Search Documents

By Lawrie DC

Finely ground beryl was decomposed by mixing with ground limestone and soda ash andheating at 900¦C for,4-6, hours.The sintered material was then crushed and leached by boiling under reflux with 5N sulphuric acid for up to 4 hours. The liquor containing Be, ; Al, . Fe and, other elements as sulphates, was separated from the residue which consisted mainly of silica and gypsum, either' by filtration or by decantation washing.The clarified leach liquor.was first treated to remove Fed}: , by contacting with a primary amine-kerosene solution in2 counter-current stages. The iron free liquor wa,s then passed to a 4-stage counter-current extraction unit where it was con-tacted with 0.5M di-(2 ethyl hexyl), phosphoric acid (EHPA) in kerosene. The'operating conditions were such that at least 99 p'br cent of the Be and only 7' per' cent of the Al- was, extracted The ,B6`= and. Al were ;stripped from the organic phase by sod-ium hydroxide solution of suitable concentration to form soluble "beryllate" and "aluminate" respectively. Most of the Be was subsequently precipTitated a's Bo(OH)2 by-hoating the alkaline solution to 90C, the Al remaining in solution. After filtra-tion and washing, the Bo(OH)2 could be ignited directly to BeO at about 1000 C or used as a feed to further purification stages aimed at producing "nuclear grade" BeO.A small coaAter-current extraction unit was operated con-tinuously using liquor derived from the sintering and leaching stages. Data obtained in batch laboratory tests were confirmed. A product obtained by ignition of the washed "beryllate" precip-itate contained more than'99 per cent BeO.

Jan 1, 1963

By N Trabelsi, D Bakun-Mazor, Y Ben-Ari

As part of a comprehensive project to develop a remote sensing tool for evaluating the mechanical properties of rocks, one must obtain a rapid indication of these properties using conventional field methods. A common method for evaluating the mechanical properties of rocks in the field is to use a Schmidt hammer, a portable device that measures the rebound (R) of a spring-loaded mass impacting against the rock surface. Since the 1960s many studies have been made to find empirical correlations between the R value measured by the Schmidt hammer and mechanical and physical properties such as uniaxial compressive strength (UCS), elastic modulus, density, and porosity. Despite the existing correlations in the literature, this work is required to establish detailed empirical relationships for the carbonate rock units in Israel. To do so, 150 rock samples were collected from 38 different outcrops of carbonate rock units. In each outcrop, 20 impacts were made using a Schmidt hammer at different but adjacent points. The impacts were done horizontally perpendicular to the vertical rock walls. In the laboratory, we measured the density, effective porosity, water absorption, UCS, and elastic modulus. The rock samples we selected contained a wide range of UCS: from 7 to 270 MPa. Our empirical correlations indicate an exponential relationship between R and UCS and the elastic modulus, and linear relationships between R and density, porosity, and water absorbance. The most reliable index is the average of the five maximum impacts out of the 20 made in each rock outcrop. The correlation equations obtained from this work will make it possible to effectively evaluate the mechanical properties of the intact rock in the field, thereby aiding development of advanced tools for rock mass characterisation by means of remote sensing.

Nov 29, 2022

By P Townsend, F Russell

Palabora Mining Company operates an integrated open pit mine, concentrator, smelter and refinery complex located in the Northern Province of South Africa. The Palabora open pit went into production in 1966, mining 30 000 t/d to produce some 62 000 tpa of copper. With continuous modification and improvement, a mining rate of 82 000 t/d, producing up to 135 000 tpa of refined copper, has been achieved. While these improvements have also enabled the mine life to be nearly doubled, the open pit will reach the end of its economic life by 2003. The Palabora orebody is vertical and the reserve extends to a depth of 1800 m over an area of 700 m by 200 m. Studies to assess the economics of mining the orebody by underground means began in the mid-1980s. These studies indicated that block caving is the lowest cost underground mining method that would generate a suitable return. In March 1996, a decision was made to develop a 30 000 t/d block cave mine that will extend the life of the Palabora Mining Company by a further 20 years. In terms of the relatively high rock strength and the resultant coarse fragmentation that is expected at the drawpoint, the Palabora cave can be considered rather unique when compared to other block cave operations. This paper describes the project in broad terms and details the mining method, particularly with respect to the cavability of the orebody and the design features to deal with the coarse fragmentation. The project commenced in July 1996 and final development of the undercut and drawbells is scheduled for completion in November 2003. This paper describes the status of the project and planning as of April 2000.

