Search Documents

By E. S. Machlin, W. R. Yankee

IN a previous study1 of the effect of heating com-mercial titanium in air on its subsequent friction coefficient against other metals, as well as itself, it was found that the friction coefficient markedly decreased from a value of about 0.7 to about 0.3. A tentative explanation was given that surfaces normally produced at room temperature are not contaminated sufficiently to prevent seizing or welding of the titanium to the softer mating metals. The latter tend to cleanse themselves during rubbing over the harder titanium. It was thought that the lack of a contaminant protective film on the titanium was due to the high solubility of titanium for oxygen and nitrogen and hence an inability to form a contaminant oxide or nitride. This explanation requires the ratio of the surface absorption rate to the diffusion rate to become much lower at room temperature than it is at high temperatures. In order to check the phenomenon further, commercial titanium specimens were nitrided or oxidized at 800°C for 20 hr in flows of prepurified N2 and 01, respectively, at about 1/2 in. H2O above atmospheric pressure. Friction runs were made in argon using a freshly cut copper hemisphere (cut in argon) on surfaces cut successively into the diffusion layers in the titanium (cut in argon) using the techniques described in a previous publication.' DPH values (100 gram load) were made as a function of depth into the diffusion layer using a Tukon tester. Also, micrographs were taken at separate cross sections to indicate the diffusion layers. The results obtained are presented in Figs. 1 and 2, which show the "static" friction coefficient vs hardness for the nitrided and oxidized specimens, respectively. A separate measurement of the friction coefficient of clean copper vs iodide titanium also was made. From results reported in the literature' giving the oxygen and nitrogen contents as functions of the hardness, cross plots were made showing the friction coefficients as functions of the amount of interstitial solute. These plots are given in Figs. 3 and 4. From micrographs of the diffusion layers and the phase diagrams, it was deduced that the data in Figs. l through 4 correspond to the single phase a region. The points observed on the compound regions have been excluded from the figures. It is apparent that nitrogen or oxygen in solution in the a titanium markedly affects the friction coefficient against a softer mating metal. Discussion of Results These results are extremely interesting from both a practical and theoretical viewpoint. The theoretical implications will be discussed first. According to Bowden, the friction coefficient should be given to a good approximation by the relation where a is the fraction of contact area that has welded, a is the shear strength of weaker component, and H is the hardness of softer component. Using this relation alone, it is difficult to understand the results because none of the terms should be affected by a variation in the oxygen or nitrogen content of the harder and stronger metal, titanium. Even if the ratio of S/H for titanium is used in Eq. 1, the ratio has been shown to be independent of oxy-gen or nitrogen content.' If a more rigorous equa-tion is used combining Eq. 1 and a result given pre-viously" for the case where welding is absent, then the relation obtained is µ = a S/H + (1-a) a W aß/H where a is constant and Waß is the work of adhesion between the two metals comprising the friction couple. This relation states that if a is less than 1/2 or so, variation in the work of adhesion Waß between copper and the titanium should affect the friction coefficient markedly. It is reasonable to expect that the work of adhesion will depend on the oxygen or nitrogen content of the titanium. Available data4 show that clean metals and oxides have much lower works of adhesion than the same metals against the

Jan 1, 1955

By T. Egleston

THERE has always been a-theory among those working placer mines that gold is both found " rusty," and becomes so under treatment, by which they mean, not that gold becomes coated with oxide of gold, bat that it is either coated superficially or alloyed with sortie substanee 'which prevents the ,contact with mercury, and thus precludes the possibility of amalgamation. To such conditions of the

Jan 1, 1881

By S. S. Arentz

An organized safety program has reduced accidents at Pioche because effort is first devoted to arousing and maintaining interest in safety, followed by training in accident prevention, assigning responsibility for the detection and removal of safety hazards, and finally, by keeping score through an adequate system of records. A health program is intergrated with the safety program.

Jan 1, 1950

By James K. Grunig

As the real price of uranium increases, deposits of lower and lower grade will be treated. The various occurrences of uranium ore are described and the chemical aspects of extraction are detailed.

