Search Documents

By W. S. (Steve) Vaughan

The Origins of Joint Ventures in Canada?s Mining Industry ? Among the most important financing structures used in our mineral industry today ? Virtually unheard of in the Canadian industry prior to the 1970s ? Borrowed from the U.S. oil and gas sector where it came into prominence in the late 1930s ? The Securities Acts of 1933 and 1934 in effect killed the sale of (equity) shares for financing oil and gas wells and start up mining companies

May 1, 2013

By R. P. Hackl, P. G. West-Sells

Carbonaceous gold ores are particularly attractive for leaching by ammonium thiosulfate as the gold thiosulfate complex is not significantly adsorbed by the organic carbon present in the ore. A technically and economically feasible process for treating these ores with ammonium thiosulfate has been developed. In this process, gold is extracted by leaching the ore with ammonium thiosulfate, the solution is separated from the ore by counter - current decantation, the gold is recovered by precipitation with ammonium sulfide, and finally the gold containing product is upgraded by reacting the elemental sulfur present in the precipitate with ammonium sulfite. The precipitation filtrate is recycled back to the grinding step to close the solution balance. Reagent consumption is not excessive. Besides precipitating gold, the precipitation step removes most deleterious solution impurities and converts a portion of the polythionates back to thiosulfate. This paper discusses the optimization of the leaching, precipitation, and upgrading steps. The results of a 10 kg/h pilot plant campaign are also discussed.

Jan 1, 2005

By A. Dave Mackintosh

Historical closure data has provided a description of the stress distribution patterns occurring around mine openings and enabled the development of a time ? distance plot predicting the location of the stress peak and its migration away from mine openings with time. Data collected from active mining areas during the 1970?s and 1980?s indicated the peak appeared to stabilize approximately 135m (450 ft.) from openings after four years. The region of high load and accompanying poor ground conditions in which the peak was centred was spread over approximately 45m (150 ft.) to 60m (200 ft.). Recent data from new development headings cut adjacent to 25 year old extraction areas suggests load transfer takes place over a much greater distance and time frame than predicted.

May 1, 2001

By P. W. A. Mayer

"As the push toward the northern regions of Canada steadily increases to exploit the rich mineral reserves, interest is steadily rising in respect to accessibility and climatic conditions and the problems posed thereby. In twelve years of operation, the Iron Ore Company of Canada, and associated companies, have found, through advanced technology, ingenuity and, most of all. need, some of the answers to the running of a profitable year-round open-pit mining operation."

Jan 1, 1966

By Hasini Wijayaratne

Anode cover material, a mixture of crushed electrolyte and alumina, is a crucial part of an aluminium reduction cell because of its important role in maintaining overall heat balance. However, until recently little attention has been given to understanding or controlling its composition and quality. The thermal conductivity of anode cover material determines the extent of the heat loss from the top of the cell. This will change as a function of the granulometry and composition of the applied cover as well as over time as the cover material consolidates on top of the cell. The ability to measure or predict the thermal conductivity of fresh and ageing cover is an important tool for managing cell heat balance. Recent studies have shown that granulometry or more correctly, voidage is likely to be the predominant determinant of thermal conductivity of anode cover materials. We have developed equipment to measure the thermal conductivity of granular cover material and tested the relative importance of composition (ratio of alumina to crushed electrolyte) and granulometry/voidage on cover thermal conductivity. In general, our results confirm that granulometry is the dominating factor. Generally, high voidages contribute to lowering the thermal conductivity especially when particles are mostly fine. However the relationships between granulometry, voidage and thermal conductivity are complex due to the varying nature of heat transfer between particles. Aging of granular cover material occur during cell operation forming a consolidated crust due to exposure to heat and fumes over time. Structure and thermal behaviour of this consolidated crust is also important in understanding the overall properties of cover. This paper presents the outcomes of laboratory studies conducted in order to understand the thermochemical behaviour of anode cover material and in particular, the role of fines in anode covers mixtures.

