Search Documents

By Nikaido M, Kanda Y

A rotary type separator has been developed which separates particles on the basis of their shape. This separator was applied to a particle size range of about 50 - 120 ¦m, and to our present knowledge may be the smallest size range ever to be separated. A theory of the separation is given based on the difference of an adhesive force of the particles: the adhesive force between spherical particles and plate is more powerful than that of irregular shaped particles for the same particle size. These facts have been ascertained by the measurement of an adhesive force by a centrifugal method. US and Japanese patents have been obtained on this separator, which consists of a borosilicate glass cylinder of 150 mm outside diameter, 120 mm in width, and an AC electromagnet. The samples used in this study were mixtures of spherical glass particles and non-spherical shaped glass particles. The results are summarised as follows. In the case of mixtures of spherical particles and irregular shaped particles in the weight ratio of 1:1, the spherical content of the spherical product became 70 per cent - 75 per cent, and in the case of 3:1, the content became 87 per cent - 90 per cent, as the result of one separating operation. However, for a mixture of somewhat rounded particles and irregular shaped particles of weight ratio 1:1, the rounded content varied between 58 per cent - 73 per cent. The feed rate of the particles mixtures was about 0.3 g/min. Newton's Efficiency was 20 per cent - 60 per cent. The separator may find application in shape separation of ceramic powder, metal powder or industrial diamond powder.

Jan 1, 1993

By T Takayama, M Matsumura, Y Konno

The steel industry accounts for 14 per cent of domestic CO2 emission in Japan, and iron ore sintering process occupies approximately three per cent. While Fe content in iron ore is gradually decreasing. So, the amount of concentrated iron ore will increase in the future. We have focused on magnetite concentrate as sinter materials, because magnetite can be easily magnetically beneficiated. However, it is experienced that blending magnetite ore resulted in increasing Fe2+ component in the iron ore sinter, which results in lower reducibility. Therefore, promoting the oxidation reaction from magnetite to hematite in the sintering process is countermeasure for reducibility. In addition, this promotion causes increase of oxidation heat, which results in high sinter strength and reduction of coke. It is assumed that the oxidation of magnetite tends to proceed in the cooling stage, where the oxygen partial pressure increases after the combustion of fine coke, but there are few studies on the effect of heat profile, especially cooling path. The purpose of this study is to design the effective sintering heat profile to promote oxidation of magnetite ore, especially, to investigate the effect of cooling path on sintered ore microstructure. In this study, magnetite ore and magnetite reagent were respectively mixed with calcium carbonate reagent. Then the mixed samples were pressed and formed into cylindrical tablets for simulating the adhesive layer of a pseudo particle. Through examining influence of maximum temperature and cooking rate on oxidation reaction of magnetite, we confirmed that the oxidation reaction of magnetite is suppressed at above 1350°C for maximum temperature, compared to 1300°C. Sintering at lower temperature is desirable because hematite is stable below 1350°C in the Fe2O3-CaO phase diagram.

Nov 8, 2021

By T Baumgartl, L Zhou, D Mulligan, L Huang

The rapid production and accumulation of mineral processing wastes in the environment can present serious threats to environmental quality and human health. Phytostabilisation with native plant ecosystems is, in many cases, a preferred option for rehabilitation of mine waste storage facilities. However, much of the literature has focused on species selection in short-term experiments to test their suitability under the often extreme chemical conditions in the wastes without addressing the fundamental requirements – ie hydrogeochemical stabilisation and functional root zones. As a result, successful examples of phytostabilisation of mine wastes such as base metal tailings have been rare, especially if success is defined as meeting the completion criteria of non-polluting and sustainable land system at rehabilitated sites. Conventional capping options to isolate reactive tailings/wastes by using physical break and/or sealing layers are often not reliable in the long term (particularly under semi-arid climatic conditions) and, in many cases, they may not be feasible in the field due to the large areas to be covered and the lack of adequate suitable materials at mine sites. By using sulfidic tailings as an example, we have proposed a new paradigm for phytostabilising mine wastes – ecologically engineered pedogenesis in tailings involving accelerated physical, chemical and biological weathering of tailings minerals to achieve hydrogeochemical stabilisation and the development of soil functions, soil horizons and functional root zones.Ecologically engineering functional root zones firstly requires controlling geochemical reactivity in the wastes (ie hydrogeochemical stabilisation), which can cause polluting effects in the root zone and plant toxicity. By means of ecological engineering, in situ weathering of primary minerals (eg pyrites) in tailings may be accelerated by adding functional materials (eg functionalised biochars and organic matter) in the waste slurry during the process of deposition. This will remove or diminish key risk factors (eg potential acidity in tailings and elevated soluble heavy metals) in the solid phase, before placing growth media for reconstructing root zones and transplanting/sowing target plant species. However, much of the acidity, soluble metals/metalloids and other salts would be transported out of the solid phase into the wastewater, which can be addressed by on-site water treatment facilities during mine operation. The trajectory and state of engineered pedogenesis in the weathered tailings may be manipulated to provide specific soil horizons within future root zones that are dynamically evolved toward fully functional soil subsystem within rehabilitated plant ecosystems.CITATION:Huang, L, Baumgartl, T, Zhou, L and Mulligan, D, 2014. The new paradigm for phytostabilising mine wastes – ecologically engineered pedogenesis and functional root zones, in Proceedings Life-of-Mine 2014 , pp 663–674 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

