Search Documents

By T. O. Allen, J. H. Atterbury

Laboratory and field tests during the past five years indicated considerable variation in the penetrating power of commercially available gun perforators. Many of the guns which achieved inadequate penetration in these tests have since been improved. However, recent productivity tests indicated the possibility of inadequate penetration or, at least, ineffective penetration in some wells. Laboratory experiments under simulated well conditions have demonstrated considerable plugging of the perforations, apparently as a result of factors associated with the shooting process and/or the drilling mud in the well at the time of perforating. The restrictions to flow per unit of hole depth caused by this plugging appears to be greater for jet perforators than for bullet guns of comparable diameter; however, because of the greater depth of penetration obtained with the jet guns, the total flow rates appear to he approximately equal. Limited testing with an experimental shaped charge suggests that less shot hole restriction and greater flow rates may result from larger-diameter perforations or other factors related to charge design. INTRODUCTION Gun perforating has been accepted for a number of years as a routine well completion method which is often preferred since it permits more selective operation of producing zones. Nevertheless, questions have continued to arise as to the effectiveness of the communication paths established between the productive formation and the interior of the casing. The basis for these questions has generally been failure to obtain anticipated fluid production rates through gun perforated completions in specific wells. These low productivities, together with the frequent recovery of bullets from well bores, were considered strong evidence of inadequate penetration. Laboratory investigations of the penetration performance of many of the bullet guns available as late as 1948 gave support to these indications. Subsequent electrical analog studiesl,2,3 indicated that the depth of penetration required to provide productivities equivalent to open hole was beyond the capacity of most bullet perforators evaluated in the early laboratory penetration tests. These results, together with the advent of the shaped charge in the field of oil well perforating, stimulated the interest of both oil operators and service companies in gun development. Improvements in gun design resulted in jet and bullet guns which appeared to be capable of providing sufficient penetration for most perforating jobs. However, some wells failed to yield satisfactory fluid production even after being perforated with the more powerful guns, again raising the question as to the effectiveness of the perforating operation. This fact, together with preliminary shooting into targets prepared with formation cores, indicated that factors associated with the perforating process and/or the fluids in the well bore at the time of shooting may reduce effective formation penetration and thereby decrease well productivity. These laboratory and field data prompted another phase in the investigation of the effectiveness of gun perforating: a program to determine the extent and seriousness of perforation plugging under simulated well conditions.

Jan 1, 1955

By F. Keller, E. H. Dix, L. A. Willey

The consideration of alloying elements for aluminum has led to a series of investigations of the equilibrium relations between aluminum and those alloying elements. Therefore, the aluminum end of the aluminum-antimony diagram has been studied. The general form of the aluminum-antimony equilibrium diagram has been worked out by Campbell and Mathewsi and by Tammann.2 Canlpbell and mathews described principally the beginning of solidification. They found the curve of beginning of solidification rising gradually from the melting point of pure alunlinum to a maximum at about 67 per cent. aluminum. After a slight lowering of the curve at a little greater antimony concentration the curve again rises to a maximum at 18.4 per cent. aluminum, which corresponds to the compound AISb. The curve then drops to the melting point of pure antimony. Tamrriarln explained the maximum occurring at about 67 per cent. aluminum as the result of the slow formation of the single compound AISb. The space lattice of the compound AISb, according to Owen and Preaton,³ is face-centered cubic, the antimony atoms being intermeshed with an identical aluminum lattice. Very little, if any, work has been done on aluminum alloys containing small amounts of antimony. The Present Investigation It has been the purpose of this investigation to determine the solid solubility of antimony in aluminum and also to investigate the eutectic temperature and concentration. The experimental work has been carried out in a manner similar to that described in a previous paper4 from this laboratory.

