Search Documents

By D. Duffy, V. Papangelakis

"MgCl2 brines present a number of potential advantages for the processing of saprolite ores for nickel production. With a chloride system it is economically requisite to recover hydrochloric acid, which can be performed in a more energy efficient manner by precipitation and subsequent decomposition, as compared with conventional pyrohydrolysis. In addition, concentrated MgCl2 solutions enhance the activity of acid used, allow atmospheric leaching at elevated temperature and inhibit magnesium dissolution, which reduces acid consumption and increases metal selectivity. Leaching and iron control experiments have been conducted in concentrated MgCl2 brines, up to 4.5 m, to determine the most amenable process conditions. INTRODUCTIONChloride metallurgy has received an increasing amount of attention in recent years, especially with respect to the treatment of nickel laterites. Although the limonitic fraction can sometimes be economically treated by High Pressure Acid Leaching (HPAL), acid-consumption problems are encountered with the higher magnesium content of the saprolite fraction. As magnesium does not hydrolyze under HPAL conditions, as iron and aluminum do, any sulphuric acid used to leach magnesium is subsequently neutralized and wasted. In addition, this magnesium must later be disposed of in some fashion, further complicating the process. The most common method used to process saprolite is the Rotary Kiln-Electric Furnace (RKEF). This uses a kiln to dry and preferentially reduce nickel, before sending the calcine to an electric furnace. Although nickel recoveries are high, and the problems of acid consumption are avoided, the capital and energy costs associated with this process are high (de Bakker, 2011).The problems outlined above have led to the investigation of an atmospheric chloride process for the treatment of saprolite ores. The use of a chloride system presents a number of advantages, but also a few limitations. Metal chlorides tend to be very soluble, with a few notable exceptions (silver, mercury and lead), allowing for smaller processing equipment through more concentrated solutions. This solubility also serves to reduce the potential for scale formation. In addition, a hydrochloric acid leach is more aggressive than a comparable sulphuric acid system, and the activity of the hydrogen ion can be augmented by further chloride addition (Peek, 2011). This activity augmentation in concentrated chloride systems, first reported by Jansz, has repeatedly been referenced as a motivating factor behind chloride hydrometallurgy (Jansz, 1983; Harris and Magee, 2003; Harris et al., 2004; Demopoulos et al., 2008; McDonald and Whittington, 2008; Demopoulos, 2011; Peek, 2011; Verhulst and Lakshmanan, 2011). This activity increase allows a similar amount of acid to perform more in a concentrated solution than in a dilute solution, decreasing overall acid requirements. As such, much focus has been placed on leaching in concentrated chloride systems, or brines, using calcium, magnesium or sodium as the cation (McDonald and Whittington, 2008)."

Jan 1, 2012

By A. I. Collins, D. Danninger

Newmont has installed advanced control and online optimization on the dry grinding circuit and both roasters on its Carlin Trend refractory ore treatment plant. Subsequently, Newmont has developed a master plan for institutionalizing advanced control and optimization on all its processing units. Newmont is committed to a program of applying advanced control and optimization from crushing of ore to pouring of gold. This paper describes Newmont's experience with implementing advanced control and optimization and the benefits received. In addition, identification of advanced control and optimization opportunities and their economic justification is discussed.

Jan 1, 2005

By J. Mizera, B. Adamczyk-Cieslak, K. J. Kurzydlowski, A. Dobkowska

"AZ31 is the one of the most popular magnesium alloy using in the modern industry. It is well known, that compared with steel, magnesium alloys posse better properties, such as light mass, high specific strength or thermal conductivity. It should be noted that their application is limited by poor corrosion resistance. In this work the corrosion behavior of AZ31 magnesium alloy as cast and after heat treatment were described with the use of testing in neutral salt spray atmosphere.To characterise corrosion resistance and describe layers built on the surface it was necessary to do the metallographic observations with the use of optical microscopy. After that influence of heat treatment for AZ31 corrosion resistance was examined. Measurements were conducted by electrochemical impedance spectroscopy (EIS) and by neutral salt spray tests in artificial atmosphere. Surface and cross section morphology after removal of corrosion products were observed with the use of scanning electron microscopy (SEM).The weight loss measurements show that there is no significant difference between alloys as cast and with following heat treatment.INTRODUCTIONMagnesium and magnesium alloys are popular in modern industry because of the low density and good formability. Magnesium alloys are described by few properties which have got significant influence for their application in transportation and electronics industries (Feliu & Liorente, 2015). Their wide application is limited by poor corrosion resistance. As it is well known Mg is one of the chemically most active metal. Corrosion resistance of Mg alloys depends on several factors, such as impurities, chemical composition or working conditions (Cheng, Qin, Wang, & Zhang, 2009). That all causes that there are many different ways to find well defined and good solution of magnesium alloys processing to improve their corrosion resistance.There are many different versions about the influence of aluminum on the corrosion resistance of magnesium alloy. It is known that intermetallic compounds such as Mg17Al12 due to ß-phase content plays the minor role for corrosion resistance. It is proved ß-phase acts as cathode and it has good ability to build passive layer in broad pH ranges. However it should be noted that mentioned behavior depend on size and distributions of ß-phase in the microstructure (Singh, Singh, & Das, 2015)."

