Search Documents

About 60 persons are admitted to the graduate course every year after passing the entrance examinations. The entire course of studies is free of charge and the universities provide accommodation for the students who need it. The five years of studies are divided into 10 semesters. One semester lasts 15 weeks. Automatics can be studied at three separate faculties. At the University of Mining and Metallurgy, it is offered by the Faculty of Electrical Engineering, Automatics and Electronics as well as the Faculty of Mining and Metallurgical Machines (metrology can also be studied there); at the Silesian Technical University in Gliwice, the Faculty of Mining offers the course. The educational plans and programmes comprise 3 groups of subjects: common for a given course of studies (foreign languages, political science and the basic technical knowledge) common for the speciality and subjects of diploma courses. The whole time of studies covers about 4400 hours excluding 3 periods of professional training and the physical training. The classes, laboratory classes, seminars and design classes are obligatory and the attendance is strictly checked. Students may extend their knowledge by participating and working in the Science Clubs. The students' work is checked not only during the classes but also by the examinations held at'the end of respective semesters. Those who fail the exams can repeat them only if very important reasons are presented. At the very end of the studies there is a diploma examination together with a discussion on the diploma thesis, written by the student. The successful result entitles the student to recieve the title of "magister inzynier",M.Sc. of his speciality. The graduates, after working for 2 years, can attend another course of studies lasting 2 semesters and called "Postgraduate Course", or start "Doctoral Studies" finished by the defence of a doctor's thesis. In'these cases the expenses are usually covered by the graduates' employers.

Jan 1, 1985

By Mishra BK, Agrawala S

The traditional method of scale-up uses the population-balance model. In particular, the selection function values for a material are determined in a laboratory mill and a variety of correlations are used to scale these values to plant scale mills. For example, the factor D2-5L (D-mill diameter, L-mill length) appears in many power correlations. The number of collisions is proportional to the number of balls (aD2L), the frequency of mill rotation ((x 1/4D-) and effectiveness of impact ((XD), which gives rise to the 'D2.5L' expression. However, what is lacking in this expression is that it does not throw light on the intensities of collisions. In other words, the collision intensities in both laboratory and plant scale mills are implied to be identical. This fact has been very limiting. Alternatively, the collision frequencies and intensity of impacts can be computed with the discrete element code. This code computes the motion and collision of each individual ball in the ball charge. Therefore the number of collisions and the fraction of collisions in the energy range Et, E2.òòE. (collision energy density) are calculated for a given mill size and operating conditions. Then, using the breakage function determined in drop-weight experiments, the evolution of size distribution is computed for a lab mill. The collision frequency and energy density for larger mill sizes are shown. The fundamental theory outlined for the calculation of size distribution is equally applicable for the large mill, which is the basis for scale-up.

Jan 1, 1993

The present-day arrangement of old ( ? ) Palaeozoic and Mesozoic metamorphic rocks in eastern New Guinea lends some support to the concept of tens:konal dilation in Upper Cretaceous to Lower Tertiary time, It appears that the metamorphic core of the Morobe Arc (Glaessner, 1950) could have been rifted from the eastern flank of Cape York Peninsula, and then been carried north-eastward by some unspecified sub-crustal. tangential force. In the early stages of the rift it is thought.that submarine basalts may have extruded up the .'tension .scar and spread across the floor of the opening rift. Thick clastic muddy sediments derived almost exclusively from the rifted block were then spread across the floor of the opening rift. Later ~ertiary lateral movements from east to west along the Markham-Ramu Fault appear to have bent the northern end of the Morobe Arc towards the.east,,causing the intense folding in the sediments of the Aure Trough.

