Search Documents

The basic methods to remove material from underground mines are to: convey continuously, batch in trucks, or batch in a shaft hoisting system. A critical aspect in shaft hoisting is accurately batch loading the conveyance or skip. During the 20th century, the almost universally accepted method of loading was via a measuring flask. A measured quantity of material was filled into the flask as the conveyance traveled through the shaft and then, when the conveyance arrived at the loading position, it was ædumpedÆ into the skip for hoisting. Two skip loading conveyor systems have been developed in Australia: BHP BillitonÆs Cannington Hoisting System, installed in 1996, is believed to be the first conveyor loading system designed for two skips. Two parallel conveyors were installed with a two-way gate controlling feed onto each belt. Cannington was ideally suited to conveyor loading as the very high ore density and relatively low production rate required a relatively small volumetric storage capacity on the weighed belt. Newcrest MiningÆs Telfer Hoisting System, which is to be commissioned in 2005, consists of a single slewing conveyor loading each skip with 32 tonnes of ore. The development of this system eliminates the two-way transfer, improves the accessibility and minimises the excavation required. While every hoisting system must be considered on its merits, conveyor loading offers significant advantages to the Mining Industry in the 21st century.

Jan 1, 2005

By Singh DP, Singh TN

The present study attempts to critically review the pillar-design as required by Coal Mines Regulations of India vis-a-vis latest rockmechanics formulae. Equivalent material modelling was the approach adopted for testing the safety and stability of the pillar sizes predicted by various formulae. Two parameters, considered here for calculating pillar sizes was the stresses acting over the pillars and the strength of the pillars. Stresses acting on the pillars were calculated by the tributary area method. Based on the studies of Coates and Hustrulid, the stress obtained was reduced by 40 percent. For calculating the strength of the pillars, three formulae, namely Holland and Gaddy, Salamon and Munro and Central Mining Research Station, India, were used. The pillar widths were then determined by equating the product of recommended factor of safety and pillar stress with the pillar Strength.

Jan 1, 1992

The Rock Mass Rating (RMR) and Rock Mass Strength (RMS) classification systems for jointed rock masses are briefly reviewed, with particular reference to their use in slope stability studies. A correlation is provided between the results obtained from the two classifications and an equation is presented tentatively defining the RMR value for long-term stable slope angles. The validity of the equation is discussed in general terms in the context of slope stability problems commonly encountered in Western Australian open pit gold mines.

Jan 1, 1992

A mechanised sub-level overhead benching method is used at Cleveland, to produce 22,000 tons per month of ore assaying 0.92% Sn and 0.40% Cu. The ore occurs in a series of vertical lenses which can be mined by open stoping. Levels are developed at 60ft., vertical intervals by jumbos. The ore is silled out and the stope block formed between levels drilled out by long hole drilling. Each row of holes is fired and broken ore within safe reach from the stope brow is mucked out by Wagner ST-5A Scoop Trams. The remaining broken ore is recovered on extraction of the next lower level. Ore is hauled by road to the crusher station from the mine. As mining proceeds below the lowest surface portal a spiral decline will be used for ore haulage and mine servicing.

Jan 1, 1970

FOR some years past it has been usual to specify high-grade copper for use for many purposes, but the practice of specifying zinc of a high degree of purity for certain purposes is of comparatively recent origin. It is a practice, however, which is extending ag the effect of the impurities in zinc on products manufactured therefrom becomes widely recognized.The notes hereunder are intended to briefly survey the principal uses to which high-gr.ade zinc is being put, and, wherever possible, to indicate the effect of the impurities normally present in the lower grades of zinc.In the United States zinc is graded into five divisions, known respectively as "High-grade" "Intermediate" "Brass Special" "Selected," and "Prime Western." The maximum amounts of impurities allowed in the various grades are indicated in Table I,which is compiled from data published by the American Society of Testing Materials:In addition, it is specified in an cases that the slabs shall be reasonably free from surface corrosion or adhering foreign matter. Although zinc used in Europe has in many cases been sold on analysis it is only recently that any attempt has been made to grade...

