Search Documents

By A Black, A de Jo, J Cavanagh, J Harding

Acidic and metal-rich waters have been discharging from Sullivan Mine, West Coast, New Zealand since the closure of the mine during the early- 1990s. This has resulted in a decrease in pH from a background of 4.5 to 2.8 and an increase in metallic elements in nearby Rapid Stream. In addition to the chemical effects on Rapid Stream, a study of freshwater macro-invertebrates revealed the absence of most biota downstream from the discharge. An attempt is being made to use the Sullivan Mine as a case study of problem and remediation analysis.

Jan 1, 2003

The, Mount Charlotte orebody contains' 5,000 tons per vertical foot-Of'quartz gold ore at an estimated ore reserve grade of )just 'over' 3 'dwt. per ton, Production from it i.s plan ned at a rate of 1,000 tons per working day during 1964.

Jan 1, 1964

By A R. Gerson

Pyrite, chalcopyrite and mixed sulfide samples, with and without quartz (5 wt per cent S), were subjected to column leaching to mimic natural weathering (cyclic wetting and drying). The pH and SO4 2- concentration of the column effluent was measured over a period of 78 weeks. The pH of the pyrite-only containing column rapidly decreased and remained under pH 4 after 12 weeks of leaching. The pH calculated assuming a 2:1 ratio of H + generation and SO4 2- release was slightly lower than that measured. However, a reduced H + to SO4 2- ratio of 1:1 is predicted if the release of aqueous Fe 2+ is assumed rather than the formation of Fe(OH)3. The pH of all columns containing only chalcopyrite or a 1:1 mole ratio of chalcopyrite and pyrite remained at or above pH 5 for the duration of the leach even though significant SO4 2- was released. One column containing the same initial surface area of pyrite and chalcopyrite but only approximately 0.10 the mole fraction of S as chalcopyrite maintained a pH of greater than five for the first 56 weeks of leaching and showed sporadic acid production thereafter. It is well established that oxidation of chalcopyrite results in a surface layer of polysulfide material. It is the formation of polysulfide that neutralises the acid produced on S oxidation through to SO4 2-. Hence where polysulfide formation occurs extensively on chalcopyrite the resulting solution pH decrease will be less than that based on SO4 2- production. The oxidation rate of sulfide minerals increases with decreasing pH and hence acid formation via sulfide oxidation to SO4 2- causes the subsequent oxidation rate to increase. The addition of calcite (CaCO3)to a pyrite column not only neutralises the acid formed but also decreases the rate of release of sulfate to solution by a factor of approximately 30. This is also the case where chalcopyrite is present mixed with pyrite. The rate of release of sulfate from the mixed sulfide mineral columns (after the initial release of the sulfate already present) was between one-fifth and one-tenth that in the absence of chalcopyrite.

Jan 1, 2003

By Fletcher G

This paper will outline the design process, and the constmction and rehabilitation techniques proposed for the external waste dumps associated with the mining of the Wolfang Basin coal measures.The basin is located to the north of Clermont and immediately west of the Bowen Basin in Central Queensland, Australia. Development of the Clermont Coal Mine is planned for the mid-1990s after adequate sales commitments are obtained to allow the project to proceed.

Jan 1, 1992

By J M. Santini, I C. A Streimann

Arsenic is a naturally occurring element in the environment and is toxic to biological systems. Arsenic can exist in the environment in the following redox states, arsenite (+3), arsenate (+5), arsine (-3) and elemental (0) (Oremland and Stolz, 2003). Arsenic is released into the environment by natural and anthropogenic activities such as rock weathering and ore mining, respectively. Such activities result in the release of the soluble inorganic arsenic oxyanions, arsenite and arsenate. The redox state of arsenic in the environment is influenced by a number of factors including, redox potential, pH and microorganisms (Irgolic et al, 1977; Genc-Fuhrman, Tjell and McConchie, 2004). Recently, the ability of microorganisms to influence the cycling of arsenic in the environment has attracted much attention. Microorganisms that can oxidise arsenite and reduce arsenate have been isolated and the mechanisms of arsenic metabolism are currently being investigated. The differences between arsenic resistance and arsenic metabolism are being revealed. The role of microorganisms in the release of arsenic into the environment is of particular importance with arsenic contamination of waters causing the death of millions of people worldwide, due to the consumption of contaminated water (Vasken Aposhian et al, 2003; Islam et al, 2004).