Jan 1, 1962

By Boontanjai C, Boyapati ER

Reagents used for batch flotation tests were Aeroxanthate-343 & 350, Dow Z-6, & reagent-4037 (from Benambra) as copper collectors; Na2SiO3 & Na2S2O3as gangue depressants; lime & HCl as pH regulators; and pine oil & MIBC (methyl isobutyl carbinol) as flotation frothers. A Denver Sub A flotation cell of capacity 250 gms was used for the batch flotation experiments. Atomic absorption spectrophotometer was used for copper assays and microscopy for selectivity and liberation studies. Melbourne tap water was used throughout the experiments. Unless otherwise stated, the following parameters apply to the flotation experiments: flotation impeller speed - 1300 rpm, pulp density during flotation- 22%, reagents addition - in 4 stages, total conditioning time for collectors - 8 minutes, total flotation time- 9 minutes. A variable quantity of copper mineral collector according to the test in question was added, then conditioned the pulp for 2 minutes. The froth was removed by hand, scraping the full length of the cell at constant depth every 10 seconds. No frother is required for this copper tailing flotation. Four concentrates were collected after addition of collector and conditioning at 2,4,6 and 9 minutes. The pulp volume was maintained at a constant level to yield a constant froth depth.

Jan 1, 1990

By Whittaker B. N, Reddish D. J

The rockbolting method of support is employed widely in several countries in different of mines. Hard rock mines use this method extensively. Soft rock mines, such as coal mines, have employed standing supports (steel sets) as the main method, although some countries such as the U.S.A. and Australia have preferred rockbolting. There is increasing interest in extending the rockbolting method in coal mines. The application of rockbolting techniques in an industry which traditionally has not applied such techniques, has required the development of a systematic design approach. This design approach uses extensive monitoring, to asses the viability of the support system in differing conditions. Currently at a number of new and existing mine developments in the U.K., rockbolting is being successfully applied. Although, inevitably some localised geotechnical problems have been encountered and have needed to be taken into account. The effect of faulting on roadway conditions is discussed in this paper and a design approach has been applied using a numerical analysis method, namely the Finite Element Method. The results presented in the paper serve as a useful guide to roadway support designers, and in particular the role played by different bolts in a range of conditions.

Jan 1, 1992

By Salehi M. R

Although inherent mineral matter appears to have no effect of the reflectivity of inertinite in the reflecting light microscope, it has a marked effect on the grey levels resulting from the backscattered electron response in the scanning electron microscope. Inertinite with a high inherent mineral matter content has a high grey level response but not as high as that of mineral matter. The highest grey level response is with inertodetrinite which at times could be mistaken for mineral matter. Fusinite has a higher grey level response than semi-fusinite. The backscattered electron grey level response corresponds to average atomic number and hence approximately to density. If a porous structure develops and becomes filled with mineral matter such as S, Cl, Ca, Si, and Al the grey level will be higher. Micrinite has an unusual response in that it behaves like an exinite maceral in the SEM rather than an inertinite maceral. It either has a low grey level when relatively free of inherent mineral matter, or a low grey level background with high level granules corresponding to Si and Al dominantly. Similar structures have been found in exsudatinite and resinite. It is thought that micrinite results from the migration of hydrocarbons out of exinite giving a porous structure which usually accommodates inorganic matter.

Jan 1, 1991

By Hopkins G. M F

Intensive exploration of the Archaean ultra mafic sequence bordering the Kambalda dome has resulted in the discovery of at least ten dis- tinct areas of nickel sulphide mineralisation subsequent to the initial drill intersection in January, 1966. Sulphide ore reserves to June 30, 1972 were 19.36 million tonnes at 3.3% nickel after mining of 3.0 million tonnes at 3:7%,nickel since production commenced in March, 1967. About 75% of contained nickel metal reserves occur in sulphide concentrations located at the base of the-ultramafic sequence, in contact with underlying meta-tholeiitic basalt. The remaining reserve occurs in concentrations of sulphides within the ultramafic sequence, usually within 100 metres of the underlying contact and typically in proximity to contact mineralisation. These hanging wall orebodies are smaller, contain significantly lower con- centrations of sulphide, and generally exhibit higher Ni:S ratios than underlying contact ore- bodies. The majority of contact sulphides concentr- ations form narrow, elongate, north north-west trending bodies, closely coincident with fault bounded depressions in the contact. Detailed study of the Lunnon Shoot ore environment in- dicates that it was a locus of crustal failure during, and subsequent to, emplacement of ultra- mafic rocks. Resultant structures parallel and

