Search Documents

By O. Engler, J. Friis, S. J. Andersen, C. D. Marioara, Y. Aruga

"This work investigates the early stages of precipitation in Al-Mg-Si alloys using a combination of high angle annular dark field scanning transmission electron microscopy (HAADF-STEM), selected area electron diffraction (SAED) and density functional theory (DFT) calculations. Quenching from a high temperature (solution) treatment leaves an alloy in a high-energy unstable state, with solute and vacancies in supersaturation. Thus, already at room temperature (RT) a large driving force exists for solute atoms to cluster and order on the Al matrix positions. DFT calculations indicate that strain alleviation is important at this stage. We observe larger regions of Mg-dominated L10 ordering together with a Si-dominated ordering of smaller clusters in a particular geometry connected to the Si-network found in all the precipitates. In addition, building blocks of the main hardening phase ?'', stabilized by vacancies, are observed at higher, typical pre-aging temperatures.INTRODUCTION Al-Mg-Si (6xxx) alloys are widely used in industry due to a combination of favorable properties such as strength, ductility, corrosion resistance and lightweight. They undergo a complex production route, usually consisting of the following thermo-mechanical steps: casting, homogenization, extrusion or rolling, solution heat treatment (SHT) and artificial aging (AA). The SHT takes place at temperatures above the solvus line in the phase diagram, usually between 500°C and 570°C, followed by a rapid cooling to RT. This ensures that high amounts of solute atoms, uniformly distributed on the cubic face-centered (FCC) Al lattice, together with a large amount of vacancies, are quenched-in. The material is therefore in a super-saturated and unstable state. During the subsequent AA, at temperatures usually between 150°C and 220°C, the solute atoms diffuse and cluster, forming metastable precipitates with needle/ lath/ rod morphologies having the main growth direction along <100>Al. With a maximum alloy solute level (Mg + Si) of only 2%, these precipitates increase material strength up to three times that of pure Al, and are essential for the final material properties. To understand and make better use of this phenomenon, it is imperative to research the nature of the precipitates (such as their atomic structure), measure their key parameters (number density, size, volume fraction) and connect it to material properties (Marioara, Andersen, Zandbergen & Holmestad, 2005; Marioara et al., 2014). The following precipitation sequence is given for the Al-Mg-Si system:"

Jan 1, 2018

By Stephen L. Chryssoulis, Stamen Dimov

"Preg-robbing has been known for many years, where increased losses are suffered because dissolved gold is removed from solution by adsorption onto carbonaceous matter. In direct cyanidation circuits it is reasonable to conclude that the preg-robbed gold is either in a gold cyanide [Au(CN) - 2, AuCN] or metallic [Au°] form. However, in circuits with a pre-oxidation step possibilities increase and multiply even further because of water recycle streams containing apparent and not-so-apparent gold ligands. It is in these circuits where speciation of sorbed gold, i.e. the identification of the gold compound, is useful. The importance arises from the fact that proper identification of the sorbed gold species can be used to determine how, when, where and why gold was removed from solution, thereby identifying the exact cause of the problem and providing clues as to how it may be rectified.INTRODUCTIONTo the best of our knowledge, this is the first attempt ever to speciate gold preg-robbed by carbonaceous matter using a surface sensitive microbeam technique. This approach enables the direct determination of gold species sorbed on carbonaceous particulates, opening an entirely new field in the understanding of the chemistry of gold sorption on carbon. The reasoning behind this effort was to add to the current knowledge of the detrimental effect chloride ions have on gold recovery by the pressure oxidation and in particular why in the ensuing CIL step, gold is not being desorbed from the surface of the carbonaceous particles (Table 1)."

Jan 1, 2004

By A. Boeing

Rock-breaker automation and remote operation improves the safety and efficiency of mining operations. This article presents an overview of the Rocklogic rock-breaker automation system architecture that provides collision avoidance, automated parking, and remote operation functionality. The system consists of a distributed computer control system that interfaces with sensors attached to the rock-breaker, the rock-breaker hydraulics, and the site infrastructure. We present results of an automated Transmin rockbreaker installed in a production environment at an underground Australian mine site. The system has been in production use for over 900 days during which there have been no reported collisions, and 100% adoption of the remote operation technology. As a result, Rocklogic has significantly improved the safety of rock-breaking operations and reduced the rock-breaking cycle time, thereby improving the sites overall throughput.

