Search Documents

By R. Lasmanis, W. C. Utterback

"The Mount Tolman porphyry Mo-Cu deposit is 64 km south of Republic, Ferry County, Washington. It occurs in the composite Keller Butte pluton, which consists of the Keller Butte porphyritic biotite granite and granodiorite, the Mount Tolman quartz porphyry granite, and the Meadow Creek biotite granite phases. The three phases range in age from 61.3 Ma ± 2.3 Ma to 55.7 Ma ±2.0 Ma. The stockwork deposit occurs in the Keller Butte phase above the contact with the Mount Tolman quartz porphyry granite.Mount Tolman is a hybrid calc-alkaline deposit that has features of both a Climax-type and a plutonic type. Prior to post-ore faulting, the deposit had a flattened hood like shape. In plan it is elongated- 1.6 km wide, 3.2 km long, and up to 609 m thick. The orebody has a 292 o strike. It contains a geologic reserve exceeding 2.18 billion tonnes of ore averaging 0.093% MoS2 and 0.09o/o Cu using a 0.048% MoS2 cutoff. Of this total, 816 million tonnes of measured and indicated ore averaging 0.097% MoS2 and 0.09o/o Cu could be mined by open pit with an overall waste-to-ore ratio of 0.91 to 1.The deposit is a stockwork of quartz and quartz-sericite-pyrite veins and fracture fillings that contain molybdenite, chalcopyrite, sphalerite, and magnetite. Five separate episodes of fracturing and mineralization produced the orebody and were followed by four additional episodes of fracturing with sulrgrade mineralization. The Mount Tolman deposit contains propylitic, argillic, phyllic, topaz greisen, and potassic alteration zones. Extensive silicification overlaps the K-feldspathized, quartz-topaz, and phyllic alteration zones."

Jan 1, 1995

By Antonius Prayoga

PT Smelting adopted the Mitsubishi Continuous Technology for its copper smelter plant which has been operating since 1998. Through a series of expansion projects, the plant annual production capacity increased gradually from 200,000 to 300,000 tons of copper. There were no significant modifications for the smelter to reach the 50% additional capacity. It was mostly achieved by intensifying the operation of the furnaces by increasing the oxygen content in the furnaces blowing air. Intensive smelting furnace operation caused shorter campaign life of some furnace refractory, especially the melt zone wall on furnace outlet. During each furnace relining, which is done once every two years, severe wall erosion was found. The worst condition occurred in 2007 when the smelting furnace experienced a melt leak through the eroded wall beneath the bath-line coolers. During the 2008 furnace relining, a modification was performed by installing vertical coolers behind the melt zone wall. Additional vertical coolers were installed during the 2012 furnace relining to extend the coverage area. The modification improved melt zone wall integrity significantly by keeping them safely within the two year campaign life. Recently a modeling study was done to estimate the influences of molten waves on furnace wall erosion. The aim of the study was to predict the impact of blowing parameters, such as blowing air velocity, on the melt wave character and wall erosion.

Jan 1, 2015

Introduction A Hypothetical Scenario: Suppose that your company's research department has developed a new device which represents a significant innovation. You would like to begin selling it as soon as possible. The new device has not been publicly disclosed. You're not sure about what type of intellectual property protection you should be seeking, or when you should be seeking it. As discussed below, assuming that the costs are worth it, a patent application probably should be filed before any public disclosure is made. In general, if you do not file a patent application prior to a public disclosure, you will lose rights. Major Types of Intellectual Property In this paper, intellectual property protection is broadly discussed. Practical steps which can be taken to minimize the possibility of losing intellectual property rights (and maximizing the possibility of benefiting from your company's intellectual property) are outlined at the end of this paper. The issues discussed in this paper are somewhat complex, because a number of outcomes are possible, depending on the facts. It is strongly recommended that you seek legal advice in your jurisdiction in connection with any particular circumstances relating to intellectual property rights. "Intellectual property" refers to a number of different types of rights. The major types of intellectual property are: (i) patents; (ii) trademarks; and (iii) copyright. Trade secrets are also usually considered to be a type of intellectual property, and they are also discussed in this paper because of their importance. In general, each of these types of intellectual property protects different subject matter, although there can be some overlap. Intellectual property rights are generally territorial in nature. The scope of protection of a type of intellectual property in a country (e.g., patent protection) depends on whether the specific national requirements for protection have been met.

