Search Documents

By A. Eltringham

Operations downstream of mining and beneficiation are still being subjected to increasing scrutiny as highly capitalized projects have been either slow to achieve their targets or have actually failed to do so. Leaching and smelting projects have fundamentally high calls on capital and technology as reaction rates are increased and the capture and disposal of unwanted products are subjected to greater restrictions. Separating value from waste inherently becomes riskier as the purification of the desired product imposes greater demands on the process to produce benign wastes. When we superimpose on the chemistry of the project severe predictions of throughput rates, that bring in facets of manufacturing, we are introducing complexities that the records show are not handled well. This paper discusses some of the more common challenges that operators face and what methods are available and are likely to be successful in preventing the loss of value as projects are brought on-stream. This thinking needs to start much earlier and at greater intensity than our industry has normally chosen to employ.

Jan 1, 2011

By R. Luchese de Moraes, J. A. Matthews, C. Feliciano Bruzual

The role of biomass char in blast furnaces has been re-examined by scientists worldwide, as a feasible option to reduce the carbon intensity of ironmaking. This contribution makes a technical and economic analysis of the ferro gusa industry in Brazil, with the last 172 charcoal-Blast Furnaces operating in the world. A key strategic question is presented: what is the current status and future prospects of biomass use in Blast Furnaces? Findings provide significant implications to metallurgists: while ferro gusa from charcoal is regarded as carbon neutral iron with low impurities, there are limiting factors that hinder the further proliferation of charcoal-BFs: biomass generation requires vast extensions of arable land and aggregates have low production capacity. Additionally, most of the charcoal is presently generated in beehive kilns with low yields. These elements combined make charcoal-hot metal expensive in price. With respect to the future prospects of biomass, the injection of small biochar particles through the PCI rigs in BFs (here coined Bio-PCI) and iron ore sintering may offer a practical alternative to significantly reduce the CO2 emissions in the ironmaking process.

Jan 1, 2015

By Theodore H. Boggs

The battle of the gold standard is not limited to one country alone, or even to a single group of countries. It is being waged merrily in many important commercial and industrial quarters. Though it is not always a practical issue calling for immediate attention, it is none the less, quite widely, engaging the thought of bankers and other students of finance. The controversy arises, in the last analysis, because of the desire of men to secure a stable currency. There are two ways of restoring a reasonably stable currency system: (1) the re-establishment of the gold standard, or (2) the deliberate and artificial management of a paper currency. Both systems are well known. The gold standard was in use prior to the war in the principal commercial countries. A currency of inconvertible paper has been at times employed in the past in various countries; for example in Britain from 1797 to 1821, and in the United States from 1862 to 1879. The gold standard, as all are aware, implies the selection of gold as the standard of value. The unit of value is a fixed weight of gold and, so long as the standard remains unimpaired, all other means of payment are maintained at a parity with standard gold coins. And gold coins alone constitute the standard money, inasmuch as their value as bullion equals their value as coins. Under the gold standard this would not be true of any other form of money, although all other varieties of money, including bank notes, government notes and silver coins would be freely convertible into gold money. Strictly speaking, the gold standard also implies that the gold money in turn shall itself be freely convertible, through melting, into gold bullion and freely exportable.

Jan 1, 1925

By Karl J. C. Harries

"10.1. INTRODUCTIONDefinitions are a necessary part of every agreement. Their purposes are to assist the reader in reading and understanding an agreement and to attempt to avert potential confusion and, therefore, disputes. In some circumstances, they may be critical in deciding a dispute. As they are often substantive, they should not be treated lightly.It is far easier and less confusing for a reader to read “the Company” or “the Recipient” than to be faced with “the party of the First Part”, or to see the “Jones Property” than “that part of the property hereinbefore described in paragraph 1.01 hereof”. It is also advisable not to use “-ee” and “- or”, as in payee and payor.One thing must always be remembered: once a word has been defined in an agreement, it will always have the defined meaning unless the contrary is clearly indicated or is required to make sense of a provision.2 It can be confusing for a reader if commonly used words are defined in other than ordinary terms. Unique words that will stand out in the text are more likely to be recognized as having special meaning. It is also good practice to identify defined terms by capitalizing them in the text of the agreement. Boldfacing of definitions is also sometimes used for this purpose but, as boldfacing is not easily identified in handwritten revisions, it can be missed in the press of negotiations, especially when several typists are involved. Lack of consistency in identifying defined terms is not a fatal mistake, but it can create confusion, especially if the reader is new to the agreement or is reading it in a highly technical manner, such as when there is a dispute.If definitions used in the main text also apply to a schedule, they need not be included in both. Omitting them from the schedule makes the agreement look shorter, which to some people is a benefit. If definitions are not repeated, make certain that the schedule clearly indicates that words defined in the main text have the same defined meanings in the schedule3 and are clearly identified as defined words. In considering whether or not to repeat in a royalty schedule definitions appearing in the agreement proper, think of definitions as an aid and a reminder to the reader. Repeating them will help a reader, if only by saving the nuisance of remembering where to find them in the main text and constantly turning to it. All the definitions needed to read the schedule will be right there, so that the schedule is a self-contained document. Just make certain that, if you do repeat a definition, you repeat it in identical terms. If you have to change any defined term to make it fit the royalty provisions, use a different word or phrase as the defined term to warn the reader that he is dealing with a different concept.4"