Aug 1, 2013

By E. Yan, M. Mankosa, E. Wasmund

"Rougher flotation in sulfide ore applications is typically performed using conventional flotation machines. The trend over the last 100 years has been for these cells to become larger in volume with cells reaching sizes of 600 m3 and in some cases even larger. The associated foundation loadings, transport and installation requirements along with building size have also increased. In an economic environment where projects must be executed with dwindling capital supply, bigger is not always better. More recently, industry is being challenged to identify new technology that allows for improved flowsheets and financial returns through efficiency gains. To meet this challenge, a novel high-intensity two-stage flotation system known as the StackCell™ was tested to potentially achieve installation volume and required retention time gains when compared to conventional flotation circuits. The results from on-site pilot scale work conducted on typical copper concentrator rougher flotation feed showed retention time gains on the order of 6 to 9 times when compared with conventional flotation equipment. This finding has the potential of reducing capital demands for rougher flotation circuit designs when incorporating the StackCell. The results from test work will be discussed in this paper showing comparative test data generated with a Denver bench batch test, pilot StackCell and large conventional cells, all receiving the same feed.INTRODUCTION Over the last few years, a number of flotation devices have been described as two-stage or multi-stage flotation units. The idea behind multi-stage flotation devices is that flotation performance can be improved by utilizing cells with multiple specialized units in series, but not all units of the same type, as is practiced in trains of multiple tank cells or columns. Instead, each unit is specially designed to provide the optimized fluid environment for each stage of the sequential flotation process. This idea has been proposed based on a study of the fundamentals of the flotation process, and the realization that the process consists of discrete sequential processes, that are each optimized with dissimilar process conditions (Finch et al, 1995), (Zhou, 1996). Instead of executing each step simultaneously in a homogeneous fluid environment, where the conditions would be a compromise between particle collection and froth recovery, the multi-stage flotation unit operates in a set of segregated process environments, each with a set of conditions optimized for that step."

Jan 1, 2018

By G. S. Farnham

Abstract This paper lists the interests of the Physical Metallurgy and Chemical Research laboratories of the Metallgesellschaft, which were visited by the authors, members of a group of Canadian investigators sent to Germany by the Department of Reconstruction in 1945. The Physical Metallurgy Research Laboratory The following information was obtained from Professor E. Schmid, Chief of the laboratories. It is understood that Dr. Schmid is a former Nazi and was to be removed from his post in November (1945). Aluminium Research The laboratories investigated the corrosion resistance of the high-strength aluminium-magnesium-zinc alloys. The same test procedure as used by V.L.W. was followed and Dr. Schmid co-operated closely with Dr. Brenner on this project. Intercrystalline corrosion was combatted by additions of chromium, titanium, or vanadium, and the work in this field parallels that of Dr. Brenner of V.L.W. * Dr. Schmid reports that Bollenrath and Siebert believe that corrosion difficulties with these alloys can be overcome to some extent by heat treatment. He himself was of opinion that the correct answer lay not only in correct alloying but also in correct heat treatment. The heat treatment involved either interrupted quenching or a change in quenching rate from a solution temperature of 500°C. The procedure is either a slower cooling from solution temperature or an interrupted cooling with a holding period at l50°C. Work had been done on piston alloys, the 11-13% Si, 1% Ni, 1% Cu, and 1% Mg being the favoured material. This is called Lo-Ex and is similar to Mahle 124 or KS1275.