Jan 1, 1931

The Ortiz Mountain property is located approximately 40 km (25 miles) southeast of Santa Fe and 13 km (8 miles) from the village of Cerrillos. The property embodies a Spanish mineral grant from which Gold Fields acquired about 2, 200 hectares (900 acres of surface and mineral rights. Following a period of exploration, metallurgical testing and development of a feasibility study in 1974, the decision was made, because of the higher gold price in the fall of 1978, to place the property into production. the gold is confined in a quartzite breccia; it is an unusual occurrence because the gold in this host rock is leachable at minus 19 mm (3/4 in. ). Total ore reserves are estimated at approximately 3.6 million mt (4 million st) averaging 1.89 g per mt (0.055 oz per st) based on a cut-off of 0.7 g (0.02 oz). The ore will be recovered by open pit mining at a stripping ratio of 1. 2:l. Production is scheduled for 13,600 mt (15,000 st) of ore per week or approximately 680,000 mt (750,000 st) per year. Primary crushing of pit-run material is by a 1,070 by 1,015 mm (42 in. by 40 in.) jaw crusher. Crushed ore is conveyed to stockpile and then to a 2.13 m (7 ft) standard crusher with the screened over- size crushed in a 1.5 m (5 ft) tertiary cone crusher. The screen undersize, the final product for leaching, is minus 19 mm (3/4 in. ). A 1, 360 kg (3,000 lb) sample is cut from the crushed ore stream, further crushed in a small jaw crusher and then sampled in two more stages by Vezin samplers to produce a final 13.6 kg (30 lb) sample for assaying. Pebble lime is then added to the ore on the belt as it is sent to the conveyor gantry spanning the leach pads. A tripper on this moving gantry stacks the leach ore without compaction. The entire crushing plant and conveying system is of open-air construction. Leach pads have a total length of 515 m by 60 m (1,700 ft by 200 ft) wide with usable dimensions of 490 m by 58 m (1,600 ft by 190 ft). The directional length slope is 3. 870 with 370 on the width. The pad is constructed of 175 mm (7 in. ) thick asphalt containing a rubberized asphalt membrane. It is divided by a 300 mm (1 ft) high curb into eight segments. Each segment is loaded with 13,600 mt (15,000 st) of ore, which is one week's production. Optimum working height of a pad is considered to be 3. 0 m (10 ft) with a maximum height of 4. 0 m (14 ft).

Jan 1, 1981

By T. V. Moore

DURING 1910, crude-oil production in the United States reached a record level averaging about 3.700,000 barrels daily. Export declined sharply while imports increased with the result that large quantities of crude oil were run to storage during the year. Imports consisted largely of residual fuel oil brought in from South America bit because of a shortage of that product in this country and of Mexican crude. The price of petroleum products followed the declining trend of the last three year resulting in serious disparity between crude and product prices. This condition was aggravated in some areas by the increasing production of distillate by recycling operations and by the high tanker rates prevalent in the last two months of the year. As a result two small purchasers found it necessary to reduce crude-oil price in the Corpus Christie area of Texas.

Jan 1, 1941

By Jasper L. Stuckey

PYROPHYLLITE, first identified as soapstone,1 later as agalmatolite,2 and finally as pyrophyllite,3 has been known to occur in North Carolina for more than 130 years and has been produced intermittently in commercial amounts for the past 100 years. Pyrophyllite mining, however, has become a major industry in North Carolina only during the past 25 years. North Carolina and California are the chief producing states. Current annual production averages 125,000 tons, of which slightly more than 90 pct comes from North Carolina. Distribution and Geologic Setting: All known pyrophyllite deposits in North Carolina are associated with rocks of the Carolina Slate Belt,4 which is composed of a vast series of metamorphosed volcanic and sedimentary materials, occurring as two zones extending in a northeast-southwest direction across the state. The larger of these zones, lying in the central Piedmont region, varies from 8 to 50 miles wide. The smaller zone lies along the eastern edge of the Piedmont region and is partly covered by coastal plain sediments.

