Search Documents

By R. F. Jones, N. E. Truitt, M. Prats

In most published discussions and theories of in situ combustion, the combustion fronts are assumed to be vertical. However, evidence from field tests leaves no doubt that combustion fronts often advance more rapidly along the top than near the bottom of a formation as a result of difference in density between injected air and formation liquids. The approximation proposed in this paper to determine the movement of the resultant tilted combustion surfaces states that the vertical rate of movement of combustion surfaces is proportional to the horizontal oxygen flux. Where self-ignition is possible, the proposed method demands that a secondary combustion surface exist around production wells which produce some oxygen. These secondary combustion surfaces may be formed long before the primary combustion surface can advance from injection to production wells. Heat liberated near production wells at these secondary combustion surfaces can contribute to an early increase in production rate. Results indicate that significant oil recoveries cannot be obtained from the usual flood patterns (five-spots, seven-spots, etc.) without producing large volumes of unused oxygen. Ideally, to increase oxygen- consumption efficiency, well patterns should allow oil production from a first line of production wells and gas production from more distant lines of producers. However, it may be desirable to produce some gas at all wells to support (and benefit from) active secondary combustion surfaces. Results indicate that the well spacing through which combustion can be advanced is larger than that predicted by other methods. A large number of production wells may still be desirable to take quick advantage of gravity drainage. From a comparison with results at South Belridge field, California, it appears that this method adequately describes oxygen concentration and temperature histories and combustion-front shapes. However, this method does not accurately locate the most advanced point of the combustion surface. There is some field evidence to substantiate the actual presence of secondary combustion surfaces at South Belridge. Use of the proposed method appears warranted at this time when lay-over of the combustion surface can be anticipated. INTRODUCTION The assumption of vertical combustion fronts has been embodied in all previous publicationsl-6 which use the movement of combustion fronts away from injection wells to determine the temperature and fluid distributions in the reservoir. The only paper concerned with a mathematical model of the combustion process in which a nonvertical combustion front is used was written by Gottfried.11 Actually, nonvertical combustion fronts have been observed in most in situ combustion field tests for which adequate data are available.7, 8, 6 In practice, the typical vertical extent of the burned zone decreases with distance from the injection well, and this burned zone is at or near the top of the sand body. In some cases, such as at South Belridge field near Taft, Calif., the combustion surface is almost horizontal over a very large area.8 Thus, for some years an obvious and serious gap has existed between theory (vertical fronts) and practice (tilted fronts). This is indicated in Fig. 1. Tilted combustion fronts such as observed at South Belridge8 sometimes result from the natural tendency of injected gases to rise to the top of an oil sand. An initially present gas cap, even if thin, would make apparent the effect of gravity segregation from the first, particularly since formations considered for in situ combustion field operations are generally selected for their

