Search Documents

By Pierre Roy, Claude Gosselin, Maryam Sadeghi, Michel Bourassa, Christian Rochefort, Claude Bazin, Gautier Mahieu, François Lavoie, Marilène Renaud, David Cataford

"Spirals are gravity concentrators used for the concentration of iron oxide minerals from ores. This paper presents the mineral size recovery curves observed for spirals operating in two Canadian iron ore processing plants. The size recovery curves are presented for rougher, cleaner and re-cleaner spirals. The partition curves observed for the spirals are significantly different than those observed for typical gravity concentration devices such as hydrocyclones or hydraulic classifiers. The size recovery curves show the complex behaviour of the minerals as they flow down a spiral and are analysed with a view toward process modelling and simulation. Initial simulation results show that gains in the iron recovery can be achieved by increasing the recovery of coarse iron oxide particles in the rougher spirals.INTRODUCTION Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and different heavy minerals ores (Wills, 1992). The classification of the particles in spirals is based on the combination of gravity, centrifuge, drag, lift and Bagnold forces (Atasoy and Spottiswood, 1995; Burt, 1984; Bouchard, 2001). Several papers are dedicated to the analysis of the forces acting on the particles flowing down a spiral (Das and al., 2007; Sivamohan and Forssberg, 1985; Holland-Batt and Holtham, 1991; Holtham , 1992). Most of these papers aim at the development of a general model for the simulation of the classification of the particles for coal ore processing. Few papers deal with the operation of spirals for processing iron ores (Hyma and Meech, 1989; Srivastava, 2001; Dallaire et al., 1978) and fewer papers present results for spirals used as cleaners following a rougher stage. Since the classification in spiral classifiers is dependent on the particle size and specific gravity a partition or performance curve commonly applied to classifiers (Mai Manga et al., 2012) is used here to analyse spiral operation. Few papers were found to describe the operation of spirals in terms of partition curves (Atasoy and Spottiswood, 1995; Holland-Batt and Holtham, 1991; Richards et al., 2000). Most of the investigations presented the application of a model to simulate the position of coal particles of various sizes and specific gravities along the trough of a spiral (Kapur et al., 1996; Holland-Batt and Holtham, 1991). In addition most of the available literature on spirals deals with one stage of concentration by spirals (Dallaire et al., 1978; Das and al., 2007; Sivamohan and Forssberg, 1985) while industrial circuits usually consist of rougher and cleaner spirals."

Jan 1, 2014

"The characterisation of resources and description of variability across different ore domains is key to accurate prediction of probable metallurgical performance. Such characterisation testwork often has limited drill-core from which to work and this immediately confines the characterisation method to smallscale. For flotation feeds, the JKMSI (Mineral Separability Indicator) is being developed as a potential characterisation tool, building on earlier work by Chudacek, (1990), which used shaken test tubes, and was called the EMDEE device. In addition, the consistency of flotation recovery for specified size fractions has shown to be preserved, irrespective of the amount of material in that size fraction obtained by different milling conditions, so that the overall recovery can be estimated from knowing the particle size distribution (McIvor and Finch, 1991; Bazin et al, 1994, Runge, 2007 and Wightman et al, 2010) The JKMSI unit uses less than 10 g of material per test in narrowly sized classes and results to date have demonstrated the value of the test. This paper discusses the potential of the test by demonstrating the link between JKMSI performance and mineralogy of five different ores from Laguna Seca, Escondida Minera Limitada as well as the correlation to plant scale performance obtained in an earlier survey (Coleman et al, 2006). Further work to tie down the proof of representatively of the small sample has been identified and is discussed and included in the paper. INTRODUCTIONSince the uptake of the flotation process at the turn of the twentieth century, small scale, laboratory methods have been sought to characterise flotation response. Although laboratory batch flotation tests are the most widely used method to evaluate reagents, characterise ore variability and obtain suitable model parameters using various scale up factors Runge (2101) other methods using less ore would be useful where ore samples were limited.A method using test tubes for testing ores’s flotation response to reagents was first developed by Ian Walk (Wark & Wark, 1935; Wark; 1938; Sutherland and Wark 1955). In these tests a 50 cc stoppered measuring cylinder served as a means for a qualitative experiment, the aeration being effected through violent shaking by hand. In these experiments about 10 g of mineral was ground by pestle and mortar under water after which the ground material was deslimed and adequately conditioned with the appropriate reagents."

