acid process has been the subject of renewed attention in America during the past few years and those who are more familiar with it are striving to show that the method is too valuable to abandon. A considerable tonnage of Bessemer-blown metal, in both molten and ingot forms, used in connection with the open-hearth practice makes it an important auxiliary unit to the industry. This practice aids in modifying the price level of heavy remelting scrap in addition to speeding up the open-hearth operation. The use of Bessemer steel has continued not only because of periodic economic advantages but also because of certain inherent qualities of machinability, weldability and stiffness, which are valuable for many applications. The properties of stiffness and rather high reaction to cold-work require some modification in order to meet the demands of modern methods of processing, which involve cold-reduction and cold-forming. At least one factor contributing to the stiffness of this steel is the relatively high phosphorus content of the acid product. The phosphorus content of the Thomas or basic Bessemer steel of Europe is considerably lower than the normal acid product in America. The American industry has continued the use of the acid process chiefly for the reason that the available ores are more easily adapted to this process from both metallurgical and economic standpoints. In European practice the basic process is necessary with the highly phosphoric ores available and it is sustained to some degree by the sale of the rich phosphate slag as a by-product. The basic process was used in this country at several plants many years ago, but was abandoned for economic reasons. A part of the past history of these trials is given here because the author believes it has not been published and it has some bearing on the subject of this paper. The information is authentic to the extent that

Jan 1, 1941

By D. J. McAdam, G. W. Geil, D. H. Woodard, W. D. Jenkins

.In a series of papers, the authors and their associates have shown that the resistance of a metal to fracture is a function of all three principal stresses. Consequently since a technical cohesion limit is defined as the technically deter-minable resistance to fracture under a specific stress system, the technical cohesive strength comprises an infinite number of technical cohesion limits corresponding to the infinite number of possible combinations of the principal stresses. As shown in the previous papers, the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,$ namely, the stress system, plastic deformation, temperature, and the strain rate. The effect of each of these factors on the fracture stress is qualitatively the same as its effect on the flow stress. The effect of any of the factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. Since the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. In the general investigation described in the previously-mentioned papers, 10-18,20,21,23 the influence of the stress system on the fracture stress was studied by means of tension tests of notched specimens. When a circumferentially notched cylindrical specimen is subjected to longitudinal tension, the minimum cross section is under transverse radial tension. The mean radial stress increases with the depth and sharpness of the notch, but is always less than the longitudinal stress. The greatest principal stress (S1), therefore, is longitudinal, and since the radial stress is effectively equal to the circumferential stress, the transverse principal stresses are equiaxial in that plane (Sz = S3). By the use of notched specimens in tension tests it was shown that the fracture stress increases with increase in the radial stress ratio (s3/s1) The evidence is based not only on the results of tests to fracture at various constant temperatures, but also On results of two-stage tests, in which each specimen was plastically deformed a predetermined

Jan 1, 1949

By D. J. McAdam, G. W. Geil, D. H. Woodard, W. D. Jenkins

INTRODUCTION IN a series of papers, the authors and their associates have shown that the resistance of a metal to fracture is a function of all three principal stresses. 10-18,20,21,23,[1] Consequently since a technical cohesion limit is defined as the technically determinable resistance to fracture, under a specific stress system, the technical cohesive strength comprises an infinite number of technical cohesion limits corresponding to the infinite number of possible combinations of the principal stresses. As shown in the previous papers, the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,§ namely, the stress system, plastic deformation, temperature, and the strain rate. The effect of each of these factors on the fracture stress is qualitatively the same as its effect on the flow stress. The effect of any of the factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. Since the term "fracture stress" has come into general use with the same significance as technical cohesion limit; the authors are here using the&apos; shorter term with the understanding that it, does not always refer to actual fracture. In the general investigation described. in the previously-mentioned papers,10-18,20,21,23 the influence of the stress &apos;system on the fracture stress was studied by means, of tension tests of notched specimens. When a circumferentially notched cylindrical&apos; specimen is subjected to longitudinal ten-, sion, the minimum cross section is under " transverse radial tension. The mean radial stress increases with the depth and sharpness of the notch, but is always less than the longitudinal stress. The greatest principal stress (S,), therefore, is longitudinal, and since the radial stress is effectively equal to the circumferential stress, the transverse principal stresses are equiaxial in that plane (S2 = S3). By the use of notched specimens in tension tests it was shown that the fracture stress increases with increase in the radial stress ratio (S3/SI). The evidence is based not only on the results of tests to fracture at various constant temperatures, but also on. results of two-stage tests, in which each specimen was plastically deformed a predetermined