Jan 1, 1946

By L. Hanschar, C. Bwalya, E. Mokola, K. Musonda, A. Makayi

This paper describes the installation, commissioning and operation of porous plugs featuring nitrogen gas purging in both Anode Furnaces at the Kansanshi Copper Smelter (KCS), a greenfield copper smelter which commenced operation in March 2015. The decision to install porous plugs was taken in November 2016 and the facilities were successfully commissioned on both anode furnaces in October 2017. The project was successful and has demonstrated the following process improvements: 12.2% reduction in main burner fuel consumption Larger average charge size, due to fewer accretions; 17 minute decrease in average refining cycle times Improvements in slag skimming operations Improved casting rates INTRODUCTION Porous plugs The application of porous plug technology in copper smelter anode furnaces is well established around the world. Vukovic and Gamweger (2017) and Wallner (2004) noted that the stirring and mixing action induced by the injection of inert nitrogen gas into the molten copper via porous plugs has potential benefits in the following areas: Homogenization of the temperature and composition of the molten copper resulting in Reduced fuel consumption Less tendency to overheat slag (reduced risk of refractory attack) Less slag produced with a lower degree of oxidation (lower rate of refractory wear) Less tendency for buildups to form Improved environmental performance (produce low sulphur blister at Peirce Smith converters) Elimination of buildups inside the furnace and potential for larger charges per cycle Reduced processing times and potential for shorter cycle times More efficient skimming of anode slag Shorter skimming time Less copper carry over to Peirce Smith converters Very little slag remaining in the furnace (reduced potential for buildups to form)

Jan 1, 2019

By R. B. STEWART

A few days ago, while reading a report of the late Dr. Robert Bell in preparation for this afternoon&apos;s meeting, I found some impressive figures concerning the magnitude of the Hudson Bay basin. From the waters of the Bay itself, this great territory extends eastward 500 miles, westward l,300 miles to the Rocky mountains, and southward to the source of the Red river. It has a width of 2,100 miles from east to west, and a length of l,500 miles from north to south. Its area is almost three million square miles. It is not, of course, my intention to review the natural resources of this vast territory, but to confine my remarks to that portion of it adjacent to the waters of Hudson bay. A number of erroneous ideas exist in the minds of many concerning this northern country, especially as regards its latitude and climate. Burwell, at the entrance of Hudson strait, is in the latitude of 60 degrees or roughly that of the north of Scotland. The southern end of James bay has about the same latitude as the northern end of Vancouver .island.

Jan 1, 1928

By J. A. Brusset

Introduction The West Canadian Collieries, Limited, operate three bituminous coal mines in the Crowsnest Pass district of Alberta. Two seams are worked; their thickness varies from 10 to 20 feet and their pitch from 10 to 45 degrees. The Bellevue mine was opened in 1903, the Greenhill in 1914; both are gassy and dusty, and at both the haulage is a problem, as the workings are spread over distances of several miles. Compressed-air locomotives are used at Bellevue, rope-haulage at Greenhill, both of which solutions of the haulage problem are costly in installation an operation, and lack flexibility. In 1943, the Adanac mine was opened; and the question soon arose as to which system of haulage should be selected. Compressed-air locomotives and ropes were rejected on the ground of high cost. Since, under the Alberta Mines Act, the use of trolley locomotives underground in coal-seams is not permitted, the choice lay between storage battery locomotives and Diesel locomotives. The preference of the author, who had had experience with both in French gassy coal mines prior to 1930, was for Diesel locomotives, due to lower cost of installation and greater flexibility and reliability. However, Regulation No. 13 of the Mines Act of Alberta reads: &apos;No gasoline-driven engines shall be used underground in any mine, and no internal combustion engine shall be used underground in any coal mine, except only when authorized by the Chief Inspector in writing, and on such terms as he may prescribe"

Jan 1, 1948

By H. J. Ni, M. Y. Huang, S. W. Chen

The effects of several fluxes on purification, microstructures and properties of A00 aluminium have been studied. The experimental results and analyses indicate that many cracks and large porosities exist in the surface film above the melt purified by C2Cl6 and that the film is floe and mostly composed of AhO3 and pure aluminum, which carries many carbon particles and AlCh not fully volatilized. And then over 50% of the all-melting residue is pure aluminum, which is one of the major reasons for high melting loss. Moreover, because of a mass of gas bubbles and a state of seethe, there exist many inclusions which size is under l0µm in the microstructure of A00 aluminum purified with C2Cl6 or fluxes containing C2Cl6- With this purifying method, the aluminum crystal grains are extended along the radius that was observed firstly and the average crystal size of A00 aluminum are about 100µm~150µm. In addition, small size inclusions have little affected on tensile strength and micro inclusions under l0µm have little affected on elongation.

