Search Documents

By F. H. Bunge, W. H. Jr. Dailey

This paper covers an investigation of the magnetic roasting characteristics of several iron ores when treated in the form of small pebbles (1/8" to 1/2" in size), and in the form of balled fines. The roasting treatment was carried out with apparatus capable of very close control of time, temperature, face velocity, and per cent combustible in the reaction gas. The effect of rapid initial heating was not studied although it is believed that this has a major effect on the results when processing solid pebbles. The test equipment is a fixed bed type, with such a wide range of gas velocities, temperature, combustible content and etc., that the results obtained can be made to approximate those from various commercial roasting processes. The data presented in this report covers reaction rates, effect of processing variables on silica in the concentrate, flow resistance of beds, and to a limited extent, the effect of particle size. The work is far from complete and raises many more problems than it gives answers for. We believe, however, that much of the information will be useful to those engaged in investigation of magnetic roasting processes. We measured the time required for various degrees of completion of the reaction of hematite to magnetite, for finely pound material in balled form and for carefully sized crushed ore. Measurements were made for a variety of Minnesota and Labrador ores. This report covers an ore requiring fine ginding (-325 M) for liberation (Lower Kevin) and an ore requiring coarser grinding (-100 M) for liberation (Upper Olson). These ores represent approximately the range of characteristics for a group in the west end of the Mesabi Range. Our data shows that the reaction rate is very fast for the finely ground material and that tests are readily reproducible. The reaction rate of the larger size material, in the range of 1/8" to 1/2", is much slower and the results more erratic. We found that for the ores tested, the percentage of silica in the Davis tube magnetic concentrate was a function of iron recovery. Normally the concentrate had a low and relatively uniform percentage of silica up to a critical value of recovery. Above this critical recovery value the percentage of silica increased very rapidly. For example, for one particular ore roasted in the form of 3/8" diameter balls made from -28 mesh fines, the silica remained at about 7% to 8% until the recovery exceeded about 93%. Increasing the recovery beyond 93% resulted in over 25% silica with the additional recovery. The degree of conversion of hematite to magnetite (% completion of roast) required to obtain 93% recovery for balled material, varied inversely with the gas flow rate. Percentage silica in the concentrate resulting from roasting 3/16" and 1/2" solid material was relatively erratic. However, for varying degrees of iron recovery the lowest silica percentages corresponded to those obtainable when roasting fines. It is thought the probable reason for the erratic values was the variation in shattering or cracking of the pebbles during initial heating and roasting. There is some indication that very fast initial heating will greatly increase the permeability of the individual particles of ore to gas flow so that the reaction rate for coarse sizes will approach that obtainable with balled fine material.

Jan 1, 1961

By AIME AIME

A METALLURGICAL research building is to be erected for the Armour Research Foundation at the Illinois Institute of Technology. It will be located at the corner of Federal and 34th Sts., Chicago, and fully equipped will cost $250,000. It will provide the Middle West with the largest and most complete of facilities for the conduct of developmental and industrial research in this field. The new building will be constructed around an existing foundry and metallurgical research building which has become too small to carry on and service the many research projects contracted for by the Foundation, having to do with steel, alloys, and nonferrous metals. After two bays of the new unit have been completed, the old unit will be torn down and the new one completed.

Jan 1, 1942

By AIME AIME

UNTIL recently, practically all geophysical prospecting in Australia was conducted by government departments, either by the Aerial, Geological and Geophysical Survey of Northern Australia or the New South Wales Department of Mines. At present, in addition, the Shell company is carrying out an extensive geophysical campaign in South West Queensland. The Northern Australia Survey has now been in operation for over six years, its work being carried out principally in the northern and central parts of Australia over an area of about a million square miles. At present this Survey is being brought to a conclusion but it appears certain that the geophysical section will be transferred to a Commonwealth Government department on a permanent basis. At present the officers of the Geophysical Section are preparing or have issued some 150 reports on their field work and also a special technical report on the geophysical practice of the Survey.

Jan 1, 1942

By William E. Ford, Edward Salisbury Dana

Secondary Twinning. - When there is reason to believe that the twinning has been produced subsequently to the original formation of the crystal, or crystalline mass, as, for example, by pressure, it is said to be secondary. Thus the calcite grains of a crystalline limestone often show such secondary twinning lamella?. The same are occasionally observed (Ilc, 001) in pyroxene crystals. Further, the polysynthetic twinning of the triclinic feldspars is often secondary in origin. This subject is further discussed on a later page, where it is also explained that in certain cases twinning may be produced artificially in a crystal individual - e.g., in calcite (see Art. 282).