THE slag from the blast furnaces having been granulated, a representative sample is taken to the sample mill. It is then dried, crushed through a 100-mesh screen, intimately mixed, and packeted for assay purposes.METHOD OF ANALYSISINSOLUBLEWeigh 1 grm. of the finely-pulverized slag into a 3t-in. casserole, moisten with a little water to prevent sticking, cover with a clock glass, and add 20 cc. of hot acid (1 HNOs, 3 HCI, 4 H2 0). Evaporate slowly to dryness on a hot plate and bake (without overheating) until all the gelatinous silica is dehydrated. Cool, add 20 cc. HCI (1-1), and boil gently for several minutes; filter into a 300-cc. beaker, cleaning out the casserole thoroughly with a rubber-tipped glass rod. Wash residue with hot distilled water and transfer it to a No. 1 porcelain crucible. Dry, ignite, cool in a desiccator and weigh as total insoluble matter. Dilute filtrate to 200 cc. and neutralize some of the excess HCI with NHa.OH. Warm, and pass H2S for 15 min. Filter and wash withhot water. Boil off H2 S, oxidize with 5 cc. HNOll , reduce bulk of the solution by evaporation. to about 100 cc., and transfer to a 250 cc. flask.SILICAFuse insoluble residue over a blast lamp in a platinum crucible with three or four times its weight of anhydrous carbonate of soda, for 10 to 15 minutes, or until decomposition is complete. Cool, and extract fusion in an 8-in. evaporating dish with HCI (1-1); rinse crucible and cover with distilled water, and evaporate to dryness over a water bath. Take up dry mass with 10 cc. strong HCI, and then.

Jan 1, 1922

New and more cost-effective methods of haulage and hoisting will be needed to develop the underground mines of the future. A review of the development of technology since the 1950s shows that once mechanised equipment became available it took 25 years for appropriate mining methods to be developed and the equipment made reliable, then a further 25 years to reach todayÆs level of automation and reliability. Suggestions are made about possible areas for ongoing research with the observation that there is little research worldwide into disruptive technologies. A call is made for better organisation and presentation of the opportunities and potential benefits of new underground mining technologies.

Jan 1, 2005

By Casley G. E, Pritchard J

A single slurry fed fluosolids roaster was chosen to replace six multiple hearth roasters in the Copper Smelter at Mount Isa as part of the overall program to increase production from 100 000 to 155 000 tonnes blister copper per annum. The paper describes factors influencing the choice of the unit, problems encountered during the commissioning and details of the present roaster operation.

Jan 1, 1974

By P Aguilera, C Guerrero, M Tucker

With the advent of Electronic Detonator Systems in the global mining industry, as well as the development of high precision pyrotechnic delays, the measurement and analysis of delay performance (usually measured in terms of dispersion about a batch mean û precision, and the deviation of that mean from the nominal detonation time û accuracy), has become an important issue. Through the non-conventional use of existing Velocity of Detonation (VoD) measurement technology, it has been shown to be feasible to measure the precision and accuracy of delay detonator series connected in the same manner as a typical open pit bench hook up. This paper describes the work undertaken to compare and contrast performance results obtained using a range of instrumentation including High Speed Video (HSV) filming, digital counter timing using a Hewlett Packard Universal Counter and a digital VoD measurement device. The results obtained demonstrated the practical feasibility of using the latter technology in order to obtain relatively large amounts of data in a time-efficient manner, with a precision of better than 0.5 microseconds, if required. The results also confirmed the close statistical agreement obtained between the three forms of performance measurement, therefore permitting the substitution of the VoD measurement technique for the more capital cost intensive HSV technique and the slow, sample-by-sample HP Universal Counter method. This paper describes the methodology applied and the results obtained.