Jan 1, 2016

By H. Vermette, J. Demers, R. Leclerc, P. Bergeron, P. Hudon, A. Lessard

The Arvida Smelter marked its 80th anniversary in 2006. Arvida currently operates 6 potrooms equipped with prebaked side-feeding pots producing 160 000t of aluminum per year, requiring the supply of 300 000t of alumina per year. In the past, to ensure reliable alumina supplies to the pots, especially in winter, a safety stock of alumina was kept inside the plant. The improved reliability of shipping on the Saguenay River has cut the need for such a stock. However, the stoppage of 8 Soderbergtechnology potrooms, starting in the 1980s up to 2003, generated alumina from the cleaning of pot pits, totaling 18000t and leading to the building-up of a significant alumina stock again. Concerns over working conditions, effect on potroom operations, and dust emissions prevented Arvida from tackling effectively this impressive alumina stock. Yet the increasing cost of alumina has created a strong motivation to use the stored alumina. In 2004 Arvida launched a project to recycle the stored alumina. This 4-year project aimed at clearing the alumina stock without affecting the operation of the smelter. It involved changing work organization, improving equipment and controlling the effect of the recycled alumina on the smelting process and working conditions.

Jan 1, 2006

By Eddy Dénommé, Deni Villeneuve

"Niobec mine, a producer of pyrochlore concentrates since 1976, became a producer of ferroniobium in 1994 and achieved accreditation to the ISO 9002 standard in 1995. The goal of ISO 9002 is to ensure that the products supplied to clients regularly meet their specifications, through explicit work standards and procedures throughout the production process, from deposit appraisal to ferroniobium production.A key element of ISO 9002 implementation at Niobec consists of the quality control procedures applied to the raw materials: the ore fed to the mill and the pyrochlore concentrate fed to the reduction plant. These controls extend from exploration, deposit appraisal, mine planning and reserves estimation, mining, mineral processing and, finally, ferroniobium production. The implementation of ISO 9002 has allowed more efficient control of the quality of the final product sold to clients. It requires interactive team work, the role of the geologist being to relate all information pertaining to raw material and product quality to the geological framework of the deposits."

Jan 1, 1997

By John Lamb

"The French Mine (formerly the Oregon) is 4 miles by road south of the Nickel Plate Mine. It lies on the steep eastern slope of the Similkameen River valley at elevation 4,000 feet, between Cahill and Winters Creeks.The property was discovered in .1901 and bought 4 years later by Messrs. French and Deardorf. It was developed in a modest way by the owners and by several companies until 1947, without success. The spectacular showings of bornite and chalcopyrite in the outcrop drew attention to its possibilities for copper rather than gold. Diamond drilling by the owners in 1947 yielded several high-grade gold intersections and created new interest. In 1949 the property was purchased by Kelowna Mines Hedley Limited. Exploration drilling and geological mapping outlined sufficient ore to commence production in 1950. Except for a few months each winter the operation has been continuous, and to the end of 1954 had produced almost 30,000 tons of high grade ore. The ore is crushed at the mine and hauled 8 miles by truck to the Company mill at Hedley, where it is treated together with the ore from Nickel Plate.Regional GeologyThe country rock consists of brown tuff, flows, limestone, and cherty formations belonging to the Nicola group (Rice 1947) of Triassic age. West of and just below the mine is a large mass of granodiorite which is part of the same body that underlies Nickel Plate Mountain. Bedding attitudes in the mine area are locally complicated, but dips are generally less than 45 degrees. To the south and below the mine the beds stand almost vertical, continuing downward with this attitude for 2,000 feet to Winters Creek. The main granodiorite contact is also steep, conforming to the sedimentary formations, whereas northward towards Nickel Plate it dips gently to the northwest, slightly flattter than the thick westerly dipping pile of sediments above it. The interpretation of this structure by Billingsley (1936) is that the French mine lies near the crest of the large northeasterly trending asymmetrical anticline which contains in its gently dipping western limb the Nickel Plate orebodies. The granodiorite body conforming roughly to this shape seems to occupy the core of the anticline. Sill-like prongs of granodiorite extend upward to the east from the main mass, outcropping over wide areas at the head of Winters Creek (Figure 1). There is a possibility that overthrusting from the west, similar to that on Nickel Plate Mountain, occurs not far below the French mine.An interesting feature of the granodiorite-sediment contact is that where it dips gently westward no alteration exists in the sediments, but where it has a steep front pronounced heat effects are indicated by the presence of a thousand-foot-wide zone of reddish garnet skarn."