Jan 1, 2004

By Goodheart B

The Australian Mineral Sands Industry has expanded from the initial export of mixed concentrates in the 1930s, through various development stages, to its current position as a leading world producer of individual mineral products and some further processed products. Opportunities for downstream processing of the separated minerals and locating such developments in Western Australia are reviewed, along with the role of the Western Australian Government in assisting resource development projects.

Jan 1, 1986

By F Saloojee, F K. Crundwell

Refractory ores need to be pretreated prior to cyanide leaching for acceptable gold recovery. Pressure oxidation is one method of rendering the ores more suitable for cyanidation. The focus of this work is optimisation of autoclave configuration for pressure oxidation. An autoclave for the pressure oxidation of a feed containing pyrite and arsenopyrite was modelled, using the population balance framework. The autoclave model takes into account feed particle size, reaction kinetics and retention time. Mass balance calculations were incorporated into Cycad Process« software. This allowed for the investigation of different circuit configurations. The base case model consists of a single autoclave. The feed was then doubled and additional autoclaves were added to provide the same residence time as the base case. Four different configurations for the additional equipment were simulated. These were parallel, series, series with inter-stage thickening and parallel-series circuits. The options are compared in terms of extraction and productivity. The parallel circuit behaves similarly to the base case. The series and series-parallel circuits have higher recoveries and productivities than the base case. The series circuit with inter-stage thickening provides the highest extraction and productivity. This is because the thickening reduces the slurry volume and increases the residence time of the solids in the downstream autoclave.CITATION:Saloojee, F and Crundwell, F K, 2013. Optimisation of circuits for gold pressure oxidation, in Proceedings World Gold 2013 , pp 181-188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By G B. Douglas

Lime-based neutralisation has long been the remediation treatment of choice for acidic mine pit waters. While suited to the attenuation of acidity, lime-based neutralisation may be difficult to implement efficiently due to variation in quality and the partial loss of neutralisation efficiency due to armouring. Large volumes of gypsum-bearing sludge may also require mechanical dewatering and transfer to final voids prior to resumption of in-pit mining or closure. Thus, operational costs may be substantially higher than primary neutralisation alone. Lime production also results in large greenhouse gas (CO2) emissions.Hydrotalcites (HT) are a class of Mg-Al layered double hydroxide minerals with the composition Mg6Al2(CO3 )(OH)16.4H2O. A range of other divalent and trivalent cations may also readily substitute for Mg (eg Cu, Ni, Pb, Zn), Al (eg Fe, La, Ce) and metalloids/oxyanions (SeO42-, AsO43 -/CrO42 -, MnO4-) for CO3 into the hydrotalcite structure. A common feature of acid mine pit waters, often overlooked in assessment of potential remediation options, is the frequent predominance of divalent and trivalent cations as a consequence of partial decomposition of both ore and gangue minerals during in-pit wall rock leaching. Thus, given the presence of substantial divalent and trivalent cations in acidic mine pit waters, an opportunity exists to exploit and in effect work harmoniously with the prevailing pit water composition to form a polymetallic hydrotalcite.The utility of hydrotalcites in the remediation of acidic mine pit waters lies in their ability to incorporate a wide range of contaminants; instantaneous formation, often in a single step; simple post-treatment solute composition; rapid settling; low sludge volume; and the potential to form ore-grade precipitates potentially amendable to reprocessing to (partially) recover remediation costs. Examples of hydrotalcite formation as a method to remediate contaminated acidic mine pit waters at laboratory-scale to full-scale will be presented.CITATION:Douglas, G B, 2015. Whither lime? In situ hydrotalcite precipitation as a method of remediation for acidic mine lakes, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By V S. Vutukuri, K Shariar

This paper present a modification of selected strength criteria for coal and rocks containing weakness planes. The three strength criteria, namely, Murrell (1965), Bieniawski (1974a, 1983) and Hoek and Brown (1980) have been assessed for coal (containing weakness planes) by using triaxial strength tests. Triaxial test results indicated that the strength of coal specimens depends on the weakness plane inclination with respect to the principal stress direction. However it is shown that with increasing confining pressure, the effect of weakness planes inclination on the strength of coal specimens is reduced. The constant parameters in the three failure criteria for coal are determined for each weakness plane inclination by using the Datafit computer program (nonlinear regression analysis) and the results are compared with other rock types.