Jan 1, 2004

By M G. Wansbone, R Bhargava

The inferred ground conditions for the proposed mined cross passages at the northern end of the Waterview Connection tunnels consist of an overburden of alluvial and residual soils, with mixed face geology of highly weathered to unweathered extremely weak rock. This paper describes three-dimensional (3D) finite difference analyses undertaken to evaluate the stability of the cross passage headings and to validate the proposed sequence of excavation. The analyses undertaken incorporated the influence of the construction of the mainline tunnels and the breakout opening in the segmental lining for construction of cross passages.The stability analyses were carried out using FLAC3D™, version 4.0 (by Itasca Consulting Group) by progressive reduction of shear strength parameters to obtain a failure condition and estimate a factor of safety. For each step of strength reduction, corresponding increments of displacements of several points on heading faces were monitored. The stability obtained from numerical analyses was compared with analytical solutions. Interpretation of results of drained analyses indicated instability of the upper 2 m of heading face within the highly weathered rock mass. Additional analyses were undertaken by including grouted fibreglass dowels to reinforce the heading face. The results of the additional analyses showed significant reduction in displacements and yielding of ground around the face. The proposed temporary support comprised face reinforcement using grouted fibreglass dowels in conjunction with canopy tubes and perimeter support of steel fibre reinforced shotcrete. The stability of the construction sequence, which was related to the specific requirement of the proposed excavation equipment, was validated.CITATION:Wansbone, M G and Bhargava, R, 2014. Analysis of stability and design of face support for cross passages – Waterview Connection tunnels, Auckland, New?Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 339–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A M. Myrvang, B Nøst, N Q. Trinh, I S. B Bergh

The iron ore producer Rana Gruber AS is situated in northern Norway just below the Arctic Circle, and has been producing hematite and magnetite concentrates for more than 60 years. Since the late 1990s, the major part of the production comes from a sublevel stoping underground operation after many years of open pit mining. Despite moderate mining depth, the operations have experienced considerable rock stress problems due to quite high tectonic, horizontal stresses. To manage the problems, comprehensive rock mechanics investigations have been carried out by SINTEF, a major contract research organisation. This has included in situ rock stress measurements, laboratory investigations and numerical modelling. Based on this and practical experience, satisfactory design of vertical and horizontal pillars was achieved. At depth, the ore width increases from 30–40?m to more than 100?m. This, together with a major planned increase in production, called for a change of the mining method. After thorough investigations and considerations, it was decided to change to sublevel caving, very much like the LKAB system. The development of the new system has been closely followed up by rock mechanics measures, including 3D numerical modelling and comprehensive monitoring of deformations and rock stress changes. To achieve a satisfactory caving of the hanging wall, all vertical and horizontal pillars in the sublevel stoping area had to be removed. This has been a challenging task, and the development of the caving has been slow until recently. However, now the caving develops satisfactorily.CITATION:Bergh, I S B, Trinh, N Q, Myrvang, A M and Nøst, B, 2014. From sublevel stoping to sublevel caving at Rana Gruber, Norway – rock mechanical aspects, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 323–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

Truly launched during the 1939-45 war, b¬,osted since by huge increases in demand for food, shelter and manufactures of ill kinds, petrochemicals have rocketed into prominence' all'oVer''th'e world and are accelerating to even greater heights.Manipulation of the hydrocarbons in petroleum or natural gas provides raw materials for a wid.e'variety of plastics, resins, detergents, rubbers, chemical intermediates, fibres and fertilisers. These in. turn.. go into a host of products essential to our way of life.A5 a source of chemicals, petroleum has achieved a high place. because of its abundance, relative.eheapness acid ease "f transport and because it can,be' economically processed.'If a nation's industrial' progress is measured by ' the ' modern yardstick of petrochemical production,'Australia has reasonto be proud, for it now has 1S petrochemical plants worth'156 million, either in operation or under construction.At several locations near Sydney and Melbourne, these plants produce petroleum ethylene, propylene, butadiene and benzene, or convert these building blocks into the three major thermoplastics (polyethylene; polyvinylchloride and polystyrene)-a.nd"S.B.R.synthetic" rubber. "A number bf other imr-ortant petrochemicals, including carbon black, and ammonia, also are made, or-planned...Most petrochemicals find application. in seven principal industries - rubber, fibres, detergents, surface coatings, automotive, agriculture and plastics. They play a .part in many other industries, including mining and metallurgy.In Australia, population growth,.an -incr.easing standard of living, greater industrial activity and the replacement of older materials all should considerably expand the markets for established petrochemical plants and lead to the introduction of new manufactures.Unless thwarted, these positive forces should propel petro-chemicals into a future glittering with promise;' ò 'However, some help for the infant industry seems needed if petrochemicals, while growing with the nation, are to contribute as they can to our national development.