Jan 1, 2006

By C. K. Wilton

"The Agnew Lake uranium deposits were discovered in 1953 following the discovery of the Elliot Lake deposits to the west. The original property was optioned to Kerr Addison Mines Limited who added additional claims by staking. Agnew Lake Mines Limited was incorporated in 1967 to develop the property and a shaft was sunk to 1040 metres and five levels developed before work was suspended due to low uranium prices at the end of1970.In 1974-75 the mine was dewatered and production started in 1977. By 1978 reserves were estimated at 10,000,000 tonnes averaging 0.35 kg. U10 , per tonne. Underground operations were terminated in 1980 although a uranium leaching operation was continued until early 1983.The deposits lie near the contact of Huronian metasediments with underlying Algoman granite. The sediments consist of arkose, conglomerate, argillite and quartzite with the uranium mineralogy mainly confined to oligomictic quartz pebble conglomerate. The higher uranium values are related to conglomerate with highest percentage of pebbles. The chief uranium minerals are uranothorite and monazite. It is of interest that the uranium thorium ratio differs appreciably from that of the Elliot Lake deposits. This fact along with the fact that the Elliot Lake sediments were deposited by paleocurrents from the northwest whereas the Agnew Lake sediments were deposited by paleocurrents from the northeast indicates widely separate sources for the deposits. It is suggested that the Agnew Lake uranium deposits are syngenetic placers deposited under anoxygenic atmospheric conditions."

Jan 1, 1986

By G. J. Arseneau

Mineral resource statements are reported as tonnage and grades. While great care is placed on generating a reliable estimation of grade, the determination of bulk density for resource estimation is often overlooked. Often mineral resource statements are prepared using a simple average value of bulk density. While a simple average estimate of bulk density can be appropriate for some deposit types, an over simplistic estimation of bulk density can result in serious errors in tonnage estimates and consequently to an over or under estimation of metal content. The construction of a reliable bulk density model requires an adequate bulk density database in order to develop a good understanding of the variability of bulk density with grade and geology. A reliable bulk density database is also essential in determining the appropriate modeling technique to minimize the errors in mineral resource statements caused by incorrect bulk density determinations. This paper summarizes bulk density measuring techniques and draws on examples from various deposit types examining the basic principles of bulk density modeling and domain construction for each deposit type. Examples are presented of simple bulk density domains and more complex grade variable bulk density domains with a discussion of best approaches for minimizing errors in density estimation.

Aug 1, 2013

By Nick D. Rose

The importance of structural geology in open pit slope stability is overlooked in many mining operations due to pressures to cut costs and minimize mine personnel. As a result, mine geology staff are often unable to keep up with geological mapping of the pit slopes due to other day to day production oriented tasks. In some instances, key structural controls that contribute to slope instability may not be identified until after a slope instability has initiated, at which time it may be difficult or impossible to delineate these features in the field. Even for small slopes, understanding the engineering and structural geology of the rock mass, as well as the effects of groundwater and blasting practices, are of key importance to slope stability. Two case histories are presented as examples of mining operations that experienced slope instability with little more than anecdotal information about the structural and groundwater conditions encountered during mining. By conducting field reconnaissance, simple slope stability analyses and ongoing slope monitoring, practical remedial measures were implemented, allowing continued safe mining operation.

May 1, 2002

By M. Wu, G. Plascencia, A. E. M. Warner, A. Vahed, T. A. Utigard

Nickel oxide granules formed by pyrohydrolysis of a chloride solution, were reduced in hydrogen. Below 400 °C, an incubation period was observed, followed by very slow reduction. In the temperature range from 400 to 600 °C, the rate of reduction increased with increasing temperature and increasing hydrogen pressure. Microscopic analysis showed that in this temperature range the reaction followed the shrinking core model. Above 600 °C, the reduction rate decreased noticeably before suddenly becoming very fast at and above 950 °C. Microscopy showed inner bands of metallization inside the outer metallic rim, indicating partial blockage of the interface between the reacted and un-reacted NiO core. At these temperatures, particle agglomeration and sintering were also found to take place. Surface segregation of sulphur may account for the slow down in reduction rate above 600 °C. From an industrial point of view, reduction should be carried out from 550 to 600 °C with as high a concentration of hydrogen as possible. If sintering and agglomeration are not of any concerns, reduction can be carried extremely fast at about 1000 °C.