Jan 1, 2003

By H. C. Cooke

THE gold mining industry, in Canada as in other countries, has passed through trying times in the past year. The strains and stresses of war have drawn away much of its man-power, both from the labour and the management. The urgent needs of the war machine have greatly curtailed the amounts of steel and explosives that can be allotted to the mines; and the loss, by enemy action, of supplies of such essential things as rubber, bids fair to reduce operations still further, if not cripple them entirely in time. And, as if these difficulties were not enough, war on the psychological front has been declared on the gold mines. Earnest supporters of the war effort, well-meaning theorists, and perhaps others whose intent is less disinterested, have all combined to clamour against the continuance of gold mining. We have been asked, what is the use of taking gold out of one hole in Canada to put it into another in Kentucky. We have been assured that gold will never again have any value, except for filling teeth. We have been repeatedly adjured to look at Germany, how well it has got along without gold. We have been told that it is unthinkable, when this nation is girding her loins for war, that labour and materials should be diverted to this useless effort. Gold miners should be diverted to the base-metal mines, where they can produce something of real value to the war effort; or to war factories; or, in fact, almost anywhere, so long as they are got out of the gold mines. And, what has made the situation even more disturbing, it has seemed as if all this clamour might be convincing governments. In fact, as you all know, the government of the United States did actually take the step of ordering its gold mines to cease operations. Fortunately, however, for Canada, the facts that no large favourable effects resulted from that action, and that, in Canada, gold mining is a much larger part of the national economy than in the United States, have caused our government, so far at least, to avoid this drastic step. In talking about this, however, let me emphasize that I have no more inside information on the subject than any of you. Like Will Rogers, all I know is what I see in the papers.

Jan 1, 1943

By George P. Demopoulos, Nima Parsi Benehkohal, Marianna Uceda

Lithium-ion batteries (LIBs) find wide range of applications from portable electronics to electric cars and stationary storage or renewable energy. LIB electrode fabrication is done through mixing the active material (Li-ion host) with carbon (conductive component) and polyvinylidene fluoride (PVDF), which acts as a binder. These components are dissolved in N-methyl-2-pyrrolidone (NMP) to form a paste which is then doctor bladed onto the aluminum current collector. NMP is a toxic chemical and the overall fabrication process remains costly. Efforts are made of eliminating NMP by (1) replacing the binder and (2) using a new fabrication method. Of particular interest among these new methods is electrophoretic deposition (EPD). Via the application of DC potential, particles in suspension can be electrophoretically deposited on different conductive substrates in a relatively fast rate rendering EPD feasible for industrial application. A key aspect for successful application of EPD is the formulation of a stable suspension. Within the McGill HydroMET group, we explore the potential of EPD in fabricating LIB electrodes having demonstrated its effectiveness in the case of P25 nanotitania/carbon anodes. The performance of EPD fabricated TiO2/C electrodes is compared to standard PVDF-based electrodes and shown to have comparable charge capacity. This method is now being extended to other electrode materials. In this paper an introduction to the EPD method will be made and subsequently its use in fabricating LIB electrodes will be described. The performance of the fabricated batteries is evaluated via galvanostatic charging/discharging and cycling tests.