Jan 1, 1958

By Frances Hurd, Clark

Iv 1897, Roberts-Austen(l)$ found an arrest in the thermal curves of alloys of 60 per cent. copper and 40 per cent. zinc. This break occurred from 450° to 470° C. Shepherd, (2) working in 1904, was unable to detect any change in the direction of the thermal curve. In 1911, Carpenter and Edwards(3) confirmed the work of Roberts-Austen and called this a eutectoid transformation of beta to alpha plus gamma. Hudson') in 1914, showed that the beta constituent could be produced synthetically at temperatures below the transformation point. He believed the change in the beta was polymorphic in nature rather than a eutectoid. The work of Matsuda(32) in 1922 demonstrated this break by thermal analysis, microscopic investigations, dilatation, electrical resistance measurements, and a thermoelectric study. He believed the transformation to be continuous from 300° to 480° C., and comparable to the A 2 transformation in iron. Later, in 1924, Andrew and Hay, with electrical resistance measurements, confirmed Matsuda's work. Imai(28) showed the transformation to be progressive and therefore a function of the temperature rather than the time. He stated that it was neither a eutectoid nor an allotropic change of phase. Atomistically expressed, it was a change, not of atomic configuration, but of atomic energy of some kind; and again it was compared to the A 2 transformation in iron. Imai believed that his analyses by X-rays led to the same conclusion. In order to study this change, at 470'C., in homogeneous 60:40 brass, Homerberg and Williams «0> and Homerberg and Shaw(41) quenched their material in iced brine to obtain the beta solid solution and reheated at various temperatures. At 200° C., a change in the microstructure and physical properties occurred. A fine-grained structure, which they termed alpha and which had the appearance of a sorbitic steel, appeared, with an increase in the tensile strength to 82,750 lb. per sq. in., and a Brinell ball hardness of 240 with 3000 kg. load. At 470° C., the alpha

Jan 1, 1927

By Louis D. Huntoon

CANADIAN gold production is forging ahead annually and the prospects are that it will continue to do so for many years. Table 1 shows recent annual increases. Production for 1933 will probably reach $70,000,000, and further increases are likely in 1934 and 1935. (Data for November and December, 1932, are estimated throughout this article.) The depression sent many prospectors to the woods so during the last two years many new gold areas have been discovered and are attracting real capital for exploration and development. Several mills came into production in 1932 and mills now under construction will start production in 1933. The offices of mining lawyers are busy. Capital for this new work is obtained from well financed mining companies, syndicates, and individuals who were fortunate enough to invest in the dividend-paying gold mines of the north country in the early days. Prospectors and capital are cooperating. An interest is always retained by the prospector or vender and usually a small amount of real money is given the prospector.

Jan 1, 1933

By B. Wilshire, P. W. Davis

It has been shown that grain-boundary migration during high-temperature creep can reduce or even prevent the formation of intercrystalline voids, giving a considerable increase in ductility.' A similar observation has been made in a recent investigation of the creep properties of various grades of nickel and nickel alloys. The results can be illustrated by the observations made on: a) Pure vacuum-cast nickel (99.993 pct Ni) b) Impure vacuum-cast nickel (99.97 pct Ni) c) Pure nickel containing internal voids (produced by a process of intering). d) A substitutional solid solution alloy of pure nickel containing 1.16 pct Sn. All the materials were given a high-temperature anneal (>850°C) to produce a stable grain size of 7 to 10 grains per linear mm. The apparatus and techniques used to obtain the present results have been described elsewhere.' In this series, grain growth was observed only in the highest-purity, vacuum-cast metal. Thus we may consider that in the other materials grain-boundary migration was prevented by either preexisting voids or solute atoms. The effect of migration on the creep ductility of the above materials can be seen from Fig. 1, which

Jan 1, 1962

By H. P. Willard, R. W. Gates

Basic Inc., has been mining magnesite and brucite for 27 years at Gabbs, Nev. This is a medium sized open-pit mine. The magnesite deposits are in north-western Nye County about 30 miles east of Luning, Nev., on the west slope of the Paradise Range, at an elevation between 5000 and 6000 ft. The magnesite and associated brucite is used to make magnesia refractories employed principally in the steel industry and magnesium oxide for various chemical uses.

Jan 10, 1963

By A. T. Yu

On March 18, 1964, the 52,000 dwt ore carrier M/S Houn Maru called at the port of Coquimbo, Chile, on its maiden voyage to take iron ore to Japan. This marked the first time a vessel of this size ever arrived at Coquimbo, and the event promises to drastically accelerate henceforth iron ore exports from Coquimbo province. This was made possible by the use of a versatile shiploading system recently installed by Cia. Minera Santa Fe. Coquimbo has no mechanized loading facilities other than six conventional 5-ton cargo cranes. Limited space on shore further complicates the stocking problems. To make the best of what is available, a meticulously organized semi-hand-loading system has been developed through the years.