Jan 1, 1973

By McCarthy J

In both the U.S.A. and Canada regulations concerning the reporting on mineral resources and especially ore reserves have been established. The regulations are virtually identical for the two countries with the main exceptions being who is franchised to write the report and how the various reserve categories may be used in reports to the public. Both countries divide ore reserves into "proven", "probable" and "inferred" categories. "Proven" reserves are those for material for which tonnage is computed from dimensions revealed in outcrops, trenches, underground workings or drill holes and for which the grade is composed from the results of adequate sampling. "Probable" reserves are those which are less well defined than "proven" while "inferred" reserves are generally those which may exist through geological and geophysical interpretation. The AusIMM/AMIC draft guidelines as proposed for use in Australia define more rigidly the ore reserve categories into "proved" and "probable" terms, which can only be applied following a full and favourable analysis of economic, mining, metallurgical, marketing and sociopolitical factors. If the ore reserves are not supported by this analysis they are placed into a "resource" category. Proper application of this proposed Australian model could prove useful when dealing with grass-root prospects or mining properties in the pre-feasibility stage. Combined with competent reporting, use of the proposed guidelines should ensure standardised and more verifiable analysis/valuation of a company's mineral assets.

Jan 1, 1987

By S L. Simpson, J Waworuntu, B M. Angel

"The Batu Hijau copper/gold mine, operated by PT Newmont Nusa Tenggara, is located in the south-western part of Sumbawa Island, Indonesia, and is situated ~10 km from the south coast at an altitude of ~450 m above sea level. The mine became fully operational by year 2000 and processes approximately 120 000 t of ore per day that contain an average of 0.53 per cent copper and 0.4 per tonne (g/t) gold. Tailings management at the mine includes a deep-sea tailings placement (DSTP) system that discharges tailings through a pipeline via an outfall located at a depth of 125 m at the head of the submarine Senunu Canyon (Figure 1).The environmental impact assessment undertaken prior to approval of the DSTP evaluated both on-land tailings storage facility (TSF) and DSTP options for tailings management. Negative attributes of the on-land TSF included removal of approximately 2300 ha of forest/agricultural land, the potential relocation of >2000 people from their communities, the high average annual rainfall (>2500 mm) and potential for earthquakes presenting challenges for water management and creating a long-term risk of failure. The final choice and Indonesian Government’s approval of DSTP was also influenced by the close proximity of the deep submarine canyon to the mine. The Batu Hijau mine is one of the larger examples of DSTP in the world and deposits tailings at the greatest depth. The depth of the main canyon increases to >2000 m within 20 km of the coast, and to >3000 m approximately 50 km from the coast.The DTSP at Batu Hijau must comply with an environment management plan (EMP) and environment monitoring plan of permit stipulation that approved its commencement in 2000; updated in 2010 and 2015. The environmental management objectives were to avoid impacts to highly productive components of the ecosystem such as coral reefs, mangroves, surface waters and fisheries, and confinement of impacts to areas of low biological productivity. In the vicinity of the DSTP outfall and within the Senunu Canyon, the management plan predicted significant adverse impacts from the DSTP on the marine ecosystem in the form of: reduction in sea water quality due to elevated turbidity and dissolved copper concentrations burial of benthic organisms a reduced habitat for demersal fish.Recovery of the pelagic and benthic ecosystem to preoperating conditions was predicted to occur within the first two years after operations cease. The CSIRO has performed due diligence studies to independently verify compliance with permits and evaluate new monitoring objectives (Apte et al, 2004; Simpson et al, 2010; Angel et al, 2015), and has performed assessments of environmental monitoring data on the tailings footprint and ore stockpile processing against the above environmental objectives (Simpson and Angel, 2015).CITATION:Angel, B M, Simpson, S L and Waworuntu, J, 2016. Long-term monitoring and targeted assessments to improve management of mine wastes – the Batu Hijau project, in Proceedings Life-of-Mine 2016 Conference, pp 81–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By Ishijima Y, Goto T

Displacement Discontinuity Method (DDM), which was originally developed by Crouch,S.L., is a powerful tool to calculate mechanical disturbances due to tabular excavations. Three topics on DDM applications to strata control problems in Japanese deep coal mines are described. First, is numerical simulation of microseismicity induced by longwall mining in Horonai Coal Mine. Microseismicity in the mine had been monitored by a mine-wide seismic ar- ray. Location of microseismic events and in- tensity of seismicity were well simulated. In the simulation procedure based on DDM, first, zones where a failure condition is satisfied by the advance of mining are detected. Then, the seismic moments, which indicate the inten- sity of seismicity, at the failure zones are evaluated. Second, is prediction of the shaft damage due to mining in Sumitomo Akabira Colliery. In this mine, the limit angle of the shaft pillar was changed from 600 to 800 to increase the amount of minable coal volume without increas- ing mining depth. Displacement of the shaft axis has been measured to assess the damage due to mining around the shaft pillar. In the calculation based on DDM, a fault intersecting the shaft and the ground surface are con- sidered. Observed and predicted displacement of the shaft axis agreed well.