Jan 1, 1922

By M. J. Richards, A. Szirmae, G. R. Speich

The formation of austenite from ferrite, ferrite plus retastable carbide, spheroidite, and pearlite has been studied in a series of irons, Fe-C alloys, and plain-carbon steels using fast heating techniques. In the absence of carbide, austenite nucleates at ferrite/ferrite grain boundaries; nucleation is followed by the rapid growth characteristic of a massive transfornation. The trarnsformation occurs at 950°C at heating rates of 106º C per sec and cannot be suppressed. Metastable carbide dissolves before austenite forms and does not influence the transformation kinetics. For spheroidite structures, austenite nucleates preferentially at the jinction between carbides and ferrite grain boundaries. Growth from these centers proceeds until the carbide is completely enveloped; subsequent growth occurs by carbon diffusion through the austenite envelope. For pearlite structures, austenite nucleates preferentially at pearlite colony intersections. Carbide la)?zellae dissolve at the advancing austenite interface but complete solution of carbide does not occur; the residtial carbide is eventually dissolvled or spheroid-ized depending on the carbon cuntent. The magnitude and temperature dependence of the austenite growth rate into Fe-C pearlite when incomplete carbide dissolution is assumed are satisfactorily explained by an approximate colume diffusion model. The impurities present in plain-carbon steel reduce the growth rate of austenite in comparison to that jound in an Fe-C alloy. The formation of austenite has been studied in much less detail than the decomposition of austenite. This is primarily a result of the importance of harden-ability in determining the mechanical properties of steel. Recently, more interest in the kinetics of austenite formation has resulted from the discovery by Grange1 that rapid heating techniques strengthen steel by refining the austenite grain size. Although the strengthening effect is not large, it is accompanied by no loss in ductility. In addition, interest continues in rapid heat treatment of low-carbon steel sheet for tin plate applications.2,3 Among the few systematic studies of austenite formation are the early work of Roberts and Mehl4 on formation of austenite from pearlite and recent work of Molinder5 and of Judd and paxton6 on formation of austenite from spheroidite. Also, Boedtker and Duwez7 and Haworth and paar8 have recently studied the formation of austenite from ferrite in relatively pure iron, Kidin et al.9,10 have studied the formation of austenite in 8 pct Cr steels, and Paxton has recently discussed various aspects of austenite formation in steels." The present work was undertaken to determine the kinetics of austenite formation for a variety of starting structures including ferrite, ferrite plus metastable carbide, ferrite plus spheroidal cementite, and ferrite plus pearlitic cementite. Emphasis was placed on determining the active sites for austenite nucleation, determining the temperature and time range of austenite formation, and in the case of pearlite a careful study of the growth rate of austenite was made in the absence and presence of impurities. By using a variety of heating techniques including laser-pulse heating, it has been possible to study austenite formation in an isothermal fashion over a wide range of temperatures. EXPERIMENTAL PROCEDURE The alloys studied in the present work are a zone-refined iron with 4 pprn C, an Fe-C alloy with 130 pprn C, 2 Fe-C alloys with 0.77 and 0.96 wt pct C, and a plain carbon steel with 0.96 wt pct C. The zone-refined iron and Fe-C alloys contained 60 pprn and 200 pprn total substitutional impurities, respectively. The plain carbon steel contained 2400 pprn Si, 2000 pprn Mn, and 900 pprn Cr. Various heat treatments were given to these alloys to produce different starting structures of equiaxed ferrite, ferrite plus metastable carbide, fine pearlite, and spheroidite. These heat treatments are given in Table I. A wide range of heating rates were employed in this work because many of the reactions occur so quickly at temperatures in the austenite range that they are completed during the initial heating cycle unless very fast heating rates are used. Essentially the same heating techniques employed by Speich et a1.12 and Speich and Fisher13 were used in this work. For time intervals of 2 sec to 20 hr, simple hand immersion of 0.010-in. thick specimens in a Pb-Bi bath was employed. These specimens were quenched in a 10 pct NaC1, 2 pct NaOH aqueous bath. For time intervals of 100 m-sec to 2 sec, an automatic dunking and quenching device was employed with 0.002-in. thick specimens. Again, liquid Pb-Bi baths were used for a heating medium but now helium gas quenching was employed. For time intervals of 2 to 100 m-sec a laser heating device was employed with 0.002-in. thick specimens; a helium plus fine water-droplet spray was now used for quenching. Additional information on heating times shorter than 2 m-sec was obtained by study of the zones around the centrally heated laser spot. Here diffusion of heat from the centrally heated zone raises the temperature of the specimen locally to all temperatures between ambient and the peak temperature, but for times of the order of microseconds. All the heat-treated specimens were examined by