Jan 1, 1969

By E. D. Levine

A study was made to delineate the dislocation mechanistns controlling prismatic and basal slip at low temperatu.ves in titanium containing approximately 100 ppm interstitial impurities. Mechanical tests were performed on single crystals prepared from electron-beam zone-refined crystal bar by a thermal cycling technique. Measurements were made of critical shear stress and activation volume as functions of temperature. The study revealed that, for prismatic slip, two overlapping thermally activated processes aye rate-controlling below 300°K. From absolute zero to 220°K, reasonable agreement is obtained between experiment and the mechanism which involves overcoming 01. the Peierl's stress by the formation of double kinks in dislocation lines lying in close-packed directions. Between 220°and 300°K prismatic slip is controlled by a difierent thermally activated process which is characterized by a stronger temperature dependence of critical shear stress. Above 300OK, prismatic slip is controlled by an athermal process. Basal slip is controlled by a thermally activated process between 195' and 400°K. An approximate analysis suggests that it is the Peierl's mechanism that is rate-controlling in this range. Below 195°K, the occurrence of mechanical twinning obscures the features of basal slip. Above '400 X, basal slip is controlled by an athermal process. TITANIUM, an hcp metal with a less-than-ideal axial ratio of 1.587, deforms primarily by {1010}( 1210) slip at low temperatures.'-3 The critical shear stress is strongly affected by the presence of interstitial impurities. For example, churchman3 reported that a decrease in the combined nitrogen plus oxygen content from 0.1 to 0.01 pct decreased the critical shear stress for prismatic slip from 9.19 to 1.4 kg per sq mm at room temperature. Basal slip, however, is less strongly affected by interstitials; Churchman's data for {0001}( 1210) slip show a smaller decrease in critical shear stress from 10.90 to 6.3 kg per sq mm at room temperature, for the same decrease in interstitial content. In the present study, an attempt has been made to delineate the dislocation mechanisms controlling prismatic and basal slip in titanium. In view of the strong effects that impurities may have on at least some of these mechanisms, experiments were performed on material of reasonably high purity, so that comparisons could be made with investigations on material of both lower and higher impurity contents. EXPERIMENTAL PROCEDURE Single crystals were prepared from 1/4-in.-diam electron-beam zone-refined crystal bar, furnished by Materials Research Corp. The analysis of the zone-refined material is given in Table I, indicating that the interstitial content is of the same order as the purer of the two materials investigated by Churchman. The Vickers diamond pyramid hardness number of this material was 85.6. This value agrees quite well with the correlation between hardness and interstitial content proposed by Ogden and Jaffee.4 On the basis of hardness, the material investigated in this study is, therefore, intermediate in purity between that studied by Churchman (Vpn = 97) and that studied by Spangler and Herman (Vpn = 62.4).5 Single crystals were grown by thermal cycling through the a-ß transformation. Two-in.-long by 1/2-in.-diam bars were heat-treated in vacuum for 4 hr at 1160°C. The temperature of the furnace was then lowered to 865°C, and the specimens were maintained at this temperature for 7 days. This procedure was repeated several times, resulting in the growth of individual crystals up to 14 in. in length. Specimens for testing in direct shear along either {l010}(1210) or {0001}(1210) were obtained by electrical-discharge machining. The specimens were in the form of cylinders 1/4 in. in diam by approximately 1/2 in. in length, with a reduced section 1/8 in. in diam and a in. in length. All specimens were electropol-ished subsequent to electrical-discharge machining. The ends of the test specimens were cemented in stainless-steel collars. Shear tests were conducted in an Instron Tensile Tester at various temperatures from 4.2° to 508°K. Measurements were made of critical shear stress and activation volume. The latter measurements were performed by measuring the change in flow stress upon cycling the strain rate between ?1 = 2.62 x 10-3 per sec and ?2 = 2.62 x 10-4 per sec. Activation volume, I)*, is defined as u* =ßkT [11

Jan 1, 1967

By James Park

The principal gold-bearing formation is of volcanic origin, consisting of a great accumulation of andesitic lavas, tuffs, breccias and agglomerates of lower Tertiary age. These rocks everywhere bear evidence of having been subjected to the prolonged leaching-action of thermal waters, doubtless accompanied by steam and acid vapors. They are found in all stages of decomposition or alteration; and in many mines the hard blue andesite can be seen to pass by a series of almost insensible gradations into a soft, or fairly hard, greyish yellow or blue

Jan 1, 1900

By H. G. Doll

THIS paper discusses a method and apparatus for determining the dip of formations traversed by a drill hole, by means of electrical measurements in the hole. The process consists in recording the Spontaneous Potentials present along three oriented generatrices in the hole. By comparison of the three curves thus obtained, after application of a correction factor to compensate for any deviations of the hole, the dip angle and the dip direction are determined. Excellent accuracy is obtained for dip angles over 10°. Because the method is simple and the apparatus rugged, the measurements are rapid and reliable; consequently, they can be made at all the levels that are of interest at any time after the well has been drilled. Mechanical cores are not needed to evaluate the dips. A convenient, timesaving procedure is to perform the dipmeter survey at the time the electrical log is taken, using for both operations the same cable and truck. Actual examples of results obtained in wells of the Gulf Coast area are given.

Jan 1, 1944

By Royal Jackman

Two comprehensive papers have appeared regarding the forms of copper that occur in smelter slags, one by Frank E. Lathe1 and the other by C. G. Maier and G. D. Van Arsdale.2 These authors comment on other published results and draw conclusions from their own investiga-tions. The development of X-ray examination of minerals and improve-ment in high-power microscopic methods make it possible today to get additional evidence by means that were not available to earlier investi-gators. The present work was confined to reverberatory slags obtained from five different plants. Some definite conclusions were reached regarding the forms of copper present in these slags. In most cases these agree with some of the findings of Maier and Van Arsdale but new methods of attack were used in the investigation.