Jan 1, 2016

By R. D. Brown

"AbstractIn order to raise the enormous amounts of capital which will be essential for the development of Canada's mineral and petroleum resources, this country's resource industry must be permitted to earn an acceptable rate of return. The existing tax regime, with its high rates, complexities and misdirected incentives, presents a serious obstacle to our resource industries in their development of Canada's immense , but increasingly lean, resources. Government tax and other policies are not the only cause of the crisis now facing the resource sector in Canada, but a reformed tax system, with stable and reasonable tax burdens, is required if Canada's resources of minerals, oil and natural gas are to continue to contribute in the future, as in the past, to our national well-being.An independent task force, organized under the auspices of the Canada West Foundation, has recently completed a wide -ranging report: on the future development of Canada's mineral, oil and gas resources. This five-volume report, completed after almost two years of research and study, concludes that Canada •is facing a major crisis •in the development of our resources, It states that unless corrective action is taken now, mineral production and exports could decline drastically after 1985, at the same time that Canada would face massive bills for imported oil because of inadequate and declining production.The task force, chaired by the author of this article, has put forward recommendations for a fundamental shift in both federal and provincial policies in order that Canada's mineral reserves can be developed in the national interest. This article consists of excerpts from the summary of the task force's report."

Jan 1, 1977

By Michael P. Amsden

"THE ECSTALL CONCENTRATOR is situated adjacent to Highway 101 and the Ontario Northland Railroad, 15 miles east of Timmins, Ontario. Ore is delivered to the concentrator by rail from the mine, which is 17 miles northwest of the plant. Power and fuel are obtained from the hydro and natural gas lines which pass close to the plant site. Water is obtained from the Frederickhouse River, 6 miles east of the concentrator. The main concentrator building is a large structure 500 by 640 feet by 90 feet high and contains facilities for fine crushing, crushed ore storage, grinding, flotation, tin recovery, concentrate handling and reagent handling. Located in the same building are the machine shop, warehouse, metallurgical laboratory, pilot plant, men's change room, sample preparation area and an assay laboratory. The general concentrator layout is shown in Figure 47. Originally designed to handle 9,000 tons per day, the concentrator now treats 10,000 tons per day. Two different ore types are processed by selective flotation in three individual circuits to recover copper, lead and zinc concentrates. In 1973, another circuit was added to recover pyrite and tin concentrates from the combined zinc tailings of the three main circuits."

Jan 1, 1974

By Victor Azbe

Azbe System of Controlled Calcination To obtain good and cheap lime there are certain fundamental requirements that need to be satisfied. These are : (1) Proper combustion of fuel and steady supply of heat to the kiln. (2) Proper heat distribution in the kiln. (3) Uniform drawing of lime through the several shaft sections. (4) Complete cooling of the lime and recovery of the heat. (5) Temperature control of the hot zone by economical means. (6) Ample draft to obtain high capacity. (7) Arrangements to facilitate operation. Figure 17 shows diagrammatically one of the smaller kilns, intended for large stone. Such a kiln can be supplied with gas from a centrally located automatic gas producer, or, as shown, from an integral producer located snugly against the kiln. These producers make very good gas and have a gasification capacity of either 10 or 15 tons of coal a day. The producers have water-sealed ash pits, a rather thick fuel bed that is conducive to the making of high-CO gas, and are under forced draft. No steam is used. Clinkering is prevented by admixing some spent gas from the kiln with the air. Coal feeding is from a coal bunker through spouts into the hoppers over the producer. This is done, at proper intervals, by manual operation of slides, but it is planned to install mechanical feeders. Central mechanical gas producers have the advantage of requiring little labour, but the blowing of soot is a problem, as also is the proper distribution of the gas among several kilns. In the case of integral gas producers, soot from the centre burner is blown back into the producer to be burned, and the supply of gas to the kiln is controlled by regulation of air to the producer. In large plants, the mechanical producer may be preferable, but in small ones, the integral producer is cheaper, better, and more reliable. The kiln shown in Figure 17 is suitable for both systems of gas supply. It will be noticed that there are no side gas burners. All gas enters the kiln through the centre burner in a manner that permits any desired amount of gas to be directed to any of the kiln sections by the aid of regulating slides.

Jan 1, 1946

By Enzo Palumbo, Joël P. T. Kapusta, François Larouche

In light of the rapid deployment of bottom blowing smelting in China over the last ten years, one has to wonder why it has taken the copper industry so long to adopt ultra-high oxygen enrichment via Savard-Lee type injectors. As early as 1976, Kellogg and Henderson suggested, in their landmark paper on energy usage in the copper industry, that ‘maximum use of oxygen enrichment of process air’ was one of seven ‘energy saving features’ for copper matte smelting and converting. Yet today, shrouded injection and high oxygen enrichment has not been implemented in copper bath smelting outside China and Vietnam. In this paper, the authors explore the reasons why bath smelting processes such as the Noranda Reactor and the Teniente Converter still operate around 40% oxygen enrichment, while the bottom blowing SKS/BBS process typically runs at 65 to 75% oxygen, with all three processes producing white metal. Are there fundamental metallurgical explanations for this striking difference beyond the long-standing skepticism towards high oxygen shrouded injection and its perceived high implementation cost?