Jan 1, 1949

By Changyoon Kim

Technological advances in mobile systems, such as smartphones and tablet computers, provide engineers with new opportunities to enhance the current facility management processes. Equipped with powerful system processors, touch screens, and wireless communication capabilities, mobile systems enable the experience of omnipresence of facility information. Building information modeling (BIM) also enables improvements in facility management. With an advanced data structure and visualization capacity, BIM can be used in numerous applications for facility management. This study aims to incorporate the strength of mobile systems and BIM in facility management. The proposed system, which utilizes smartphone technology, allows engineers to conduct facility management functions, such as maintenance planning, inspection, and assessment, irrespective of a user?s location. The integration of building information modeling in a system provides detailed visual information of the building components. A case study was conducted to verify the applicability of the mobile system in terms of the hardware functions, system design, and user interface. This proposed system, with its study results, provides a guideline as to how mobile systems can be effectively integrated with BIM for improved management of facility information.

Aug 1, 2013

By C. Hunt, J. Vivas, D. M. Allen

"In this paper we present the results of a combined remote sensing - numerical modelling study to improve our understanding of groundwater seepage in open pit and natural rock slopes, and to investigate the interaction between groundwater, in-situ stress conditions and brittle fracture. The location of seepage is a key element in the characterisation of rock slope stability in open pits and natural slopes; definition of the fracture network geometry and its inter-relationship with seepage, however, remains a challenge in engineering practice. Current techniques used to characterize groundwater seepage locations require direct access to the rock slope for a detailed and exhaustive investigation, and can be severely limited due to access and the limited coverage of the survey methods both with respect to the height and length of the sampled rock slope. Herein, we describe remote sensing methods, which allow the collection of structural and seepage information over a wide spatial area. Remote sensing techniques are shown to have the potential to provide additional insights into the orientation and general connectivity of fractures that may play a major role in the general stability of a rock slope. A preliminary methodology for the use of remote sensing in the characterization of seepage zones in a natural slope through the application of ground-based LiDAR and Infrared Thermography (IRT) is presented.One of the most challenging problems in rock slope engineering is the realistic simulation of fluid flow through fractured and deforming rock slopes. Deformation and the development of brittle fractures can cause significant local changes in the permeability and strength of the rock mass, potentially affecting rock slope performance. Understanding fluid flow through fractured and deforming rock slopes, especially in highly-stressed environments is of great importance for slope stability analysis. Changes in the interconnectivity of fractures during slope failure are an important, yet are relatively unstudied in rock slope engineering. We present the results of hydromechanical UDEC-Trigon rock slope models focussing on the potential role of brittle fracture in rock slope failure, its interaction with groundwater pressures, and the influence of the assumed in-situ stress ratio. Damage intensity parameters are used to characterize damage within different regions of a biplanar slope failure."

Jan 1, 2015

By S. Shairp

Copper is an impurity as well as a necessary reagent in the processing of zinc sulfide concentrate at Hudson Bay Mining & Smelting Co., Limited's (HBMS) zinc pressure leach plant. Copper is present in the zinc concentrate as chalcopyrite, which consumes reagents necessary for zinc leaching. A small percentage of copper precipitates in the autoclaves, discharge lines, and flash tanks, requiring maintenance of the equipment and disposal of the solids. Copper also precipitates in the neutralization stages and is removed to low levels in a specific copper removal stage of purification. Yet some copper, as copper sulfate, is required, along with potassium antimony tartrate, in the final purification stage to improve cobalt removal from the zinc sulfate solution prior to electrowinning. The behaviour of copper experienced at HBMS's zinc pressure leach plant is discussed.