Jan 1, 1981

By AIME AIME

THE Fall Meetings of the Institute of Metals Division and of the Iron and Steel Division were held in Cleveland from Tuesday, Oct. 20, to Thursday, Oct. 22, as a part of the National Metal Congress. The registration at the technical sessions was something over 450 and the attendance at the joint dinner of the two Divisions on Wednesday evening taxed the capacity of the dining room. The president of the British Institute of Metals, W. R. Barclay, consulting metallurgist to the Mond Nickel Co., Ltd.; of London, was in attendance at several of the technical sessions and was one of the after-dinner speakers at the banquet. He commented on the desirability of greater international amity and cooperation in these troubled times and of the role that technical societies, such as the A. I. M. E. and his own British Institute of Metals, can and indeed are playing in bringing this to pass, with their membership and contacts reaching to all parts of the world. He also referred to the new reciprocal membership arrangements in effect between the A.I.M.E. and the British Institute of Metals.

Jan 1, 1936

By Charles Bohdanowicz

As in preceding years, the most intensive drilling activity during 1934 took place in the old fields of the western part of the Polish Carpathian petroleum province (district of Jaslo). The number of wells completed to the end of 1934, expressed in percentages, is as follows: Jaslo district, 57 per cent; oil fields outside Boryslaw-Tustanowice-Mraznica, 27; Stanislawow district 8 and Boryslaw fields only 7 per cent. The number of meters drilled (Table 2), expressed in percentages, for the same fields are as follows: Jaslo district, 51 per cent; oil fields outside Boryslaw-Tustanowice-Mraznica, 26; Stanislawow district, 12, and Boryslaw oil fields, 11 per cent. This comparison shows that most of the new

Jan 1, 1935

By William H. Shockley

[SECRETARY'S ]NOTE.-The following notes, arranged and edited in this office, but not yet revised by the author, were placed at my disposal with much modest hesitation (due to their incomplete and fragmentary character), upon my earnest request, and my argument that such recent and trustworthy data concerning a new and important mining industry ought not to be withheld from our Transactions, simply because they are not sufficient to constitute a, complete academic treatise on the subject. This argument is recommended to the attention of many other members, who are waiting for the opportunity to contribute something "monumental" to our Transactions. In a number of instances, death has nulli¬fied this ambition, and the intended "monumental" contribution has turned out to be an obituary notice by the Secretary, instead of a valuable record of the professional experience thus hopelessly lost to the world.-R. W. R.] The official publications of the the Russian Government give fairly complete statistics of the dredges operated in the Empire; and in a recent English bluebook, Mr. Cook's report on Siberian Trade presents a brief account of dredging in Siberia. The data in Table I. (not given by Mr. Cook) have been taken from the Gold Mining Messenger (Russian) for July, 1905. These interesting statistics, though incomplete, show that the Yenisei dredges are working on poor ground and yield small returns. According to report, but few yield a profit exceeding 10 per cent. per annum on the capital invested. In the summers of 1904 and 1905, I traveled in the Urals as far north as lat. 61° N., long. 61° E., on the the Lozva river, a part of the vast system of the 01) river. This clear-water stream starts from the summits of the Urals at an altitude of 4,000 ft., and flows through a flat country, densely wooded with larch, spruce, pine, fir, birch and poplar. The river is full of fish, and is navigable for good-sized steamers as far as Ivdell. Winter lasts from early November to late April, the temperature rang¬ing from -60° F. to a summer maximum of 90° F. The rain¬fall is 20 in.. The climate is healthy, although mosquitoes,

Jul 1, 1906

Jan 1, 1969

By William F. Boericke

CONSIDERABLE waste of oil and grease in lubricating motors and other machinery results from the use of bearings that are not totally enclosed. There is also the likelihood of damage to the bearing through the accidental introduction of grit or dust both in the oiling process and after, unless the cover is entirely dustproof. With the ordinary sleeve bearing that is only partly enclosed, it is generally easier for a careless attendant to cause trouble through neglect than with the ball bearing type, which from its design, must be totally enclosed to give effective service, and needs a minimum of attention. At one of the large mining companies which has taken a leading part in reducing unit costs and pioneering new developments in mining machinery, ball bearings have been gradually supplanting the conventional type of sleeve bearings on many of their motors, centrifugal pumps, and other machines in the mines. This innovation is not recent, as substitution of ball bearings on mine motors was first tried out by this company in 1909. Since then an increasing number of such bearings have been put in. They are now favored because of increased operating efficiency and reduction in lubrication costs.