Jan 1, 2005

By Richard E. J. Putman

THE MINERALS INDUSTRY has always been a heavy user of energy in most of its unit operations: power in the mining, comminution, flotation and electro-winning processes; fuel in its smelting and other metallurgical processes; and, of course, fuel in the on-site generation of power and steam. Many of the techniques for using computers to perform energy management and conservation tasks have been known for some time, but they have not been widely implemented because the return on investment has hitherto been insufficient. Recent trends, however, have not only caused the dollar return to rise due to higher purchased energy costs, but the cost of the investment to fall. One trend has been the generally lower cost of computer control systems themselves, due to vendors having adopted the newer, lower-cost and more reliable electronic component technologies now becoming universally available. The second trend is the development of low-cost, but high-speed, remote multiplexing devices, which have reduced considerably the expense of bringing data from points scattered over a wide area, which is typically the case when applying energy management systems to a minerals processing plant. By taking advantage of these and related developments, computer control systems can now have a rewarding impact on plant energy management and conservation practices, and recent advances in application technology have opened up new and additional opportunities for energy cost reduction and control.

Jan 1, 1978

By Andre Vien, Jean-François Dupont

"Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the installation and use of such a device on a SAG mill at the Holt-McDermott Mine. Comparison to measured static volumetric load and bearing pressure and inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed. INTRODUCTIONWhile the measurement of load is very important in all kinds of grinding applications, the biggest benefits are expected from AG and SAG milling. This is what motivated Holt-McDermott to take a closer look at this problem, with a view to optimizing SAG mill performance.In many cases, the SAG mill control problem can be stated as maximizing throughput while avoiding a volumetric overload, with the other constraints (e.g. power, grind size, upstream/downstream equipment constraints, etc.) playing a less important role. This is certainly true at Holt-McDermott where the SAG mill is the production bottleneck about 90% of the time, and anything that can be done to increase SAG mill throughput will have a significant impact on operating profit.Although the goal of maximizing throughput while avoiding volumetric overload is simple to state, it has proven to be much more difficult to achieve. The mineral processing industry has expended a great deal of time and effort to devise control strategies in the pursuit of this objective. While much progress has been made, there is still room for considerable improvement. Across the industry it is probably fair to say that overloads occur relatively infrequently, but the real losses accrue as a result of the tendency to run rather conservatively."

Jan 1, 2001

By F. T. Mooney

Introduction The Flin Flon mine of the Hudson Bay Mining and Smelting Company, Limited, is on the interprovincial boundary between Manitoba and Saskatchewan, about four hundred miles north of the Canada-United States boundary. The orebodies are gold, silver, zinc, and copper replacement deposits occurring as irregular lenses of massive sulphides, arranged en echelon, and irregular masses of disseminated copper sulphides in chlorite. The country rocks are of Precambrian age, dominantly lava flows. Development of the Mine The mine is opened by two vertical main shafts- the North Main and South Main shafts- 3,800 feet apart. The North Main shaft has a depth of 2,210 feet and the South Main shaft is completed for stoping operations to the 3,250-foot level (see Figure 1). These shafts are connected by main haulages driven, on the footwall side of the orebodies, at 520-foot intervals down to the 2,210-foot level. No. 3 (subsidiary) shaft is on the footwall side of the orebodies at a point between the North Main and South Main shafts, 2,400 feet south of the former. It has a depth of 3,250 feet and connects with all main haulage levels- with both Main shafts down to the 2,210-foot level and with the South Main shaft on the 2,750-, 3,000-, and 3,250-foot levels. Other openings tO the mine include B North fan raise, the opening due to the recovery of the open pit sill pillar, and several back-fill raises.

