Search Documents

By A. Ansari

Standard depressants used in the selective separation of copper and molybdenum sulfides by flotation pose environmental and health hazards. In this investigation, the floatability of chalcopyrite and molybdenite in the presence of six well-characterized lignosulfonates was studied through Hallimond tube flotation and adsorption tests. The results define the physicochemical conditions (lignosulfonate type and dosage, pH, presence of ions) for possible selective separation of molybdenite from chalcopyrite. Dissolved polyvalent cations, especially calcium, appear to serve as "activators" for lignosulfonate adsorption on both minerals. From this point of view, the use of lime as a pH modifier is not always appropriate for optimum selectivity since high dosages of lime to produce high pH tend to indiscriminately depress both sulfides.

Jan 1, 2006

By L. C. So, S. Faucher, S. Mostaghel, A. Triwahyuono, D. Sauter, S. -Y. Oh, S. K. Lee, K. Aswin

"Molten hauling and water granulation are the commonly used slag treatment methods in the production of nickel. Water is present in these processes either to accelerate cooling of the dumped slag or in the granulation itself which creates an inherent safety risk of explosions. Even good design and operation are not sufficient to prevent explosions or injuries from occurring. Several dry methods to treat slags have been intensely studied. However, most of these technologies have never been commercialized due to numerous challenges including scalability, cost, low heat recovery efficiencies, and difficulties in heat utilization. Ecomaister-Hatch has recently developed and commercialized a reliable and simple Dry Atomization process, which eliminates water and allows for heat recovery. As part of the development towards other sectors, laboratory-scale and pilot-scale trials have been completed in a number of base metals and PGM facilities. Recently, Dry Atomization of a nickel laterite slag was successfully demonstrated at the laboratory-scale. The current paper introduces the technology and reports the test results obtained from atomization of the nickel slag.INTRODUCTION The processing of nickel laterites produces vast amounts of slag with over 90% of the feed to the furnace reporting as slag. Slag handing is therefore of critical importance to a laterite smelter. Traditionally there are two ways in which the slag is handled (1) Molten hauling, dumping, cooling and quarrying (2) Water granulation, dewatering, stockpiling. There are inherent disadvantages of both methods that will be outlined in this paper. An alternate route of Dry Atomization provides distinct advantages over the two conventional routes that are of particular interest to the nickel producer such as elimination of molten hauling, dumping and quarrying, elimination of water and improved safety. There is also the potential to convert the slag, which is typically regarded as a waste product, into a value added product and the continuous nature of slag tapping makes it amenable to heat recovery. Hatch has recently conducted laboratory-scale test work on laterite slag to demonstrate its viability for Dry Atomization. Results of this work are presented."

Jan 1, 2017

By John C. Wilmot, Robert E. Brewer, Royce J. Smith

In March 2003, Phelps Dodge started up an innovative pressure leach facility for processing copper concentrates at the Bagdad mine in Arizona. This paper describes the development of the concentrate leaching plant at Bagdad and the operational results from start up to present. Optimization efforts and an approach to mineralogical modeling of the concentrate to calculate oxygen utilization are also presented.