Jan 1, 2011

By Andrea Lisjak

The mechanical behaviour of Opalinus Clay, an indurated over-consolidated argillaceous rock, is heavily influenced by the presence of preferably oriented bedding planes. The objective of this study is to illustrate a new modeling approach aimed at capturing the bedding-induced anisotropy of Opalinus Clay as observed in the laboratory and in situ. The combined finite-discrete element method (FEM/DEM) is employed as the main simulation tool. FEM/DEM is a numerical method that models material damage processes by explicitly considering fracture nucleation and propagation. A transversely isotropic elastic constitutive law is used to account for different elastic property values in the direction parallel and perpendicular to the layering, while strength anisotropy is captured using a directional cohesive fracture model. Quantitative calibration and validation of the model is based on laboratory results of indirect tensile tests and uniaxial compression tests. Emergent strength and deformation properties, together with the simulated damage mechanisms, are shown to be in good agreement with experimental observations. Preliminary results relative to the analysis of a circular tunnel show that the approach is able to reproduce the main Excavation Damaged Zone (EDZ) formation mechanisms as observed in the field.

Jun 1, 2012

By Z. Trojanová

The deformation behaviour of ternary magnesium alloys AJ (Mg-Al-Sr) and AX (Mg-Al-Ca) were investigated in tension as well as compression tests. The samples were deformed at temperatures between 20 and 300 °C and at an initial strain rate of the order 10-4 s 1. The flow stress decreases with increasing temperature. The macroscopic work hardening rate decreases with increasing flow stress and temperature. The stress and temperature dependence of the work hardening rate is a result of the hardening and softening processes. Stress relaxation experiments were performed in order to reveal features of the thermally activated dislocation motion. Internal and effective stress components of the applied stress were estimated. A decrease in the internal stress was observed at elevated temperatures, which indicates recovery process (-es). A more detailed analysis of the estimated values of the activation volume and activation energy helped to interpret the thermally activated processes during plastic deformation. It is concluded that the deformation behaviour of the alloys depends on the activity of non-basal slip that is strongly influenced by temperature.

Jan 1, 2007

By Robert G. Boutilier

So far, most social performance monitoring systems have not gone beyond listing the impacts on various stakeholders. Executives have had to rely on intuition to devise interventions that would improve the impacts. This paper describes a survey process, known as the Stakeholder 360 (S360), which eliminates much of the guesswork. The paper reviews key studies showing that raising the levels of communication, trust, and common vision among stakeholders leads to the acquisition of the resources needed to improve the socio-economic situation. Therefore, the Stakeholder 360 measures the levels of these three factors in the relationships between a company and its stakeholders, and among the stakeholders themselves. In a validation study at a gold mine in rural Papua New Guinea, the S360 produced a socio-political ?roadmap? that showed management and stakeholders alike which relationships need more communication, trust, or common goals/vision. Management used the findings to create alliances that helped the government move forward on a regulatory regime for the mine closure. The community used the findings to focus its planning for life after the closure. An S360 survey conducted six months later revealed a decline in dependence on the mine and an overall increase in levels of mutual understanding.