Jan 1, 1970

By K. Heindlhofer

Estimates of the "plasticity" of a metal are commonly deduced from three types of test—tensile, torsion and impact. The several results have been more or less at variance, though this disparity has attracted little notice, largely perhaps because they have been expressed in different terms. The discrepancy between the results of the three tests becomes obvious when each is made at a series of low temperatures, for the temperature range within which the "plasticity" of iron largely disappears proves to be very different in the three types of test. The rather abrupt disappearance of "plasticity" of iron within a narrow temperature range cannot be due to any physicochemical change (such as a precipitation) taking place in the material at that time, because the original plasticity is immediately regained when the temperature of the material is brought above the sensitive range. Accordingly this difference in behavior shows that the "plasticity" of a metal depends upon the mode of action of the stresses which produce the deformation, and therefore upon the method of test. Analysis of the stresses leads to the conclusion that the observed plasticity of a metal is determined by the relation between its resistance to rupture by separation and its resistance to shear (slip), on the one hand, and between the effective normal and shearing stresses on the other; and that the relation between the two resistances does not in general remain constant with change of temperature, and may somehow be altered to some extent by the previous treatment of the specimen. This suggests the view that the results of none of the usual mechanical tests are directly comparable even for a single metal tested at a series of temperatures, or for a series of metals at one temperature, because the proportion of the total resistance of the metal to the test contributed by the

Jan 1, 1935

By K. Heindlhofer

Estimates of the "plasticity" of a metal are commonly deduced from three types of test—tensile, torsion and impact. The several results have been more or less at variance, though this disparity has attracted little notice, largely perhaps because they have been expressed in different terms. The discrepancy between the results of the three tests becomes obvious when each is made at a series of low temperatures, for the temperature range within which the "plasticity" of iron largely disappears proves to be very different in the three types of test. The rather abrupt disappearance of "plasticity" of iron within a narrow temperature range cannot be due to any physicochemical change (such as a precipitation) taking place in the material at that time, because the original plasticity is immediately regained when the temperature of the material is brought above the sensitive range. Accordingly this difference in behavior shows that the "plasticity" of a metal depends upon the mode of action of the stresses which produce the deformation, and therefore upon the method of test. Analysis of the stresses leads to the conclusion that the observed plasticity of a metal is determined by the relation between its resistance to rupture by separation and its resistance to shear (slip), on the one hand, and between the effective normal and shearing stresses on the other; and that the relation between the two resistances does not in general remain constant with change of temperature, and may somehow be altered to some extent by the previous treatment of the specimen. This suggests the view that the results of none of the usual mechanical tests are directly comparable even for a single metal tested at a series of temperatures, or for a series of metals at one temperature, because the proportion of the total resistance of the metal to the test contributed by the

Jan 1, 1935

Texture Transition in Ordered CuAu, by E. A. Starke, Jr., J. C. Ogle, and C. J. Sparks, Jr., Trans. TMS-AIME, 1969, vol. 245, pp. 169-70. pole figures should have had two parts not one. On the Estimation of Oxygen Absorption by Continuous Molten Metal Streams, by J. Szekely, Trans. TMS-AIME, 1969, vol. 245, pp. 341-44.