Jan 1, 1926

By W. B. Plank

I HAVE been asked by the Chairman of the Engineering Education Committee to outline what the engineering colleges would like the mining companies to do with the young engineer just, out of college. It has been suggested that, because my own personal experience has been almost entirely within the coal industry, I handle this subject from that view- point. Many thoughtful engineering educators are today wondering what effect the present employment policies of many industrial companies are going to have on the young man just starting out in his profession. Since before the World War large industrial concerns, such as those in the electrical and mechanical industries, have gone to the colleges to interview 'likely graduates until today there has developed in most of our engineering colleges, especially in the eastern part of the country, what appears to be a lively competition on the part of these companies in bidding for the young graduate engineer. The employers of mining engineers, with one or two exceptions, have not yet begun to enter this competition. It remains to be seen how serious this situation will become, how it will affect the training of other engineers, and what effect, if any, it will have on the mind of the young man about to enter college who may be inclined to take up mining engineering, but who gains the impression from this well advertised employment service just mentioned that there is no opportunity for him in the mineral industry as com- pared with the opportunities offered in say civil, mechanical, and electrical engineering.

Jan 1, 1929

By E. J. Roberts

Prior to 1916, thickening was an art, and any accurate decision as to what size of machine to install to handle a given tonnage of a specific ore must have been one of those intuitive conclusions, based on both intimate and extensive acquaintance with thickners and ore pulps. Then in 1916 "knowledge of acquaintance," became "knowledge about" with the publication of the Coe and Clevenger paper.' The unit operation of thickening had graduated to the status of an engineering science. The fundamental similitude relationships for the two major phases of the operation were defined so clearly that batch tests on models as small as liter cylinders could serve to specify protypes as large as 325 ft in diameter.

Jan 1, 1949

By Pei-Yung Huang, Carle R. Hayward

IN order to understand more fully the actual state of copper lost in copper reverberatory slags, a systematic study on the various reactions between certain metallurgically important copper compounds and synthetic copper reverberatory slags was undertaken by the authors in the Massachusetts Institute of Technology from 1942 to 1945.1 This paper, being only a part of the work completed, is published first because it furnishes the first experimental evidence of the formation of copper ferrite from reactions between cuprous oxide and copper reverberatory slags. CHOICE OF SLAG COMPOSITION The choice of the composition of the synthetic reverberatory slags to be used was much deliberated. Commercial copper reverberatory slags, neglecting minor constituents, average:2.3 45 to 47 pct FeO; 38 to 42 pct Si02; 5 to 6 pct CaO; 5 to 6 pct A1203. Since the ternary system CaO-FeO-SiO2 has been much more thoroughly studied4 and is much simpler than the quaternary system CaO-FeO-Si02-A1203, it was decided to use calcium oxide only instead of calcium oxide and alumina in the synthesis of the slags. Fortunately the composition of the average copper reverberatory slag with calcium oxide substituted for alumina lies in the region of the phase diagram clarified by the investigators. A survey of the phase diagram (Fig I) suggested two compositions: (I) the com¬position near the invariant point S, which is made up of 46 pct ferrous oxide, 37 pct silica and 17 pct calcium oxide; (2) the composition near the invariant point K with 45.5 pct ferrous oxide, 43 pct silica and 11.5 pct calcium oxide. Composition S has the advantage that the percentages of ferrous oxide and of silica almost exactly coincide with those of the average reverberatory slags, and that of the lowest melting point (1093° ± 3°C) in the whole ternary system. The calcium oxide content, however, obviously is high. Since we have already substituted calcium oxide for alumina, and since calcium oxide is more basic than alumina, the resulting slag is decidedly too basic. Composition K has a slightly higher melting point (1105° ± 3°C) and a higher silica content, but this is preferred because the slag is saturated with respect to tridymite and thus should not corrode siliceous refractories. Besides, it is less basic than composition S. The final slag composition, therefore, was chosen to

Jan 1, 1947

By Thomas T. Read

EVERYONE engaged in the teaching of mining engineering will, I suppose, agree that the most difficult subject to teach is "Mining Methods." One primary difficulty is that the students taking the course have either had no previous experience in mining, or else they have had; either seeming to be somewhat of a drawback. The students who are unfamiliar with mines find it difficult to visualize underground conditions, as described and illustrated with sketches and maps, while those who have had underground experience seem to 'find it difficult to visualize anything much different from that which they have already seen. This reminds one of the remark about the Presbyterian doctrine of predestination, to the effect that "you are damned ,if you do; and damned if you don't."