May 1, 2002

By R. Chen, K. Xia

In deep mining activities, blasting induced compressive stress wave would be reflected as tensile wave at a free surface around the openings, which would facilitate the tensile failure of the deep rock since it is much weaker in tension than in compression. It is thus critical to understand the dynamic tensile failure of rocks subjected to static tension for deep rock engineering applications. A modified split Hopkinson pressure bar (SHPB) system is adopted to load Brazilian disc (BD) samples statically, and then exert dynamic load to the sample through stress wave generated by impact. The pulse shaper technique is used to generate a slowly rising stress wave and thus to facilitate the stress equilibrium of samples during each test. Five groups of Laurentian granite (with tensile strength of 12.8 MPa) BD samples under the pretension stress of 0 MPa, 2 MPa, 4 MPa, 8 MPa, and 10 MPa are tested under different loading rates. The result shows that the dynamic tensile strength of the rock decreases with the increase of pre-tension stress, which is easy to understand because pre-tension stress weakens the rock sample. It is also observed that under the same pre-tension stress, the dynamic tensile strength increases with the loading rate, revealing the so-called rate dependency that is common for engineering materials. Furthermore, it is found that the loading rate sensitivity of the rock increases with the increase of pre-tension stress. A qualitative explanation for this phenomenon is that more microcracks are generated and activated under higher pretension stress, resulting in a more viscous material. Based on the results, an empirical equation is proposed to fit the data and explain the dynamic tensile behaviour of rock under pre-tension stress. A physical model is used to simulate the dependency of the dynamic tensile strength of rock on the pre-tension stress and the loading rate, which is shown to be in good agreement with the experimental results.

Jan 1, 2015

By R. Pot

"IntroductionTHE PURPOSE of this paper is to discuss briefly the main logging and testing devices presently at our disposal, to point out some of their limitations, and to suggest possible improvements of the techniques.Some of the more important devices .are those that are used in:(1) Coring(2) Formation testing(3) Electric well logging(4) Radioactive well logging(5) Measuring of bottom hole pressures(6) Sampling of reservoir fluidsThe first four of these procedures are concerned with the well while it is in the process of drilling. The last two are carried out as soon as possible after a well has been brought into production and .at intervals during its life. My remarks will be concerned mostly with certain aspects of formation testing. The reservoir engineer is dependent on the information derived from these operations in order to obtain a clear picture of the conditions in a reservoir and to enable him to assess and forecast its future behaviour.Since any calculation is no better than the data on which it is based, not enough emphasis can be placed on the necessity for the testing and logging equipment to be of the highest quality and for the analysis of the results obtained to be thorough."

Jan 1, 1952

By Carlos Rebolledo, Nelson Parra

Arsenic is an unresolved problem in the mining industry considering the fact that most of the new copper deposits have high arsenic contents; stricter environmental restrictions for handling, transporting and processing complex materials are expected and stable abatement of arsenic is not extensively applied. In 2018 Chile produced 24.5% of the total copper from concentrates and in the future copper production in Chile is expected to increase, mainly associated with production of concentrates that will also contain more arsenic. China has set an import benchmark of maximum 0.5% for arsenic content in copper concentrates and this value is expected to be more restrictive in the future. On the first day of 2018 China banned the importation of scrap. Blending practice has been a business option, but it is not sustainable in the future, as “normal” copper concentrates become less and less clean. By the end of 2018, Chile formulated new regulations, increasing the capture of SO2 and arsenic to 95%. In order to comply with these regulations Chilean smelters had to make large invest large amounts of money. Disposing of arsenic as a stable residue is a pending issue. EcoMetales is a 100% subsidiary of Codelco and provides the mining industry with environmental solutions. It has a plant near Calama in Chile that treats flue dust from smelters, refinery effluents and acid solutions from acid plants. EcoMetales is fully committed to contributing to the solution to the arsenic problem. Currently we are developing four main projects: 1) Concentrates treatment. A PLCC project considering the treatment of 200 ktpy of copper concentrates with arsenic from the northern district of Codelco; 2) EPAS DET project considering the treatment of 700 m3/d of weak acid solution with arsenic from the of El Teniente devision of the Codelco acid plant; 3) Borras project, considering the recovery of valuable metals (Cu, Ag, Ge, Pb) from the flue dust leaching plant; 4) Tailings project, considering the recovery of metal values from tailings. The purpose of this work is to present the trends and treatment processes for arsenic handling in the copper mining industry with a focus on the scorodite process. INTRODUCTION Between 2000 and 2015 the global copper concentrates production has grown from approximately eleven to fifteen million metric tons per year. Chile produced 26.5% of the total copper from concentrates and in the future copper production in Chile is expected to increase, mainly as a result of the production of concentrates (Figure 1)