Jan 1, 2013

By Ernest Baafi

A simulation model RoadSIM using the ARENA modelling system has been developed to evaluate roadway development options for a given development panel configuration. The RoadSIM simulation system has provisions for variability/randomness in operations including cutting and loading at the face, tramming and discharge of coal to the boot end and availability of equipment. The modelling system provides a means for assessing the operational limitations of roadway development practices at a particular coalmine. It is a ?what if? tool that allows a range of equipment, configurations and operating practices to be assessed in terms of achievable advance rates and equipment utilisation. Output from the system is in the form of a dynamic visualisation as well as summary reports and detailed logs of operations over time.

Oct 1, 2009

By Robert E. McIvor

"“Classification System Efficiency (CSE)” is a powerful, emerging tool that can be used to increase grinding circuit efficiency. It is defined as the percentage of the ball mill energy being used to grind target, oversize particles. The discovery, validation and current use of CSE, including how it was manipulated, are described through seven plant case studies. These resulted in efficiency improvements ranging from 3 to 30 percent, along with major reductions in over-grinding. The achievable CSE for any given circuit is described. This paper demonstrates both how, and how much, every plant can benefit from increasing grinding circuit CSE.DEFINITIONS: BALL MILL CIRCUIT “CLASSIFICATION SYSTEM EFFICIENCY (CSE)”, “EFFECTIVE MILL GRINDING POWER”: “WASTED/OVER-GRINDING MILL POWER”The closed ball mill circuit is shown in Figure 1. The extreme importance of the circulating load ratio in determining circuit productivity was demonstrated by Davis (1925) and re-published by Guadin (1939), as shown in Figure 2. The circuit production rate increases with increased circulating load ratio, rapidly so at first and continuing to increase more gradually with higher and higher values of circulating load ratio.The underlying cause of this relationship was seen when comparing the ball mill feed and product size distributions from two different ball mill circuits, one with a low circulating load ratio, and one with a high circulating load ratio (Figure 3). While the F80’s and P80’s of these two circuits were close to the same, the mill feed and discharge size distributions were quite different. The ball mill in the circuit with the higher circulating load ratio contained a substantially greater fraction of material coarser than the target P80, as indicated by the respective mill feed and discharge size distributions. This fraction represents the fraction of the mill power being expended on “coarse” (in this case, plus P80 size) material, or the circuit “classification system efficiency.” The “effective mill grinding power” is the total mill power multiplied by the CSE. The compliment of CSE, the remaining fraction of “fines” in the mill, is the fraction of the mill power being wasted, and spent on over-grinding of material already finer than the circuit target product size. This is the “wasted/over-grinding mill power”"

Jan 1, 2013

By J. W. Hohn

The precipitation of Fe(III) to form ferrihydrite in the presence of arsenic is the United States EPA's Best Demonstrated Available Technology for treating arsenic-containing hydrometallurgical solutions and waste streams. This technology has been widely adopted throughout the world and developments have been well reviewed. The adsorption and long-term stability of ferrihydrite can be improved by co-precipitating Fe(III) and Al(III) together to form an aluminum-modified ferrihydrite. Arsenate adsorption into ferrihydrite and modified ferrihydrite as a function of pH, Fe/As or (Al+Fe)/As mole ratio, and the initial As(V) concentration is presented and compared. The results of long-term aging of both adsorbents at 70°C for over a year are also summarized.

Jan 1, 2006

By A. S. Moghaddam

The transportation of cemented and non-cemented mine tailings in the form of paste through pipelines is one of the main stages of paste backfill operations. For the purpose of pipeline design, the rheological properties of the materials, such as yield stress and viscosity must be determined. In this study, the yield stress of two Canadian mine tailings, for gold and copper mineralization, were studied using the vane method and slump tests. The comparison between the vane method and the slump tests indicates that the slump tests generally overestimate the yield stress values for both cemented and non-cemented paste backfills. In addition, the effects of 5% Portland cement (type 10) and mixing time on the yield stress of paste backfills were investigated. The percentage of cement as a binder agent has a direct effect on the increase of the yield stress of paste backfills. Yield stress measurements show that mixing times of 4 minutes and 12 minutes have the same effect on the yield stress values.