Jan 1, 1948

By Walter Renton Ingalls

Metallurgical literature has no record of any ore beneficiated for cadmium alone, and the cadmium of commerce is derived from zinc ore, with which cadmium is generally associated. Zinc ores free from cadmium—e.g., the ores of the Franklin and Stirling mines, New Jersey, and of Broken Hill in Rhodesia—are rare. Blende concentrates of 50 to 60 per cent grade have contained (in production of important tonnage) as much as I per cent Cd, which is unusually high. The concentrates from the Tri-State district average from 0.3 to 0.4 per cent Cd, which is high. The concentrates from mines west of the Rocky Mountains seldom are higher than 0.2 per cent. In the periodic system of the elements, cadmium is in the same group with zinc. Its properties and compounds are similar. Its metallurgy is also similar. Cadmium has a melting point of 320°C. and a boiling point of 778"C., while the melting point of zinc is 415&apos;C. and the boiling point gos°C. These conditions, together with the lower reduction temperature of cadmium oxide, indicate means for. separating cadmium from zinc. Cadmium in spelter is viewed, if not as an impurity, at least as an alloying element that may be objectionable, its special effect being hardening. However, for some purposes, a little cadmium in spelter is desired, and 0.4 per cent may be permissible, even in spelter for rolling. Cadmium in spelter for brassmaking is completely volatilized at the temperature of that process, and in bygone days an immense quantity of cadmium must have been lost in the fumes from these furnaces. Pyrometalltjrgy—Early Cadmium compounds, sulphide and oxide, being more volatile than the corresponding compounds of zinc, loss of cadmium begins to occur from the first furnace operation. In normal roasting, even with Tri-State ore, this loss may not be very high. Raw ore, assaying 0.4 per cent Cd, may be expected to give a roasted product of the same assay, which would imply a cadmium loss of about 15 per cent. Roasted ore, assaying 0.4 per cent Cd when distilled at ordinary furnace temperature, yielded spelter containing about half of that in the ore charged. The first draw of spelter under these conditions may assay 0.8 per cent Cd (accounting for 22 per cent of the cadmium recovery) and after the several draws of spelter have been equalized the cadmium content may average 0.35 per cent. If, therefore, 2000 lb. of blende averaging 0.35 to 0.4 per cent Cd is roasted and distilled, there may be obtained 1000 lb. of spelter, assaying 0.35 per cent Cd or 3.5 lb. content, which entering into Prime Western spelter will be sold at the spelter price. It will be observed from the outline hereinbefore (summarizing conditions prior to the introduction of sintering) that the main loss of cadmium occurred in the distillation process and by failure to condense, which could be ameliorated by attaching a prolong to the condenser, thus collecting

Jan 1, 1944

By Jerry G. Rose, Robert C. Howell

This paper addresses a process by which both the disposal and utilization of preparation plant coal refuse can be simultaneously accomplished with an attendant benefit of significantly increasing the percentage of extractable coal. A laboratory study is described in which coal refuse was successfully utilized as an aggregate in low cost concrete (coal-crete) mixes under simulated mine environments. Coal-crete specimens with compressive strengths of 14 000 kPa (2000 psi) were consistently produced. A construction sequence and mining plans are offered for placing the low-cost coal-crete pillars in accessible areas in room and-pillar mines so that a substantial portion of the remaining coal pillars could be extracted. The method could be applicable in areas where mining procedures do not permit pillar extraction became of possible surface subsidence, roof problems, or other conditions. Possible structural difficulties with the coal- crete pillar support system are discussed. Using a discounted cash flow analysis, the economic feasibility of mining with the coal-crete pillar system is investigated. The cost of the system is compared to the cost of a mining system which would have less coal recovery. The analysis indicates that although at higher coal selling prices the coal-crete mining system may yield an acceptable rate of return, the alternative of leaving the coal pillars is more attractive at the present time.