Jan 1, 2004

By Jan E. Nesset, James A. Finch, Frank Rosenblum, Rebecca Payant

"Under certain conditions of moisture and oxygen, sulphides can spontaneously heat, a phenomenon known as self-heating. In this paper, we test a hypothesis that galvanic interaction between some sulphides can promote self-heating. Galvanic interaction is controlled by restpotential difference between minerals and their surface area of contact (particle size). In order to decrease rest-potential, four sulphides were tested: pyrite, chalcopyrite, sphalerite and galena. Two series of samples consisting of mixtures of two sulphides, each representing a mass fraction of 50 %, were run in standard self-heating tests. The first series comprised five mixtures, two with low rest-potential difference (pyrite-chalcopyrite and chalcopyrite-sphalerite) and three with high rest-potential difference (pyrite-galena, chalcopyrite-galena and pyrite-sphalerite). The second series was performed on a pyrite-sphalerite mixture at four particle sizes (80 % passing 850 µm, 300 µm, 75 µm and 38 µm). The first series showed that the individual sulphides and the mixtures of low rest-potential difference did not self-heat but the mixtures of high rest-potential difference did self-heat. The second series showed that self-heating increased inversely with particle size (increased specific surface area) and revealed that it was the fineness of the pyrite (high rest-potential sulphide) that governed the self-heating effect, indicating the rate-limiting step is the reduction reaction on pyrite (cathodic mineral). The increase in self-heating with high rest-potential difference and increasing particle fineness supports the hypothesis that galvanic interaction contributes to sulphide self-heating. A possible mechanism based on the hydrogen sulphide hypothesis is proposed where the reduction reaction at the cathodic mineral surface is ferric to ferrous. The understanding gained will be of interest to those involved in storage, shipping and disposal of sulphide minerals.INTRODUCTIONSulphide mineral ores are the major source of most base metals such as copper, zinc, nickel and lead. Once the ore is extracted, the sulphide minerals are liberated by size reduction (crushing and grinding), concentrated by flotation, and the concentrates sent for further processing to extract the metal (smelting and refining). At the various stages from mining to concentrate shipment and tailings storage, the sulphides are exposed to a variety of environments, which under certain conditions of air (oxygen), humidity and temperature can cause them to heat. Since no external heat source is involved, this pyrophoric process is known as spontaneous heating or, more commonly, self-heating. The self-heating of sulphides is associated with oxidation reactions under moist conditions. If the heat generated is greater than the heat dissipated, the sulphides will self-heat and the material temperature will rise. This can make working conditions potentially dangerous as oxygen is consumed from the surrounding air and significant quantities of sulphur dioxide (SO2) can be released (Ninteman, 1978)."

Jan 1, 2011

By C. Graham

Thin Spray-On Liners (TSLs) have been researched and in development for over two decades and yet their fully functional and widely justifiable application in mining has yet to be achieved. While the explanation for this is partly technical, it is also clear that proving and communicating the operational and economic case for why a mine should change from mesh or shotcrete liners to a TSL is not a trivial matter. Evidence must be presented and communicated effectively, that is both obvious and compelling for a mine operator. The paper describes recent work carried out and directed towards this end, with funding from CAMIRO?s Deep Mining Research Consortium and additional support from 3M Canada and ABB Canada. The essential progress that has been, or is in the process of being made, will be described in providing the necessary proof of acceptable or superior TSL performance in the following areas: polymer formulation, health and safety, geotechnical specification, robotic liner application, business case economics and yielding ground support effectiveness. Future plans are also presented to demonstrate the performance of a new 3M composite TSL/yielding bolt support system in underground trials where the substrate rock is intended to fail through a number of mining-induced mechanisms.

Aug 1, 2013

By A. Giacomini, M. Nazem, E. Fathi Salmi

"Numerical simulation of collapse of tunnels in weak rocks is one of the challenging problems in rock mechanics. Collapse can impose technical and financial difficulties during the construction of underground excavations. This phenomenon, particularly in shallow excavations, may lead to propagation of a caved zone toward the surface and formation of chimney subsidence. Chimney subsidence has numerous catastrophic consequences such as the adverse environmental impacts and damage to surface structures in vicinity of excavations. Due to the importance of subsidence in civil engineering, the main goal of this study is to propose an appropriate method for preventing the formation of subsidence in shallow tunnels in weak rocks. The Dolaei road tunnel is investigated as a case study, where a large chimney subsidence has occurred. The geology of the area and the geostructural characteristics of the rock mass surrounding the tunnel are briefly reviewed in this paper. Two-dimensional as well as threedimensional numerical simulations are conducted to study the tunnel stability. Moreover, the effects of staged excavation and pre-supporting method on controlling the ground movements are studied. Outcomes of this study indicate that employing forepoling and staged excavation can be a practical remedy to control the ground movements and prevent the formation of chimney subsidence.INTRODUCTIONPredicting the formation of subsidence, mainly sinkhole subsidence over civil or mining excavations, is a very challenging task. An accurate prediction of subsidence is required for selecting an appropriate control and mitigation system to reduce the level of ground movements and its impact on the surface life (Bétournay et al. 1994; Leca and New 2007). Excavations, particularly in weak grounds, could result in surface subsidence; they modify the in-situ stress conditions as well as the hydrogeology of the area. Construction of unsupported excavations in soft soils and relatively weak rocks usually leads to the formation of a failure zone behind the face. In a very soft ground, the failure zone can extend towards the ground ahead of the tunnel face. Propagation of this zone toward the ground surface results in generation of sinkholes."