Jan 1, 2019

By K. Poorhaydari, B. M. Patchett, D. G. Ivey

In this paper, some applications of carbon extraction replicas, as samples for transmission electron microscopy (TEM), are discussed. Modern high strength microalloyed (HSMA) steels, used as structural or pipeline materials, have very small grains with substructures. Replicas used in TEM can resolve the grain boundaries and can be used for grain size measurements in cases where the small size of the grains pushes the resolution of conventional optical microscopes. The grain size variations obtained from replicas correlated very well with mechanical property variations, indicated by hardness, in the fine-grained heat-affected zone and base metal of some welded HSMA steels. Replicas are also very suitable samples for precipitate examination with analytical TEM. Advantages and limitations of the application of replicas, as well as some corrections for the estimation of the volume fraction of fine precipitates, are discussed.

Jan 1, 2005

By . A. C. Atenas

Control of arsenic in the Potrerillos' Refinery electrolyte has been obtained by withdrawing a bleed stream of circulating electrolyte and ensuring the ratio of [O]/[As] in the cast anodes is maintained between 0.9 and 1.0. In order to achieve this control the anode oxygen must be adjusted, depending on the arsenic level in the cast anodes. It has been necessary to modify the time of the reduction step in the anode furnace refining process. Control of this ratio has permitted electro refining of anodes with high levels of arsenic, up to 3000 ppm, while minimizing the volume of electrolyte that must be removed for impurity control so as not to affect the copper concentration in the electrolyte. However this control strategy is not useful when the arsenic concentration in the cast anode is too high, because it is limited by the maximum oxygen concentration allowable for a good quality anodic. Costs have been reduced in anode furnace refining because it is no longer necessary to use alkaline flux injection to remove the arsenic in cast anodes.

Jan 1, 2007

By Seungwoo Park, Whuisu Shim, Roe-Hoan Yoon, Kaiwu Huang

"A comprehensive froth model has been derived from first principles. It is based on predicting the kinetics of film thinning in the presence of particles of varying sizes and surface hydrophobicity. According to the Reynolds lubrication theory, the thinning of a horizontal film is driven by the excess film pressure (p), which is determined by the capillary pressure (pc) and the disjoining pressure (II). In the presence of particles, macroscopic capillary pressure (pc) is affected by the local capillary pressure (pc,local) in the vicinity of a particle and the number of particles in the film (N1,film), which in turn vary with the hydrophobicity and size of the particles. The Reynolds equation corrected for pc,local and N1,film is then used to predict the time (or froth height) at which a film is thinned to a critical rupture thickness (hcr), which in turn can be predicted using the Vrij’s capillary wave model (1966) after a modification to incorporate the contributions from hydrophobic disjoining pressure (IIhp). The model can predict bubble coarsening represented by the bubble size ratio between the top (d2,t) and bottom (d2,b) of a froth as functions of particle size and hydrophobicity, ? -potentials, frother dosages, froth height, gas flow rate, salt concentration, etc. The model predictions have been verified in experiments.INTRODUCTIONFroth flotation is regarded the best available technology today for upgrading minerals and coal fines. In the pulp phase of a flotation cell, air bubbles collect hydrophobic particles dispersed in it and rise to enter the froth phase on the top. Once in a froth phase, the bubbles coalesce with each other and become larger, resulting in a decreased bubble surface area. Under conditions of limited surface area, less hydrophobic particles drop off the bubble surface and return to the pulp phase. Thus, bubble coarsening provides a useful mechanism of increasing product grades. On the other hand, uncontrolled coarsening results in a decrease in bubble carrying capacity and hence throughput."