Jan 1, 1970

Jan 1, 1967

By L. K. Jetter, J. C. Ogle, C. L. McHargue

The preferred orientation developed in extruded aluminum rods has been studied as a function of extrusion temperature, extrusion speed, and position in the rod. Duplex <111> - <001> textures were developed for slow extrusion speeds at temperatures of 75° to 850° F and for fast extrusion speeds at temperatures of 75° to 450°F. The <001> texture component was shown to be primarily due to re crystallization occurring during fabrication. At fast speeds and billet temperatures of 650° to 850°F, complete recrystallization occurred and <115>or<118> textures were found. The nature of the structure has proved to be an important variable in the production and use of extruded products. Data on the flow of aluminum and aluminum alloys summarized by Smith,&apos; Hardy,&apos; and Locke3 show that the extruded product may possess a deformed, a partially recrystallized, or a completely recrystallized structure, and there may be important variations in the structure from surface to center and from front end to back end of an extrusion. This inhomogeneity in grain structure and preferred orientation affects both the mechanical properties of the extruded section and its response to subsequent heat treatment. Among the fabrication variables causing these differences are temperature, extrusion ratio, and extrusion speed. Preferred orientation which develops during the extrusion of rods is of the fiber-type and, in general, has been assumed to be similar to that developed in rods or wires fabricated by drawing through dies, rolling, or swaging.4 Because of the nature of the flow of metal being extruded, this assumption may be valid for material near the center of the rod but probably is not valid for the outer layers. In most face-centered-cubic metals a duplex fiber texture has commonly been reported in which the grains have either <Ill> or <001> directions parallel to the longitudinal axis. Sachs and fichiebold5 reported cold-drawn aluminum (99.6 pct pure) to have a single <Ill> fiber texture, and this observation was confirmed by Schmid and Wassermann.6 Hibbard, on the other hand, observed a minor <001> and a major <111> texture in 99.994 pct A1 cold drawn to 98 pct reduction in diam.7 He concluded that the <001> component resulted from a small amount of room-temperature recrystallization. Dayal8 concluded that the <001> component was an intermediate component which disappeared at high reductions in 99.5 pct pure Al. Kostron and schippers9 found duplex <111> — <001> textures in extruded 99.5 pct Al, as did Gow and cahnl0 and GOW11 for extruded rods of commercial and superpure aluminum. Similar duplex fiber textures have been reported for aluminum alloys by Kostron,= Unckel,13 and Van Horn.14 The present paper is concerned with the variation in texture with fabricating conditions and with the nature of the texture components in extruded aluminum rod (99.99 pct pure). EXPERIMENTAL PROCEDURE Ingots were chill-cast in cast-iron molds and machined to 3-in. diam by 6-in. long extrusion billets. These billets were upset to 3.125 in. diam and extruded through a flat-face 0.690-in. diam die. Quenching of the rods was accomplished by a water spray at the die face. The combinations of fabricat-

Jan 1, 1960

By W. J. Rude

LARGEST of the known commercial deposits of pebble phosphate are those found in Polk County, Florida. The phosphate bed, commonly known as the matrix, will consistently average 6 to 9 ft. in depth, and is found under 3 to 60 ft. of over-burden. The phosphate pebbles, white and black in color, varying greatly in grade, are found imbedded in a matrix of sand and clay; and range in size from the fines to pebbles 1 1/2 in. in diameter, although the average coarse size is approximately 1/2 in. in diam¬eter. On some of the washers all material under 14 mesh is lost. High-grade phosphate (75 per cent plus of bone phosphate of lime, CasP2Oa) is generally soft, the pebbles breaking up during the mining operation and in pumping; low-grade phosphate, 67 to 69 B.P.L., is black in color with hard pebbles with no loss encountered in pumping.

Jan 1, 1941

By J. E. Campbell, G. D. Calkins, N. M. Ewbank, M. Pobereskin, A. Wesner

GRINDING for size reduction affects the economics of many processes and products. It is essential as the first step in many industrial processes and is also a finishing step for materials with properties depending on particle size, such as talc, cement, and silica sand. Intermediate and fine grinding are vital operations in the U. S. cement industry, which is producing more than 250 million bbl of cement per year.1 Wear of the grinding media is a large part of the grinding operation cost. Problems encountered in grinding cement are so complex that evaluation of efficiency and economy of grinding media is difficult.2 It has been especially difficult to evaluate the relative effectiveness of different types of balls because there are no good testing techniques.