May 1, 2007

By U. Olsson, M. Ramström

"The IREDES1 Special Interest Group (SIG) for drill rigs has been active since its launch during MineExpo 2000 in Las Vegas, Nevada, United States. SIG for drill rigs is responsible for the development of an IREDES drill rig profile, including the exchange of production planning, performance, and quality reporting data between various kinds of drill rigs and the databases used by the operating mine. During 2001, a first draft of the drill rigs profile was jointly prepared by drill rig suppliers, mining companies, and third-party suppliers and reviewed during several SIG meetings. The profile for prototyping projects was released in mid-2002; the first official IREDES release was based on feedback received from these projects.In 2002, LKAB and Atlas Copco decided to carry out an IREDES prototyping project using the Simba L6C production drill rig. The goal was to verify the drill rig profile and identify potential problems prior to the official release. This was done by implementing the IREDES prototype version into LKAB’s production planning and Simba rig control systems. The Simba rig control system was designed to handle drill plan and logging information coming from the mine planning system. In parallel to this, the mine production system was adapted for drill plan export and logging data import in IREDES format.This paper presents the most recent results of the IREDES prototyping project. Results from late 2002 show that the basic architecture of the drill rig profile works and that a common language for data exchange, IREDES, will be a central requirement for future mine automation.As a result of the IREDES prototyping project, the IREDES standard was approved at the IREDES board meeting held at the 2003 CIM Annual Conference and Exhibition. Soon thereafter, IREDES compliant products, including drill rigs and mine production planning systems, were put on the market."

Jan 1, 2005

By X. -G. Chen, E. M. Elgallad

Direct chill (DC) cast ingot plates of 2xxx alloys have been increasingly used for large mold applications in the plastics and automotive industries. A novel heat treatment practice for Al-3%Cu-1%Mg DC cast ingot plates has been developed, involving solution treatment, furnace cooling to the desired aging temperature and holding for appropriate time at the aging temperature. The mechanical properties of the plates were studied for different combinations of aging temperature and time, using hardness measurements and tensile testing. The evolution of the strengthening precipitates was investigated under different cooling rates corresponding to cold water quenching, still-air cooling and furnace cooling, using electrical conductivity measurements. The results showed that by applying the novel heat treatment, the cast ingot plates could provide a wide range of combinations of strength and ductility satisfying the design specifications of large molds. This, in turn, offers a practical solution for the fabrication of extremely large DC cast plates combining between good mechanical properties and low levels of residual stress using the shortest possible heat treating cycle.

Jan 1, 2015

By D. R. Tesarik

Researchers from the National Institute for Occupational Safety and Health (NIOSH)1 and engineers from Placer Dome, Inc.2, conducted an underground rockfill span test at the Turquoise Ridge Mine near Golconda, Nevada, USA with the purpose of improving safety and increasing productivity by using a bulk mining method instead of drift and fill. A rockfill sill was constructed by mining and backfilling six adjacent, parallel drifts and then undercutting the sill with a 13.7 m (45 ft) wide and 30.5 m (100 ft) long room. Displacement measurements from vertical borehole extensometers installed in the mine roof and rockfill indicated that the sill remained stable with a maximum vertical deformation of less than 5 mm (0.2 in). These results were confirmed by visual observations and calculations from a validated three-dimensional numeric model of the sill. The numeric model was also used to simulate load on the sill produced by dislodged roof material in the shape of a 11.0 m- (36 ft-) high triangular prism with base measurements equal to those of the sill. Failure in the bottom third of the sill occurred with this additional load.