Jan 1, 1923

By Thornton D, Firth B, Kojovic T, Brien G, O&apos

Coal fragmentation is a function of coal type and mining process. Each unit step in the mining, handling and crushing chain of coal imparts energy to the material and impacts on size degradation and consequent mineral matter liberation and pla

Jan 1, 1998

By Potter DJ, Firkin GR

The Imperial Smelting Furnace operated by Sulphide Corporation Pty. Limited at its Cockle Creek zinc-lead smelter was recently equipped with tuyeres angled at 25 degrees instead of the usual 10 degrees. This change was prompted by the results of model studies undertaken by tha Research Department of Imperial Smelting Processes Limited, at Avonmouth in the United Kingdom, and by the favourable results of operating trials on the Cockle Creek furnace using bent-tip tuyeres to simulate 25 degree inclination. The use of 25 degree angle tuyeres has made it possible to operate with lower zinc values in discard slag and has improved hearth stability over a wider range of sinter quality and composition.

Jan 1, 1981

With increasing depth of mining, geotech nical factors assume increasing importance in the design and operation of open pit coal mines. Dragline strip mines are particularly sensitive to stability conditions since the draoline is a relatively inflexible machine, particularly in relation to its limited dump- ing radius for overburden disposal. Geotechnical factors relevant to strip mine design include: 1. spoil pile stability 2. wall stability 3. floor stability 4. excavation characteristics 5. groundwater conditions A basic geotechnical investigation pro- gram for new mine feasibility studies is described. This includes: 1. terrain evaluation 2. geotechnical drilling and logging 3. geophysical logging 4. materials testing 5. seismic refraction traversing 6. groundwater studies Such a program will give an overall geotech- nical assessment of the site and highlight any areas which may require further, more detailed Investigations

Jan 1, 1981

By Wu Y. H, Lu J. P

Slope stability has now become a practical tool in the design and oper- ation of open pits. The stability of rock slope depends on many factors, including not only structural geology, the existence of weak layers, ground- water, blasting and weathering, but also the virgin stress field. This paper presents an application of a numerical method to investigate the effect of the virgin stress on slope stability. The finite element method is employed to simulate the excavation of open pits. Redistributed stress fields in the slope of open pit are computed for several different virgin stress fields. Based on the redistributed stress fields, the shear force which tends to produce sliding of a rock mass and the frictional resistance to sliding are evaluated. The possibility of potential failure is assessed by the limit equilibrium method. The combination of the finite element method with the equilibrium method provides a powerful analytical tool for slope stability. The significant effect of virgin stress on the stability of slopes is shown by studying a typical case.

Jan 1, 1989

The relevant characteristic of the evolution of the Pacific continental margin of South America during the Mesozoic-Early Cenozoic has been tectonic segmentation. This has controlled suc-cesive episodes of sedimentary accumula-tion, extrusive and intrusive magmatism and deformation that ocurred at conver-vergent plate edges. During this inter-val, at least three main transverse boundaries played an important role conditioning the existence of paleo-segments of different longitudinal extent at various Periods. These probably correspond to deep-seated faults in the Huancabamba Deflection and at the Arica-Santa Cruz Line; the third boundary projects westward to the Chile Ridge. Tectonic activity appears to have been continous at the Huancabamba Deflection at least since the Triassic. The Arica-Santa Cruz Line was probably an active boundary during the Triassic and Cretaceous; the southernmost boundary may have started to be active at the end of the Jurassic. This tectonic activity has determined the subsidence - uplift and paleogeographic conditions of the paleosegments.

Jan 1, 1990

By Trumpff H

Opencast Lignite Mining requires topwall strata of seams to be fully depleted and footwall aquifers sufficiently depressurized. To prevent a spread of the cone of depression into protected wetlands some distance away, alternatives had been investigated such as closing water works, underground slurry wall barriers and recharge by infiltration. As a result of these investigations, the infiltration method has been chosen and in a first phase during the next decade it will utilize as much as 55 x 106 m3/year. Using this approach, the survival of the wet lands is assured.