Jan 1, 1930

By H. OSBORG

THE patent literature of alloys for the last two decades or so indicates that the number of liatents referring to smaller and smaller percentages of essential alloying constituents is on the increase, whereas the number of patents relating to considerable percentages of alloying additions becomes smaller. The claims regarding physical properties indicate consistently higher and more rigid values and show the possibility of modifying the physical properties by only slight changes in the percentage of minor constituents or by applying different methods - of treatment. Alloys of the same base have been made suitable for a number of different applications by intelligently and rigid- ly controlling their composition, melting, casting, working, and heat-treatments. Other trends indicated in the development of modern alloys are higher corrosion resistance, higher fatigue limits, and "stability" in volume.

Jan 1, 1937

By S. Frederick Ravitz

JUDGING from the inquiries that are constantly being received by the Utah Engineering Experiment Station as to the "Why," so to speak, of the flotation process of concentrating minerals, it occurred to me that perhaps a brief statement of the more important theories might interest those who have not followed the technical literature. Like many other industrial processes, flotation has hitherto been developed on an almost purely empirical basis, with relatively little practical contribution from the fundamental chemistry and physics on which the phenomena are based. In fact, its development by the trial - and - error method has been perfected to such a high state that it is becoming generally thought that further important advances can be brought about only by a thorough understanding of the actual mechanism of the process. Natur¬ally, such a complicated process has brought forth numerous theories, most of which have failed to withstand the test of time. It is significant that no theory has yet been advanced which is universally accepted.

Jan 1, 1933

By Frances Jane Cromwell, D. J. McAdam, G. W. Geil

In a series of papers, the authors and their associates have shown that the technical cohesion limit is affected by the same four factors that affect the flow stress, namely, the stress system, plastic deformation, temperature, and the strain rate.16-28 Moreover, each of these factors affects the technical cohesion limit in the same way that it affects the flow stress,t The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term ilfracture stress' has come into use with the same significance as 'ctechnical cohesion limit," the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. This paper presents the results of an investigation of the flow of notched and unnotched specimens betqrcen yield and fracture, A study has thus been made of the flow and fracture of metals as affected by the stress system, and of the ductility of metals as affected by the stress system throughout plastic deformation. Since two of the principal stresses were equal (S2 = S3), the stress systems can be represented in terms of the radial stress ratio, the ratio of the transverse radial stress s3 to the longitudinal stress S1.* The results of the experiments are represented by a series of their flow-stress curves for each Of the metals investigated, and these diagrams have been used for the development Of Other diagrams Of various types. Ludwik was the first to suggest that fracture occurs when the flow stress becomes equal to a technical cohesion limit. Although Ludwik was incorrect in his view that the technical cohesion limit depends only on the amount of plastic deformation and not On the stress system, he was 'Orrect in his view that the flow-stress curve for any stress system terminates at a point representing a technical cohesion limit. The authors have seen some recent references to assertions by other investigators that a point representing the fracture stress need not be on the flow-stress curve. The Ludwik principle, however, "auld Seem to be axiomatic, provided that the flow Stress and fracture stress are properly defined and that the fracture stress is properly determined. Disregard Of this principle has led to some untenable theories Of criteria for fracture. When a metal is very ductile, the conventional method of determining the ductility and fracture stress by dividing the breaking load by the sectional area after fracture, generally gives values that are much too high. With some metals and in some conditions, the fracture stress thus determined may be two or more times the