May 1, 2007

By G. A. Kosick, C. A. Harris

"Metallurgy at the Polaris Mine is approaching an impasse, with lead and zinc concentrate grades and recoveries approaching their theoretical maximums. In an effort to increase productivity, plant throughput and operating material costs became a major focus of milling personnel.one method of increasing plant throughput was to minimize flotation circuit upsets by; standardizing operating strategy, decreasing control action response time of operators, increasing training of operators, and providing a more available decision support system for operators.To achieve these goals, Polaris personnel decided to utilize expert system technology to develop a real-time process controller for the flotation circuit which would be capable of justifying its actions to operating personnel.This paper describes the procedures followed in constructing the first process controller in the mineral industry which is based on the principles of Artificial Intelligence.IntroductionThe Polaris Concentrator was constructed in 1980 on a barge in Trois Rivieres, Quebec and towed to its present location on Little Cornwallis Island, North West Territories, about 1450 kilometers from the North Pole. The plant presently treats about 2,800 MTPD of new feed with average feed grades of 3% Pb, 13% Zn and 5% Fe. Current production averages 36,000 tonnes of lead concentrate and 220,000 tonnes of zinc concentrate annually.In an effort to increase the efficiency of the concentrator, the decision was made to implement an innovative control system on the flotation circuit. This system would embody and utilize heuristics ""rules-of-thumb"" gained from operators to make on-line process decisions. It would also justify these decisions on a demand basis."

Jan 1, 1988

By Y. Faitakis

In the mining industry, maintenance is a key priority and a major expense. As mining equipment is large in scale, high in cost, and difficult to tow, it is key to maintain equipment on a timely basis. Breakdown in -40°C or away from a maintenance station can cause great costs in repair as well as lost production. It has often been quoted that about 5% of the North American production is lost every year due to unscheduled downtime. About one-third of the downtime is attributable to equipment failures. From this fact alone, it is evident that proper equipment maintenance can add tremendous value to the bottom line. As organizations and equipment become more sophisticated, maintenance expectations begin to evolve. This evolution can be traced through three generations: The first generation (1940?1950): A ?fix it when it broke? attitude prevailed during that time, mostly because the industry was not highly automated. The second generation (1950?1980): Automation and mechanization of the industry increased. The industry now was dependent on machines performing the majority of the work. Preventive maintenance (overhauls at fixed intervals) appeared as the first maintenance practice. Maintenance costs started to rise rapidly. The third generation (1980?): Assets become more complex. Failure modes are better understood and computerized maintenance methods are becoming mainstream. Condition-based maintenance (CBM) starts to gain ground as a cost-effective alternative, replacing the fixed interval overhauls. As corporations amalgamate and market places are becoming more complex, multi-functional teams become responsible for maintenance. At the beginning of the third generation, maintenance organizations began embracing technology to provide efficiencies in maintenance management. A strong push was made to transition from reactive maintenance to proactive maintenance. At the forefront of this push is condition-based maintenance.

Jan 1, 2004

By Y. Faitakis, G. J. Powley, C. Mackenzie

"In the mining industry, maintenance is a key priority and a major expense. As mining equipment is large in scale, high in cost, and difficult to tow, it is key to maintain equipment on a timely basis. Breakdown in -40°C or away from a maintenance station can cause great costs in repair as well as lost production.It has often been quoted that about 5% of the North American production is lost every year due to unscheduled downtime. About onethird of the downtime is attributable to equipment failures. From this fact alone, it is evident that proper equipment maintenance can add tremendous value to the bottom line. As organizations and equipment become more sophisticated, maintenance expectations begin to evolve. This evolution can be traced through three generations:The first generation (1940–1950): A “fix it when it broke” attitude prevailed during that time, mostly because the industry was not highly automated.The second generation (1950–1980): Automation and mechanization of the industry increased. The industry now was dependent on machines performing the majority of the work. Preventive maintenance (overhauls at fixed intervals) appeared as the first maintenance practice. Maintenance costs started to rise rapidly.The third generation (1980–): Assets become more complex. Failure modes are better understood and computerized maintenance methods are becoming mainstream. Condition-based maintenance (CBM) starts to gain ground as a cost-effective alternative, replacing the fixed interval overhauls. As corporations amalgamate and market places are becoming more complex multi-functional teams become responsible for maintenance.At the beginning of the third generation, maintenance organizations began embracing technology to provide efficiencies in maintenance management. A strong push was made to transition from reactive maintenance to proactive maintenance. At the forefront of this push is condition-based maintenance."