Jan 1, 1933

By Charles S. Barrett

THE experiments reported in this paper have been fruitful in disclosing the mechanism of the deformation of iron in compression. They have established the nature of "deformation bands," "etch bands," or "X-bands," that have been a recognized but little understood feature in the structure of cold-worked metals since the early days of metallography, and have shown the role of the bands in the development of preferred orientations by cold-working. The work has also shown the relation of the orientation of individual grains to the preferred orientation of the aggregate. Some of the methods previously used in the determination of the indices of slip planes and slip directions are shown to be untrustworthy in the presence of deformation bands. The conclusion is reached that many slip planes and slip directions must operate during each stage in the compression of a single crystal, and that theories failing to take account of this require revision. In conducting the experiments a method of compression has been used by which extreme reductions can easily be reached, even to the limit set by the metal's capacity to deform without fracture. The work is a portion of a research program on the plastic properties of iron and steel. It is being used as a foundation for studies of orientations resulting from recrystallization and is being extended to other metals and other types of deformation. PREVIOUS WORK The previous experiments are few and have given confusing results. Ono1 compressed a polycrystalline alpha-iron specimen between two flat plates of a testing machine and found that severe deformation oriented the crystals into a duplex preferred orientation, one set of crystallites having a cube diagonal of the body-centered cubic lattice parallel to the compression axis, and another set having a cube axis parallel to the compression axis. We shall speak of this structure as a. double fiber texture of the type [111] + [100]. Wever2 also made an X-ray determination of the texture

Jan 1, 1938

By C. H. Herty

The reactions that occur in the basic open-hearth process are complicated and are subject to many different factors such as temperature, slag composition and rate of boiling of the bath. It is difficult, therefore, to present an extended theoretical discussion of open-hearth operations without confusing the theory of the process with the application of the theory. This paper attempts to present some of the theory of the open-hearth process without mentioning theory at any point, simply giving some of the practical applications of results founded both on theory and practice and on experimental work both in small and large furnaces. It is hoped that an answer to a number of questions commonly asked by the open-hearth operator may be found in this paper. Discussion of the subject matter is taken up more or less in the order in which a heat ie worked, beginning with the oxidation of the scrap charged, sulfur absorption by the scrap, calcination of the limestone, and extending into the pig iron for the charge, the slags formed during the process, and some of the phenomena occurring in deoxidation of the steel and in its action in the molds. Oxidation of Scbap When scrap is charged into a furnace it immediately begins to oxidize, Oxidation is carried out by.three reactions: Fe + H20 + FeO + Hz (absorbs heat) (1) Fe + C02 + FeO + CO (absorbs heat) (2: Fe+ ½O2 + FeO (gives off heat) (3: The product of oxidation contains some Fe3O4, but FeO usually predominates on account of the iron present in close contact with the scale formed For a given type of scrap the amount of oxidation is controlled by thc fuel and by the excess air being carried in the furnace, the temperature 01 the furnace, and the length of time that the scrap is in contact with the furnace gases. In general, less oxidation occurs when the furnace is rur hot so that the scrap melts rapidly. More important in operation thar the two variables atmosphere and temperature, is the type of scrap being

Jan 1, 1929

By Paul Beck

IT is well known that the hardness of metallic single crystals, like that of polycrystalline metals, increases during deformation (hardening by cold-work). It is also known that, as a consequence of deformation, the metallic material acquires an evident thermodynamic instability, revealed, for example, by the fact that the increased hardness gradually decreases with time, especially at elevated temperatures (softening by annealing). The temperature at which the stabilizing process begins is different for various metals, and for any metal it depends on the amount of deformation. Such stabilization of deformed metals may proceed in two different ways: through recovery, and through recrystallization. The former process allows the unstable deformed metal body to approach stability gradually and without visible change in the grain structure; the latter process, like an allotropic transformation, yields directly the undeformed stable "phase" in the form of new undeformed crystals, which, starting out of a certain number of nuclei, grow into and' consume' the deformed hard material. The extent of stability attainable through recovery is limited, espe-cially if the deformation of the metal crystal or crystals involves not only the gliding along slip planes, but also the bending of the slip lamellae, or at any rate the bending of comparatively large parts of the crystal lattice. In such cases, for instance in bent single crystals or poly-crystalline metals subjected to any deformation, recovery will not as a rule be able to restore the "straight" undeformed lattice, and stability can be attained only by recrystallization; that is, by the consumption of the bent crystal lattice parts by new, undeformed crystals-a much more drastic process. It is evident that the part of the surplus free energy stored in deformed crystals, which is present in the form of the elastic energy of the bent lamellae, is in these instances not considerably involved