Jan 12, 1957

Jan 1, 1955

By K. Mukherjee

Instantaneous resistance change during martensitic transformation in Fe-30 at. pct Ni alloy has been studied using a low-noise electronic system. The smallest signals recorded in this investigation were of the order of 10 pv. These small signals did not show the initial increase reported by earlier investigators to support a double shear mechanism.&apos; A variety of pulse shapes and sizes was observed during "burst" transformations, and these signals were neither a linear function of the size of martensite plates nor of the volume fraction transformed. Even the smallest signals, presumably from single plates, showed complications resulting from elastic and/or plastic deformation, shock wave propagation, and so forth, which are inherent in the growth process of a martensite plate. The time of formation and interface velocity determined froni this experiment agree very well with the pioneering work of Bunshalz and Mehl.&apos; AN Fe-30 at. pct Ni (c0.005 pct C) alloy was used to study the time of formation of martensite plates. Martensitic transformations, unlike the nucleation and growth processes, are usually characterized by an extremely fast reaction rate. During the transformation, the crystal structure changes and this change is propagated through a finite volume of the parent crystal lattice within a very short time interval. The interface between the two phases probably consists of moving dislocations, and the time of formation of the plate depends on how fast this dislocation interface can move. Knapp and Dehlin~er or Cottrell and Bilby mechanisms, or similar dislocation models, can be used to calculate the time of formation of a martensite plate of a given size. In the past, conventional photographic technique475 as well as electrical resistivity techniques"~-" have been used to measure the time of formation of a martensite plate. The specific resistance of the martensitic phase in Fe-30 at. pct Ni alloy is lower than that of the austenite phase. Therefore if a current is passed through a small austenite sample in series with a large external resistance, then one would observe a voltage change across the sample as martensite is formed. Such dc measurements are shown in Fig. 1. The initial large voltage drop in Fig. 1, at the M, temperature, is due to a "burst" transformation where a large number of plates are formed in a cataclysmic manner within a very short interval of time. Even during the later stages of transformation as shown in Fig. 1, one can observe discontinuous voltage changes due to small bursts. In order to resolve the time scale of such discontinuous stages, the voltage signals are amplified and fed into a highspeed oscilloscope. In this investigation a low-noise amplifier was used for the first stage of amplification. The signal to noise ratio was further improved by the design of a pulse transformer. This transformer was capable of amplifying the signal by a factor of six. Voltage signals were studied over a wide time scale ranging from 2 sec to 0.1 psec. I) EXPERIMENTAL PROCEDURE A) Specimen Preparation. Specimens were cut from induction-melted Fe-30 at. pct Ni (<0.005C) alloy and cold-rolled to 0.2 by 1 mm cross section and an average length of 5 cm. During mechanical shaping, the specimens were strain-annealed at 950°C for 24 hr in vacuum. Finally the finished samples were vacuum-annealed at 1000°C for 6 hr and water-quenched to room temperature. The average grain diameter was 0.02 cm. B) Cooling System. The M, temperature of the alloy was -55°C. Fig. 2 shows the arrangement which was used to cool the specimen at a slow rate. The specimens were mounted inside a i -in.-diam hole in the 2-in.-long section of the copper specimen holder. This cavity was filled with silica gel. A dummy specimen was used under identical conditions for

Jan 1, 1969

By W. H. Bassett

THE ease and value of the application of spectrum analysis to industrial chemistry appears to be appreciated in few of the large works laboratories of this country. For 8 years, this analysis has been of great value to the authors in both analytical and metallurgical work. To the analyst the complete qualitative analysis of an unknown alloy, revealed by a spectrogram, is a sure basis for the planning of the most direct and rapid method of attack. As the determination of each element proceeds, the purity of precipitates may be checked as often as desired. The spectrograph proves invaluable in the recognition of impurities, the separation of which would entail a lengthy and difficult procedure, or when the weight of an unknown is less than is necessary to complete the desired determinations. A few hundredths of a gram will usually suffice for spectrographic analysis. In the separation of the rarer elements, the spectrograph will show, with precision, the point where each step has been successful. In zinc of certain classes, indium, gallium, and germanium have been isolated in this way; the presence of antimony in lake coppers has been proved; and bismuth has been detected in zinc and in alloys where the presence of a few thousandths of a per cent. would be harmful. An antimony precipitate in a delicate determination may contain a considerable proportion of tin or arsenic, both of which will be revealed. The spectrograph is consequently important to the metallurgist as well as to the analyst.