Jan 1, 2004

By Zhuo Chen, Jun Zhou, Jiemin Zhou

Samples of the reacting suspension particles were taken from the reaction shaft of a commercial flash furnace at different heights. The processes of matte and slag formation and morphology of the samples in the shaft were observed and analyzed. Variations of matte and slag composition in the shaft were investigated. By analyzing the samples taken from the settler at different locations, settler processes were studied such as slag formation, agglomeration and separation of matte-slag phases, Fe3O4 reduction, copper-in-slag reduction etc. In accordance with the characteristic of matte and slag formation the flash furnace can be divided into 6 functional regions, and a mechanism model called as “Micro bath process” is proposed for matte and slag formation in a commercial flash furnace. INTRODUCTION During flash smelting, concentrate particles scattered in the reaction shaft complete their oxidation reactions in suspension. The droplets produced fall into the settler beneath with a small amount of un-melted solid particles, agglomerate and separate into matte and slag layers which are tapped out from their tap holes separately. With respect to the extent of slagging reaction in the reaction shaft, there isn’t any commonly accepted understanding in literature (Kimura, Ojima, Mori & Ishii, 1986; Kemori & Kondo et al.,1988; Kemori, Denholm & Kurokawa, 1989; Fagerlund &Jalkanen, 2000). Some assume that the slagging reaction in the shaft can be ignored and some propose that all slag is produced in the shaft. With regards to the characteristics of the physical-chemical changes of concentrate particle in the reaction shaft, although there are some research results reported from pilot scale and commercial scale experiments (Kemori, Ojima & Kondo, 1988; Hagni, Vierrether & Sohn, 1988; Jorgensen, Taylor, Dickinson & Stevenson, 1992; Swinbourne, Simak & Yazawa, 2002; Kivinen & Tuominen, 2005), they are generally limited themselves to theoretical analysis and calculations. No studies are published concerned with the processes of matte and slag generation in the shaft, quantitative analysis of the processes, variations of matte and slag composition and morphologies of the melts along the axis of the shaft, etc.

Jan 1, 2019

By Unknown

With the present-day trend of rising labour costs and a lowering of production efficiency of workmen, it has become imperative that every effort be made to use manpower to the greatest advantage and to mechanize mining as much as possible. During the past few years this trend has gained much prominence in the Porcupine camp. In view of this, the executive of the Porcupine Branch considered that the Mechanical Movement of Muck would be a very timely subject for a Symposium. Accordingly a Committee was formed, with A. K. Douglass, Mine Superintendent for Delnite Mines, Ltd., as Chairman, and the Symposium was held in the Auditorium of the McIntyre Community Building, Schumacher, on March 25th last. Papers dealing with shovel loader and mechanical scraper operation at six of the larger mines of the camp were presented and discussed, and a tabulation was prepared giving data on the machines in operation at a total of eleven mines. The papers and tabulation, reproduced below, will doubtless be of considerable interest to operators of mines in all parts of Canada.

Jan 1, 1948

By Sejong Kim, Younghoon Moon, Youngseon Lee, Eunyoo Yoon, Yonghyun Song

"Mg alloy has a high specific strength, however, their thickness reduction was limited on most parts because of their poor stiffness. Since the modulus of rigidity is an intrinsic property, improvement of modulus of rigidity to the enhancement of stiffness is impossible. Therefore, the modification of shape and structure is available method to enhance the stiffness of real part fabricated by Mg alloy sheet. There are many thin walled parts which are located in outer section of electromagnetic system.Poor stiffness is often shown on wide surface area part with steel sheet, which has also high modulus of rigidity. In these cases, various groove patterns are used to increase the stiffness of part. However, some different methods have to be used when general groove pattern can’t be used. So, we would like to propose some new method to high stiffness on thin walled precision forging of Al or Mg alloys.An effect of proposed method on stiffness enhancement can be confirmed by fabrication of prototypes as well as structure and forming analysis based on FEM."