Jan 1, 1937

By F. L. Wolf

The catenary system of line construction possesses so many desirable characteristics from the operating standpoint that it has wide application for all types of electric traction. Many steam roads are electrifying sections of their lines, and in most cases are operating both steam and electric locomotives over the same track. This means that the overhead catenary system is subjected to the severe corrosive action of locomotive smoke, and data concerning the resistance of various alloys to this form of corrosion are very desirable from every point of view. Reliable and specific information and data on the subject of corrosion due to steam and smoke from locomotives are extremely meager and, on this account, extensive service tests, together with accelerated tests, have been made on a number of commercial metals and alloys. The observations and data recorded in this paper are the result of a preliminary test which was started in 1923 and which has been carried on to the present time. The recognition of the need for even more detailed and accurate data has resulted in the undertaking of another test which has been in progress for about a year. The result of this test will be published in due course. Some years ago The Ohio Brass Co. was asked by one of the large steam railroad companies to furnish data on construction details for a catenary system which it was considering for one of its divisions. The selection of materials which would give the necessary physical characteristics as well as withstand the severe corrosive action of locomotive gases caused electrical railroad engineers considerable concern. At that time, there were available no specific or authentic data on these important questions: no systematic investigation of the problem appeared to have been made, even though it's importance was generally recognized. Such observations as had been made were crude in that they had been limited largely to visual inspection which too frequently is most misleading. However, the scattered information which was collected gave important clues as to how best to start an investigation. Technical literature was studied, metallurgical experts were consulted, and the problem was discussed with engineers who were in close contact

Jan 1, 1930

By L. A. Roe

The flotation of fine particles less than five microns in diameter and the flotation of liquids from liquids generally requires bubble generation methods different than methods used in dispersed air type machines used in mineral flotation. Conditions in the separatory zone in mineral cells are generally more dynamic as compared to the quiescent conditions often absolutely necessary for the flotation of fine particles and liquids. An example of quiescent flotation with very fine bubbles is the lithium flotation plant which operated at Trona, California for 34 years, until it ceased operations in 1978. A review of the process development and the commercial flotation operations at Trona is given in this paper. The clarification of oil field brines by flotation of the oil from the brine has been used for over twenty-five years. Recent installations related to the Prudhoe Bay oil field and the Alaska pipeline are described.

Jan 1, 1980

H. H. Bleakney (Dept. of Mines and Technical Surveys, Ottawa, Canada)— The work of Dr. Machlin and his colleagues at Columbia University is so scholarly that one hesitates to take issue with them. Nevertheless the writer feels compelled to enter a demurrer to the mechanism of intercrystalline cracking proposed in this paper. The principal obstacle to its acceptance is found in its preoccupation with purely mechanical influences and its disregard for the chemical effect of impurities. The writer believes that the destruction of metallic cohesion by concentration of impurities at the grain boundaries is a necessary and sufficient condition for the development of intercrystalline cracking; and he believes that discussion of the numerous mechanical explanations proposed should wait until some valid objection to the chemical hypothesis has been advanced. It is nearly twenty years since Gillett" drew attention to the possibility that the chemical influence of precipitation might be the cause of intercrystalline cracking. As early as 1935, Greenwood'" remarked that grain-boundary precipitation of impurities in lead appeared to promote intercrystalline cracking. Again in 1939, Scott commented as follows on a paper by Thielemann and Parker:'" "There are at least two familiar phenomena that can influence grain-boundary cohesion: 1) intergranular oxidation; and 2) grain boundary precipitation. An important consideration in this work, therefore, is to determine which, if either, of these factors is responsible for the low values of cohesive strength observed." In 1952. the writer presented evidence," some original and some abstracted, which indicated that in copper, silver, aluminum, lead and iron, intergranular cohesion was a function of the purity of the metal. In 1954 Glen, discussing a paper by Ridley and Tapsell14 indicated his belief in a precipitation mechanism for the intercrystalline embrit-tlement of molybdenum steel and suggested that with an absolutely pure metal it would be almost impossible to obtain an intercrystalline crack. This suggestion has