Jan 1, 2015

By L. Trytten, S. Bass, P. Nawrocki, J. Mercer

The Sherritt Fort Site nickel refinery and fertilizer plant has been operating continuously since 1954. The ammonia leach process uses ammonia and sulphuric acid, producing nickel and cobalt and an ammonium sulphate byproduct. One of the features of an ammonium sulphate based process is the aggressive nature of ammonium sulphate to concrete and structural steel. After six decades of operation, portions of the structural steel and concrete at the Sherritt facility have become degraded. Infrastructure replacement programs started in earnest more than a decade ago with pipe racks and electrical infrastructure, and have now progressed into building steel. Replacing and repairing this infrastructure within the tight constraints of an operating plant poses several difficult challenges. This paper will outline the approach taken to accomplish this difficult work, and discuss key learnings from the ongoing program.

Jan 1, 2015

By S. J. Haynes

"This paper documents the characteristics of the different quartz veins, and their relation to gold, in the turbiditic Meguma domain of eastern Nova Scotia. Eleven different types have been distinguished in the greenschist facies on the basis of form, internal structure, mineralogy, wallrock alteration and crosscutting relationships to each other and to regional structures. Gold is present as rare visible disseminations in host rock slates and in ore-grade, early-formed veins, that pre-date the formation of upright Acadian folds and intrusions of Devonian granitoids. Four vein types pre-date Acadian folding. Five gold-deficient vein types are associated with Acadian folding (syndeformation); whereas two gold-deficient vein types clearly post-date this deformational event: Previously unreported, wall rock alteration is associated with early crosscutting and semiconcordant auriferous veins. In contrast, early stratiform veins are devoid of wallrock alteration. It is suggested that the auriferous vein arrays formed as submarine exhalitive systems over synsedimentary tensional faults and that the Meguma domain may represent the opening of a basin similar to the modernGuaymas rift .IntroductionThe term ""turbidite-hosted gold deposits"" is introduced to distinguish gold deposits contained within a turbiditic sequence of wackes and shales (or their metamorphosed equivalents) from gold deposits in other types of sediments. Usage and justification for the term is similar to ""carbonate-hosted lead-zinc deposits"" or ""volcanogenic massive sulphides"". A range of different characteristics can be present in individual deposits, some of which may be indicative of specific deposit types in the same manner that volcanogenic massive sulphides can be subdivided into ""Cyprus type"", ""Kuroko type"", ""Besshi type"", etc. Historically, gold deposits hosted by turbiditic flysch were an important class of quartz-vein gold mines in the 19th century. They included the goldfields of Victoria, Australia, Otago, New Zealand and Nova Scotia, Canada. Production from most of these fields had ceased by World War II and interest in this type of deposit waned. However, the recent exploration interest in gold has resulted in both re-assessment of the classical mining camps and the discovery that ""turbidite-hosted"" gold deposits are present in many parts of the world.Mapping of the regional geology and gold deposits of the Megumadomain of Nova Scotia was carried out by E.R. Faribault of the Geological Survey of Canada between 1886 and 1939. Faribault produced a comprehensive series of maps and reports for each gold district, a compendium of which was published by Malcolm (1929)."