Jan 1, 1988

By Boyd G

This paper describes the planning, analysis, design and operational experience of highwall mining based on auger drilling techniques applied to thick coal seams exposed in an opencut highwall. Being the first time such technology has been used in Australia, a large commitment to technical design and logistics planning was given by Callide Coalfields Pty Ltd. This commitment included technical and operations management and supervision, mine services, and the retention of consultants to undertake geotechnical analysis, instrument preparation and instrument installation.

Jan 1, 1991

By Yan D. S

The removal of antimony from a refractory gold-bearing stibnite ore by roasting and selective chlorinating roasting was investigated. The influence of roasting temperature, roasting time, roasting atmosphere and type and amount of chlorinating agents on antimony removal were studied. The laboratory studies carried out included roasting tests of 4 g samples in a laboratory rotary kiln, followed by 400 g samples roasted in a fluidised bed. The test results revealed that antimony was efficiently removed by roasting at temperatures over 800¦C in a nitrogen atmosphere. The most efficient volatilisation of antimony was achieved with the addition of ferric chloride at temperatures between 350-600¦C.

Jan 1, 1995

By Gostylla W

The economic feasibility of controlled district cross-cut recirculation is examined in this paper with particular reference to the most important mine ventilation network parameters. An algorithm is developed to express the annual cost of recirculation which is then compared to the annual cost of conventional ventilation using the University of Queensland Experimental Mine as a case study. The concepts of resistance ratio and volumetric efficiency ratio are introduced and used to analyse the economic feasibility of controlled recirculation within a mine ventilation network.

Jan 1, 1988

The Bulli Seam, New South Wales, cenprises middle to high rank bituminous coal, generally of coking quality. It is worked over an area embracing 300 square miles.Variations in several factors are presented:The seam is somewhat. disturbed and 'dissected by various structural features. This structure, and present topography, have resulted in depths of cover from very shallow to approaching 2, 000 ft in the presently, Worked area. Wide variations of seam thickness occur. Gradations of, rank occur from-place to place. Variations in seam gas content and pride variations in seam gas composition are experienced. Variations in coal strength occur. The influences of these factors on the occurrence of stress and gas phenanena in mining exploration are considered.

Jan 1, 1963

Background BHP Iron Ore Pty Ltd is one of the major iron ore producers in the Pilbara Region of North Western Australia. The company manages three separate joint ventures; the Newman, Goldsworthy and Yandi joint ventures and two 100 per cent owned operations, Yampi and Jimblebar. The Newman operations constitute a mine site at Newman and a 426 km railroad to Port Hedland where there is an ore processing/port site. The Goldsworthy operations currently constitute a mine site at Shay Gap/Nimingarra, a developing mine site at Yarrie, a decommissioned mine site at Goldsworthy and an ore processing/port site at Finucane Island (Port Hedland). The Yandi operations include mining and processing facilities at site and a spur line to join the Newman Hedland railroad. Jimblebar operations are scree and bedrock mining near Newman and include mining, processing and a spur line to Newman where it joins the Newman-Hedland railroad. The Yampi operations constitute a mine/port site at Koolan Island (which is presently being decommissioned). The combined BHP Iron Ore operations produce approximately 46 Mtpa of iron ore. This paper will concentrate on the processes developed and applied for the decommissioning of the Goldsworthy site. The Goldsworthy site is on the northern boundary of the Pilbara Region and adjacent to the western extremity of the Great Sandy Desert. It is located approximately 110 km east of Port Hedland (see Figure 1). The area is generally of low relief with isolated low ranges. The mine site being within the Mount Goldsworthy range area. The geology of the area is essentially Archaean granite with Archaean banded iron formation becoming dominant within the ranges. The chief soils are hard alkaline red soils. The vegetation is essentially shrub steppe with the main hummock grass species being spinifex (Triodia sp). The climate for the region is semi arid tropical. The temperature ranges from a mean low of 15¦C in winter to a mean high of 40¦ in summer. Rainfall is episodic, occurring mainly throughout the summer as a result of tropical depressions or cyclonic activity. The average annual rainfall is approximately 300 mm and annual evaporation may exceed rainfall by up to 2500 mm. Goldsworthy Mining Ltd commissioned the Goldsworthy site in 1965/66. Goldsworthy was the first iron ore operation and associated town site in the Pilbara region. The mine development peaked in 1977 with the town population reaching 1400 people. In 1982 mining ceased and the mining operations were relocated to Shay Gap, 80 km east of Goldsworthy. The Goldsworthy town continued as the base for the railing operations between Finucane Island and Shay Gap. BHP Minerals acquired Goldsworthy Mining Limited in 1990. The population for the town of Goldsworthy at this stage was around 450 people. An assessment of the Goldsworthy site operations concluded that it was uneconomic to continue the operation of the site. The decision was made to transfer the base for railing operations to Port