Jan 1, 2008

By J. A. Orr

The details connected with the mining and subsequent handling of Creighton ore were fully covered in a paper presented to the Institute in 1920. The following brief notes describe certain phases of the present practice and show wherein it differs from the practice at that time. These may be summarized under the following headings. (a) Recovery of pillars. (b) Drawing the ore. (c) Change from sub-level tramming to branch-raise system. (d) Chute construction. The present stoping practice is the same as formerly, i.e., fiat-backed shrinkage stopes of 60-foot width, between rib pillars of 15-foot width, extending from the footwall to the hanging-wall. Formerly, when these stopes were completed to the stopes above, they were drawn empty of broken ore, and the 15-foot rib pillars were caved into the stopes and drawn off through the same chutes as were used to draw the ore from the stopes.

Jan 1, 1926

By J. L. Jambor, E. J. Reardon, E. C. Appleyard, J. A. Cherry

Abstract- Since the 1957 initiation of deposition of mill tailings at the Heath Steele mine, New Brunswick, periodic detailed studies of the tailings geochemistry and mineralogy have been con­ ducted, thereby providing a unique opportunity to examine the geochernical evolution of a sulfide- rich mine-tailings impoundment. When deposited, the tailings contained about 85 wt% sulfide minerals, 1 wt% to 3 wt% carbonate minerals, and 12 wt% to 14 wt% aluminosilicate minerals. Mineralogical examination of samples of the tailings from deep in the impoundment indicates that little oxidation occurred prior to tailings deposition. The mill process-water deposited with the tailings was neutral to slightly basic and contained low concentrations of Cu, Pb, Zn and As. Sampling of the tailings five years after deposition indicated that sulfide-oxidation reactions, occurring near the tailings surface, had decreased the tailings-water pH and increased the concentrations of Fe, SOi-, Cu, Zn and Pb (up to 10 000 mg/L, 25 000 mg/L, 2.5 mg/L, 200 mg/L, and 4.5 mg/L, respectively) . In 1975, ten years after decommissioning, the tailings could be divided into three zones: an upper oxidation zone in which sulfide oxidation is actively occurring, a hardpan layer, 15 cm to 20 cm thick, composed of tailings cemented by secondary Fe minerals, and an underlying reduction zone in which the tailings are relatively tinoxidized (Boorman and Watson, 1976). Chemical analyses indicated the presence of low-pH waters containing very high concentrations of SO42- , Fe, and other metals (up to 63 600 mg/L SO42-, 28 600 mg/L Fe, 10 mg/L Pb, 600 mg/L Cu and 4000 mg/L Zn), suggesting that there was a period of intense sulfide oxidation between five and ten years after tailings deposition. More recent sampling, conducted some 20 years after the end of tailings deposition, indicates that relatively little change has occurred in the last ten years, thereby suggesting that the hardpan layer has provided an impediment to the downward movement of dissolved constituents . Analyses of the tailings solids show increased accumulations of many metals at or near the depth of the hardpan layer. Evaluations of the long-term evolution of the tailings can be enhanced by comparison of descriptions of the tailings with descriptions of the gossan that overlay the massive­ sulfide orebody prior to mining. At Heath Steele, this comparison suggests that many of the mechanisms controlling the distribution of metals in the tailings will probably persist over geologic time.