Jan 1, 2000

The current quantity of rejects from coal beneficiation in Australia represents 20 to 25% of raw black coal production. Approximately 80% of the rejects are derived from coarse processing for particles in the 200mm to 0.5mm size range. The safe and enviornmentally acceptable storage of coarse coal rejects is of interest to coal mining companies. Additional public benefit would be derived from the utilisation of a waste product as a source of fill material for civil and mining engineering applications. BHP Engineering has taken a leading role in the design for storage and utilisation of coarse rejects from two mines associated with the Broken Hill Proprietary Conipany Ltd. The tailings dam at Stockton Borehole Colliery (N.S.W.) is to be raised and a study by BHP Engineering has shown that coarse rejects are suitable for the formation of the supporting embankment surrounding a compacted clay core. Transportation and storage of coarse rejects at the Thiess Dampier Mitsui Riverside Mine (Moranbah, Qld) is achieved by a conveyor leading directly from the coal preparation plant to a discharge stacker on the crest of the rejects stockpile. Production of coarse rejects was higher than anticipated for the initial dump design. BHP Engineering has completed a review of dump design with emphasis on safe operating conditions for the conveyors and stacker system. Data on the geotechnical properties of coarse rejects from Australian coal mines are presented. Coarse coal rejects are a material which should not be considered as waste, but as a potentially valuable resource for many future applications. Appropriate engineering design for the storage and utilisation of coarse rejects would result in an improved environment and economic benefits for the Community.

Jan 1, 1987

By M P. Sandy, J B. Simpson

The empirical stope design techniques developed by Mathews et al (1981) and refined by Potvin (1988) and others, have gained rapid acceptance in Australia in the 1990s as a simple, æfirst-passÆ means of designing primary stopes. However, it is recognised that these æstability graphÆ methods can only provide broad design guidelines. Recently published stability graphs (Hutchinson and Diederichs, 1996) encompass a wide range of geological environments, which are not discussed, and the influence of time and blasting practices cannot be easily reviewed. The æscatterÆ in the graphs must reflect, to some degree, different operating practices as well as subtle but important differences in the pre-mining conditions that are not adequately accounted for in the æmodified stability numberÆ. Development of a ælocalÆ, site-specific stability graph may overcome some of these problems. At NormandyÆs Golden Grove Operations, Western Australia, detailed reviews of stope stability performance, including Cavity Monitoring System (CMS) surveys, are undertaken for every stope, with the objective of developing a series of local stability graphs, customised to site conditions and calibrated in terms of æAverage Falloff ThicknessÆ (AFT). Cablebolting of stope hangingwalls is used to develop reinforced æbeamsÆ on each sublevel, effectively dividing the full span into smaller, more stable æsubspansÆ. By analysing stope stability performance in terms of fall-off, cost-benefit studies can be undertaken of the effect of cablebolting and other options for modifying stope spans. The approach used to develop the local stability graphs, and their integration into routine stope design procedures at Golden Grove, is described. The experience gained during stope extraction in the Scuddles orebodies has been successfully applied to the Gossan Hill æC-PanelÆ orebody. This methodology should be applicable to other underground mining operations.