Jan 1, 1999

Since gold was first discovered, mining development in the West Australian goldfields has been heavily dependent on the location of groundwater both for potable and mineral processing supplies . The location of adequate and economic sources of water has been a constant challenge to both explorers and developers throughout the history of the goldfields. The provision of a piped supply from Mundaring in 1903 greatly alleviated pressure on scarce resources, lowered mining costs and permitted the orderly development of infrastructure. However, increases in the demand for water resulting from new mineral discoveries over the past three decades has led to renewed pressures for more local supplies to be established. Wide-ranging groundwater exploration took place in the late 1960's and early 1970's, also, more recently, in support of intensified gold exploration. The collation and interpretation of the hydrogeological data from the whole goldfields region indicates that despite a low mean annual rainfall of between 180 and 350 mm, quite marked differences exist between the rates of groundwater recharge in different parts of the area, In general, these can be shown to diminish in a southerly direction contrary to a trend towards increases in annual rainfall. Recharge rates are related mainly to differences in rock weathering pattern, geological structure and physiography. The same differences have controlled the pattern of groundwater salinity and the magnitude of groundwater storages associated with the palaeodrainages. In the vicinity of the northern and western watersheds with the Gascoyne, the superficial sediments tend to be thin, may have calcrete in the section and contain moderate storages of brackish or even fresh water. This contrasts with the lower regions of the palaeodrainages where calcrete is absent and deeper erosion has permitted the accumulation of relatively large thicknesses of fine-grained sediments which are saturated with hypersaline water and constitute substantial storages. Account must be taken of these characteristics if water supply sources are to be optimised to meet the growing demands for groundwater in the region.

Jan 1, 1988

Stope control information at the C.S.A. mine is obtained by diamond drilling inclined holes from within the stapes. Practical mining outlines are determined from complicated ore contours by a joint mining engineering and geological study. Production holes to achieve this outline are individually marked up and checked. Stope control also extends to selective mucking of ore mixtures for metallurgical reasons and to marginal ore and waste mixtures for economic reasons.

Jan 1, 1969

By M Ogle

"Booster fans are relatively rare in Australian coal mines. However, as mines become progressivelydeeper it is likely that such fans will be increasingly adopted as a method to sustain or improve the ventilation of underground workings. The reasons why booster fans may be an att ractive alternative include: increased cost of sinking additional ventilation shafts with greater seam depths; environmental objections to shaft sinking projects; and increasing urbanisation and surface constraints limiting availability of potential ventilation shaft sites. As Tahmoor Colliery movedinto its northern lease the ventilation constraints became the limiting factor on production. Thelimitations of the old workings meant that the existing ventilation system would be inadequateto sustain the required production. Extensive ventilation modelling was carried out to evaluatevarious potential solutions and the recommended option was the installation of a booster fanor fans, to gain underground access to an already approved shaft site in the northern lease.Proposals were sought from recognised fan manufacturers and various alternative arrangements were tendered. Ultimately the choice was between one large centrifugal fan and a set (three or four) of smaller æauxiliary-likeÆ fans in parallel. The successful tender was for a single centrifugal, an arrangement very similar to the booster fans that have been operating eff ectively at Westcliff Colliery for a number of years. This paper describes the current ventilation network, evaluation of the ventilation options, the fan selection process, and the project status to date."