Jan 1, 1962

By Muller M, Ashley PM

Massive sulphide ZnPbCuAg deposits in the Halls Peak district of northeastern NSW are of the submarine volcanogenic type. They occur as a number of small lenses enclosed in shale and epiclastic rocks, in association with felsic volcanics of early Permian age. The deposits crop out in steep terrain near the eastern edge of the New England plateau. Local relief of 700 m and slopes up to 50¦, coupled with an average annual rainfall of about 1000 mm has led to local severe landsliding in previously mined areas. Mining from the 1890's to the 1960's has also resulted in unconstrained drainage of heavy metal-bearing acid waters and physical dispersion of finer grained metalliferous sediments into the Chandler River. Waters emanating from the main landslide area, from underground workings and draining scattered unconfined stockpiles of massive sulphide ore have pH values of 3 to 4 and contain elevated contents of Zn, Cu, Pb, Cd and Fe. Chemical mobility of heavy metals into streams occurs under low pH conditions with Zn exhibiting the greatest dispersion. Increasing pH conditions downstream cause precipitation of Fe phases and coprecipitation of heavy metals. Physical dispersion of secondary metal-bearing minerals into the surrounding creeks results in wt% levels of Cu, Pb and Zn in the stream sediments thereby exceeding the regional background values by one to three orders of magnitude. Areas disturbed by mining are characterised by lack of vegetation, biomagnification of heavy metals into algae and lower plants, and partial recolonisation by metal-tolerant grass species (Snow Grass, Poa sieberana; Blady Grass, Lomandra longifolia). Rehabilitation measures will have to include landslide stabilisation, impervious sealing or removal of sulphidic materials, import of topsoil and revegetation by metal-tolerant, slow-growing native grass and shrub species.

Jan 1, 1995

By J Rola

This paper outlines a laboratory-based design method, founded in critical state soil mechanics, for identification of an appropriate compaction specification to ensure dilative conditions prevail across the design TSF stress range. The method makes use of the critical state line (CSL) and consolidation tests prepared at varying compactive efforts. The CSL and consolidation curves are plotted together in e-log p’ space, with the compaction curves transformed from vertical effective stress to mean effective stress using the coefficient of earth pressure at rest (K0). Consideration is given to the sensitivity of K0 as it is generally not available during the design phase. An example of the design method is illustrated with laboratory data.

Jul 1, 2021

IN preparing a sample of refined lead for analysis, it is necessary to exercise great care to avoid contaminatien, as the amounts of the various impurities present in market lead are very small. The lead is cut into convenient-sized pieces, which are flattened out with a hammer, so that, on putting tbe lead through the rolls, strips of about one inch in width and Ij32iu. in thickness are obtained. The hammer, anvil, and rolls should be carefully cleaned before use. The strips oflead are cut up into pieces of about one inch square. If the lead is roIled out very thin and cut up into small pieces there is considerable risk of the acid acting too violently and causing loss through frothing over. A blank assay on all the reagents used should becarried right through, along with the actual analysis of the lead. This is of the greatest importance, particularly with regard to the determination of such impurities as iron, sulphur, arsenic, and antimony.METHOD OF ANALYSISThe method of analysis is as follows: Take two lots of 600 gIm. each, place in a large beaker, add 2000 cc. distilled water and 750 cc. concentrated HNOs. Cover with a clock glass and warm on a hot asbestos plate until all action ceases. (If any white precipitate forms, filter off and examine for Sn and Sb.) Add 420 cc. H2S04 (1-1), and stir well while adding the acid: Allow PbS04 to settle, pour off the clear liquid into a 12-in. porcelain evaporating dish, and start evaporating down, the dish being placed directly on an 8-in. ring gas burner. Wash the precipitate three times by decantation using approximately 1200 cc. hot water for each washing, and stir well...