Jan 1, 1987

By Jack Zhang, Yunguo Tang, Baodong Zhao

"Rare earth elements (REEs) have numerous key applications in both traditional and advanced technologies. A shortage of some critical REEs is expected due to the discrepancy between the REE abundance in REE deposits and the REE demand from the market. For example, Neodymium, Europium, Terbium, Dysprosium, Erbium and Yttrium are expected to be in short supply. REE recovery and separation from secondary resources such as uranium wastes, heavy mineral sands, and recycled materials can balance the shortfall in a cost effective way.The Saskatchewan Research Council (SRC) is engaged in the development and commercialization of complete REE recovery and separation technologies in Canada. One of SRC’s newest developments is the design and commissioning of a heavy rare earth (HREE) separation pilot plant. The pilot plant uses hundreds of stages of solvent extraction (SX) to produce high purity individual HREEs from both primary and secondary resources.This paper presents the design of an HREE recovery process for the particular case of uranium processing wastes. The separation results of a group separation are reported and discussed, as well as the issues and the challenges of the development, commissioning and operation of the continuous SX pilot plant.IntroductionSignificant amounts of strategic specialty heavy rare earth elements (HREEs) are found in uranium wastes in Saskatchewan. It estimated that about 47 tonne/a of heavy rare earth element oxides (HREO) including 27 tonne/a of Y2O3, plus 6 tonne/a of Sc2O3 are in the raffinate of every uranium mill for potential recovery. Since the HREEs are already in the raffinate, cost effective HREE production is promising in Saskatchewan.Selective precipitation including nutraulization, oxalate and double-salts precipitation, as well as sulfide precipitation, ion exchange (IX) and SX are commonly used technologies for the recovery and purification of REE solution. REE oxalate precipitation is an effective technology to remove Fe, Al, Ca, Si and other impurities by taking the advantages of the solubility difference between oxalates of REEs and impurities in acidic solution (Xu, 2005)."

Jan 1, 2017

By J. Nesset, F. Rosenblum, P. Spira

"Sulphide concentrates may exhibit self-heating to various degrees during storage or shipping, the worst cases presenting a serious hazard from fire and SO2 emission. Based on measurements of heating rates on a wide variety of concentrate samples in a special apparatus, combined with field experience, a methodology has been developed which allows concentrates to be rated for their heating potential. This has proven to be very useful in practice, for example, in deciding on the need to take preventive measures. Oxidation under ambient conditions in the presence of moisture initiates heating locally within a stockpile. In the case of highly active materials, such as those that contain abundant pyrrhotite, heating may progress through three stages to temperatures well above 5000C. However, most concentrates show little or no propensity to selfheat. Heating rates were used to estimate values of the heat output, or self-heating capacity (in joules per gram), which sustains the process at each stage. Thermal data from differential scanning calorimetry are also reported. Variables which affect self-heating are discussed and an actual case of heating control on a stockpile by covering is described. A simple apparatus which can be used to simulate stockpiling conditions has been tested successfully and is proposed as a convenient test system.INTRODUCTIONPrevious publications from this laboratory on the evaluation of self-heating in sulphides dealt with tailings backfill (Rosenblum et al. 1982) and waste rock (Rosenblum and Spira 1995). Sulphide concentrates may likewise exhibit self-heating in storage or during shipping. In a comprehensive but dated review, Kirshenbaum (1 968) pointed out the conflicting nature of information on means of controlling the problem, particularly with regard to the application of water and ventilation. Modelling by Simpson (1 97 1) of autogenous heating in stockpiled zinclead concentrate and associated field measurements by Wright et al. (1972) showed that the supply of oxygen by wind and the shape of the piles were the major factors in the development of hot spots. Simpson did not attempt to explain the complex mechanism of self-heating, simply ascribing its onset to oxidation. Pearse (1 980) investigated a potential method of testing for selfheating which consisted of (i) reaction with hydrogen peroxide and (ii) differential thermal anal sis, to characterize the response of concentrates at both ambient and temperatures above 100 C. He found the method sensitive enough to identify the need for careful handling but not to predict ignition. He recommended compacting concentrates and covering stockpiles with plastic sheeting to prevent ingress of air. All these workers recognized the key role played by oxygen and moisture in triggering self-heating."