Jan 1, 1992

Selective leach analytical techniques applied to surface geochemical samples in the search for deeply buried mineral resources gained popularity in the late 1990s. Several commercial assay laboratories introduced their own selective leach methods, adding to the few established commercial methods at that time. Many of these laboratories promoted their methods with orientation data showing favorable responses to both precious and base metal mineralisation, concealed beneath extensive thicknesses of overburden. However, many explorationists remain confused about the utility of these geochemical methods. This confusion is due primarily to the lack of objective orientation surveys over significant mineralisation, comparing all commercially available selective leach methods and to the lack of a creditable theory explaining the formation of these selective leach anomalies. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. An orientation survey was designed to fill the first void û an objective survey over significant mineralisation. With the help of 17 mining companies and assay laboratories, an orientation survey was conducted over five significant covered gold deposits in Nevada, USA , representing over ten million ounces of gold. Hopefully the results of this survey will help provide fuel for those working on the second void û a theory to adequately explain the formation of these selective leach anomalies.

Jan 1, 2008

Dr. Willett. I will start by answering one or two general points which have been posed. The first point is a question of liability of a seam to spontaneous combustion. Some seams are very liable to spontaneous combustion. Some seams are not liable at all except in most abnormal circumstances, and some seams have a liability somewhere between these two extremes. Dr. J. S. Haldane made the comment some 50 years or so ago that if you try hard enough you can make any coal seam in the world fire spontaneously. Many heatings have in fact occurred because the coal has been allowed to be ground up into a fine state and there has been air leakage through it for many years. This has resulted in spontaneous combustion which would not have occurred in some seams unless conditions had been very abnormal indeed. One comment I heard while listening to the discussions of one team was the importance of encouraging morale and the team seemed to go to the extent of suggesting that this was more important than the actual technical action taken. Though I agree that everything possible should be done to encourage morale, it must be in conjunction with the correct technical method of dealing with the Emergency.

Jan 1, 1973

Towards Improved Hydrocyclone Models - Contributions from Computational Fluid Dynamics

Sep 13, 2010

Current mine ventilation systems have evolved from simple, limited energy, series or multi split layouts motivated by low suction, slow running, surface fans. Concentration of coal production from fewer working places and ventilation splits, and varying needs, hazards and challenges, however, have led to substan- tial changes. Modern ventilation systems, therefore, are more complex, sometimes more interdependent on others, more energy intensive, and are founded on the use of multiple airways and greater suction, higher speed surface ventilators and often booster fans. Intensi- fication of output has resulted also in higher gas emission rates, the wide adoption of fire- damp drainage, and sometimes in particular problems such as spontaneous firedamp emissions. Some coal mines are subject to spontaneous outbursts of coal and firedamp. These and related matters and current practices and developments are leading to discernible trends, potential advances, and further changes in Practice.

Jan 1, 1983

By Simpson D, Skopakow J

This paper is one of the series of papers relating to the Melbourne Underground Rail Loop and specifically describes the structural and architectural design of Museum Station. Structural arrangement, loads and design methods of the major temporary and permanent works are briefly described for the main station and entrance works. Planning of the station concourse area, booking halls and entrances are described together with the selection of finishes for all above and below ground areas.

Jan 1, 1981

By Hansmire WH

The 14.7 km Mt. MacDonald Tunnel beneath Rogers Pass in Canada used both drill-and-blast and machine boring methods. A unique ventilation system provides for diesel operations. The design featured minimum construction support and an unrei.nforced poured concrete lining. The west heading was excavated in a single-stage drill-and-blast operation. The east heading used a TBM top heading with a drill-and-blast keyhole bench. The choice of methods was controlled by varying geology, with up to 1,700 m rock cover. Construction performance and progress are evaluated.