Jan 1, 2015

By L. D. Smith

Net Present Value Impact of Discount Rate The Discounted Cash Flow (DCF) method of valuations is universally used and accepted. The main criticism of the method is that it does not recognize the value of projects long life projects. This can be seen in the preceding graph where the present value of cash flows in later years are small for discount rates over about 10%. This graph covers a project that has a 25 year operating life. It is clear from the low height of the NPV bars at 10% and 15% in the last years of the project that an additional 25 years would add almost no value to total project NPV. As an example of this effect, an colleague undertook the evaluation of a pulp and paper project. The plant could be justified, but it was not possible to justify planting the trees as they took too long to grow and so had not appreciable NPV. The plant had to purchase wood to feed the plant.

May 1, 2013

By J. S. Vanderploeg

I WILL begin this presentation by citing the annual per capita use of copper in Canada. This is best calculated by taking refinery domestic sales, plus imports of the products of foreign fabricating mills (very little refinery copper is imported), and deducting the exports of Canadian mills. No attempt has been made to estimate the copper content of imports or exports of machinery, motors, etc., but the trade balance here is probably against Canada. In any event, we find that, though varying somewhat since the war, the estimated yearly per capita figure has reached a high of 18 pounds. This is practically on a par with the United States. The rest of the world uses an average of about 2 pounds per capita, yearly, though this includes some countries, such as Sweden, Germany and England, which consume much better than average quantities. It looks, therefore, as if the Canadian copper industry has not (as has been generally charged) been asleep after all.

Jan 1, 1962

By Henry F. Hebley

THE solid fuel industry, especially that branch represented by bituminous coal, is gradually becoming aware of its ? paramount importance in a world where there is an ever increasing demand for the products of a mechanical age. In practically every process of manufacture, the necessity for energy in some form is being multiplied. Some of that prime energy is derived from water power-hydro-electric schemes, flood control schemes, etc. - but often the electrical energy thus developed is generated at great distances from the load centres, requiring long transmission lines with consequent transformer and transmission losses. A few plants have harnessed the tidal power of the seas and one has harnessed the energy of the wind in a modern manner. All of these schemes are dependent on certain natural geographical, hydrographical, and physical advantages of terrain, as well as an adequate area of consumption of the energy developed. If flood control is the primary object, then power generation is a by-product; and the economics of large capital expenditure on power generating equipment must be considered in that light.

Jan 1, 1945

By A. Panteleyev, C. S. Ney, R. J. Cathro, A. Sutherland Brown

The general distribution of metal deposits in the Canadian Cordillera can be related to its tectonic evolution. The Canadian Cordillera is naturally divisible into five longitudinal tectonic belts within which rocks are broadly similar in type, age and history. From west to east they are the Insular, Coast Crystalline, Intermontane, Omineca and Eastern Marginal belts. Seven classes of metal deposits in the Canadian Cordillera are defined and their characteristics described. These classes are skarn, porphyry, massive sulphide, stratiform, magmatic, copper in basic lavas, and vein deposits. Maps showing the distribution of medal and metal-group concentrations serve to illustrate the relations in space and time between mineralization and geologic evolution.