Jan 1, 2016

By M. Hozayen, Q. Ni, E. S. Radwan, P. Nawrocki, A. Jebbouri

"A major geomechanical study was conducted for one of the UAE onshore oil fields with the purpose of studying reservoir rock properties and stress distribution, based on which a 3D coupled reservoir geomechanical model was built. This model was later used for wellbore stability analysis and for analyzing the effect of fractures on future reservoir production performance, including fracture deformation and permeability evolution occurring due to reservoir depletion and resulting changes in local stress field. The subject of this study was a complex fractured Upper Cretaceous carbonate reservoir characterized by high degree of heterogeneity, both vertically and laterally. Wellbore instability related drilling problems were encountered while drilling the wells in this field. The problems were mainly in drilling the horizontal wells, including breakouts and mud losses. Experimental results of laboratory tests used in this study are summarized in Part I of this paper whereas wellbore stability analysis and formulation of a3D geomechanical model that was built for that purpose is summarized herein.A 3D geomechanical reservoir model was developed, which included natural fractures. The mechanical properties of the reservoir rock, such as Young’s modulus, Poisson’s ratio, UCS, friction angle and tensile strength were populated based on the correlations established in Part I of this paper and the developed model was then used to simulate the 3D mechanical-property distribution and the evolution of the in situ stresses in the field due to depletion from 1983 to present-day. Based on the full field model, mud weight cubes were developed to predict the safe mud weight windows in different drilling directions. In addition, well stability prediction for two planned wells was performed using a 3D near-borehole model. Firstly, the computed stress state and mechanical properties simulated in the full field model were extracted along the well trajectory of an existing horizontal well which was drilled recently and then, a3D near-borehole model was constructed along the well trajectory. The wellbore stability analysis along the well trajectory, including stress state, strain distribution and displacements, was performed to identify the instability events along the well trajectory. It has been seen that the presence of natural fractures is closely related to the recorded borehole instability incidents. The computed plastic strains which indicate the wellbore failure were consistent with the recorded wellbore instability events in the FMI image logs, what provide further verification of the developed model. Then, this 3D near-borehole model was applied to two planned horizontal wells and the wellbore stability analysis for the two wells was carried out.The results showed that drilling vertically in the reservoir is safer than drilling horizontally. However, the drilling mud weight window in the vertical direction is narrow, being as narrow as 18.7 pcf or 0.299 sg locally. Drilling horizontally is less stable towards the maximum far field stress direction than towards the minimum far field stress direction. The mud weight cubes were used to identify the optimal well placement and well trajectory. For planned well trajectories, this technology can also be used to determine the optimal mud weight."

Jan 1, 2015

By A. Singh

Two alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho have been processed by direct extrusion at 300°C and 200/230°C to produce various microstructures containing icosahedral quasicrystalline phase with different grain sizes. The alloys were mechanically tested in tension and compression. The mechanical properties were related to the grain size and microstructures studied by transmission electron microscopy. The extruded alloys showed a mixture of nano-sized icosahedral and monoclinic Mg4Zn7 phase, as well as icosahedral phase particles a few hundred nanometers in size distributed in the matrix. Coarse icosahedral phase particles several micron in size also remained after extrusion. The alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho extruded at the same temperature of 300°C produced very different grain sizes of 15 and 3 µm, respectively. The alloy Mg96.9Zn2.7Ho0.4 extruded at 200°C and Mg93Zn6Ho extruded at 230°C produced grain sizes of 0.7 µm and 1.5 µm, respectively. Both the alloys showed yield stresses of about 300 MPa in both tension and compression with elongations of about 18%. Hall-Petch parameters are calculated for the alloys.

Jan 1, 2006

By S. Fabich

Since the very beginning of Polish copper mining, special consideration of sink shaft techniques through highly saturated Cenozoic rocks was required. Shaft freezing has been chosen as a method to consolidate these rocks. Due to the rock mass structure and water inflow potential, shaft sinking without freezing was considered dangerous. In the course of time, rock mass freezing technology and experience were evolved and this technology became safer and more reliable. New techniques appeared not only in the technical method of freezing, but also in the matter of designing. Computer aided techniques allow engineers to make a detailed analysis and view of freeze wall development. Nevertheless it is important to determine basic thermal rock properties. In this paper, the evolution of knowledge and engineering experience taken in Polish copper mines and current knowledge level in that matter were shown.