Jan 3, 1979

By Ross Glanville

INTRODUCTION The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR can also be expressed as the Optimum Mine Life (OML) in years since the expected mine life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mine life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mine life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low-tonnage mines (such as many underground gold/silver deposits) often lead to sub-optimal results. In fact, an apparently uneconomic deposit at an arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mine properties based on arbitrary production rates. This paper analyzes the interrelationships of variables such as production rates, capital and operating costs, cut-off grades, discount rates, metal prices, etc. The analysis shows that the OML for high-grade/low-tonnage deposits is often in the range of two to four years. Although such mine lives intuitively appear too short to many individuals, it should be noted that, in the past, much of the mining industry became familiar with the economics of large scale mining operations. The rules of thumb developed for such large scale operations should not be applied to high-grade/low-tonnage mines such as many of the underground gold deposits. DEFINITION OF OPTIMUM PRODUCTION RATE The OPR is selected on the basis of maximizing the net present value of the after-tax cash flows. However, as discussed later in this paper, the production rate selected for a particular mine may be somewhat higher or lower than the theoretical OPR as a result of other variables such as: 1) the probability or expectation of additional reserves being discovered 2) the likelihood of being able to custom mill nearby deposits owned by others 3) the configuration or attitude of the orebody, which may place upper limits on the production rate 4) the residual, or salvage values, of the mine/mill facilities COMPARISON BETWEEN DIFFERENT PRODUCTION RATES For an orebody with definite physical cutoffs*, or boundaries (such as faults or unconformities), the total ore reserves at different production rates may be identical. Consequently, for such an orebody, varying production rates result in differing mine lives. Although the metallurgical recoveries, the mine dilution, and other similar physical parameters may vary slightly at different production rates, the major differences are the capital costs and operating costs per ton. The ramifications of these differences are especially important at low production rates (up to approximately 1000 tons per day), but can also be significant at higher production rates.

Jan 1, 1985

By F. T. Havard

(Canal Zone meeting, November, 1910.) I. INTRODUCTION. THE present truce in litigation between Western smelting and ranching interests gives opportunity for a summary of the results achieved by metallurgists in condensing fume and de-acidifying furnace-gases. In the absence of complete records of past experiments, there has been a good deal of unnecessary duplication of attempts and&apos; failures. Yet, especially under the recent policy of our large corporations, looking to the economic recovery of the values of by- and waste products, original and, in some cases, effective measures have been developed by American metallurgists. In the case of Bliss vs. the Anaconda Copper Mining Co., the Montana Supreme Court, recognizing the progressive efforts made to render the flue-gases innocuous, and the value to the community of the smelting company&apos;s operations, refused to hamper its work, and returned a verdict in favor of the defendant. In the trial, the experimental firms of the company in the so-called "affected region" were proved to be thriving perfectly, showing that immunity was guaranteed to vegetation and stock by the wide distribution of the sulphurous acid gas in the dry air of Montana. Indeed, L. S. Austin has proved that by the time the fume is 4,000 ft.. distant from the stack, the percentage of sulphurous acid has been diminished from 2.28 to 0.00045; and Angus Smith has shown that rain must contain 40 parts per million of free acid before vegetation is affected. The arsenic in the stack-gases is but a very small part of the original content of the ore, of which 80 per cent. and over is rejected in the concentrator and furnace waste-products or recovered in the flues. Nevertheless, neither the peace in Montana nor the armistice