Jan 1, 2000

By T Huynh, V Matanitobua, J Zheng, B N. Noller, J C. Ng, H H. Harris

A risk assessment was undertaken of the aquatic ecosystem and bioaccumulation of metals and metalloids in fish at the Leichhardt River, Mount Isa, Queensland. Residual contamination of metals and metalloids in Leichhardt River sediment was assessed and arose from mine practices using river discharge in the 1940s. The ecological risk assessment of sediments involved comparison of the concentrations of heavy metals and arsenic with those of the ANZECC/ARMCANZ (2000) Interim Sediment Quality Guidelines (ISQG). Results indicated that all sites including the background site exceeded one or both the ISQG-high and ISQG-low trigger values based on total concentrations. A lesser number of sites exceeded the ISQG-low trigger values following the 1 M hydrochloric acid extract step, which was used as an indication of bioavailability. An additional risk from particulate matter in river sediment is that acute human toxicity from the consumption of fish contaminated with metals and metalloids is unlikely. The potential risk was assessed by comparing with the maximum levels set by FSANZ (2010) for fish consumption by children and adults. In general, the liver of the fish have higher heavy metal and metalloid concentrations compared to the muscle. Frequent or regular consumption of fish from the Leichhardt River that exceed maximum levels (ML) of heavy metals and metalloids is not recommended. Risk analysis showed that an adult can consume up to 5 kg of fish fillets every day from fish caught at the man-made Lake Moondarra downstream on Leichhardt River and still be within safe consumption levels whilst a child can eat up to 1 kg daily.CITATION:Noller, B N, Ng, J C, Matanitobua, V, Harris, H H, Zheng, J and Huynh, T, ?2014. Assessment of ecotoxicology and health risk from bioaccumulation in fish of heavy metals and metalloids from historical mine practices in the Leichhardt River, Queensland, Australia, in Proceedings Life-of-Mine 2014 , pp 337–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By W A. Take, M McKellar, A Walsh, S McDougall, S G. Evans

Recent tailings dam failures have heightened public awareness of the hazard posed by storage facilities for mining waste, illustrating the need for a more critical examination of tailings dam breach mechanisms and the potential mobility of liquefied tailings. Knowledge from tailings dam breach studies will help improve safety and risk management through more accurate inundation maps, dam consequence classifications and emergency preparedness plans. Tailings dams differ from conventional water retaining dams, although dam breach relationships used in practice rely heavily on relationships derived for breach processes from the latter. Physical modelling offers a controlled environment to advance the understanding of tailings dam breach processes, thereby allowing for modelling of simple geometry and boundary conditions to test hypotheses. The performed experiments investigate prototypical tailings dam configurations and material behaviour, with the objective of validating numerical models that will enable practitioners to better assess and mitigate tailings flows resulting from tailings dam failures. Research conducted in the Queen’s University Landslide Flume at the Coastal Engineering Laboratory has investigated the breaching of 1 m high dams with tailings geometry by overtopping initiated by a v-notch incised in the dam crest. This paper presents the initial results of the next stage of this research comparing the outflow hydrograph following loss of containment caused by shear failure to overtopping initiated by notch flow. The two dam experiments presented are constructed with similar dam and reservoir geometries allowing for a direct comparison of the effect on the outflow hydrograph of each failure event. Preliminary outcomes suggest that although both dam failure events are triggered from separate mechanisms their geometries allow for similar values of Q_peak to be reached. Future work is currently planned to expand the shear test series to explore the influence of failure mechanism on the outflow hydrograph.

Jul 1, 2021

By B J. Wight, R Mackay, S Kim

Improving the understanding of the processes governing ground movements in and around brown coal open cuts is of significant interest for both operating stability and rehabilitation. Brown coal, lignite, is a low-rank coal that is best described as a soft rock, with geotechnical characteristics that derive from its organic origin. It is well-known that low-rank coals exhibit creep behaviour; however, little has been reported on the impacts of chemical processes on brown coal creep behaviour even though organic substances are susceptible to chemical alterations and mining processes will contribute to changes to the geochemical environment; around most mines, groundwater flow patterns are altered leading to enhanced surface water infiltration. Here we study the deformation behaviour of brown coal in response to ion exchange reaction. Our experimental results show that for different ion exchange conditions different characteristics of secondary compression are observed. With the addition of Ca2+, the ratio between coefficients of secondary and primary compression (Ca /Cc) initially decreased, presenting a minimum value at the concentration of 0.005?M, then increased significantly. This implies the importance of ion exchange process for the long-term deformation of brown coal. On the other hand, increasing Na+ concentration did not affect Ca /Cc values significantly over all tested concentrations. The suppression of diffuse double layer was still observed for Na+-treated samples as increasing Na+ concentration decreases Ca values. From a practical perspective, this study did not consider the tertiary creep behaviour and eventual creep failure.CITATION:Kim, S, Mackay, R and Wight, B J, 2014. Creep due to chemical alteration of rocks – a case study in brown coal, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 61–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By G M. Mudd