Jan 1, 1922

By T A. Short, P L. Brown

Kestrel Mine co-disposes around 1.5 Mt of fine (2SO4/t and to date around 9 Mt has been deposited. The mine plans to co-dispose of approximately 39 Mt of material, creating a dump with a maximum height of 35 m and a disturbance footprint of 260 ha. Benign materials suitable for rehabilitation are severely limited and no successful rehabilitation strategy has yet been demonstrated. A rigorous measurement and modelling program is resolving outstanding issues associated with acid rock drainage (ARD). The objective of the program is to develop and validate a strategy for dump rehabilitation that will control ARD and allow for mine closure. The strategy includes using a soil cover to reduce water flux into the dump to control the overall oxidation rate and to control effluent release. Monitoring of the oxygen distribution and water flux in the uncovered material commenced in February 2001 and monitoring in waste under a trial cover commenced in February 2002. Carbonaceous and sulfidic oxidation rates have been measured. Initial modelling indicates that the carbonaceous material has the general effect of slowing the rate of pyrite oxidation, lowering the maximum sulfate production rate and extending the time to oxidise all the sulfides. The combined approach of measurement and modelling provides a sound basis for assessing the performance of the trial cover and predicting the long-term quality and quantity of effluent at the base of the rehabilitated waste dump.

Jan 1, 2003

By B A. Webler, P Su, P C. Pistorius

Advanced high-strength steels (AHSS) typically have much higher aluminium concentrations (by an order of magnitude or more) than conventional low-carbon aluminium-killed steels. The resulting lower oxygen activity at the steel-slag interface changes the kinetics and thermodynamics of steelslag reactions. Previous work showed that the rapid transformation of alumina inclusions to spinel inclusions, and spinel to periclase, occurs because of the relatively high concentration of dissolved magnesium. In this paper, experimental results on nitrogen removal by ladle slag are compared with predictions based on the available thermodynamic databases. As in previous work, the kinetics was modelled by assuming mass transfer control, with steel or slag mass transfer limiting. The results show that significant removal of nitrogen by steel-slag reaction is possible.

Aug 21, 2024

By K Baker, J Purtill

One of the key challenges for the mining industry globally is the rehabilitation of mine waste, and Queensland is no exception. Out of pit waste structures including waste rock dumps and tailings storage facilities, create novel landforms which require ongoing maintenance and pose risks to the environment and sometimes to communities. Where multiple mines co-exist, such as parts of Queensland’s Bowen Basin, individual mines can often be constrained by adjoining operations. This presents opportunities for broader rehabilitation strategies to be considered, more than the current single mine focus, that may provide better environmental outcomes for a region. Given recent global disasters involving tailings storage facilities, and our team’s endeavours to drive Queensland to achieve leading practice in mined land rehabilitation, we are exploring the potential to maximise in-pit tailings disposal opportunities for coalmines through shared waste management strategies. A shared waste management strategy is where two (or more) mines, owned by different companies and operated under different environmental permits, transport tailings from one mine to the other in close proximity, for disposal in a disused pit. This would reduce the number of waste structures to be built, operated, rehabilitated, and managed in perpetuity. Our objectives are to identify and remove barriers to tailings transfers between sites to:  minimise environmental risk  minimise long-term liability of managing mining waste and associated structures  support improved outcomes for the local community. To determine the scale of coal waste disposal practices in Queensland, internal data and publicly available imagery was analysed by the Department of Environment and Science in 2022. Approximately 6500 ha of land in Queensland is utilised for coalmine tailings storage facilities or codisposal areas, with ≈ 3700 ha of this being out of pit.

Aug 2, 2023

By J Chan, T Baumgartl, A Plante, C Peltre, P D. Erskine

Mine soils are often organic matter and carbon poor due to disturbance, topsoil stockpiling and mixing with spoil. They present an opportunity to observe the accumulation of soil carbon arising from rehabilitation or ‘green carbon’ through organic matter inputs and may be considered for carbon credits. Soil carbon is known to improve multiple soil characteristics and is viewed as an indicator of soil health.When attempting to estimate soil carbon levels in the Australian coal mining regions, both coal and black carbon (BC) need to be quantified. Coalmine soils contain coal particles that are difficult to distinguish from organic matter using standard carbon analyses. BC, a material arising from the incomplete combustion of organic matter and fossil fuels, displays some similar characteristics to coal and is ubiquitous in Australian soils due to bushfires. The presence of coal and BC complicate the determination of green carbon levels in mine soils.A method to quantify coal and BC in mine soils from the Bowen Basin using thermal analysis and multivariate curve resolution is presented. By determining BC and coal contributions it is then possible to calculate green carbon levels in rehabilitated mine soils. Calculated green carbon levels are compared with bulk density as soil quality indicators.CITATION:Chan, J, Baumgartl, T, Erskine, P D, Peltre, C and Plante, A, 2014. Distinguishing carbon fractions in coalmine rehabilitated soils, in Proceedings Life-of-Mine 2014 , pp 491–498 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