Jan 1, 2001

By B. M. Coombes

The McCracken and Stacey (1989) method of assessing geotechnical risk for largediameter raisebored shafts has been the basis for most Australian pre-construction raisebore investigations for the past 20 years. At the time of its publication, the McCracken and Stacey (M&S) Method did not include a database of raisebore diameter and rock mass conditions versus actual performance. It did, however, provide a chart that quantified geotechnical risk in terms of proposed shaft diameter and the raisebore rock quality index, QR. Two parameters, RQD/Jn and Jr/Ja were identified as being critical to raisebore stability, but the contribution of these to overall raisebore stability was not quantified. Peck and Lee (2008) published a database of raisebore performance from Australian case histories. Raisebore diameter and ground conditions, in terms of a Lower Bound QR value, were presented for 50 cases versus raisebore performance. This paper updates the database with further case histories and corrected SRF values. This paper further evaluates the reasons for the variable raisebore performance for similar RSR values. For all case histories, three parameters, RQD/Jn, Jr/Ja and Jw/SRF are investigated to assess their influence on raisebore performance.

May 1, 2011

Background Chronology 2008 Positions May 8, 2010 Summit Going Forward Say one thing and do another ??Genuine passion to see our customers succeed?, ?A passion for exceeding our customer?s expectations? Self serving actions to gain competitive advantage at the expense of the customer No single supplier or technology can manage the overall mine and its integrated operation - April 2005: Informal meeting at Toronto CIM 2004 -Unanimous interest - July 2005: Formal Calgary Meeting, developed: - Scope and vision statement , - OEM/OTM communication plan, - industry communication plan - Aug?Nov 2005: Aligned with SMART - Nov 2005?May 2006: Direct OEM, OTM communication - May ?Sept 2006: Developed baseline standards - Sept -April 2007: Developed SMART document - Sept 2007: Document distribution and request OEM OTM response - Jan ?May 2008: Acquired OEM OTM feedback and positions May 2008: Results presented to SMART and discussions on next steps

May 1, 2010

By Larry A. Morris

The environmental impacts of industrial activities have become very serious concerns of the public over the past few decades. Not surprisingly, governments have responded with legislation and regulations to force industry to operate in a more environmentally responsible manner and, more recently, have prompted industry to initiate voluntary measures in response to specific environmental issues. The concept of Product Stewardship has evolved as a system or vehicle for the industrial sector to demonstrate an active concern about the environmental impact of their products, services and processes.

Jan 1, 1996

By Larry A. Morris

The environmental impacts of industrial activities have become very serious concerns of the public over the past few decades. Not surprisingly, governments have responded with legislation and regulations to force industry to operate in a more environmentally responsible manner and, more recently, have prompted industry to initiate voluntary measures in response to specific environmental issues. The concept of Product Stewardship has evolved as a system or vehicle for the industrial sector to demonstrate an active concern about the environmental impact of their products, services and processes.

Jan 1, 1996

By Christoph Mueller

Broad band mine communication traditionally is characterized mainly by individual solutions, which have in common their long development phases and their high cost for development, operation and service. The use of Ethernet and the TCP/IP family of standardized protocols provide an uniquely price efficient combination of high bandwidth open networking, universal use and accessibility of price efficient development tools, especially because it forms the technical infrastructure for the worldwide Internet. TCP/IP and Ethernet assures reliable networking however it is not able to guarantee the latency timing of forwarding network information. Therefore, the network design requires strict load limitation and application level traffic control especially if moving equipment has to be manually remotely controlled via the network. The paper discusses the technologies the application of Ethernet and WLAN in underground mining environments.