Jan 5, 1964

Discussion of the paper of Robert Henry Lee, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 82, October, 1913, pp. 2515 to 2522. J. E. JOHNSON, JR., New York, N. Y.:-This subject is of great and increasing importance, as the exhaustion of the deposits of ore of ideal character compels the iron industry to turn more and more to those which are less desirable on account of physical structure as well as analysis. Thus there has come about the use of the Mesabi ores in this country and also of the Minette ores in Europe, which produce far greater percentages of flue dust than did the lumpy ores first used. It is a matter of common knowledge that the utilization of this flue dust, containing commonly 50 per. cent. or more of metallic iron, has been a problem very difficult and tedious of solution. The number and variety of the solutions now offered is a sufficient proof of this. . I have no intention of going into the merits or demerits of any of these processes as such, but there are certain considerations concerning the effect of their product on the operation and fuel economy of the blast furnace which I believe to be new and which I desire to bring out. There are two methods, so different as almost to be direct opposites of each other, whereby an ore may exercise an unfavorable effect on the economy of the blast furnace. The first of these is well known and results from the ore being refractory and highly resistant to the action of the reducing gases of the blast furnace. This results in its being incompletely reduced when it reaches the zone of fusion and in the reduction being finished by the direct action of carbon in the lower portion of the furnace. This is so well understood as to need little elaboration or comment. There is, however, another action which may be equally as fatal to the economy of the furnace as the foregoing, and as this point is, to the best of my knowledge, not generally appreciated, it is one upon which I desire to lay particular stress. This consists in the ore being, in a sense, too reducible.

Jan 12, 1913

By Dean F. Winchester, C. D. Johnson

The so-called Rocky Mountain region is here made to include Colorado, Idaho, Montana, northern New Mexico, Utah and Wyoming, an area of great distances and relatively sparse population. Conditions of distance, transportation and markets have had their retarding influence on devolopment and production but the increase in facilities and markets in recent years has provided additional incentive for more thorough search for new productive areas and the more complete development of the known fields. The low prices of crude during the past year have offset, to a certain extent, the desire for increased production and much of the effort has been directed therefore to outlining new areas rather than to attempts to increase production from known fields and thereby add to the already sufficient supply above ground. During the year just closed the Rocky Mountain region has seen consistent efforts to outline new areas and these efforts have been reasonably successful. In this area a very large part of the land is government property, and by cooperation between the government, the private owner and the company it has been possible to carry on development in a scientific manner, providing for the maximum recovery of valuable products at least cost and at times when prices were best. Due to the fact that in the Rocky Mountain region costs of exploration and development are relatively high because of natural circumstances, it has been the policy of operators to drill test wells only on structures where they controlled a large proportion of the land. Even community lease programs have been effected in certain areas, thus obviating the necessity of offset drilling and the attendant uneconomical and even wasteful production. Oil production in the Rocky Mountain states has shown a slight increase during the year, the average daily production for November being 78,124 bbl. as against an average in January of 76,681 bbl. The total production during the first 11 months of the year, according to the U. S. Burcau of Mines, was as follows:

Jan 1, 1929

By L. A. Price

With increased stripping ratios and with dwindling ore content, the mining fraternity is increasingly turning to larger and larger equipment for profitable open pit operations. The availability of higher horsepower prime movers and increased-capacity electric transmissions using either wheel-mounted or axle-mounted traction motors makes a reality of single-axle, rear dump trucks having 150 to 250 ton capacity. The size of electric loading shovels is inherently geared to the size of haulage equipment. To work effectively with this new generation of trucks, the Harnischfeger Corporation has introduced its P&H Model 2800 with a capacity of 20 to 25 cu yd and a working weight of nearly 1,500,000 lb. The Model 2800, depicted in Figure 1 loading a 200 ton truck, has many new electric and mechanical features designed to give excellent production and low cost operation. Chief among the new features is the ELECTROTORQUE control system. Electrotorque is a completely static, solid state electronic system supplying controlled power both to the armatures and to the fields of the d-c shovel drive motors. It eliminates many major electrical rotating machines and their attendant maintenance. The system was developed jointly by ASEA of Sweden and Harnischfeger Corp.

Jan 1, 1970

By Sherwin F. Kelly

Twenty five years of exploration has shown that the "geophysical dollar" is worth $1780 in the Orange Free State, $1488 on the Witwatersrand, $85 in Sweden, $28,000 in the Transvaal and $3500 or more in the U.S.