Jan 1, 1987

Naturally occurring organic plastics have been in use for over 2,000 years. Plastics based on chemically modified organic polymers date back only about 100 years, and those based on synthetic polymers about 50 years. The development of ,these two latter groups up to the present day is outlined, and the basic techniques currently available for polymer-building and modi-fication (blending, copolymerisation, quantitative and qualitative struc-tural control, and'si de-group reactions)-are reviewed.

Jan 1, 1962

By Langham B. M

A chemical study of the petrographic components of Greta (Maitland) coal, carried out by the Metropolitan Gas Co. (Melbourne), has revealed an anomaly in the composition of the durain which was thought to warrant petrological investigation.The original study, by the Metropolitan Gas Co., extended over eight shipments of coal received during the winter of 1943.The percentages of the several petrographic components were eslimated by careful handpicking of large samples of each shipment, and analyses were made of the handpicked components, which were also tested as to their gas-making and coking properties.The results are summarised in Tables 1 and 2. At first sight the components of the Greta coal bear a general resemblance in composition to those of other bituminous coals of similar rank, apart from a notable richness in volatiles, which is a distinctive feature of Greta coal. The durain has a typically higher ash content, and lower volatile content than the clarain (Table 1); and the coking behaviour of the four components is typical (Fig. 4).When, however, the analyses of Table 1 are re-calculated on a dry, ash-free basis, an anomaly appears: the clarain and the durain, on this 'pure coal' basis, have practically identical compositions, with the durain containing a slightly higher proportion of volatiles than the clarain (cf. Table 3); but the tar yield of these two components is very different (Table 1). Re-calculated on a dry, ash-free basis, the yield from the clarain is 18.9 gallons of tar per ton, while, that of the durain is 29.0 gallons per ton. The gas derived from the durain is correspondingly richer in illuminants (CH etc) and poorer in hydrogen than that from the clarain (Table 2), and is also notably richer in nitrogen.That the composition of the Greta durain is consistent is proved by the analyses of Table 3, in which the compositions of the respective durains and clarains of eight separate shipments of coal are compared. In most bituminous coals, the durain contains several per cent less volatile matter than the associated clarain, and high volatile content in a durain usually indicates a durain rich in spores.

Jan 1, 1947

In the general planning of this area, provision was made for the distribution over the whole area as required of the following services:(a) Power and lighting from the substation distribution boards 'located in the winder house.(b) Miscellaneous electrical indicating, control and signalling systems.(c) Telephone lines from the main internal automatic exchange located in the changehouse, the town exchange to the automatic exchange and also direct lines from the town exchange to selected offices.(d) Compressed air from the incoming 16-in. air main. (e) Water, both unfiltered and filtered; and the disposal of the following effluents:(f) Sewage from the area to the town sewage system.(g) Changehouse shower water to the regeneration area.(h) Storm water to the general mine surface drainage system leading out to the naturally drained area north of the No. 8 Shaft.

Jan 1, 1957

By Whiten WJ

Although cone classifiers have received little attention in the modelling of mineral processing units they are one of the oldest non-mechanical classifiers. Their use has enjoyed a revival in recent years because of their low cost of installation and operation. In this paper the development of models for cone classifiers is reviewed and a new model is proposed. The experimental work, data collection and analysis are briefly described, and the new model is presented and discussed. The data used in the model development are made up from three distinct experiments using different units in each case. There are 21 data sets from a 3 m cone treating the tailings in a copper concentrator, 24 data sets from a 0.3 m pilot-scale cone, and 29 data sets from a laboratory glass funnel (0.(Y73 m diameter) used as a cone classifier, giving a total of 74 data sets. The model structure was developed from an analysis of particle settling in classifiers, using specialised model building software. The size of a particle settling in a separator and the forced flow through the apex of the cone were related via hydrodynamic dimensionless groups to the operating conditions of the unit. The model predicts the separation efficiency using the following four parameters: efficiency curve shape factor, cut-point, underflow density (per cent solids) or underflow pulp velocity. The model covers a range of feed flowrates from 1.2 to 5000 1/min.

Jan 1, 1993