Jan 2, 1922

By J. F. Enrietto

Internal friction measurements were used to determine the effect of manganese on the solubility and precipitation kinetics of nitrogen. Manganese, in concentrations up to 0.75 pct, has little effect on the solubility at temperatures above 250°C. On the other hand, at Concentrations as low as 0.15 pct, manganese inhibits the formation of iron nitrides, especially Fe4N, even though it may not form a precipitnte itself. The precipitation and solubility of carbides and nitrides have been extensively investigated in the pure Fe-C and Fe-N systems.1-3 In recent years, some effort has been ispent in studying the influence of substitutional alloying elements on the behavior of carbon and nitrogen in ferrite.4 -7 In particular Fast, Dijkstra, and Sladek have investigated the effect of 0.5 pct Mn on the internal friction and hardness during the quench aging of Fe-Mn-N alloys.&apos;, &apos; They found that at low temperatures (below 200°C) the presence of 0.5 pct Mn greatly retarded quench aging. For example, after 66 hr at 200°C very little precipitation had taken place in the iron alloyed with manganese, whereas precipitation was complete after a few minutes in a pure Fe-N alloy. The effect of varying the manganese content and the details of the precipitation process were not mentioned in these papers. Fast&apos; postulated that manganese causes a local lowering of the free energy of the lattice with a resulting segregation of nitrogen atoms to these low energy sites. The segregated nitrogen atoms are bound so tightly to the manganese atoms that they cannot form a precipitate. The internal friction measurements of Dijkstra and Sladek tended to confirm the concept of segregation of nitrogen around manganese atoms, and the increase in free energy on transferring a mole of nitrogen atoms from a segregated to a "normal" lattice site was computed to be - 2800 cal. Dijkstra and Sladek9 distinguished between two types of precipitates: ortho, a nitride of appreciably different manganese content than that of the matrix, and para, a nitride with a manganese content essentially that of the matrix. With each type of precipitate a solubility, again designated ortho or para, can be associated. Since the internal friction maximum in alloys which were aged several hours at 600" C dropped almost to zero, Dijkstra and Sladek9 concluded that the ortho solubility must be very low. The effect of temperature on the ortho and para solubilities has no1: been investigated. There are obviously several gaps in our knowledge concerning the influence of manganese on the behavior of nitrogen in a-iron. It was the purpose of the experiments described in this paper to determine the following: 1) The ortho and para solubilities of nitrogen as a function of temperature. 2) The details of the precipitation process at elevated temperatures. 3) The effect of varying the manganese concentration on the above phenomena. EXPERIMENTAL PROCEDURE Internal friction is conveniently employed in studying the precipitation of nitrides and/or carbides from a -iron because it is one of the few parameters, perhaps the only one, which is not affected by the presence of the precipitate itself. For this reason, internal friction techniques were heavily relied upon in the present experiment. A) Preparat of -. All specimens were prepared from electrolytic iron and electrolytic manganese. Alloys containing 0.15, 0.33, 0.65, and 0.75 wt pct Mn were vacuum melted and cast into 25 lb ingots. After being hot rolled to 3/4 in. bars, the ingots were swaged and drawn to 0.030 in. wires. The wires wen? decarburized and denitrided by annealing at 750° C for 17 hr in flowing hydrogen saturated with warer vapor. To obtain a medium grain size, - 0.1 mm, the wires were then heated to 945oC, allowed to soak for 1 hr, furnace cooled to 750°C, and water quenched. Subsequent internal friction measurements showed that this procedure reduced the nitrogen and carbon concentrations of the alloys to less than 0.001 wt pct. The wires were nitrided by sealing them in pyrex capsules containing anhydrous ammonia and annealing them for 24 hr at 580°C, the nitrogen being retained in solid solution by quenching the capsule into water. Immediately after quenching, the wires were stored in liquid nitrogen to prevent any precipitation of nitrides. By varying the pressure of ammonia in the capsule, it was possible to produce any desired nitrogen concentration. B) Internal Friction. The internal Friction measurements were made on a torsional pendulum of the Ke type,&apos;&apos; a frequency OF 1. or 2 cps being used. For

Jan 1, 1962

By E. P. Palmatier

RECENTLY a cooling system has been in process of installation on the 3400 and 3600-ft. levels of the Magma copper mine at Superior, Ariz. The general system of ventilation employed at this inclined-vein mine is as follows: Ventilating air enters the shafts on the western side of the mine. Booster fans at each level each deliver approximately 38,000 cu. ft. per &apos;min. to the drifts. This air passes diagonally upward to the upper levels of the mine on the eastern side, where it passes up the shafts to large exhaust fans on the surface. Owing to the dip of the vein, all operations on the eastern side of the mine are above the 2500-ft. level, and those on the western side below the 2500-ft. level. At present, 2500 lineal feet of new drifts are being driven-on each of the 3400 and 3600 levels. The rock temperature is about 135°F. Until the new installation is completed, ventilating air for the two levels is supplied through Flexoid tubing from small booster fans -on the 3200-ft. level. The air picked up by these booster fans has a dry-bulb temperature of approximately 85°F. and a wet-bulb temperature of 82°F. By the time this air reaches the end of the Flexoid tubing at the 3600-ft. level, the dry-bulb rises to 101°F. and the wet-bulb to 86°F. The conditions at the head of the new drift were 102&apos; dry-bulb and 93&apos; wet-bulb.