Aug 1, 1910

By D. W. Brunton

THE maps of our large mines are usually prepared with the greatest care; and it is somewhat singular that, in comparison with the great amount of time and money spent in surveying and platting, so little actual use is made of them. Almost the only purpose for which a completed survey-map is afterwards consulted, is the determination of the relative position of the different workings to each other, and to the boundary-lines of the property. After the completion of such a map, it should be made the beginning of another, and in most cases a far more important, undertaking, namely, its utilization as -a starting-point for a complete inventory of the company&apos;s underground possessions. The ordinary mine-survey map, being nothing but a record of what has been done, is, in one sense, only ancient history. To increase its value, such additions should be made as will render it a complete statement of the amount and value of ore in sight at any particular time, and a guide for future develop¬ments. Comparatively little extra labor is involved in this undertaking, since the larger and most expensive part of the work has already been completed when the mine has been surveyed and mapped. The necessary additions consist in working out, and platting on the maps, the geology of the mine as exposed in the workings, in such a manner that the geological survey may be of daily use in the development and operation of the mine. The first step towards the production of a geological map consists in tracing individual level-sheets from the general or composite map. The area to be included, outside of the property in question, will depend very much on local conditions; but, for geological, legal and commercial reasons, it should be extended as far as reasonably practicable. The scale to be

Sep 1, 1905

The Iron and Steel Committee of the American Institute, of mining and Metallurgical Engineers held a joint session with the American Foundrymen&apos;s Association during the Annual Meeting of the Institute in February, 1928, for the purpose of discussing blast-furnace operations and the character of pig iron and castings. Dr. Richard Moldenke presided. H.. H. Sweetser, who was named on the program as the presiding officer of the session, was unable to be present, but sent a letter in which he said: " The meeting we had here last year and the meeting held in Chicago last June showed a desire on the part of blast-furnace men and users of pig iron to get the facts regarding the influence on castings made from pig iron produced in blast furnaces under varying conditions of temperature, mixture and local furnace operations. It has been my hope that at this Round Table we might he able to formulate a series of tests that, would give us the desired information. "Several independent blast-furnace investigations have. been, and still are being, carried on in different sections of the country. The furnaces investigated include a southern furnace, a middle-west furnace, a western furnace and a Chicago district furnace. The results so far show distinct characteristics for each of the four furnaces. It is possible that a furnace in the eastern part of the United States would be different from all the others. "It is hoped that a plan of action can be worked out at your meeting today whereby the IT. S. Bureau of Mines will be able, to carry on more extensive work in connection with the research departments of the different iron and steel companies and the big consumers of pig iron. "No one group can get all of the, information but if the different investigations can be coordinated it will he possible for us to (Iran. conclusions regarding the effects of varying conditions in blast-furnace practice on the pig iron produced and the castings made there from." DISCUSSION R. Moldenke, Watehung, N. J.—I was across the -water this summer and saw some of those interested in an investigation of this kind. &apos;I&apos;hey told me that in Germany, where they had a joint committee of blast-furnace operators and foundry-

By William P. Shinn

Jan 1, 1881

By P. L. Russell

The use of nuclear explosives for excavation has been demonstrated to be feasible and practical. Application of nuclear explosives for overburden removal from large ore deposits appears to offer economic advantages over present methods, but under the present pricing schedule, high-yield devices must be used to obtain an economic advantage. The use of nuclear explosives presents problems not inherent in the use of conventional explosives, and thus they can be used only in areas where large explosions and associated phenomena can be tolerated. Stripping of coal with nuclear explosives does not appear practical at this time, but stripping overburden from copper or iron ore deposits may be a potential use. Even here, however, the use of nuclear explosives would require isolation, favorable topography, favorable ground-water conditions, and a low population density. If these basic requirements can be met, the use of nuclear explosives for overburden removal would offer both economic and time advantages. The possibility of using nuclear explosives for peaceful purposes was a subject for speculation as early as 1945. The PLOWSHARE Program was formally established by the AEC in June 1957 for the purpose of developing and demonstrating peaceful applications for nuclear explosives. The technical direction of the program is the responsibility of the Lawrence Radiation Laboratory, Livermore, Calif. Mining and excavation were two fields that received early consideration as areas in which nuclear explosives might be used. Knowledge gained from underground weapons testing increased this possibility, and the development of the thermonuclear device which has a small fission-to-fission ratio, reduced the hazard of radiation, and spurred interest. Nuclear explosives appear to have the greatest potential in the following mining operations: 1.— Surface Mining a) Stripping of waste for open-pit excavation b) Breaking of ore in open-pit mining c) Quarrying d) Blasting for production of aggregate, riprap, etc. 2. — Underground Mining a) Block caving application b) Crushing of ore for in-situ leaching, etc. c) Preparation of underground waste disposal areas Of the potential applications, excavation is perhaps the most obvious and the best understood, and probably the most practical for use in the near future. Large quantities of rock and earth can be moved by proper emplacement of nuclear explosives, but economic and practical relationship must be determined between the known capabilities of nuclear explosives and the required excavating to remove overburden. REMOVING OVERBURDEN IN OPEN-PIT MINING Removing the overburden is one of the largest jobs in open-pit mining. In 1960 open-pit mines produced approximately 130 million tons of coal, 108 million tons of copper ore, and 135 million tons of iron ore. To obtain this much production, an estimated 3-billion tons of overburden were removed from the coal, 216 million tons from the copper ore, and 135 million tons from the iron ore. These figures do not include the initial stripping required before ore production. For example, the ASARCO Mission mine started stripping operations in August 1959 and by mid-November 1961 had removed 46.3 million tons of material including 1.2 million tons of ore.* Initial excavation of this type offers the most favorable conditions for utilizing the earth-moving ability of nuclear explosives. EXPLOSIVE CASTING FOR REMOVING OVERBURDEN The use of explosives to remove overburden is not a new idea. Conventional explosives have been used for this purpose for many years with varying degrees of success. Several small coal strip operators have used this idea to increase production. At these mines about one-third or more of the overburden is thrown by explosives across the pit and onto spoil piles. The additional costs of drilling more blast holes and more explosives are more than compensated for by a reduction in the time required to uncover the coal, and by an increase in coal production.