Jan 1, 2015

By Dave Bulled

"This paper describes the design of a molybdenite flotation circuit using FLEET technology applied to kinetics data produced from laboratory flotation testing and distributed across the blocks of a mine plan using a geostatistical approach. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the kinetics estimates of each block of ore in the mine plan. The final design then included a quantification of risk based on the accuracy of the block flotation kinetics and model fitting. The design made reference to the extensive technical reports describing earlier metallurgical test work including some pilot plant work over thirty years ago.The testing involved conducting MinnovEX Flotation Tests (MFT) to determine the rougher flotation kinetics at the specified reagent conditions and rougher-cleaner tests to determine the change in kinetics resulting from regrind. These flotation kinetics were used within FLEET simulations to create a full-scale flowsheet and plant design including recommended equipment sizes and the forecast of operating results. Measurement of detailed flotation kinetics for a wide range of samples allowed the effect of size of grind and efficiency of classification (i.e. width of size distribution) to be predicted for the whole ore body.INTRODUCTIONAdanac Moly Corp. proposed to develop a 20,000 ton per day mill to produce high quality molybdenite concentrate from its Ruby Creek resource in north-western British Columbia. It is a relatively clean low grade porphyry-monzonite occurrence containing minimal quantities of other sulphides such as chalcopyrite, pyrite, sphalerite and galena. Molybdenite occurs mainly as coarse flakes with lesser amounts of finer sized values. An optimum plant design was required to can achieve the predicted operating results, at a known level of risk, while treating the variability inherent in the ore body."

Jan 1, 2007

By P. T. O'Kane

"INTRODUCTION Wright Engineers Limited is active and has extensive experience in the design of pressure oxidation plants for the treatment of refractory gold ore and concentrate. In addition to the Mercur oxidation facility, similar projects undertaken during the last few years include the 3000 ton per day acid oxidation plant for the Getchell Mine, Nevada, a concentrate treatment autoclave for Asamera in 1984 and a feasibility study of a 50-tons per day autoclave plant for Consolidated Professor's Duport property in Ontario. The Equity Silver antimony and arsenic precipitation autoclaves, and the low pressure autoclaves at Key Lake Uranium in Northern Saskatchewan were also engineered by Wright in recent years.In August 1986, Wright was retained by Barrick Resources (U.S.A.) Inc. to add a 750 tpd pressure oxidation circuit to the existing mill at their Mercur Gold Mine, Utah. This paper describes this facility and outlines the start up in the spring of 1988 and subsequent successful operation. MERCUR OPERATION The Barrick Mercur Gold Mine is located at the south end of the Oquirrh Mountains in Tooele County, Utah. The carbon-in-leach (CIL) process plant camnenced operation in 1983 with a design throughput of 3000 tpd and has since been expanded to handle rrore than 5000 tpd. 'IWo ore types are mined, an oxide ore and a refractory ore, which is by Barrick's definition ""an ore from which less than 60% gold extraction is achieved by a standard CIL amenability test."" Typical of many sulphidic/carbonaceous ores, the refractory gold does not respond well to the cyanidation process. As a result, refractory ore has been stockpiled since the start of mining. As of June 1987, Mercur had about 570,000 tons of refractory ore stockpiled and 5.7 million tons of proven and probable reserves, grading 0.06 oz/t including approximately 3.5 million tons of tailings from the previous operation grading 0.55 oz/t. In 1986, Barrick decided to build a 750 ton per day pressure oxidation plant to process these ores. The process, for which a patent was granted, comprises pressure oxidation of the sulphides in an alkaline environment. It was developed in 1981 but was set aside in preference of a CIL plant treating only oxide ores by the previous owner of the property, Getty Oil. This process is capable of increasing gold recovery from the refractory ore from as low as 35% by conventional CIL processing to more than 85%. In 1986 Wright Engineers was engaged to undertake a feasibility study based on batch testing. This lead to a decision by Barrick Mercur later that year to build the commercial pressure oxidation plant. Wright was awarded the contract for engineering, procurement, construction managernent and commissioning in March 1987. The plant was mechanically complete in January 28, 1988, and was in operation by February 1988."