Jan 1, 1937

By R. M. Kuralt

CONCESSION from the Chilean government granting the company use of the Rio Salado water stipulates that a minimum of 35,000 metric tons of such salty water must be diverted from the Salado daily, and be disposed of in a manner not to contaminate the Rio Loa to the east of its confluence with the Rio San Salvador at Chacance, Fig. 1. Consequently, the selection of a suitable site for the sulphide plant tailing disposal had the additional problem of the disposal of excess brackish waters. Studies of the terrain in the area directly to the south of the plant indicated that construction of tailing ponds would be costly, and generally unsatisfactory due to excessive slope of the ground, lack of flanking hills, danger of raising the groundwater level thus causing springs along the Antofagasta-Bolivia railroad; and the possibility of creating a dust nuisance at the plant site or at Calama due to blowing sands. Further to the southwest the San Salvador river canyon offered some possibilities and surveys were made at sites A to D, inclusive, Fig. 1. Here again costly dams would have been necessary to impound the tremendous quantity of tailing produced by the new plant, and provision would have to be made to handle a considerable flow of water through the disposal area to the west of the Rio Opache. Additional surveys were made in the area to the southeast of the plant which brought to light the existence of a natural basin of about 14 1/2 square miles, flanked by low-lying hills, and requiring only the most rudimentary dams to close the outlets at the western end. It has been estimated that the Salar de Talabre, as this basin is called, has the ultimate storage capacity of 1 billion tons of tailing with dam heights of only 60 ft. Pipe Line Layout After the decision had been reached to use the Salar de Talabre for the main disposal area various methods were considered for transporting the tailing from the 300 ft diam thickeners to the disposal site, 17.7 miles away. The first plan was to construct a. concrete launder on a 11 pct grade but a survey of this grade line indicated it would not lead directly into the Salar but would terminate somewhat to the north, and from that point on the slope would be considerably less than 1 pct along a natural watercourse. A slope of 2 pct or even 2 ¼ pct in such a rough watercourse or ditch is the ideal, judging from the success of operations at Cananea. Since a simple ditch is the most economical vehicle for the transportation of tailing, it was decided to use one with a 2 ¼ pct grade for as much of the distance as was possible with the existing terrain and to construct a concrete headbox, or forebay, at the terminus of the ditch to supply a steel pipe line leading the rest of the way into the Salar. Referring to the maps of the Chuquicamata area outlining the tailing disposal system, Figs. 1 and 2, one can trace the flow of the tailing from the thickeners to the Salar as follows: The 8-in. spigot pipes from the thickeners (1) discharge into a concrete sump feeding a concrete launder with a 2 pct slope. The launder carries the tailing into a concrete junction box (2) located south of the sulphide plant. The purpose of the junction box is to provide emergency facilities for diverting the tailing flow from the main disposal area to the emergency area. It also provides a junction point for the launder from the sulphide plant&apos;s future east extension. The box is fitted with a pair of radial gates controlling flow into the main tailing ditch (6) or the emergency ditch (3) which terminates on the pampa. All ditches are of the same cross section, namely 4 ft wide at the bottom with 1 : 1 side slopes and with a minimum depth of 21/2 ft. Where the nature of the ground demands it, the ditches are lined with stone rubble. The overflow from the plant&apos;s 10 million gal reservoir (4) is led into the main tailing ditch by way of a spillway ditch (5). The main ditch terminates in a trashscreen fitted, concrete forebay (7) which serves as a headbox for a 24 in. O.D. x 3/8 in. wall, Dresser coupled, steel pipe (10) and a 12 in. x 8-gage spiral welded, wedge-lock coupled, steel pipe (8). The forebay is fitted with two compartments, one for each pipe, and flow into each is controlled by radial gates. Each compartment is fitted with a 6-in. drain pipe controlled by a rubber pinch valve. To protect the forebay from the abrasive effects of the tailing, the sides of the compartments will be lined with old

Jan 1, 1952