Jan 1, 1964

By A. W. Peake, F. O. Prior

Considering the great advance in the development and application of electricity, it is not strange that eventually a big field for its use has been found in oil-field operations. So far as is known, the first electric drive in oil-field operations was in the Russian field of Baku in 1900. The first application in this country was made by the South Penn Oil Co. near Folsom, West Va. in 1903. In 1916, electric power was first used in the Burma fields of India for drilling and pumping. Between 1916 and 1922, The Empire Gas & Fuel Co. made the first large electrical installation in the Mid-Continent fields. But although the first application was made 27 years ago, it is only within the last 10 years that oil companies have begun to look upon its use with much favor. Within the last few years, there has been a steady increase in the use of electricity in the oil fields. The first application of electricity for oil-field operations in Wyoming was in the Lander field in 1919; the second was in 1924 in Salt Creek; and the third, and last to date, was made by the Continental Oil Co. in the Big Muddy field during 1926. Lander Field The electrification of oil-field operations in Wyoming was initiated by J. W. Steele, superintendent of the Producers & Refiners Oil Corpn., in the Lander field in 1919. At that time, 32 wells were being pumped from five band-wheel powers, with oil engines as the prime movers. Eight barrels of fuel oil were used for power per day and at the price of 90 c. per bbl. the fuel bill was $36 per day. It was decided to try a 15 to 35-hp. oil-field motor on one of these powers. Electric power was generated with steam at the old Wind River refinery station. This test was so successful that in 1920 all five powers were equipped with 15 to 35-hp. oil-field motors, the power being obtained from the Sinks Canyon hydroelectric station. Four of these powers pumped wells at an average depth of 1450 ft., and the fifth pumped wells at an average of 2100 ft. In 1920, the average production per day from the 32 wells was 325 bbl. The power bill on the

Jan 1, 1928

By A. CHESTER BEATTY

SO much has been written about African, and particularly about Northern Rhodesian, copper during the past two years that I feel safe in assuming that you are familiar with the general background of the Rhodesian picture. Therefore, I will confine myself to certain of the high lights in connection with the history, geology, development, ore reserves, and contemplated mining methods in this relatively new and highly important copper field., Unlike most of the other great orebodies of the world, the Roan Antelope mine was not discovered by the hoof of a starving prospector&apos;s faithful burro; nor even, as its name might suggest, by a well-placed kick of protest from an antelope stumbling over a malachite outcrop. Late in 1905 an English prospector named Collier, traveling in the N&apos;Dola district, came upon some natives using a green powder for medicinal purposes. Closer examination of the powder revealed that it &apos; was ground-up malachite. Collier endeavored to persuade the natives to tell him where they obtained this medicine, but&apos; for a long time without success, because of the general feeling among the natives that they did not wish to reveal the resources of their land to the white. Finally however, - he persuaded- brie &apos;of-the elders to at" least take &apos;him part way toward, the- place where the malachite was supposed to occur. The bid took him, to a point on the lower regions of the Luanshya river and there left him with the instructions that if he followed the stream up toward its.