Jan 1, 1994

The paper describes the geology, structure, stress, gas and strata geomechanical properties for Leichhardt Colliery and their reactions to mining.

Jan 1, 1986

Comminution Kinetics equations are developed to take into account difference of grindability of mineral components. The equations describing both batch and closed circuit grinding or crushing processes are given. These equations are applied to industrial data to derive comminution kinetic and classification characteristics of the component minerals in a multi-mineral ore. Control strategy based on these concepts is presented.

Jan 1, 1985

The paper will review the marked upsurge in the installation of new continuous metal coating lines, both hot dip and electrodeposition. Although some of this new capacity has been replacement for obsolete facilities or directed at traditional markets, eg building products, consumer durables etc, by far the major portion is targeted at the automotive industry. The reasons for the rapid growth of coated automobile panels are discussed. A comparison of the installed capacity with projections for this market indicate that a severe over-supply situation has arisen. Many coatings are now available for the automotive industry, each with their own strengths and weaknesses, but none as yet wholly satisfactory. Coating development has mainly been cost driven. This favours hot dipped coatings, providing surface quality and pressing problems can be overcome. The high cost per unit thickness of electrodeposited coatings has also seen pure zinc coatings being replaced by thinner, more corrosion resistant alloy coatings such as zinc-nickel and zinc-iron. Recently resin overlays have been introduced to improve the performance of electrodeposited coatings. Developments in coatings for the more traditional markets will be described. The fastest growing market in the last decade has been prepainted product for the building industry. This has led to the installation of extra painting capacity and again it appears an excess capacity situation has occurred. Over the same period the traditional zinc coatings have continued to lose market share to the zinc/aluminium alloy coatings, Galvalume and Galfan. These have been joined recently by '1'aiyo Crack-Free which has been taken up by some metal coaters. Galvalume is now widely accepted as being the best available coating for unpainted applications. It is also suggested that 'spin-off' coatings from automotive developments might find a niche in the consumer durable market. The end users of coated products, particularly the automotive industry, have demanded improvements in quality, such as surface smoothness, formability, etc. At the same time the new coating lines have to process wider strip and run at faster speeds. To reconcile these somewhat incompatible needs has required numerous process improvements, many of which need in-line instrumentation and computer control. The more important of these changes are discussed briefly. Finally the paper will describe the recent developments which have occurred in continuous galvanising in Australia and put them into context with the rest of the world.

Jan 1, 1993

By Hayward SB

The Maragorik prospect is an example of high sulphidation, Cu/Au mineralisation occurring at a high level in the hydrothermal system. As extensive ash deposits blanket the region, controlled-source audio magneto-tellurics (CSAMT), in conjunct-ion with bulldozer trenching, have been used to delineate subsurface geology. Fluid upflow has occurred along EW structures dilated by rotation on the bounding major NW lineaments. Rising hydrothermal fluids have exploited permeable horizons in contact with the upflow structures. This lithological control is evident as ledges of silicification and peripheral clay alteration, at high levels in the system. As is typical of high sulphidation systems, a two phase fluid consists of an initial rapidly moving vapour-dominated phase, followed by a liquid-dominated phase. Much of the zoned and overprinted silica to clay alteration is developed from the vapour-dominated fluid. Mineral deposition occurs as a result of brecciation of the competent silic-ification by liquid phase fluids. Such mineralisation is of restricted volume in ledges proximal to the feeder structures.The style of alteration and mineralisation are indicative of a very low temperature and hence a high level system. Thus, although high sulphid-ation systems are inferred to develop from porphyry-related magmatic fluids, such a source at Maragorik is interpreted to be very deeply buried.

Jan 1, 1994