Jan 6, 1951

By M. K. Seguin

The study described in this paper is first centered on the determination of the physical properties (gravimetric, magnetic, electrical, and electromagnetic) o f metamorphosed iron ores of the Carol Lake-Labrador City District. Different geophysical surveys available in the Carol Lake-Wabush area were interpreted quantitatively and the dimensions, attitude, and tonnage of the ore bodies investigated were determined. A geophysical-statistical study was undertaken which permitted the determination of the grade of iron, magnetite, and, subsequently, specularite in the ore bodies. A discussion of the theory and logical progression of the study and the application of the results to actual geophysical data is presented. The conclusions, which are of real significance from the economic standpoint, may be predicted from the data obtained from geophysical surveys before any diamond drilling is undertaken. An integrated interpretation of this type is useful in planning future exploration work and selecting the most favorable geological structures. It also serves as a guide to minimize and determine tonnage drilling patterns. The general conclusion that a restricted range of residual gravity and magnetic anomalies are a key to exploration is valid. Indeed large depths to the top of deposits are absent since all the ore bodies are overturned synclinal structures with tops located close to the surface. Certain irregular geometries do occur but they are not common and the alignment of the iron ore bodies is sub parallel so that magnetic anomalies are evenly reduced in the earth's magnetic field vector.

Jan 1, 1975

Executive JOHN M. LOVEJOY, Chairman ERLE V. DAVELER G. B. WATERHOUSE WISER JUDSON WILLIAM WRAITH J. V. W. REYNDERS, Consultant Finance HENRY KRUM, Chairman PAUL D. MERICA R. M. ROOSEVELT H. G. MOULTON, Consultant Admissions. RALPH M. ROOSEVELT, Chairman GEORGE D. BARRON, Vice-chairman JOHN L. CHRISTI PHILIP KRAFT W. A. SINSHEIMER

Jan 1, 1936

By J. A. Morgan

IN the art of roasting sulfides it is well known that the lower the temperature and the higher the pressure of SO, the larger will be the amount of sulfate present in the product. However, the mechanism of sulfate formation is not generally understood. The following experiment" demonstrates in a direct way that, in the roasting of Cu2S, the sulfate forms from the reaction of Cu2O, formed by the oxidation of Cu2s, with gaseous SO, (or SO3) and 0,. Thus, the sulfate does not form at the sulfide surface. The reaction at the sulfide surface is the same whether or not sulfate is formed. Using an indirect method, Ong, Fassell, and Wadsworth' infer that sulfate forms after oxidation, during the roasting of sphalerite, agreeing with the observations of this paper. The method presented here of demonstrating that sulfate forms after formation of Cu2O is to roast a sample of Cu2S and then to locate and identify the phases formed.' A solid cube of cuprous sulfide, made by melting Fisher reagent grade Cu2S powder and measuring about 1.5 cm on edge, was placed on a Nichrome wire grid suspended over the top of an Alundum combustion boat. The assembly was placed in a tube furnace at 600°C and oxygen gas, flowing at 0.60 liters per min, was passed around the specimen for 24 hr. The furnace tube diameter was 1.5 in. The partially roasted sample was removed from the furnace and impregnated with resin No. BR 0014, obtained from the Palmer Products Co., and the impregnated sample was then mounted in Lucite. A cross section was obtained by grinding and the surface was prepared by the following steps: 1) grinding—60 grit, 3M disk, dry; 2) preliminary polishing —60 through 600 grit, 3M disk, dry; 3) polishing— 8 µ diamond putty, silk cloth; and 4) final polishing —1evigated magnesia in isopropyl alcohol, Selvyt cloth. The color micrograph of the polished surface is shown in Fig. 1. The layers present in the micrograph are given along the side. The comwositions of the various layers were established by Debye-Scherrer patterns. From this evidence the following sequence of reactions which occur in the roasting of Cu2S is inferred: 1) The oxidation of Cu2S occurs with oxygen which has been transported through the oxide-sulfate layer by either gaseous or solid state diffu- sion. The products of this reaction at the Cu2S surface are Cu2O and SO,. 2) The SO, diffuses out through the pores in the Cu2O and finally reaches a position in the Cu2O where the oxygen pressure and the SO, pressure have values such that the thermodynamic conditions for the formation of CuSO4 are fulfilled. Then, the mixture of SO2, SO3, and oxygen reacts with the Cu2O to form CuSO1. 3) The CuSO, decomposes by the evolution of SO,, or SO, and O2, to form the basic sulfate. This is reasonable, since the SO, gradient will decrease toward the oxygen gas phase from the CuSO4 layer. 4) For this same reason the basic sulfate will decompose to form CuO. The above sequence of events is based on the assumption that diffusion through the oxide and sulfate layers, rather than the reaction at the sulfide-oxide interface, is rate-determining. This assumption is supported by the observation that these oxide and sulfate layers combined are almost nonperme-able to the flow of gases through them. Acknowledgments This research was supported by the U. S. Air Force, through the Office of Scientific Research of the Air Research and Development Command. The authors wish to acknowledge the helpful suggestions of Ralph Wells of the Applied Research and Developmeit Laboratory, U. S. Steel Corp. References E. A. Peretti: A New Method for Studying the Mechanism of Roasting Reactions. Discussions Faraday Soc. (1948) 4, p. 174. - J. N. Ong, Jr., M. E. Wadsworth, and W. M. Fassell. Jr.: Kinetic Study of the Oxidation of Sphalerite. Trans. AIME (1956) '206, pp. 257-263; Journal OF Metals (February 1956).