Jan 1, 1959

By M. Prats, D. G. Russell

The performance of a well in a bounded, layered reservoir with interlayer crossflow has been investigated mathematically. The system studied comprises a centrally located well in a bounded cylindrical reservoir composed of two layers of contrasting physical properties. The reservoir contains a single fluid of small and constant compressibility. In the case of a well producing at constant pressure, the production rate of the crossflow system declines exponentially after the early transient behavior dies out. For wells which produce with constant rate, the pressure-time relationship is linear following the transient. For very early production time, the production rate of the two-layer crossflow system behaves as that of the two-layer stratified system (the case in which the layers are in communication at the well only). Except for early time, in most practical cases the performance of a two-layer reservoir with cross-flow can be duplicated by that of a single-layer reservoir. The equivalent single-layer reservoir must have the same pore volume and the same drainage and wellbore radii as in the two-layer case. In addition, the equivalent reservoir must have a "kh" (permeability x thickness) product equal to the sum of the "kh" products of the respective layers in the crossflow system. If the porosity and permeability distributions are known, the production and pressure behavior of a well with and without crossflow can be predicted. From a comparison of the observed pressure or production performance of a well and the theoretical behavior, the occurrence of interlayer crossflow can be detected. INTRODUCTION When flow is possible across the bedding plane from a low-permeability layer into an adjacent layer of moderate or high permeability, the earlier depletion of the more permeable layer will cause such flow to occur. If this situation exists, the oil recovery from tight layers can be appreciable; thus, the economic ramifications of interlayer crossflow are apparent. The possible importance and extent of flow between adjacent and connected layers — whether resulting from capillary, gravitational, or viscous forces — have been the subject of considerable speculation for many years. Jacquard1 presented a rigorous analysis of the crossflow due to single-fluid expansion occurring between two adjacent and connected layers when the well produces at constant rate. His presentation was entirely mathematical, however, and no numerical results from evaluation of the mathematical solutions were presented. Our objectives in the preparation and presentation of the present paper are essentially twofold— (1) to analyze the behavior of a well which produces a single compressible fluid from a bounded, layered reservoir with interlayer crossflow, and (2) to present practical numerical results and simplified formulas to facilitate engineering analysis of reservoirs with crossflow. The constant-terminal-pressure case was analyzed rigorously, whereas the constant-terminal-rate case was treated only for semisteady-state conditions. DESCRIPTION OF THE IDEALIZED TWO-LAYER RESERVOIR The reservoir to be studied is assumed to be bounded and cylindrical in shape, with a completely penetrating well at its center. The reservoir is composed of two adjacent horizontal layers between which fluid is free to flow. Each layer is assumed to be homogeneous, isotropic and completely filled with a fluid of small and constant compressibility. The total thickness of the reservoir is small enough

By Frank M. Monroe, James R. Cost

The solubility of nitrogen in vanadium is determined from 275" to 575°C by measuring the height of the nitrogen internal friction peak of equilibrated V-N alloys. The proportionality constant at 275°C between the internal friction peak height (Q- 1) and the atom percent nitrogen in solution is found to be 0.095 per at. pct for nitrogen concentrations up to 0.8 at. pct. The heat of solution of the nitride in vanadium is 5500 cal per mole. The solubility of nitrogen in the Group V metals is discussed. LITTLE work has been performed on the vanadium-nitrogen terminal solid solution. Hahn1 found the solubility for nitrogen to be very small and reported the existence of a hexagonal phase of composition near that of V2N at the solubility limit. Rostoker and Yamarnoto2 reported the solubility to be at least 3.5 at. pct at the melting point and to be less than this value at 900°C. In addition, they reported from X-ray diffraction studies that nitrogen in solution produces tetragonality in the vanadium lattice. An X-ray study by Schonberg3 has confirmed the results of Hahn but indicated that the tetragonality observed by Rostoker and Yamamoto was due to the presence of oxygen in their specimens. Beatty4 has performed lattice parameter and hardness measurements on terminal solid solutions and found the upper limit of the solubility to be at least 0.66 at. pct N. No measurements have been made of the pressure-temperature-composition relationships (P-T-X) for the terminal solid solution. As a part of a research program on gas-metal equilibrium, an attempt was made to study the P-T-X relationships in the V-N system using both the internal friction and the gas equilibration methods which have been successful with the Nb(Cb)-N and Ta-N systems (see Ref. 5 for a review of this work). Extensive investigation, using the gas equilibration methods, showed this method not to be applicable with vanadium This was presumably due to the gettering action of vanadium sublimed on the walls of the Sieverts apparatus. Thus, the nitrogen pressure relationships with temperature and composition were not obtained. The internal friction methods were, however, found to be applicable, and the temperature-composition relationships are reported in this paper and compared with similar results for the Nb-N6 and Ta-N7 systems. The existence of a Snoek internal friction peak due to nitrogen in solution in vanadium has been clearly demonstrated. 8-10 Powers and Doyle found the peak to be at approximately 275°C for frequencies near 1 cps.8 In a subsequent paper10 they reported the proportionality constant at 275°C between the internal friction peak height (Q-1) and the concentration of ni- trogen in solution (in atom percent) as 0.06 per at. pct. The studies of Stanley and wert9 indicated qualitatively that the height of the Snoek peak decreased with aging at the peak temperature and thus suggested that internal friction methods were suitable for study of the solubility. EXPERIMENTAL METHOD The vanadium for this investigation was of particularly high purity. It was obtained from the Ames Laboratory of the U.S. Atomic Energy Commission, Ames, Iowa in the form of a 1/2-in. diam, three pass zone-refined ingot. The electrical resistivity ratio (p300ºk/p4ºk) was 160. The initial composition was determined as follows: Carbon 200 ppm Oxygen 150 ppm Chromium <50 pprn Iron 125 ppm Silicon <50 ppm Other metallic 100 pprn The initial vanadium ingot was fabricated to 30-mil wire by swaging and wire drawing without the need of intermediate annealing. Lengths of this wire were then further purified (particularly for oxygen) by outgassing at 10-6 torr at 1400°C for 4 hr. The outgassing treatment resulted in specimens with a bamboo grain structure and a lustrous appearance. Desired amounts of nitrogen were added to the outgassed wires in a Sieverts apparatus in which known amounts of nitrogen were equilibrated with the wire at 1300°C. Nitrogen concentrations were produced in the desired range from less than 1 to 10 at. pct N. Monitoring of the partial pressure of nitrogen in the Sieverts apparatus indicated that at 1300°C equilibrium between the nitrogen gas and the vanadium was obtained within 10 min. Relatively rapid cooling from the nitrogen addition temperature was obtained simply by turning off the specimen heating current and cooling to room temperature in the partial pressure of nitrogen. Internal friction measurements of wire specimens were made under forepump vacuum in a torsional pendulum at frequencies near 1 cps. The torsional pendulum was of low thermal inertia and was designed so that specimens could be heated both by a conventional tube furnace and by the joule heating of a separate current through the wire specimen." Use of a static atmosphere of helium gas as a quenching medium made it possible to cut the specimen current, rapidly cool the specimen to the measurement temperature, and make a measurement of the internal friction in less than 1 min. Because of the large solubility of vanadium for nitrogen, the internal friction peak heights were in some cases greater than Q-1 = 0.1. This high damping resulted in an estimated relative uncertainty in the damping measurements of approximately 10 pct. X-ray analyses made to identify the precipitated ni-