Jan 1, 1931

By George S. Koch

Since 1882, world zinc production has increased. In contrast, US zinc production rose until about 1915, but since then has remained nearly constant, with a slight tendency to decrease. Production from the Tri-State district, the largest early source of zinc in the US, has gone down steadily; this decline has been balanced by a growth in the rate of other districts. These changes in US production are due to economic, not geological, factors. Recent exploration has located large minable ore bodies: additional deposits will undoubtedly be found in the stratabound carbonate rock and volcanogenic environments. A statistical analysis of the exploration effort in the Middle Tennessee district indicates that new discoveries can be expected there. Thus, the US is in an early stage of the production cycle for zinc. Of major mining districts in the US, only the Tri-State is exhausted under current economic conditions; large zinc resources of low-grade material, which would repay mining at higher prices or improved technology, are known to exist in that district .

Jan 1, 1982

By K. E. Brown, J. P. Brill, A. R. Hagedorn, T. C. Doerr

A recent correlation for multiphase vertical flow by Hagedorn and Brown1,7 has been used to examine the effect of numerous variables such as pipe size, gas-liquid ratio, liquid flow rate, liquid viscosity, liquid surface tension, oil API gravity, water cut, etc., on flowing pressure gradients. Most previous correlations were derived by using a form of the general energy equation which assumed negligible changes in kinetic energy. Under certain flow conditions this can lead to serious errors in predicting pressure traverses. Examples of traverses calculated both with and without the kinetic energy term are included here. The Chew and Connully correlation for calculating changes in viscosity with changing pressure and temperature has been extended so that the effect of a changing viscosity with depth on pressure gradients can also be predicted. Examples illustrating the effect of tubing size show the importance of this correlation in determining pipe sizes for initial well completions. Limitations on production rates in small pipe sizes from excessive friction losses can be predicted with greater accuracy. The combined use of a vertical-flow correlation with a horizontal-flow correlation provides a method for determining the maximum flow rate possible from both flowing and gas-lift wells. Examples are included to illustrate application of the combined use of vertical and horizontal-flow correlations in optimizing production rates and minimizing excessive costs from over injection of gas in gas-lift wells. INTRODUCTION The problems of multiphase vertical and horizontal flow are immediately encountered in any producing well. Fig. 1&apos; shows three stages of production: flow in porous medium, vertical flow and horizontal flow. All three stages affect the production rate from a well. If we are confronted with a particular well and consider only the variables involved in the vertical and horizontal stages of Fig. 1, we should be capable of calculating the flowing bottom-hole pressure necessary to produce a particular flow rate. A change in any of the variables results in a new solution to the problem. Recent approaches in developing horizontal and vertical-flow correlations have improved to the extent that the solution can now be obtained with more confidence than previously. VERTICAL AND HORIZONTAL FLOW CORRELATIONS Since Poettmann and Carpenter&apos;s&apos; original work in multiphase vertical flow, there have been many additional vertical-flow correlations developed which have greatly improved the accuracy of pressure-loss calculations. These