Mine tailings represent one of the two largest sources of mine waste from the minerals industries (the other being waste rock). Given the problems of declining ore grades and growing production, tailings generation is increasing exponentially across the global mining industry. Common practice is for mines to build large containment dams to store tailings during operations, which are then rehabilitated following mine closure. At some sites, however, the controversial practices of riverine or marine dumping of tailings is still practiced. As recent tailings dam failures have shown, there are legitimate questions being raised about the long-term viability of leaving tailings above ground due to the risks of collapse and failure. At present, it is rare for mines to emplace tailings back into former mine voids following mine closure, most commonly into a former open pit mine void (although a fraction of the tailings may be used for underground mine backfill, this is minor in scale). The approach of in-pit tailings has numerous advantages, such as inherent physical stability, low to negligible acid and metalliferous drainage (AMD) risks, as well as allowing more productive use of formerly mined land. In tropical areas where surface repositories are prone to leakage with potential for AMD and widespread dispersal of radionuclides (in the case of uranium mining), in-pit management provides particularly strong advantages – thorough hydrogeological studies are required, however, to address residual groundwater contamination risks and to establish sound, long-term environmental monitoring regimes for groundwater quality and subsidence issues. This paper presents a study of in-pit tailings management and compares it with surface repositories established in a tropical climate. The comparisons lead to the conclusion that, at least under tropical conditions, in-pit tailings management should be considered as world’s best practice – especially for radioactive uranium tailings.

Aug 8, 2011

IT is generally accepted that for transport of coal underground from different collecting stations, the system of endless rope haulage with remote control is not only one of the safest and most economIcal, but is also one of the most'efficlent in dealing with output.When the coal measures lie in regular planes, the work of laying down such a haulage presents no difficulties. When, however, the dip of the measures is Irregular, or dislocated by faulting, the management is faced with the problem of constructing vertical curves of such a radius that the sag of the rope will correspond with the road bed, and thus obviate the danger of the rope rising and throwing the skips off the track.The direction of the main roads for haulage purposes being ascertained from the plan of the royalty to be worked, the faults or dislocations in the seam are determined for these roads with the greatest possible accuracy by means of bore holes from the surface.From the data thus obtained the haulage road can generally be so graded that the rope will keep on the floor during haulage operations, although the grades may in places be synclinal.The writer confesses that he knows of no accurate formula for calculating the sag of the rope under varying tensions and so determining the safe radius of the curve, and he had to depend upon past experiences under somewhat sImilar conditions.The accompanying sections illustrate a case where the writer has recently installed an endless rope underground approximately 5000 ft. in length, from the foot of a tunnel in which an endless rope delivers the output to the screening plant, and having to negotiate, first a 400-ft. downthrow fault, and later a 32 ft. upthrow.

Jan 1, 1927

By S Brochot

In cases where coarse gold is present in a deposit, it is usual to use the screen fire assay (SFA) method to analyse the samples. There is no doubt that this method is more accurate than the standard fire assay (FA) and reduces the risk to have a systematic bias. Nevertheless, the difference between the analytical errors of both methods can be glossed over when the overall sampling error is added to obtain the measurement error. In that case, the advantage of the SFA cannot justify its higher cost.The current paper attempts to address this question in the case of a gold ore deposit with visible coarse gold in various sampling situations (drill core sampling in exploration, blasthole or chip sampling in mining exploitation). The overall measurement error is estimated taking into account the analytical error and all the sampling error components following the Pierre GyÆs theory of sampling.Firstly, only the last sampling stage is considered when the pulverised sample is processed either to obtain one analysis sample for a FA or to be screened and subsampled for a SFA. The calculated measurement error clearly shows the advantage of the SFA specifically in presence of coarse gold. Secondly, the half core sampling is studied to explain the observed discrepancies when controlling the second half core. Finally, the blasthole sampling is treated using in situ heterogeneity models to show that the relative advantage of the SFA is hidden by the large overall sampling error.In conclusion, the choice of the assaying method is discussed at the light of the overall measurement error and in accordance to the analysis objective.CITATION:Brochot, S, 2012. Standard fire assay or screen fire assay? Application of the overall measurement error approach to choose the most appropriate method, in Proceedings Sampling 2012 , pp 135-142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