Jun 1, 2012

By Perring CS, Barnes SJ

The nickel exploration boom of the late-1960s and early-1970s led to the discovery of numerous komatiite-hosted nickel sulphide deposits, associated with variably serpentinised bodies of olivine-rich cumulates. Subsequent research has shown the importance of volcanological processes to understanding the genesis of these deposits. Crucial developments have come through consideration of the fluid dynamics of magmas and magma-crystal mixtures, through observation of the dynamics and geometry of modern day basaltic lava flows, through application of theory and experimentation on the kinetics of crystal growth from magmas, and most importantly from extensive detailed field mapping of komatiitic sequences in the Yilgarn Block and elsewhere. From these studies has emerged a new integrated view of the volcanological setting of komatiite-hosted deposits, and a recognition that a complete continuum of deposit types exists. Nevertheless, komatiite associated magmatic nickel deposits generally fall into two overall types based on the nature of the sulphide ore. In the first type the bulk of the ore is either massive Fe-Ni-Cu sulphide or a variable mixture of massive sulphide and an ore characterised by olivine crystals in a continuous matrix of sulphide occupying between 30 and 75 per cent by volume of the rock (called Matrix Ore). Nickel grades of massive sulphide ore range from 2 - 20 wt% and those of the matrix ore generally fall in the range 1 - 5 wt% (average 2.5 wt%) Ni/Cu ratios of the sulphide fraction are generally >10.

Jan 1, 1996

By M Zhu, G Tranell, N Simkhada, K Jakovljevic, M Wallin

Silicon is a vital element in many products today, such as electronic components, solar devices, high-quality alloys, and many others. The growing global demand highlights the need for the development of sustainable production methods to meet this demand as an alternative to the current carbothermic reduction, submerged arc furnace (SAF) based process. An alternative to this is the aluminothermic reduction of quartz in a CaO-SiO2 slag, which not only reduces direct carbon dioxide emissions but also promotes the utilisation of secondary raw materials such as quartz fines, aluminium dross and scrap as well as secondary alumina (SA) from dross recycling. In the current study, the effects of SA and CaF2 additions to slag on the resulting metal composition and metal yield were explored. Results were compared with thermodynamic simulations using FactSage™ 8.1. Experimental results show that, in agreement with thermodynamic simulations, the silicon content of the alloy is increased, while the Ca is decreased for starting slags where CaO-SiO2 is partly replaced by CaF2. Similarly, the addition of SA to the initial slag results in an alloy with a higher silicon content.

Jun 19, 2024

The Australian Mineral Industry's growth in the last two decades is directly related to the skill and experience of its consultants in mining, metallurgy, geology, finance, management, marketing, and engineering. The role of mining consultants needs to be re-examined, so that the quality of the service they deliver will continue to be adequate for the 1990's. One means of this evaluation is by examining Case Studies in the strategies and difficulties of developing contract and entrepreneurial research.

Jan 1, 1986

By Gente P, Eissen JP, Lafoy Y, Charlou JL

The North Fiji Basin (NFB) is delineated by the Vitiaz trench to the North (paleo sub duction zone, Brocher, 1985), the Vanuatu is- land arc (called before New Hebrides arc) to the West and South, the Hunter Fiacture Zone to the South-East and the Fiji islands to the East (Brocher, 1985 ; Larue et al., 1982 ; Carney and MacFarlane, 1982 ; Falvey, 1978). The NFB is characterized by shallow water depths (about 3 km) (Chase et al., 1982 ; Scla- ter et al., 1972 ; Karig, 1971), high heat flow (average of 2.29 HFC) (MacDonald et al., 1973 ; Halunen, 1979), strong positive free air anoma- lies (Worzel, 1965 ; Kogan, 1976 ; Luyendick et al., 1974 ; Solomon and Biehler, 1969) and a geoid anomaly (Malahoff and Larue, 1979) inter- preted as a geoid swelling. Few refraction data reveal a relatively thin crust and sediment co- ver, and the existence of low speeds in the up- per mantle beneath the NFB (between 7,1 and 7,7 km/s) (Larue et al., 1982 ; Raitt, 1956), which could indicate the existence of active spreading zone(s) in this area (Barazangi et al., 1974). Global seismicity of the SW Pacific clearly de- fines the.limits of the NFB, as well as the Lau basin (Sykes et al., 1969). But one can note the low level of shallow seismicity of the NFB (Ham- burger and Isacks, in press) which concentrates in three distinct trends :