Jan 1, 1992

By Fiona Campbell

"Modern history is full of breakthroughs in technology, all striving to increase productivity and efficiency. What are the elements that should be taken into consideration in the design and implementation of modern automation systems in a control room? Both industry and international standards are now demanding that Human Factors be considered as part of the design of control rooms to maximize efficiency and minimize the potential of human error which can lead to downtime and a loss of profit as a result of interruptions in production. As the current workforce ages and the younger generation matures, this is also becoming a key element when planning a control room. New standards are helping to address some of these challenges that are facing the mining industry today. With an increased focus on the operator, an intelligent and ergonomic workspace can both mitigate risk and optimize production. Optimization is money. We will examine how to analyze and implement innovative control room planning to maximize mineral processing production and minimize risks that can impact overall production and profit.INTRODUCTIONIn this day and age, optimization of production in an industrial environment is becoming more and more of a challenge. With ever changing technology as well as other external factors, this can be especially daunting. There are several key elements that may not be immediately obvious when planning a control room design or renovation, most notably the role of the human in this environment. Fatigue, stress, distraction, reaction times and situational awareness are all critical in a 24/7 environment. With the growing need to include human factors when considering and designing an optimal work and production environment, it is becoming even more important to design a control room that can address as many of today’s challenges as possible.The standard definition of the word “optimization” is “an act, process or methodology of making something (as a design, system, or decision) as fully perfect, functional or effective as possible.” (www.merriam-webster.com). If we apply this to business, what it really means is finding the most cost effective way to achieve the highest level of performance while considering constraints, both external and internal, by maximizing the desired factors and minimizing undesired ones. Sometimes, however, we can get caught up in the day to day processes, without taking a moment to step back and objectively review what it is we need to achieve, and more importantly, the steps that can facilitate our success."

Jan 1, 2016

By John C. McKay

"The five papers which follow, under the heading of ""Technology Transfer-Universities to Industry"", were originally presented at the 20th Annual CIM Conference of Metallurgists in Hamilton, Ontario. They are a unique group of papers, unique because each paper is concerned with applied research done wholly or partly in a university environment and then translated into industrial practice.Universities can rightly be regarded as one of our nation's greatest resources-a veritable storehouse of knowledge and expertise. Yet, too often, this resource is overlooked or, at best, sparingly used by Canadian industry. Of course, university-based research cannot supplant industry-based research, nor vice versa; each type of research activity has its proper role in the over-all process of technology development.University-based scientists are best equipped to conceptualize, innovate, determine viability of basic premises and to verify these at the bench or small pilot-plant level. Industry based scientists are best equipped to develop ""bench-scale"" innovations into mature manufacturing practices. Thus, university-based scientists and industry-based scientists do not compete with, but rather complement, each other. Active, relevant university research enhances industrial research provided good communication between the two ""solitudes"" is continually nurtured.Good communication between industry and university is a prime objective of CSIRA/ACRIS (Canadian Steel Industry Research Association /Association Canadienne pour la Recherches dans d'Industrie Siderurgique), The directors of CSIRA/ACRIS foster improved communication by making regular visits to universities, by sponsoring projects and by providing lists to professors of uncharted areas where basic research is needed. More can be done to improve communication between industry and university, and it is the intent of the Association to do more.The five papers sponsored by CSIRA/ACRIS are examples of good communication and healthy cooperation. It is interesting to note when reading these papers that the cooperation arose, in each instance, as a result of different circumstances. However, there is a common thread and it is personal acquaintanceship-the university scientist/professor and the industry investigator/manager knew each other prior to the initiation of the project."

Jan 1, 1982

By C. Nikolic

A process utilizing ozone for the precipitation of cobalt from nickel sulphate liquors containing ammonium sulphate has been developed. Best results were obtained using nickel carbonate to maintain solution pH at 5.0 to 5.5. Work was performed both in column and stirred-tank reactors. Variables studied included neutralizer type and concentration, NH4+ concentration, temperature, Ni++ and Co++ concentration, per cent O3 in the O2 carrier gas, O3 input rate and agitation. The over-all rate of cobalt rejection increased sharply with increasing agitation and ozone concentration in the gas phase, reflecting relatively slow transfer of ozone from the gas to the liquid phase.

Jan 1, 1978

By Lawrence D. Hoy, Armand Savoie, Pierre Trudel, Ghislaln Tourigny, Robert Crépeau, Lao Kheang