The authors have succeeded in providing additional rigour and clarity to the formulation and execution of the dynamic programming algorithm for optimum open pit limit determination. The inclusion of the blocks on the J + 1 column in the search for Pmax, and constraining this search with blocks assigned a value of negative infinity, ensures an optimal solution within the defmed blocks. The effect of the negative infmity blocks is to preclude mining along the diagonal blocks from the first row that they occur in. Figure 1 graphically illustrates the effects of this on the calculation of P. A practical application for constraining mining with negative infmity blocks is the case where the pit outline is defined by lease boundaries and not by the value of blocks to be removed. Any legal, social or physical constraint could be accounted for in the same way.The danger in applying this technique is that the negative infinity blocks will override any other more profitable solutions that may exist. This is in fact what has happened in the example that the authors use. If a further column is added to the left hand side (column -1) and the calculation is carried out again, a more optimal x-section can be found. (If the negative infinity values are removed the same result is obtained.) This gives a pit value of 112 as against the 108 of the authors' optimal pit. This calculation is shown in Figure 2. Lerchs-Grossman optimization is reliable only if there are sufficient columns available to allow "mining" to optimum depth of the ore body and still allow the pit to break out at the surface within the confines of the columns.This author's approach is to create enough columns each side of the lateral limits of the ore to allow the pit to intersect the surface while still within the confines of the block model. Implementing the methods discussed by the authors helps to reduce the number of columns required to achieve this.

Jan 1, 1987

By Derham DW, Newcombe LA

The operations of the Mount Morgan gold tailings retreatment plant were significantly improved in 1984 by the desliming of the CIP plant feed, which reduced cyanide consumption and increased percent gold dissolution. Subsequently, the development of slimes treatment, incorporating gold leaching from slimes solids by copper cyanide complexes in the process water, and gold adsorption on to carbon in an environment lacking free cyanide was successfully implemented. Mount Morgan was initially mined for gold commencing in 1882 on the auriferous ironstone cap to the sulphide ore body. During the history of mining and processing at Mount Morgan the operations have developed through numerous phases of gold and copper production, operating almost continuously through until the final closure in late 1990. The final phase of processing was the retreatment of tailings, predominantly flotation tailings accumulated since the 1930s, for the recovery of gold and minor silver. Tailings retreatment commenced in 1982 with the commissioning of a 10 000 tonnes per day CIP plant to treat some 40 million tonnes of tailings at an average grade of 1.08 g/t Au. The initial operations were hampered by high cyanide consumption and poor gold dissolution on the mixed siliceous/pyritic tailings. The successful development and implementation of the desliming of the CIP plant feed in 1984 (as described by Parsons and Hampshire, 1986) reduced cyanide consumption by 40 per cent, and raised gold extraction by 13 per cent points by virtue of significantly higher dissolved oxygen levels. The finer portion of the reclaimed tailings were deslimed by eighty 100 mm diameter AKW cyclones, with the desliming cyclone overflow thickened in a Warman 30 in diameter thickener for water recovery and slimes disposal. Operation of the desliming plant involved the discarding of a slime fraction representing about 15 per cent of the reclaimed feed. Although gold-bearing, the high content of cyanicides and oxygen consumers within the slime negated any conventional treatment of this stream with free cyanide for gold recovery. The natural lixiviant behaviour of the soluble copper cyanide complexes for gold, which was extremely evident at Mount Morgan, directed efforts in this area. Enhancement of gold leaching with a deficiency or near absence of detectable free cyanide, but with significant levels of copper cyanide complex from recycled process water were examined. Adsorption of this solubilised gold onto carbon in a similarly difficult environment required close examination.