Jan 1, 1970

By D. Bergekoff

IN the routine examination of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of nonmetallic inclusions in both hard and soft steels, obtaining a scratch-free surface with soft metals, and avoiding the usual relief effects with very hard specimens such as tool metals con-taining various carbide and nitride phases. It is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work.

Jan 1, 1939

By John C. McDonald

CONTROLLED cold work is used between solution heat treatment and precipitation heat treatment for producing certain tempers of the commercial aluminum base alloy 2219 (designation of the Aluminum Association, U.S.A.) which contains 6.3 pet Cu as the major ingredient responsible for the age hardening. The complete composition limits for this alloy are listed in Table I. The alloy has been described in detail,&apos; and the control of the heat treatment has also been published.2 Beneficial effects of such cold work in other alloys have also been pointed out.3&apos;4 NO data have been published on the effects of varying amounts of cold work under fixed aging conditions. In connection with an investigation of the possibility of providing the desired cold work by explosively generated shock waves, it became desirable to investigate the effect of variable cold work, and to compare the re -sults with those obtained from explosives. The general principles of explosive hardening are well-described in the literature.&apos; All material used was guaranteed by the supplier

Jan 1, 1968

By Leonard Greenburg, William B. Harris, Gustäv Werner

HAULAGE in tunneling operations generally has been done with electric locomotives. As a rule, on short hauls the source of electricity is a storage battery mounted on the locomotive, which, of course, must be removed and recharged periodically. Where the distance from the recharging point to the tunnel face is very long, and where loads are heavy, trolley-driven locomotives are used. Diesel engines have been used in mining and tunneling operations in Europe for a number of years. The recent reports of studies in Belgium1 and by the Bureau of Mines in this country2-4 have indicated the potentialities of this form of power for haulage, mucking, bulldozing and many other underground operations. The hazards attending the use of Diesel engines in more or less closed spaces have long been known. The exhaust constituents that may create a harmful or objectionable environment are carbon monoxide, oxides of nitrogen and sulphur, carbon dioxide, aldehydes and smoke. Lack of precise information regarding the concentration of these gases and the ventilation requirements to reduce them to safe levels has to some extent suppressed their general acceptance in tunneling and mining work. Not until the work of the Bureau of Mines referred to above, and certain experience gained in the construction of the Delaware Aqueduct,‡ has there been available the requisite information regarding the conditions under which their use may be permitted. This paper concerns itself with the successful operation of Diesel engines underground in the construction of certain parts of the Delaware Aqueduct, and describes the conditions under which Diesel engines have been found to operate with a minimum production of noxious gases. The test data reported were obtained during the operation of Diesel engines over a period of two years.* STUDIES BY THE NEW YORK STATE DEPARTMENT OF LABOR Exhaustive tests were made by the Division of Industrial Hygiene, of the composition of the exhaust gases given off by a Diesel engine mounted on. a test block. These tests showed that certain quantities of the gases are discharged from the exhaust. On the basis of these figures, preliminary requirements of design and control