"Recent fluid inclusion and stable isotopic studies in the Bousquet mining district have identified spatial and temporal trends in mineralization temperatures and isotopic compositions of vein forming fluids. These studies indicate that mineralizing temperatures were lower during sterile vein formation (T=200-300°C) than during auriferous vein formation (T = 300-400°C), and that 8 80 values of minerals in sterile veins are lower by 1-3 %o than in associated auriferous veins. In addition to these small differences in 8 80 within individual mineralized zones, a trend of increasing 8 80 values of vein minerals is identified from west to east across the district, with 8 80 of vein minerals increasing by4-6%o. Quantitative evaluation of potential causes of the observed oxygen isotopic shifts suggests that the best explanation for these trends is the derivation of the mineralizing fluids from an isotopically inhomogeneous terrain in which the fluid isotopic compositions are controlled by the isotopic compositions of the host lithologies due to high rock/water ratios in these source terrains. This inhomogeneous source terrain is interpreted as consisting of the Blake River Group volcanics (low 8 80 component) and the adjoining Kewagama and Cadillac Group sediments (high 8 80 component).The genesis of the hydrothermal fluids is attributed to crustal heating during metamorphism, with the fluids representing metamorphic dewatering products and/or fluids incorporated during deposition and burial of the host lithologies. Ductile deformation of the fluid source regions impeded fluid migration during metamorphism; the ultimate release of the mineralizing fluids is attributed to the penetration to depth of vertical structures (fault and shear zones) during brittle deformation of the crust under waning metamorphic conditions. Release of fluids caused by this puncturing of the closed hydrologic source regime produced a localized zone of lowered pressure, drawing fluids from adjacent lithologies toward the fault zones, feeding further hydrothermal fluid upwelling. Au mineralization resulted from chemical processes related to cooling of the hydrothermal fluids and/or interaction with lithologies encountered during fluid migration; the level of crust at which Au deposition occurred likely migrated upward with the thermal anomaly caused by hydrothermal fluid upwelling, eventually reaching the level of current exploitation. Cessation of fluid flow along the vertical structures is attributed to inadequate recharge of the hydrothermal systems as fluid contents were depleted in the lithologies proximal to the vertical structures and/or sealing of the structures by mineral deposition."

Jan 1, 1990

By Y. Thibault, G. Deschênes

An open-pit mine, located in Mexico, processes an ore a rate of 4000 tpd, using conventional cyanidation and AYR. A laboratory study was conducted to increase silver extraction and to reduce the concentration of cyanide in leaching. The sample contained 0.41 g/t Au, 125 g/t Ag, 99% gangue minerals, 0.7% pyrite, 0.07% sphalerite, 0.03% chalcocite. Silver was present as acanthite, stromeyerite, silver mercury/halogen, silver with copper in solid solution and jalpaite. The plant conditions (2400 ppm NaCN) produced 90.2% gold extraction (residue at 0.04 g/t Au) and 92.7% silver extraction (leach residue at 9.1 g/t Ag). The CELP (CANMET Enhanced Leaching Process) produced 97.0% silver extraction (residue at 3.8 g/t) and 90.2% gold extraction using 500 ppm NaCN. The incremental gross revenue was estimated at $US7.6 million and the reduction of cyanide costs was $2.9 million per year (79%).

Jan 1, 2011

By Tyler J. Irving

"In June, 2018 Lalor Mine experienced a catastrophic blade failure of its No. 2 main exhaust fan. Over the following weeks several key changes were made to the auxiliary ventilation system to allow for continued production while the exhaust fans were repaired. Issues encountered during the period of reduced ventilation, and how they were addressed, are analyzed. The suspected causes of the exhaust fan blade failure and how risk was mitigated during the reconstruction are discussed. Key findings and lessons learned are summarized.INTRODUCTIONLalor Mine, owned and operated by Hudbay is an underground zinc, gold, and copper mine located in northern Manitoba. The mine workings extend to a depth of 1090 metres below surface and is ventilated using a push-pull system. The mine exhausts through the main exhaust raise; equipped with two, 2,500 HP fans and upcasts through a portal located at the neighboring mine, Chisel North. Air is supplied to Lalor Mine through four intake fans: The Production Shaft Downcast (two, 250 HP), Lalor Downcast (one, 400 HP), and Chisel Downcast (one, 600 HP) fans (Figure 1). In June 2018, Lalor was scheduled to produce approximately 4,000 tpd.On June 20, 2018 at 2:52 pm Lalor Mine experienced a fault on the Variable Frequency Drive (VFD) for Exhaust Fan No. 1. Time would be needed to complete the necessary repairs. The No. 2 exhaust fan was ramped up from 525 rpm to 800 rpm, 90% of its capacity, in order to maintain underground ventilation. At 4:46 pm, approximately two hours after the rpm was increased, exhaust fan No. 2 experienced a catastrophic blade failure. The forces from the blade failure resulted in the top half of the fan housing being thrown 50 metres from where it was installed; with several large sections of fan blade being thrown further (Figure 2)."