Jan 1, 1971

By A. H. Burns

"Regenerative and recuperative burner systems require advanced combustion techniques to minimize NOx emissions. Various methods of pollutant minimization and furnace design considerations are described. Cited examples are a large high temperature furnace and a small Zinc vaporizing furnace. The concept of total carbon footprint is introduced. The application of Biomass combustion as an effective method of cost and green-house gas (GHG) reduction is discussed. Practical considerations of scale, location and process limitations are discussed. Two examples of biomass fired equipment are cited. Ideal sites have large biomass resources available locally. Processed biomass fuels will be an important substitute for fossil fuel. INTRODUCTIONIn 1992, I presented a paper entitled Combustion Strategies In The Modern Industrial Environment (1992). At that time an abundant supply of cheap fossil fuel made many of the measures I talked about difficult to justify for anything but new equipment.Since 1992 we, as a society, have demonstrated an ability to accelerate the pace of industrial and societal change. The term industrial revolution applied to this age of incessant change is completely meaningless, implying a discrete moment in historical time. What our society has built is a system capable of unfettered, continuous and accelerating technological change. With this change comes an increasing demand for energy and materials.This year is the anniversary of the Titanic disaster, a moment in time when technological certainty met the caprice of nature and gave us a brutal reminder of what can happen to us if we underestimate that power (Mowbray, 1912). In the intervening interval we have regained the technological arrogance that was lost in 1912 bringing us back to the problems of climate change and the need for sustainable industrial activities.We use advanced mathematics to describe many complex systems, sometimes with disastrous results. For example there has been a recent attempt to model the global economy as a completely deterministic system. This premise is flawed at its foundation as human nature and emotion are indeterminate constants in the equations, yielding probabilistic solutions at best. As engineers we are all familiar with stiff problems. The solution to such a problem is meaningless and we have all had the misfortune to live through and rue the effects of that miscalculation over the last few years."

Jan 1, 2012

By B. M. Monaghan

"The developments of the 1950s and 1960s have seen Canada become an international source of iron ore, trading in all geographical areas and hemispheres. Canada's production will significantly increase in the next decade. However, although the outlook is bright, iron ore producers cannot be complacent. Instead, we must weigh the factors that have brought about the development of the Canadian iron ore industry and examine the probable changes for the next decade that will affect its growth.Looking ahead in the 1970s, competition will be severe. Pressure on prices will continue as new sources of supply bid for long-term contracts and as steel producers continue to develop mines around the world. Rising costs will make these pressures more severe. We must balance the growth of the world's steel makers with the emergence of new supplies of iron ore. The iron ore industry is now part of a new era in which demand and supply are intermeshed, and the developments around the world are acting on the Canadian iron ore industry's future."

Jan 1, 1971

By R. J. Goodman, P. Lafleur

This paper presents a current interpretation and projections of recent statistics on raw materials availability based on familiarity with the Canadian steel industry and its development. Problems and opportunities are recognized and discussed.

Jan 1, 1976

By R. Lowery

TODAY, man uses, at will, the land, the water, and the air to transport himself and his goods everywhere across the face of the world. He no longer thinks with wonder of the magic of conquering these elements - he takes his mastery of them for granted. He is, however, constantly striving to squeeze more and more efficiency from each mode of transport. Man's first method of transporting himself and his goods was, obviously, himself; then he acquired his first beast of burden - woman. Most other two-legged female animals carried their young around clinging to their fur. Human mothers were, generally speaking, furless and their offspring less 'Prehensile, and so slings and other trappings were invented to carry young children. Man's inventive genius soon adopted these devices for carrying other burdens, and for countless centuries woman carried all in order that man could walk unencumbered except by his weapons. Later other ?beasts of burden were trained and used, including dogs, horses, oxen, camels, etc. Man also discovered quite early that he could drag along the ground more than he could carry on his back.

Jan 1, 1956

By P. A. Riveros, J. Binvignat, V. M. McNamara, D. Koren

The recovery of cyanide from a gold mill solution containing high levels of copper (400 mg/L to 900 mg/L) using the AVR process was evaluated. It was determined that acidification to pH 2 to 3 provides a suitable balance between HCN generation, copper precipitation and acid consumption. A short pilot plant campaign showed that ~75% of the feed WAD cyanide was recovered while the remainder precipitated along with copper upon acidification. The acid consumption averaged 3.5 g H2SO4 per litre of solution. The copper precipitate, consisting mostly of CuCN and CuSCN, was readily separated from the solution by gravity. The volatilization of HCN in countercurrent packed columns averaged 98.7% efficiency. Reabsorption of HCN was practically 100% in NaOH solutions and slightly lower in a lime slurry. Basic volatilizer design parameters applicable to a large-scale operation were determined, including the Henry’s Law constant and the mass transfer coefficient of HCN gas.

Jan 1, 1998

By A. Fawcett, B. C. Dyer

Abstract - The basis of the tomographic velocity imaging technique is briefly described and an application of the method to detect and image a cross-section through a chromite pod is presented. Using the chromite application as an example, the relative costs of tomographic data acquisition and processing are compared with those of diamond drilling to obtain similar resolution. A number of different tomographic survey configurations and the potential role of the method in surface and underground exploration are discussed.

Jan 1, 1994