Jan 1, 1942

By R. A. Meussner, C. T. Fujii

Chromium solution in wustite depresses the oxygen activity in a nonideal manner and expands the lattice slightly. Gravimetric measurements of the equilibrium compositions of wustite containing 0.00 to 1.38 wt pct Cr define the oxygen potential (CO2-CO atm) and the limits of the phase field at 1000°C. These data extrapolate to a maximum solubility of 2 wt pct Cr. The lattice parameter data, room-temperature measurements of quenched samples, differ significantly from those in the literature. Both pure and chromium wus-tites contract at uniform and equal rates as the oxygen content (metal deficit) increases. The a. US metal deficit relationships are straight lines showing none of the curvature previously reported. At constant metal deficit, the a. expands by 0.002? on alloying with 0.4 to 0.5 wt pct Cr but is insensitive to further chromium additions: a small expansion rather than a marked contraction. These results require a modification of the accepted alloying mechanism. IN the high-temperature oxidation of Fe-Cr alloys in Ha-H,and CO2-CO atmospheres the vapor transfer of oxygen from the continuous wustite outer scale to the porous inner scale/alloy interface sustains the high oxidation rates.1"3 The driving force for this transport is the difference in the oxygen activity of the outer wustite and that at the inner scale/alloy interface. In pure CO2, as well as in CO2-CO atmospheres, carburization of the alloy accompanies this oxidation. Current efforts to evaluate the parameters controlling this carburization have shown that the process is not simple; i.e., the carbon concentration in the alloy initially increases rapidly, reaches a maximum, and then decreases slowly as the oxidation time is extended. This is the same pattern reported by McCoy for the more complex oxidation-carburization of stainless steels and an Fe-Cr alloy in CO2 at lower temperatures.4 These changes in the carburization process occur while the overall oxidation rate and the lattice parameters of the scale layers remain constant. If this invariance of the lattice parameter is assumed to indicate a constant scale composition and thus a constant oxygen potential, the carburization results are not easily explained. Electron microprobe traces across the thickness of these outer scales, however, have revealed distinct chromium gradients penetrating 10 to 50 µ from the inner surface where the chromium concentrations were estimated at a few tenths percent. The variation of the chromium cmcentration on the inner surface of the scale, and the resulting change of the oxygen activity, during the oxidation process is considered to be important in defining the carburization process. Thus, to gain an understanding of the complex oxidation-carburization proc- ess, it was necessary to measure the properties of wustite containing known amounts of chromium (chromium wustite). Although the general features of the Fe-Cr-0 equilibrium diagram between 900° and 1300°C have been fairly well established by Richards and white: Wood-house and White,6 Seybolt,7 and Katsura and Muan,8 there have been no detailed studies of the limits of the chromium wustite phase field or the properties of these alloyed wustites. The recent results of a limited study of chromium wustite by Levin and wagner9 indicate that more than 0.67 wt pct Cr is soluble in wustite above 850°C and that this alloying is accompanied by a substantial lattice contraction. This change in the lattice parameter was not evident in the X-ray diffraction patterns of wustite layers from the oxidation experiments;1,3 the lines were sharp even though a chromium gradient existed in the scale. The present paper describes gravimetric equilibrium experiments which delineate the boundaries of the chromium wustite single-phase field at 1000°C and define the changes in the oxygen activity and the lattice parameter of wustite as functions of chromium and oxygen contents. The lattice parameter data of chromium wustite obtained from these equilibrium and special quenching experiments differ considerably from those reported.9 Those for pure wustite show significant differences from the widely accepted data of Jette and Foote.10 Since the causes of these differences are not easily assignable, and since the literature contains many sets of data on wustite which if not in conflict are at best not in harmony, the experimental procedures are discussed in the present paper. EXPERIMENTAL Oxide Preparation. The specimens used in these studies were porous pellets compacted from high-purity (Fe,Cr)2O3 or Fe2O3 powders. These powders were prepared from electrolytic chromium (99.8 pct purity) and electrolytic iron purified by consumable-electrode, vacuum arc-melting processing (299.9 pct purity).11 The oxides were produced by standard analytical procedures: solution of the metals in acids (HC1, then HNO3 added), coprecipitation of the hydroxides (NHaOH), and filtering and washing these precipitates. Initial dehydration of the coprecipitated hydroxides was done in a porcelain evaporating dish heated by a Meker-type burner, final dehydration by firing in a recrystallized alumina crucible at 1000" to 1050°C for 20 hr in an electrically heated furnace. Spectrographic analysis detected the following impurities: silicon, 0.01 pct or less; aluminum, 0.001 pct to trace; manganese and copper, 0.0001 pct to none. Each of these levels is at least one order of magnitude lower than in commercially available CP grade ferric and chromic oxides. Fluorescence analy-