Feb 1, 2008

CFD (Computational Fluid Dynamic) models have been developed and validated for a pulsed column with disk-doughnut internals, as used for solvent extraction. First a single phase model was developed to simulate the turbulent oscillating flow around the internals of the column. This model was successfully validated using detailed PIV measurements of velocity taken at eight different phases through the pulse cycle. Second, the CFD model was extended to allow for a continuous aqueous phase and a dispersed organic phase (kerosene) flowing counter-currently. The model was a two-fluid model that accounts for droplet breakup and coalescence, and solves for droplet size distribution using a population balance model incorporated into the CFX4 package. PDIA (Particle Droplet Image Analysis) measurements were taken on a pilot scale solvent extraction pulsed column to determine droplet size distribution for calibration and validation of the CFD model. The measurements were made under pulsing intensities ranging from 10 mm/s to 32.5 mm/s.

Jan 1, 2007

By R. W. Pauls

"Many tens of thousands of hectares of forested land will be disturbed and reclaimed in the surface mineable Athabasca oil sands area during the next few decades. The surface area disturbed by Syncrude’s Mildred Lake development alone exceeds 10 000 ha to date. It is not clear that reforestation of disturbed areas will best accommodate the aspirations of all stakeholders, particularly traditional users of the land. A five-year research program by Syncrude Canada Limited and the Fort McKay First Nations has examined the feasibility of raising bison on land reclaimed after disturbance by oil sands development. Forage productivity and carrying capacity for bison was comparable to that of grasslands elsewhere in Alberta. Concerns regarding compaction of newly rebuilt soil by bison traffic proved unfounded. Bison demonstrated weight gains typical for ranched bison and calving rates averaged 90%, a value typical for ranched bison. The animal husbandry problems encountered were typical of those occurring on bison ranches elsewhere in Alberta. An economic analysis indicates that a 1000 ha bison ranch on reclaimed land has a net present value that compares very favourably with a similar area supporting commercial forest. Subject to approval by Alberta Environmental Protection, the current research project will be expanded as a pilot commercial ranching venture in order to explore its commercial viability as a business venture by the Fort McKay First Nations. At the same time, measures will be implemented to resolve various regulatory issues associated with commercial bison production in the oil sands area.BackgroundSyncrude Canada Ltd. (Syncrude) is proposing, in its land reclamation strategy, a feature that is, depending on one’s background and perspective, regarded as an innovative approach to land reclamation, a threat to the regional forest industry, a creative response to aboriginal stakeholder concerns, a reneging on reclamation commitments, an opportunity to provide an ongoing economic base for postoil sands regional economy, or an environmentally unsound use of the land. These diverse and sometimes strong reactions have been generated by the proposal to introduce bison, either free-ranging or commercial ranched, to the reclaimed landscape."

Jan 1, 1999

By Victor F. Hollister

Elemental sulphur occurs as aformational sedimentary deposit in Upper Devonian Wabamun evaporites near Coronation, Alberta. The deposit developed in a stratigraphic jacies-change lrap; it is assumed that petroleum reacted with anhydrite to form sulphur, calcite, hydrogen sulphide and other reaction products. The deposit contains about 362,800 tonnes of sulphur and lies at a depth of 1200 m. The Coronation deposit is expected to be geologically typical of such other native sulphur deposits as may be found in Wabamun Group sediments. Widespread sour gas sulphur production f rom the Wabamun suggests the possibility that additional native sulphur deposits will ·be found.

Jan 1, 1984

By I. M. M. W. R. Jones

"THE OBJECT of these notes is to initiate a discussion among the members of our Institution on the connotation of the term 'ore', and to arrive, if possible, at an acceptable definition of the term in the light of its current use by our leading mining engineers, metallurgists, •and geologists.The majority of •authors of well-known modern text-books on subjects dealing with mineral deposits define 'ore' in words which convey the meaning that it is an aggregate of minerals from which one or more metals can, under favourable conditions, be extracted profitably.Many eminent members of the Institution, and of mining and metallurgical institutions in other countries, consider that the term should not be restricted to metalliferous mineral •deposits but can also be applied correctly to certain non-metallic deposits. They believe that the growth, during the twentieth century, in the industrial importance of non-metallic minerals, and the progress made in the mining and the milling of deposits containing such minerals by methods similar to those used for metalliferous mineral deposits, no longer justify the academic restriction of the term to deposits worked for their metal content only."