May 1, 2006

By Francis Wm. Gray

The preparation of a paper read before this Society in 1927 on Undersea Mining led to representations to the Deputy Minister of Mines at Ottawa, Dr. Chas. Camsell, and to the Director of the Geological Survey and the Director of the Mines Branch, which resulted in the undertaking by these bodies of a geological, physical, and chemical survey of the Sydney coalfield, combined with revision of the geological maps, on all of which much progress has been made. Preliminary studies revealed the necessity for a new base-map on a scale that would permit the representation of the whole coalfield from cape Dauphin to Mira bay on one sheet, and in the making of this map the Geodetic and Topographical Surveys have collaborated, with the assistance of airplane surveys for filling-in of detail. The new map will show all the data accumulated by 50 years of active mining and will show also the extent of mine workings, with level-contours under the sea. Dr. W. A. Bell, of the Geological Survey, has, over a number of seasons, studied in the field the historical geology with the purpose of elucidating the sequence of earth movements that have determined the structure of the coalfields, especially those that have governed the course and extent of the complementary folds that traverse the Sydney coalfield. Dr. B. R. MacKay, of the Survey, and the officers of the Fuel Testing Laboratories at Ottawa have made exhaustive studies of the Phalen seam, chemical and microscopic, intended to elucidate the conditions under which this seam was deposited, and some very interesting conclusions have been reached.

Jan 1, 1934

By R. J. Chase, C. Davies

"Abstract- The Merelani graphite-tanzanite deposit is located in northeast Tanzania, 14 kilometers south of Kilirnajaro International Airport and in close proximity to the towns of Moshi and Arusha . The graphite mineralization is hosted by relatively undeformed linear Proterowic metasedimentary gneisses, several of which have been subjected to hydrothermal alteration resulting in tanzanite mineralization. Exploration work comprised detailed geological mapping coupled with pit and trench channel sampling and a subsequent 1500 meters of diamond drilling. In addition, metallurgical tests have shown the graphite to be of unusually coarse flake size, crystallinity and high purity.Feasibility studies have shown the economic viability of a major coarse flake graphite deposit with the measured resource to 50 meters in excess of 9 million tonnes assaying over 8o/o graphitic carbon . Production is due to start by the end of the first quarter of 1994 with the processing plant design capacity initially set at 15 000 tonnes per annum.ln addition to graphite production, tanzanite will be produced through selective mining within the graphite open pit in the upper horizon and from underground workings within the lower horizon.The Merelani graphite-tanzanite deposit will be the first major orebody to be exploited through means of private funding since Tanzania gained independence."

Jan 1, 1994

By Brian Hart, Stamen Dimov

"The Time of Flight Secondary Ion Mass Spectrometer (ToF-SIMS) is unique in that it measures the outermost atomic layers of any material. The technique is particularly suited for determining surface chemical composition of mineral particles. It is most commonly used as a diagnostic tool to measure mineral surface chemical variability in plant and bench top flotation separation processes. Recently, research towards understanding the full capability of the instrument has resulted in the development of new diagnostic applications related to various Au extraction technologies and the development of the ToF-SIMS as a predictive tool for assessing the chemical reactivity of the ore.In this paper we will present a brief review of the ToF-SIMS technique with recent advances in instrumentation and methodologies including:•,?recent developments and advances towards a semi-quantitative approach to the evaluation of mineral surface modifiers (ex. Cu),•,?flotation case studies investigating activator, depressant and collector loading variability within a flotation process,•,?the recently developed chemical reactivity test which we believe has the potential to predict the behaviour of minerals in a flotation test in response to chemical transfer during grinding,•,recent applications for determination of surface Au preg-robbed in carbonaceous materials.A portion of this material has been recently presented at the COM 2009 meeting and at SIMS XVII (see Dimov et al 2009 and Hart et al, 2009).INTRODUCTIONIn flotation seperation surface chemistry is the principal determinant for selective separation of the various mineral phases (Ralston, 1994, Smart et al, 2003). Determination of this hydrophobic/hydrophilic balance by particle therefore requires correct identification and selection of the particular mineral phase(s) followed by a statistical analysis of the surface chemical characteristics of the particles with an estimation of the spread of values (Smart et al, 2003)."