Jan 1, 1949

"The application of telerobotics to mining is currently being introduced into production systems around the world. Mining companies in Canada, Sweden, South Africa, and Australia have tended to lead the international charge to this form of technology for mining. While this introduction is taking place, a few basic questions have yet to be answered. How many machines can a single operator run? How many types of machines can a single operator run?A Canadian Research Chair in Robotics and Mine Automation has been established at Laurentian University to investigate these questions and many more through a series of experiments in a telerobotics laboratory that connects Laurentian teleoperation workstations to model mining machines at Cambrian College’s eDome. The laboratory supports many experiments allowing researchers to physically run multiple robot scenarios differing the numbers and types of machines at one quarter scale. Further experiments are being designed to investigate the potential for managing time delays in telerobotics. This paper describes the laboratory, experiments, and some preliminary results."

Jan 1, 2005

By Ye Chen, Jianhua Chen, Xianhao Long, Qingxia Liu, Zhenghe Xu

"It is crucial to understand the mechanism of the collector interacting with the mineral surface in the presence of water molecules, which could influence the relaxation and electronic properties of sulphide mineral surface due to the proximity effect for narrow band gap of semiconductors. The adsorptions of three typical collector molecules (xanthate, dithiocarbamate and dithiophosphate) on the sulphide mineral surfaces in the absence and presence of water molecule have been simulated by density-functional theory (DFT). The calculated results show that the adsorptions of collectors on clean mineral surface in vacuum are not in agreement with the observed flotation behaviours. The presence of water molecules has a great influence on the adsorption of collectors. The analysis of density of states of the mineral surface atom suggests that the adsorption of water molecules could influence the electronic properties of mineral surface and consequently influence the adsorption between the surface and the collector molecule.INTRODUCTIONIn the separation of multi-metal sulphide ores, the selectivity of a collector is a key factor for the efficient recovery of the aimed mineral. Xanthate, dithiocarbamate (DTC) and dithiophosphate (DTP) are the most common collectors used in the flotation of sulfide minerals. Generally, xanthate exhibits powerful collecting property but lack of selectivity. While dithiophosphate and dithiocarbamate show the good selectivity in the lead and copper sulphide mineral flotation. The mechanisms of these collectors interacting with the sulphide mineral had been attracted many attentions and several mechanism based on experimental results had been reported (Chander & Fuerstenau, 1974; Fuerstenau, 1990; Raju & Forsling, 1991; Crozier, 1991; Bradshaw, Cruywagen & O’Connor, 1995; Guler, Hicyilmaz, Gokagac & Emekci, 2006). However, the micro-mechanisms of the selectivity of these three thiol collectors on different sulphide mineral surfaces are not fully understood."

Jan 1, 2016

By A. J. Goodman

Introduction The position of Turner Valley in the foothills of Alberta, some thirty-five miles southwest of Calgary, is too well known to need further description. This attempt to interpret in detail the nature of the structure, and its relationship to neighbouring structures, together with general observations on the foothills belt, is based on work carried out in the office of the Supervisory Mining Engineer, at Calgary. The object in view was the correlation of the mass of evidence which had accumulated from the detailed examination of drill cuttings, and to discover, if possible, its structural significance. Unfortunately it is not possible to publish most of this detail owing to its confidential nature, and in consequence the reader is asked to accept certain statements, which under other circumstances would not be made without supporting evidence. The main argument for the general structural interpretation rests on evidence which has already been made public, and it is possible to proceed to logical conclusions on the main points. The evolution of ideas concerning the structure of Turner Valley is somewhat difficult to follow, as, compared with all that has been said on the subject, there is not a great deal on record.

Jan 1, 1930

By Jae-Chun Lee, Sadia Ilyas

We investigate the technical feasibility of bioleaching of metals from low grade sulphidic ore. Experiments were conducted with an adapted consortium of Sulfobacillus thermosulfidooxidans and Thermoplasm acidophilum in batch bioreactors (1.5 L), small columns (10 kg ore load, 8 % S0 sludge) and large columns (80 kg ore load, 12 % S0 sludge). Approximately 83 % Ni, 85 % Cu, 55 % Fe and 81 % Zn was leached out in batch mode while 93 % Ni, 89 % Zn, 81 % Cu and 65 % Fe was leached out in column reactors. Bioleaching potential improved by acid pre-leaching, adaptation of microbial consortium and periodic bleeding of effluents.

Jan 1, 2014