Jan 1, 1954

By J. Hedderson, J. Starkey, S. Reeves, B. Hilscher

"As ore sorting becomes more common, it is important to quantify its impact on comminution circuits in order to precisely predict its effect on throughput, grind, and mill operating conditions. Since sulphides and other valuable minerals are often softer then the surrounding waste rock, the ore kept by a sorting system is typically softer than the average ore. In order to accurately forecast production, new measurements of hardness need to be performed on the new concentrated mill feed. This paper proposes a methodology to examine this effect quantitatively at an early stage of project development using the SAGDesign test.INTRODUCTION The application of ore sorting in the mining industry is one of the most promising recent technologies with the potential to cause step change in the way concentrators are designed. Most typically, ore sorters are used to sort a given ore flow for grade, either to reject waste from the mill feed, or rescue ore from the waste pile. Ore sorting technologies have been successfully applied at many mining properties in various forms and while the technology has reached or is reaching maturity in other industries, it is still in development in the mining sector. As a result, there is not yet a general consensus on the considerations that need to be made when designing a plant with ore sorting from a feasibility level above and beyond what is commonly performed as best practice. This paper will discuss those considerations and propose a methodology for integrating ore sorting into a comminution circuit at the design phase. Due to the linearly additive nature of the SAGDesign Test results, a “hardness balance” can be developed to estimate the ore hardness which would be measured in any sorting mass split using only two data points. This will allow a design engineer to make more informed decisions as to the most appropriate mass split to select in relation to the incurred operating costs and grinding circuit sizing."

Jan 1, 2019

By M. Hardy

"The structural design of mine headframes is challenging due to the significant differences in the geometry, rigidity, and behaviour of these structures compared to conventional buildings. The differences are related to the main purpose of these structures, which is not human occupancy, but rather the support of hoisting equipment. The main objective of this paper is to present the seismic elastic behaviour of headframe structures in comparison with conventional buildings, which is the base case for the definition of seismic loads. This paper highlights the impact of backlegs on the dynamic behaviour of mine headframes, more specifically the resulting torsional sensitivity. INTRODUCTION The design of industrial structures is often governed by industrial processes rather than by architectural constraints. In ground-mounted hoisting plants, the structural configuration of headframes must allow clearances around conveyances and ropes while resisting the lateral loads associated with the hoisting equipment. Typically, these structures use backlegs to withstand the lateral loads, which leads to highly irregular structures with unconventional dynamic behaviour. The codes and standards applicable to the structural design of mine headframes in Canada are often incomplete or not adapted to the reality of practising engineers. This situation creates confusion, and engineers must look at various guidelines and international standards to support the engineering calculations required for the design of these structures. The loads resulting from the support of hoisting equipment, such as ropes and conveyances, are usually simple to calculate and are determined based on the information from manufacturer and industry related guidelines. Moreover, the loads associated with snow accumulation and wind are calculated applying the same methodology used for conventional buildings, without any major issues. On the other hand, the seismic loads are often difficult to calculate based on the methodology from the National Building Code of Canada due to the significant differences in the dynamic behaviour of the structures. The resulting structures may be either over-designed or worse, under-designed. Hence, there is a lack of uniformity in engineers’ designs. The latest edition of CSA S16-14 “Design of steel structures” includes Annex M (Informative) “Seismic design of industrial steel structures” to help designers close the gap between the requirements of traditional regulations and actual engineering practice."

Jan 1, 2019

By R. Carter, C. S. Samis

"SummaryThe results of this investigation indicate that the gold in the cyanide tailing of refractory gold cyanides is occluded in fused •particles formed during roasting. This conclusion was reached following microscopic examination of calcines produced at various furnace temperatures with different atmospheres, and a •comparison with calcines produced by decomposing samples of completely sulphated concentrate under conditions such that the maximum particle temperature varied between 6•50°C. and 1,100°C. This comparison showed that the particle temperature during a normal roast may be several hundred degrees higher than the furnace atmosphere, or that the fusion is associated with a low melting (950°C.) eutectic mixture of FeO and FeS.Because of the unavoidable particle fusion during a furnace roast, and because low particle temperatures are essential for gold extraction by cyanidation, aqueous medium oxidation under high oxygen pressures was studied. Gold recovery from calcines produced by this means was over 98 •per cent •compared with a maximum of 80 per cent from furnace calcines.IntroductionMANY arsenical gold ores are called 'refractory' because much ' of the gold cannot be satisfactorily extracted by cyaniding the raw ore or concentrate. Even when such ores are roasted to oxidize .the iron and arsenic and 'release' the gold, often 10 to 25 per cent of the gold present is lost in the cyanide residues."