Jan 1, 2010

By B. W. Raymond, D. W. Zandee

"IntroductionCoal deposits are found in many regions in Canada and vary widely in their age, quality and rank. All classifications of coal except anthracite are found in significant quantities in this country.Deposits in the Maritimes are mainly bituminous; Lignite is found in Saskatchewan and Ontario and sub-bituminous coal in the plains region of Alberta. The Rocky Mountain coalfields of Alberta and British Columbia contain low and high-volatile bituminous coal and, in a few places, semi-anthracite. The British Columbia interior contains deposits of semi-anthracite, bituminous, sub-bituminous coals and lignite. The Yukon and Northwest Territories also contain substantial deposits of bituminous coal and lignite.Currently Nova Scotia produces both thermal and metallurgical coal, Saskatchewan produces lignite and Alberta produces both sub-bituminous and bituminous coal for thermal purposes. Large deposits of metallurgical coal are now being exploited in the Rockies arefl of British Columbia and Alberta by open pit methods. The raw coal is treated in large capacity preparation plants to remove refuse and upgrade the product to a consistent metallurgical quality with respect to ash, moisture, volatile matter and coking properties.The treatment of coal involves crushing, screening and cleaning by dense medium, jigs, water-only cyclones, tables and froth flotation to produce a diverse range of coal products differing in quality and size for various end uses.The chapter on Crushing and Screening Circuits was concerned mainly with crushing of metalliferous ores to produce a concentrate of one or more valuable minerals which normally constitute a small portion of the original mass of the material treated.Coal differs physically from ores in many ways such as lower specific gravity, relatively large volumes but low tonnage of product, and its habit of absorbing moisture requires extensive dewatering processes more complicated than settlement and filtration. Most significant, for this paper at least, is the fact that crushing coal is not as energy intensive and much smaller equipment is applicable.Crushing and screening of ores is intended to reduce the size of all constituents as quickly and efficiently as possible to allow liberation of the mineral particles. The crushing of coal is different in that the coal is not the minor constituent and the production of fines, in the initial stages at least, is highly undesirable. The basic objectives of crushing coal are the reduction of run-of-mine material to sizes suitable for cleaning or further reduction of coal to market sizes."

Jan 1, 1989

By J. D. Clucas, D. B. Dreisinger

"The Starved Acid Leach Technology (SALT) has been developed by Search Minerals to extract nickel and cobalt VALUES (from nickel laterite ores (saprolites) and Caron plant residues. The technology consists of sulfuric acid atmospheric leaching of the ores or residues followed by neutralization and recovery of nickel and cobalt. The acid addition is carefully controlled to maximize nickel and cobalt extraction while minimizing overall consumption of acid by various gangue reactions. The final recovery processes can be tailored for maximum economic benefit. The use of resin-in-pulp processing is advocated as the most cost effective method for initial recovery of nickel and cobalt from lower grade materials. INTRODUCTIONCommercial processes for laterite ore treatment vary according to laterite type and local conditions. The two general categories of laterite ore are saprolites and limonites.Saprolites are generally treated by pyrometallurgical processes for reduction of nickel to matte or ferro nickel alloys. The high cost of drying, chemical reduction and electric furnace smelting requires that the saprolite grade for economic processing is of the order of 1.8% nickel or higher. There are of course large amounts of saprolite that fall below this “cut-off” grade that are not currently economic.Limonites can be treated by the Caron Process which involves drying of the ore, a reduction roast of the whole ore to reduce nickel and cobalt (and some iron) to the metallic state followed by ammonium – ammonium carbonate solution to leach nickel and cobalt. Nickel and cobalt recovery are low (70-85% for Ni and 20-50% for Co). The Caron plant tailings therefore contain high levels of unrecovered nickel and cobalt. Relatively few plants have used the Caron Process and new installations are not anticipated due to the high energy cost of drying and reduction roasting. Nevertheless, plants in Brazil (Niquelandia), Australia (Yabulu) and Cuba continue to operate.The high pressure acid leach (HPAL) process was pioneered at Moa Bay in Cuba in the 1960’s in the treatment of limonites. In the 1990’s the HPAL process was touted to revolutionize the nickel industry with low capital and operating costs for new installations. Murrin Murrin, Cawse and Bulong in Australia were started and in each case the technical difficulties of operating at extreme temperature and pressure conditions and the challenges in “ramping up” a complex hydrometallurgical facility conspired to cause these plants to fail economically. At present, Cawse and Bulong are closed and Murrin Murrin continues to operate after undergoing a financial restructuring."

Jan 1, 2012