Jan 1, 1987

A summary of the more important work by previous workers is followed by brief descriptions of the rock formations and regional structure. Type examples of the various forms of mineralization are described and the conclusion is drawn that there has been one main period of ore formation, namely, during the "Viti Revolution" in the mid or late Miocene.INTRODUCTIONThe Crown Colony of Fiji is comprised of a group of some 250 islands situated between latitude 160 sand 21 0 S and longitudes 1770 E and 1780 w: By far the greater, part of the total area, 7,083 sq. miles, is contained within the two main islands, Viti Levu 4,053 sq. miles, and Vanua Levu 2,128 sq. miles, and it is to these that most geologists have directed their studies. The most detailed work has been in the Tavua Basin, north coast of Viti Levu, centering about the mining town of Vatukoula and the geology of this area forms the subject of a separate paper by Blatchford (this volume p. 13).The present contribution summarizes geological knowledge of Fiji, at the time of writing (Feb. 1952), with particular reference to the known mineralIzation, but excluding the Tavua Basin. For general descriptions of Fiji's topography reference should be made to the recent works of Derrick and Dunkin.PREVIOUS WORKERSPeriod 1840-1930Prior to the gold rush of the early 1930s the visiting geologists concerned themselves in the main with the struc...

Jan 1, 1953

By Fawcett M

Pine Creek Goldfields Limited (PCG) is rehabilitating the Enterprise Pit to an aquatic habitat and potential water resource. This paper discusses the development and implementation of that plan. Pine Creek Goldfields Ltd's Enterprise Mine is located approximately 230 km south of Darwin. Open cut mining of the orebody commenced in 1985 and continued for eight years with 14 million m3 of ore and overburden extracted. Geochemical testing of exposed rock types in the pit has demonstrated a propensity to produce acid, and dissolved metals. A plan of management has been developed and implemented to minimise the risk of acid formation and improve the overall water quality in the final void. In developing the plan prime consideration was given to reducing the potential for pit water to impact upon the regional groundwater. An interception system was constructed on Pine Creek to divert approximately 9 km2 of upper catchment into the northern end of the Pit. Construction of the diversion system was completed in December 1993 and a comprehensive surface and groundwater monitoring program initiated. The monitoring program and associated studies are also discussed.

Jan 1, 1994

Blasting in Norwegian mines is often carried out by contractors who tend to look for the cheapest solution, without concern about fragment quality. The requirementsfor a contractor are usually only related to the maximum size of boulders and the quantity per month. Even when the owners of the mine are responsible for blasting, very little effort is made to optimise the blasting process. This paper presents test methods which were used and results from small-scale and full-scale blasting tests. In the small-scale tests, cubes 500 x 500 x 500 mm of four different rock types were blasted in a chamber, using two types of dynamite explosive. The velocity of detonation (VOD) for the dynamite explosives was 3000 m/s and 6000 m/s respectively. Three cubes of each rock type were blasted with each type of explosive, and a total of six cubes of each rock type was used. The entire muckpile (approximately 350 kg) was- sieved and weighed after each blast and fragments between 8-16 mm were tested for impact values and flakiness. The results of these tests clearly showed improvement in fragmentation the closer the acoustic impedance ratio of the explosive (VOD x density) over the rock (Cp density) was equal to one. The results also showed that the quality of the fragments (in terms of impact values) tends to be better when the cubes are blasted with the high velocity dynamite.

Jan 1, 1995

By D Bruggemann, F Sereshki

There has been an ongoing research on coal and gas outburst for the past two decades at the School of Civil, Mining and Environmental Engineering, University of Wollongong. Research study began with a humble beginning, initially conducting basic laboratory studies on the coal and gas properties, progressing into the determination of gas content of coal by sorption technique and the effect of gas pressures on coal strength. The present laboratory facilities and research interests are extended to include the study of coal permeability and shrinkage properties and their effect of gas drainage characteristics with respect to gas type, and pressures. All the changes are examined with respect to changing in-site geological conditions of the coal deposit investigated. The aim is to provide a long-term support to industry in establishing a data bank for Australian coal deposit characteristics and properties.

Jan 1, 2005