Aug 1, 2013

By Burrows. A.

Temperature profiles in the lead smelter sinter bed at Xstrata Zinc Mount Isa sinter plant have been measured using a wireless temperature probe. Corresponding sinter samples have been collected for characterization. The sinter peak bed temperatures were found to be in the range of 1000 - 1200 °C. Microstructures and softening temperatures of these sinters have been characterised. Strong correlations have been observed between peak bed temperature and peak hood temperature, and between mean sinter softening temperature and peak bed temperature. It was found that higher peak bed temperature results in higher sinter softening temperature. For the feed material used in the trials, to obtain sinters with mean softening temperatures above 1050 °C, peak bed temperatures above 1130 °C are required. There appears to be a direct correlation between granule size distribution in the feed and peak bed temperature attained. High peak bed temperatures are observed in sinters with narrow granule size distribution.

Jan 1, 2008

By Hal. Oliver

MR.]. G. TRAILL: My only excuse for contributing to the discussion on Mr. Hall's interesting paper is that I had the good fortune to be employed at Noranda during those romantic years, 1927 and 1928, when construction was at its height. The mine was in course of being rapidly prepared and brought into production, and the initial difficulties in crushing-plant and smelter were being met and overcome. They were stirring days, and perhaps those members who were with the second Empire Mining and Metallurgical Congress in 1927 sensed the atmosphere of excitement and activity that prevailed. Early History. Noranda must surely possess some of the most remarkable ore-bodies known to mining men, and the story of their development is pure romance. Ed. Horne's faith in the property, and the persistence of Thomson and Chadbourne, were richly rewarded in the end, but only after some very thin times had been experienced. In those early days access to the district was by the Kenojevis river and various portages to Osisko lake, on the shores of which the mine and smelter and the town of Noranda now stand. But all the early work was done on the Chadbourne claims, more than a mile to the west; through the b~sh. I have read a log of the events of that period, and through the whole tale of hard work, discouraging developments, occasional shortages of food, and constant danger from forest fires, can be read the faith and persistence of the men in charge. The Chadbourne ore was of that well-known type which, though just too low-grade to pay (with gold at $20 per ounce), is yet sufficiently encouraging to lead one on in the hope of striking something better. It was only as a last resort that work on the Chadbourne claims was suspended and a diamond drill brought to the gossan-covered hill beside the lake. The diamond-driller told me his version (it may be exaggerated) of how the position and direction of the first hole were decided on. He was told, "You might as well set up your drill here, and drill in, say, that direction". I believe that the first hole went through the richest ore ever found at Noranda. After the drill had gone through about 150 feet of solid sulphide ore running 17 per cent copper and 4 dwt. of gold per ton, it passed into barren rock, but the diamond-driller expressed the opinion (I wonder how he knew)) that the hole would come into ore again before long.

Jan 1, 1937

By P. Nelson

Extending the campaign life of the Mitsubishi furnaces at Xstrata Copper's Kidd Metallurgical Division Copper Smelter has been a major focus of attention for many years. One aspect of this effort is real time monitoring to detect abnormal conditions and safely shut the furnaces down before significant damage occurs. Traditional real time methods of monitoring the integrity of refractory furnaces containing molten metal include alarms on individual temperatures of the refractory or cooling water. The need to set alarm limits which are not exceeded across the range of normal operating conditions leads to a system that only provides a limited warning, if any, before a failure occurs. Integrity monitoring systems that look at many different signals and alarm only changes in the relationships between the signals have been implemented on the smelting and converting furnaces. The systems are based on principle components analysis (PCA) models and implemented with the monitorMV software package. These provide much more sensitive and selective alarms so that changes in integrity are alarmed well in advance of any event. At a critical alarm level, the converting furnace is set to automatically shut down so that operating and technical personnel can review the situation. The configuration of the systems and operating experience with them will be discussed.

Jan 1, 2007