Jan 1, 1993

By Khosrowshahi S

The objectives of grade control remain unchanged but new methods are being developed to attain them. Since the early-1990s, an improvement in the power of mine site computers has made the geostatistical tools of conditional simulation more accessible. Optimisation of the grade control process on mine sites now involves two stages: optimisation of the sampling regime and optimisation of the interpretation of ore and waste boundaries. Optimisation of the sampling regime first requires an understanding of the nature of the mineralisation and in particular the impact of particle size on the sampling precision. This relationship, termed the Fundamental Error of sampling, enables an optimum subsampling protocol to be defined for the sample preparation and assaying. However, the actual sample collection method, whether drilling or trenching, must be correctly selected and the sampling grid should be optimised. The relative costs and benefits of various alternative sampling methods and grids can be determined using the method discussed. The use of the grade control data can also be optimised. In the past ore and waste boundaries were often defined using a linear interpolation algorithm that smoothed the data (such as polygonal, sectional, inverse distance squared or even kriging methods). Frequently the relative impact of ore loss and dilution could not be estimated. Conditional simulation to generate equiprobable alternative maps (realisations) can now be adopted to address these issues. A transfer function is then used to evaluate the similarities and differences between the maps. The Ore Block Optimisation (OBO¬) process is a transfer function that produces a three-dimensional model of the optimal ore block outlines. This provides a clear guide for the mining geologist to refine and mine. The nature of the transfer function and the inputs and outputs are discussed. In the past, reconciliation has been the `acid test' for any grade control system. Any ore blocking method based on conditional simulation can make use of the exhaustive data set to ensure that reconciliation between prediction and production will improve significantly. The OBO¬ method provides a guide to the mining geologist to ensure that the best ore blocks are mined. Misclassification between ore and waste is reduced, ore loss and dilution are minimised (and are measurable) and ore is optimally assigned to stockpiles of various cut-off grades. These advantages significantly enhance mine profitability and control of the mined grade.

Jan 1, 1997

By S Walters

The emerging discipline of ‘geometallurgy’ is not new but is becoming increasingly recognised as a discrete and high-value activity. Geometallurgy involves a quantified and spatially constrained approach to ore characterisation in terms of relationships to critical processing performance behaviours. A key outcome is enhanced economic optimisation of mining and improved risk management tools.Industry recognition of the need for large-scale, integrated research to support this emerging area resulted in commencement of a major ongoing initiative in mid-2005. The AMIRA International P843 ‘GeMIII’ project (Geometallurgical Mapping and Mine Modelling) is a cross-discipline collaboration involving a number of world-class research organisations supported by over 20 industry sponsors.The project is delivering integrated tools and methods which link intrinsic rock characteristics to prediction of mineral processing performance. These indices must be capable of spatial distribution in 3D resource models and incorporation into mine planning and optimisation. A key aspect is provision of new cost-effective tools and methods which can provide the large numbers of measured and estimated data points required to undertake effective modelling and spatial distribution. The integrated methodology and enabling technologies being developed through the ongoing AMIRA GeMIII project are outlined, together with implications for supporting industry best practice.

Sep 5, 2011

By Dobos SK, Gibson GM, Little TA, Sliwa R

Current studies, and analysis of previouslypublished data, have lead to a re-evaluation of the inclusion of the North D'Aguilar block within the "Gympie Province" in southeast Queensland. The metamorphic rocks are part of a Late Devonian(?)-Early Carboniferous subduction accretionary complex and are unconformably overlain by volcanic and coarse-grained clastic rocks of probable Early or mid-Permian age, as well as by Early to middle Triassic rocks of the Esk Rift. Metamorphic fabrics in the basement rocks include not only those that can be related to convergence, but also younger fabrics that may have developed during Late Carboniferous or Permian uplift and unroofing of the accretionary rocks. A predominance of basic schists, some of which are blue amphibole-bearing, and associated fine-grained pelagic and hemipelagic sediments in the Northern D'Aguilar block contrast with the siliciclastic-dominated sediments of most of the accretionary complexes of the New England Orogen. However the similarity of structural style, and metamorphic and igneous history, with adjacent basement blocks, and with other blocks throughout the New England orogen, suggests that the North D'Aguilar block simply represents deeper, probably underplated, levels of the same subduction complex. Uplift and cooling may have been accomplished by extensional faulting during Permian inception of the Esk rift, which flanks the block on the west.