Jan 1, 1957

By D. N. Dietz

Jan 1, 1969

By L. A. Updegraff

Before discussing the application of capacitance for the measurement of moisture content in a moving stream of coal it might be well to first give a brief description of the process and then show how it can be applied to the coal industry. A capacitor may be described as a device having two conductors separated by an insulator, the conductors hereafter being designated as a test cell or test plates and the insulator as the dielectric. Capacitance, therefore, is a measure of the ability of a capacitor to store an electrical charge. Two basic factors that affect capacitance are the dimensions of the capacitor and the dielectric constant of the insulator. Capacitor dimensions which affect its capacity are the area A of the conductive surface, and the distance d between plates. Capacitance is inversely proportional to the distance between plates and directly proportional to area A, so if capacitance is indicated as C and the dielectric constant as K the equation for capacitance would be C = AK/d. The dielectric constant can be described as the ratio of the actual capacitance of any given material to that of a vacuum, which is unity. In industrial applications the area of the plates remains constant as also does the distance between them, leaving the dielectric constant as the only variable to affect the capacitance measurement. Figure 1 is a schematic diagram of an r-f excited capacitance bridge in which a test cell is part of the circuit. This bridge consists of four capacitors in two pairs connected across an a-c voltage source. In one side of the circuit the two capacitors are fixed but in the other side they are variable, one being the rebalance capacitor operated by the servo motor and the other the test plates between which the dielectric passes. Capacity of the plates is a function of the dielectric constant of the material between them and is measured at radio frequency. Within the recording instrument is an r-f oscillator and a 60 c ps modulator. The radio frequency signal is generated by the oscillator, modulated by a 60 cps wave, and sent to the bridge. Therefore the signal entering the capacitive bridge is a radio frequency carrier with a 60 cycle envelope, If the bridge is in balance as the signal enters there would be no voltage drop and so no output by the detector. As long as the dielectric constant remains the same the bridge will stay in balance. However, any change in the dielectric constant, which in this case would be a change in moisture content, would affect the bridge. Higher moisture increases the capacity of the test cell which causes less voltage to develop across it causing imbalance of the bridge. This in turn causes a radio frequency signal to appear at the detector. Output from the detector is a 60 cycle ripple which is in proportion to the imbalance of the circuit. A 60 cycle amplifier boosts the detector signal to enough power to drive the servo motor which positions the recording pen and also rotates the variable capacitor, to which it is mechanically connected, to bring the bridge back in balance. An increase in moisture causes the servo motor to rotate in one direction, but a decrease causes imbalance in the opposite direction, and thus rotates the motor in that direction. This brings the bridge back in balance and stops the motor. The bridge shown in Figure 1 has been modified so as to provide a wide range of adjustments. Coarse and fine span adjustments located in the recording instrument are set to govern the amount of pen movement for a given change in capacitance. A measuring head unit contains coarse and fine zero adjustments for

Jan 1, 1961