Jan 1, 1967

By Donald W. Scott

This paper describes the application of ore-dressing methods to the reclamation of milled frit from over-spray, or waste, porcelain enamel. Frit is the name given by enamelers to a granulated glass produced by the smelting and subsequent water quenching of various ingredients capable of forming a glass, usually including a compound to produce opacity. It is the major component of porcelain enamel, and normally commands a price ranging from 7 to 12 cents a pound. In the *preparation of a white enamel slip, usually 6 or 7 parts of clay, 2 parts of opacifier, small amounts of electrolytes, in some cases inorganic color stabilizeis and organic dyes, and 35 parts of water are added to 100 parts of frit; the mixture then is milled to a fineness of the order of 92 to 95 pct through a 200-mesh sieve. The frit forms the base of the enamel; the opacifier imparts opacity or reflectance; the clay suspends the frit while in slip form and serves as a binder in bisque form (dry and unfired); and the electrolytes control the workability. Spraying is used commercially, in many cases, to apply the finish coat of enamel to the ware, prior to drying and firing. In the spraying operation, only about 50 pct, by dry weight, of the enamel slip adheres to the surface of the ware, the remainder forms the over-spray. From 1/2 to 2/3 of the overspray goes up the flue where it is lost or recovered, depending on whether the plant is equipped with a dust-collecting installation; the coarser portion of the over-spray is collected in the spray booth. The former product is termed flue reclaim enamel, and the latter booth reclaim enamel. Although the spraying operation is done in specially constructed booths, which are partially or completely enclosed, it is extremely difficult to keep out contaminating dirt, which joins the reclaim. Some present-day large enameling plants use 20 tons of frit a day, of which 10 tons go into reclaim with a potential value of $1400 to $2400. When two-coat finish enamels were common, the reclaim was used satisfactorily for the undercoat, but the relatively recent advent of one-coat finish enamels prevented use of the reclaim because, even when blended with first-run enamels, it gave dirty finishes with poor gloss. It was thought that the pitting and specking encountered with reclaimed enamels were caused by the contaminating dirt, and that the poor gloss was caused, primarily, by the high clay content; more clay usually was added to give proper suspension properties to the slip when the reclaim was used. A clay content in excess of about 10 pct usually imparted refractoriness to porcelain enamels. Present-day one-coat porcelain enamels must combine high gloss and opacity with freedom from surface defects. Methods of beneficiating the over-spray,

Jan 1, 1948

By Donald W. Scott

This paper describes the application of ore-dressing methods to the reclamation of milled frit from over-spray, or waste, porcelain enamel. Frit is the name given by enamelers to a granulated glass produced by the smelting and subsequent water quenching of various ingredients capable of forming a glass, usually including a compound to produce opacity. It is the major component of porcelain enamel, and normally commands a price ranging from 7 to 12 cents a pound. In the *preparation of a white enamel slip, usually 6 or 7 parts of clay, 2 parts of opacifier, small amounts of electrolytes, in some cases inorganic color stabilizeis and organic dyes, and 35 parts of water are added to 100 parts of frit; the mixture then is milled to a fineness of the order of 92 to 95 pct through a 200-mesh sieve. The frit forms the base of the enamel; the opacifier imparts opacity or reflectance; the clay suspends the frit while in slip form and serves as a binder in bisque form (dry and unfired); and the electrolytes control the workability. Spraying is used commercially, in many cases, to apply the finish coat of enamel to the ware, prior to drying and firing. In the spraying operation, only about 50 pct, by dry weight, of the enamel slip adheres to the surface of the ware, the remainder forms the over-spray. From 1/2 to 2/3 of the overspray goes up the flue where it is lost or recovered, depending on whether the plant is equipped with a dust-collecting installation; the coarser portion of the over-spray is collected in the spray booth. The former product is termed flue reclaim enamel, and the latter booth reclaim enamel. Although the spraying operation is done in specially constructed booths, which are partially or completely enclosed, it is extremely difficult to keep out contaminating dirt, which joins the reclaim. Some present-day large enameling plants use 20 tons of frit a day, of which 10 tons go into reclaim with a potential value of $1400 to $2400. When two-coat finish enamels were common, the reclaim was used satisfactorily for the undercoat, but the relatively recent advent of one-coat finish enamels prevented use of the reclaim because, even when blended with first-run enamels, it gave dirty finishes with poor gloss. It was thought that the pitting and specking encountered with reclaimed enamels were caused by the contaminating dirt, and that the poor gloss was caused, primarily, by the high clay content; more clay usually was added to give proper suspension properties to the slip when the reclaim was used. A clay content in excess of about 10 pct usually imparted refractoriness to porcelain enamels. Present-day one-coat porcelain enamels must combine high gloss and opacity with freedom from surface defects. Methods of beneficiating the over-spray,

Jan 1, 1948