Jan 1, 1990

By M Hilden, G Forbes, Z Ye, M Yahyaei, F Reyes, V Jokovic

Soft sensors offer several practical advantages for the process control of comminution circuits by combining multiple conventional sensors and other data sources with real-time analysis using mechanistic, phenomenological or machine learning models. While there has been a growth in the use of machine learning techniques for developing soft sensors in minerals processing applications, this paper describes advantages and challenges of using soft sensor models developed on the basis of process knowledge. Recent experience with three new soft sensor technologies developed by the authors are discussed. The Mill Filling Inference Tool which has been implemented at several mine sites, compares SAG mill load cell and power draw measurements with outputs of a semi-mechanistic power model to estimate the mill ball and total filling in real time. The progressive wear of the mill liners is modelled, allowing the model to correct the load mass due to the mass loss automatically and to estimate the charge trajectory. This information enables the mill to be operated more confidently near its limits. A coarse-ore stockpile soft sensor as been recently developed using a 3D cellular automata-based model to track ore size throughout the pile, and estimating the live capacity and size at each stockpile feeder to the primary mills. Finally, a hydrocyclone soft sensor is being developed to monitor performance using available hydrocyclone models to estimate the size and flow balance around the cyclone in real time. The model-based soft-sensor approach aims to synthesise and analyse existing data and provide operators and engineers with process- and model-relevant information that can facilitate making better process decisions. Maintenance data has proven useful for model development as it allows soft sensors to automatically adjust and compensate for the effect of progressive wear, for example for mill liners, thus helping the models to maintain calibration throughout the equipment life.

Aug 24, 2022

This paper describes the MillMapper technology developed for condition monitoring of liners and other operational parameters in grinding mills used for mineral comminution, by presenting a case study of its application. MillMapper provides maintenance engineers, operations managers and process and plant metallurgists with quantitative, accurate and reliable condition monitoring data for informed decision making regarding the maintenance and metallurgical aspects of such mills. MillMapper uses calibrated laser scanners for the capture of three-dimensional surface representations inside a mill during a shutdown so as to determine shell, feed and discharge liner thickness at a resolution of several million data points, a procedure that nominally takes five minutes to complete. Once several data sets over time have been collected inside a mill, MillMapper can be used for liner wear, liner wear zone, liner weight, ball charge volume, ball charge weight and intelligent profile tracking over time. Liner tracking in combination with site defined reline and failure criteria and with throughput tonnage data is utilised for change out prediction of each separate liner segment type.

Jan 1, 2008

By D Fargher

BHP BillitonÆs Cannington operation began production in 1997 and is presently the largest tonnage and lowest cost single mine producer of both lead and silver in the world. The original design capacity was 1.5 Mtpa and this has progressively increased via a series of debottlenecking projects in both the mining and milling operations. In 2003, 2.39 Mt of ore was mined, whilst 2.31 Mt of ore was milled. In February 2003 Cannington received approval to expand the project to a sustainable capacity of 2.4 Mtpa. This resulted in underground development into the northern zone, upgrades to the concentrator, increased accommodation at site and power station capacity. The Cannington project development team implemented a partnership approach to the project. Fraser Osborn Engineering and Outokumpu Technology worked closely together with the Cannington team to meet all of the project constraints.

Jan 1, 2004

There are many factors influencing the way in which a mining company disposes of tailings. Some of the more important factors include physical and chemical properties of tailings, cost, availability of dam wall construction materials, type of mining operation, topography and environmental constraints. As a result, the mining industry has seen a diverse and innovative range of disposal methods developed to satisfy the many conditions imposed at tailings disposal sites. This paper discusses a range of tailings disposal methods currently practiced in the mining industries in North America. These methods include various inpit disposal techniques, upstream, downstream and centreline dam construction and zoned earthfill or rockfill embankment construction. The thickened tailings disposal method and the disposal of fine clays are discussed. The importance of improving the depositional properties of tailings to enhance storage capacity, water reclaim, dam wall stability and final reclamation is stressed. It is important that mining companies are made aware of the full range of disposal methods and dam construction techniques available today. Such an awareness will help improve the planning, design and construction of safer and more efficient tailings disposal facilities in the future.

Jan 1, 1989