Jan 1, 1969

By P. G. Shewman, T. L. Wilson

Using published surface-diffusion (D,) data and published sintering equations, it is shouln that surface difusion should dominate the neck-growth stage of intering for all materials in which D, has been measured (six metals and A1as). Also, grain boundary diffusion can be expected to contribute appreciably to shrinkage and possibly to neck growth below some critical temperature of the order of 70 pct 01- the absolute melting temperatuve. In view of the widespread conclusion in previous sintering work that volume diffusion dowzinates neck gvowth, experiments were conducted using spherical copper powders to test this conclusion. Scaling studies on neck growth at 950°and 1020°C clearly demonstrated that suyface diffusion dorninates. Kinetic studies on shrinkage gave more equivocal results that indicated an increasing role of&apos; grain boundary transport at lower temperatures. Five diarszeters from 100 to 300 u were used in the scaling sludy and a temperature range of -650&apos; 10 950 C was covered in the shrinkage studies. All experiments were conducted in dvy hydrogen. In 1949, Kuczynski published his now classic paper on the determination of the transport mechanism in sintering from the time laws of neck growth. In the interim, these laws have been applied to many systems and slightly modified by several authors. Essentially all these authors concluded that, for crystal- line materials, the dominant transport mechanism in neck growth is volume diffusion. This stems from the observation that the neck radius increases about as t"5 and that the activation energy approximates that for lattice diffusion. A related but independent series of studies stems from Mullins&apos; rigorous analysis of the growth of the groove formed where a grain boundary meets a free surface." xperimental work stemming from this analysis has shown that for each crystalline material studied (Au, Ag, Cu, Ni, Fe, Pt, Al2O3) surface diffusion was clearly the dominant transport mechanism for groove widths up to the order 10 to 20 p. The ratio of the quantity of material being carried by lattice diffusion to that carried by surface diffusion increases linearly with the groove width, so surface diffusion is dominant for all widths under 10 to 20 u. The analysis of the relative contributions of surface and volume diffusion to grain boundary grooving, and to neck growth in sintering, shows that they are quite similar. Thus, using the available surface-diffusion data and the approximate equations of Kuczynski, or the more rigorous recent equations of Nichols and Mullins, 3 it can be shown that the small necks between particles must grow almost entirely by surface diffusion. The purpose of this study was to re-examine the basis for the conclusion that the neck-growth stage of sintering proceeds by volume diffusion. Using spherical copper powders, of several different diameters, precise experimental measurements were made of both neck growth and shrinkage. Application of Herring&apos;s scaling laws to the neck-growth data clearly indicated that neck growth occurred by surface transport, even though the neck radius increased as or Using the recent analysis of Mullins and Nichols as well as published data on surface diffusion, it is shown that the observed time law, as well as actual rate of neck growth, can be satisfactorily explained by a surface-diffusion mechanism.

Jan 1, 1967

By L. D. Rickets

The principles on which an art is founded are usually few and necessarily basic in nature, but he who wishes to achieve the power to select his aides and give success to important undertakings that may be entrusted to him in the future must ordinarily undergo years of drudgery in order to gain the experience that will enable him to distinguish such fundamentals through the haze of reenforcing detail that clothes and tends to disguise them. This especially applies to those who would dream dreams that may come partly true. Professor Henry B. Cornwall of Princeton was a graduate of Freiberg with mining experience in Mexico. He was my friend and mentor during my college life. In 1883 I finished my postgraduate course and had two offers of work to consider. His advice is very clear in my mind today. It was essentially as follows: I know something of the mines of Mexico and have crossed through the mountains of the West. The West possesses a vast area of mountain and valley. California has long had its gold mines, the Comstock and Gilpin County followed and now comes the discovery of Leadville. I believe the West, will become a great mining country. You can choose now to teach here or go to the mountains. Were I in your place I would go West and identify myself with mining.

Jan 1, 1932

On the following pages are abstracts of papers published by the Institute during the year 1934 as TECHNICAL PWLICATIONB, CONTRIBUTIONS, m bound volumes and in MINING AND METALLURGY. For abstracts of papers that appear In bound volumes in 1934 but that were published as TECHNICAL PWLICATIONS m 1932 or 1933, see the TRANSACTIONS for 1932 and the YEAR BOOK dated January, 1934. Many of the TECHNICAL PWLICATIONS have been reprinted In bound volumes Information regarding this disposition, and number of pages in each paper, may be found m the list beginning on page 92 Volume numbers are given as listed at the beginning of the index, page 99 The abstracts are grouped as follows:

Jan 1, 1935