Jan 1, 2019

By Q. Li, X. -L. Lei

Accompanying global energy shortage and high energy prices, shale gas has been the focus of exploration and it has attracted great attention from both academia and industry. The combination of horizontal drilling and hydraulic fracturing enables the extraction of huge quantities of shale gas from impermeable shale formations. During the process of hydraulic fracturing, great amounts of water, sand and chemicals must be injected into the shale formation at a high pressure, which may trigger seismicity. Such events could occur due to the presence of faults or the reactivation of these potential faults. Shale is the main component of source rock in the Sichuan Basin, China, and has the greatest contribution to the natural gas of the basin. In order to investigate the fracturing mechanism of shale in the Sichuan Basin, China, a series of rock fracture tests under triaxial compression were carried out in the laboratory in order to investigate the hydraulic fracturing behavior in relation to the seismicity. Based on the high multichannel waveform recording system, the detailed spatio-temporal distribution of acoustic emission due to micro-cracking was used to examine the deformation and fracture behavior of shale. In addition, the effects of confining pressure on the deformation and fracture in shale under triaxial compression by acoustic emission monitoring and X-ray computed tomography were discussed in the paper. The experimental results indicate that the shale samples demonstrate brittle fracture behavior. The confining pressure has a great effect on the complexity of the fracture planes and the spatial distribution of acoustic emissions, but few contributions to the location of the major hydraulic fracturing plane. The foliation of shale plays a dominant role in the rupture process and the geometry of the major hydraulic fracturing plane. The high confining pressure increases the strength and restrains the deformation of shale during compression process. These results shed some light on the understanding of onset of hydraulic fracture initiation not only for shale gas exploration and production, but also for CO2 geological storage and underground energy storage.

Jan 1, 2015

By R. D. Brown

Ever since British Columbia started the ball rolling in 1974 with the introduction of its now-defunct Mineral Royalties Act, all Canada's resource-based provinces have significantly altered their mining tax systems. The last resource-based province to abandon its pre -1974 mining tax structure is New Brunswick, which introduced a new mining tax regime in the summer of 1977 to take effect from April 1 1977. The new structure, which represents the outcome of considerable study and discussions with industry representatives, contains some intriguing concepts which make Nero Brunswick's new mining tax system unique among the Canadian provinces.

Jan 1, 1977

By D. Cronin, A. Plumtree, A. Hosseini

"Crack in corrosion (CIC) linepipe defects are hybrid defects not directly addressed by existing assessment methods. To investigate the collapse pressure of these defects, CIC defects were formed in 508 mm (20 in) diameter, 5.7 mm thick API X52 linepipe. These defects were 200mm long and varied in depth from 3.0 to 3.8 mm. The respective failure pressures decreased from 14.3 MPa for the plain pipe to 7.9 and 6.2 MPa respectively. A standard FAD method was applied to evaluate these defects as equivalent length and depth cracks, predicting the rupture pressure conservatively by 18% on average. However, when assessed as equivalent cracks with a reduced wall thickness corresponding to the corrosion depth, the predicted collapse pressures were more accurate, approximately 14% conservative on average.INTRODUCTIONPipelines are a safe and efficient method for transporting high volumes of oil and gas. However, aging pipelines may experience defects, such as cracks or corrosion. Present approaches include detection, assessment and repair of defects before they may become critical to the integrity of the line. There are different codes and standards for assessing pipeline defects, depending on the type of defect, with API 579 (API, 2000) being the most common code for the assessment of cracks in oil and gas pipelines . Corrosion is commonly assessed using RSTRENG (Kiefner & Vieth, 1989). Other methods such as the Finite Element method and the CPS method (Cronin & Pick, 2002) may be used for crack and corrosion, respectively.At present, there is no specific method or procedure for assessing crack in corrosion (CIC) defects, and as a consequence there is a need to provide an assessment and evaluation of the integrity of these defects in order to determine the requirements for defect repair or hydro line testing. Hence, the goal of this study was to provide guidance for the assessment of CIC defects for linepipe.CRACK IN CORROSION DEFECTS (CIC)Significant amounts of corrosion and cracking are not generally found together (Hosseini, 2010). However, a new hybrid defect including cracking within corrosion (CIC) has been identified in operating pipelines. In this case, cracking coincident with corrosion (schematic shown in Figure 1) provides the motivation for the current study."

Jan 1, 2012