With the advent of the resources boom in the late-1960s most of the larger scale resources projects in Australasia were commissioned on an æowner miningÆ basis, where the mine owners owned and operated the primary mining equipment. Then, in the 1980s with the arrival of the gold mining boom in Western Australia and elsewhere, a change occurred û most of the mining activities were carried out on a contract mining basis. Over recent years, however, there has been a marked trend amongst larger Australasian open pit mining operations back towards owner-controlled and operated mining operations. The reasons for this are many and are addressed in the paper, but centre on the concept of the owner being prepared to assume more of the mining risk in exchange for the advantage of not having to pay a contractorÆs profit margin. Where mining contracts are entered into, the older æschedule of ratesÆ format is being replaced with less adversarial and more entrepreneurial contract alternatives involving operating cost and risk sharing in a spirit of æfair dealingÆ. Leasing and maintenance issues have also been influenced in recent years by the advent of more flexible contract arrangements with equipment suppliers. Group purchasing has also had some influence for project operators. For many mine owners, the optimal risk management profile involves a practical offsetting of the assumption of mining risk on the one hand, against the removal of litigation risk and potentially reduced operating costs on the other. Potential pitfalls may arise where equipment size and type requirements vary with time or where manpower management, mining flexibility, job skills or safety exposure factors are relevant. These issues are commented on in the context of some well known examples, and an update is provided on contract mining versus owner operation in large-scale Australasian open pit mining generally.

Jan 1, 2002

By C Moorhead, J Jones

A common problem in the mining industry is that company geologists can operate in relative isolation to the rest of the company (Jones and Moorhead, 2011). This may result in poor knowledge transfer and often priority conflicts with geology, operations and project departments. This problem is amplified by the acquisition of mineralogy capabilities and other metallurgical (met) test work undertaken by many companies in order to solve for complex orebody problems. Met data is often not located and viewed in 3D space so that geologists and engineers can create and work with geometallurgical (geomet) models (Bye, 2006). Visualisation of data in an interactive graphical 3D model provides a bridge enabling met professionals to collaborate with engineers and geologists to provide a common understanding of the relevance of geomet data.In recognition of this problem, Newcrest has undertaken an effective collaboration strategy to improve internal and external engagement through the use of large visualisation displays (Jones, 2009). The displays are underpinned by IT systems and information management practices that recognise the needs of underlying disciplines. Today it is generally understood within Newcrest that this is required to improve decision-making, deliver faster cycle times and improve governance.Collaboration in companies has been generally associated with the introduction of new IT functions (IBM, 2008). However, the science and engineering process that are used to structure modern IT-based collaboration systems and practices are now known to be simplistic compared to the long-standing practices associated with collaboration and knowledge management in disciplines such as geology and mining.CITATION:Jones, J and Moorhead, C, 2013. Geometallurgical communication as a distributed information system, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 133-138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By A Whaanga, A Doecke

The internal stratigraphy of the Marillana Creek palaeochannel Tertiary channel iron deposits (CID) in the Hamersley Province of Western Australia was initially defined in the 1980s and redefined as the Marillana Formation in the early 2000s. Recent drilling, open pit mining and field observations in the Western deposits at BHP Billiton Iron OreÆs Marillana Creek tenements have revealed some additional details on the extent and detail of some units of the Marillana Formation stratigraphy in this area. The drill hole data at Western 1 South has identified a number of features either not previously documented in this area or whose significance has not been adequately recognised, including a denatured zone at the base of the Upper CID of the Barimunya Member, and variations in the lithology within the Munjina Member at the base of the channel. Additionally, the Western 4 pit walls show evidence of a significant near-surface clay horizon and overlying CID, which are suggested to be the equivalent of the Iowa Eastern Member in the Eastern deposits. The deposition of this unit was most likely driven by a regional climatic disruption rather than a change in sediment source area alone. The nature of the Weeli Wolli Formation-derived goethitic peloids in the Western deposits may explain the more extensive denaturing in the Western Lower CID of the Barimunya Member. In contrast, the more robust nature of the haematitic-cored pelletoids in the Central and Eastern deposits has resulted in a less denatured Lower CID in these areas. Such work reveals the value of and need for geologistsÆ ongoing face mapping observations and detailed drill hole logging, and cautions against not querying previously accepted interpretations.

Jan 1, 2007