Jan 1, 1949

The Board of Directors, at its meeting on March 22, 1918, extended an invitation to the American .Institute of Metals to become the Institute of Metals Division of-the American Institute of Mining Engineers in accordance with the terms of By-Law VII. This invitation was presented to the membership of the American Institute of Metals for letter ballot, and, at the meeting of the Board of Directors of the American Institute of Mining Engineers on April 26 191 ,it-was reported that the replies had been in favor of accepting the invitation. The American Institute of Metals therefore becomes a division of this Institute and the members thereof are entitled-to all privileges of regular

Jan 6, 1918

By AIME AIME

STRIP coal mining in the United States has-become noted for its massive equipment, especially its power shovels. Notable among the latest examples of this trend is the Bobolink mine of the Binkley Mining Co., at Seeleyville, Ind.,. eight miles from Terre Haute. This is only one of the Binkley company's operating properties; in all, the company owns or controls 26 mines, in fourteen seams. The Bobolink, however, is the largest strip mine in America and probably also in the world. It has an estimated life of fifteen years. The shovel used to strip the over¬burden is electrically operated, of Bucyrus-Erie make, and was. shipped to the property for assembling, a job

Jan 1, 1936

By V. D. Leary, O&apos

Contracts between The Anaconda Co. and its miners at Butte, Mont., are not contracts in the true sense of the word. They are weekly verbal agreements which tacitly admit that the company, on the one hand, will supply the place, the tools, the material, and the opportunity and that the miners, on the other hand, will supply such effective labor that both parties will profit from the arrangement. Prices are seldom discussed at the time of hiring. The miner, in effect, is hired for a definite working place, as a contract miner, and if satisfied, tries to earn as much as he can. If he is not satisfied three courses are open to him: he can quit, he can ask for a change, or he can discuss prices or improved working conditions with the mine superintendent. This rather informal arrangement is due to conditions that are particular to Butte

Jan 2, 1961

By Howland Bancroft

AMERICAN investment in foreign mining interests today faces its greatest task. U. S. dollars must make possible the. steady procurement of the minerals our defense effort consumes in huge quantities. The two most vital factors involved in foreign procurement are time and the continued good will of the nations from which minerals are purchased. The Point IV program was formulated to care for the second item, but it has failed to do the job. Its lack of success has not been from intent or from basic failure in formula. Foreign Investment, Four Eras Foreign mineral development, in so far as participation by private capital from the United States is concerned, may be divided into four main chronological categories: First: The period prior to the first World War when people, capital and products moved with relative freedom across international boundaries, and London was the recognized mining seat of the world. By the end of 1919 the United States direct investments abroad amounted to $3.9 billion of which some $900 million were in mining and smelting and $600 million in petroleum. Investment climate throughout most of the world was excellent. Second: The period between the end of World War I, when the international economy had been shaken from its foundations, and the beginning of the great depression of the 1930's, which still further disrupted the world economy. By that time the world mining center had moved across the sea and the United States direct investments abroad had increased to $7.7 billion of which mining and smelting accounted for $1.2 billion and petroleum for $1.1 billion. Investment climate was good in most parts of the world. Third: The period of the depression of the 1930's and the beginning of World War II during which foreign trade was still further disorganized and the international economy collapsed. Nazi barter agreements were initiated in many parts of the world, and Soviet propaganda commenced to make its, influence felt in many countries. During this period United States direct investments abroad decreased to $7.3 billion. Mining and smelting investments during the same period decreased some $200 million, though direct investments in foreign petroleum areas increased an equal amount. Investment climate became less and less hospitable in all parts of the world affected by economic nationalism. Fourth: The period since the beginning of World War II during which total direct investments abroad increased from $7.3 to $13.7 billion. Of this sum, at the beginning of 1950 investment in foreign mining and smelting is reported to have been $1.2 billion-back to where it was in 1929, and in petroleum to have reached $3.7 billion. Investment climate remained favorable in the countries respecting contractual obligations and fair in their treatment of invested capital. [ ] As noted above, the relative freedom of passage across international boundaries by people, capital and products ended with World War I and the situation remains unchanged in a greater part of the world. While this same war upset international economy, the depression of the 1930's caused the collapse of world trade, and exports from all countries fell to an alarmingly low figure. Some countries almost ceased to export. Chile, for example, reported a drop of 88 pct in exports. Countries with

Jan 1, 1952