Jan 1, 1989

By Gabka T., R. E. Gregorczyk

Work to improve employees' behavior in Głogów Copper Smelter began in 2009. It has been noted that over 90% of accidents at work are attributable to human reasons. At that time, a series of external workshops was contracted based on exercises conducted by a psychologist trainer with supervisors. Having trained about 300 employees, an observation of employee behavior at workstations was started as part of the control of risk reduction measures. As a result of the above actions, the number of accidents was reduced by half between 2009 and 2017. Currently, internal workshops for communication improvement for behavioral auditors are conducted by the employees of the Smelter. Named: "I observe, react and communicate" and aimed at further mastering the elements of the safety culture in Głogów Copper Smelter. INTRODUCTION KGHM Polska Miedz is an integrated mining and smelting copper producer based in Poland and operates on the international metal market. KGHM, with annual production of over 500 thousand tonnes of copper, holds a middle position in the world ranking of copper producers. At the same time, in Europe it is the largest producer of copper from its own ore deposits, possessing its own integrated production structure, from underground mining operations to final, top-quality product. It is also worth mentioning that KGHM Polska Miedź is one of the largest Polish exporters and, apart from copper, is a significant primary silver producer in the world. The mission of our company, consistent with its strategy, is to produce copper and silver in a safe mode for workers and the environment, with reduced environmental impact. Therefore, "Głogów" Copper Smelter operations are continuously focused on the creation of safe working conditions, and minimizing the negative effects on the environment. The company meets the requirements of an Integrated Management System comprised of the following: Quality Management System ISO 9001:2008 Environment Management System ISO 14001:2004 OHS Management System according to the requirements of BS OHSAS 18001:2007 Being a proud socially responsible company, we are aware that part of an efficient OHS system is to recognize, monitor, prevent, educate and motivate, thus continuously improve working conditions for 2500 employees of Głogów Copper Smelter &Refinery. We clearly communicate that a low accident rate is beneficial for both, staff and the company, and is of utmost importance as a part of our health policy.

Jan 1, 2019

"This generic study has been developed in response to the frequently asked question, ""That is the best treatment route for refractory gold ore?"". The study has developed operating and capital costs for many potential treatment routes and they are presented here in a generic form. All costs are in relation to the value of 1.00 given to the base case, a 1000 mtpd bio-oxidation plant, operating at 25% solids and 72 hours residence time.There is unfortunately no simple answer to the above quest ions. The treatment of refractory ores is a complex subject, with many variables, such as mineralogy, chemistry, environment and tonnage. However this study does offer information and relative numbers that we believe will be of assistance to gold metallurgists in obtaining a ""first shot"" at estimating costs.Equally, this technology is a rapidly evolving one. As more plants are commissioned, and test programs completed, better data is constantly being generated. For a generic study of this type to remain useful it will need regular updating and adjustment."

Jan 1, 1989

By F. J. Tozer

Canal communication between Lake Erie and Lake Ontario has been one of almost constant enlargement and reconstruction to meet the rapid growth of trade and commerce, and the consequent steady increase in the size of vessels plying the Great Lakes. The original canal was built by the Welland Canal Company. The first sod was turned in 1824 and the first vessel passed through in. 1829. There were 36 lift-locks, built of oak timber, 110 feet long and 22 feet wide, with a depth of water over the sills of 8 feet. The second canal, now known as the 'Old Welland Canal' was built by the Dominion of Canada (1842 to 1850). There were 26 masonry locks, 150 feet long, 26.5 feet wide and with a depth of water over the sills of 9 feet. The walls and banks were raised in 1853 to give a 10-foot draught. The third canal, known as the 'New Welland Canal, built by the Dominion of Canada, was started in June 1874 and the first boat passed through in the spring of 1882. There are 25 masonry lift-locks, 270 feet long, 45 feet wide and with a depth of water over the sills of 12 feet. The walls and banks were raised in 1891 to give a 14-foot draught. This is the canal in use at present.

Jan 1, 1926