Jan 1, 1952

By S. P. Jekielek

"This paper describes the automation of a mine hoist ore loading pocket using a programmable controller. It provides an introduction to programmable control, and outlines the various modes and operating sequences of the loading pocket. A comparison is made with previous equipment to illustrate the increased flexibility, reliability and diagnostic functions that are gained.IntroductionLoading pockets have evolved from a couple of manually operated air cylinders to entirely automated systems. Early pockets were usually formed in rock, with loading and discharging regulated by air-operated gate s. Interlocks, added to this arrangement, prevented simultaneous operation of the gates and ensured proper hoist position . As the loading pocket advanced, it was recognized that gravity feed posed problems, often becoming plugged or letting water run through into the shaft. A belt conveyor was employed, eliminating the se problems and resulting in greater loading control. Weighing the combination of transistorized logic modules, replaced many relay systems. This elimination of moving parts and contacts increased reliability and reduced maintenance costs.As semiconductor technology progressed, there were major breakthroughs in miniaturization and reliability, and as a result the programmable controller was introduced. Programmable controllers first appeared in the automotive industry in the late 1960's. A system controller was required to replace the large relay panels in operation at that time. The use of digital integrated circuitry enabled these programmable controllers to automate processes with hundreds of inputs and outputs. Advances in electronics reduced production costs , making controllers for smaller application s viable . This development is on-going, each generation introducing controllers with greater capabilities for a wider variety of systems. equipment was the next step in loading pocket development, and dependance on much of the manual control was reduced . The complete system was first automated using relay panels. Solid- state devices were later introduced, and static control,"

Jan 1, 1980

By E. Allen

Quebec Cartier Mining Company operates approximately two hundred and fifty pieces of equipment in a climate with a temperature that has averaged 27.5°F during the last seven years. The use of special-purpose lubricants, fuels, antifreeze, rubber compounds, and alloy steels have reduced the cold-weather hazards. In some areas, high-cost cold-weather protective heating devices are being eliminated with experience.

Jan 1, 1966

By Kish. L.

"The results of a chemical and mineralogical study of eighteen opaque-oxide occurrences are discussed and the detailed chemical, metallurgical and mining feasibility study of a vanadium-rich magnetite deposit is summarized. A plot of the mol-percentages in the system FeO- Fe2O 3-TiO2 indicates that the deposits fall into two distinct groups: some contain hematite with ilmenite, and some others have magnetite with ilmenite (titaniferous magnetites). The plot also suggests that the two types of deposits were crystallized from liquids of different compositions. Each group has its distinct structural features. Vanadium is present in all of the studied specimens, however concentrations of economic importance have so far been found only in the titaniferous magnetite deposits. The vanadium content of the oxide concentrations of the Dore Lake Complex is the largest among the studied occurrences. Analyses of the concentrates of the drill-core sections show a compositional variation across the orebody; a continuous increase in the tenor of Ti02 and a decrease in the vanadium content upward in the layered sequence is found. Concentration tests on several tons of samples indicate that about 80 per cent of the vanadium is recovered in the magnetite concentrate."

Jan 1, 1972

By Suman Giri

Non-Intrusive Load Monitoring (NILM) is a method of extracting appliance-level power consumption information from aggregate circuit-level data with the goal of giving users feedback regarding their energy consumption so they can take control of their consumption habits. In this paper, we present a novel algorithm for classification of on and off states of appliances. We compare the performance of our algorithm in on state detection with a pervious paper that evaluated the same dataset and show that it performs up to 13% better. We also present the results of a case study where we collected data for different modes of a cooktop, microwave and dishwasher and used our algorithms to perform power estimation. The error on ten different setups in the test bed ranges from 1% to 32%. We discuss our results and lay out ideas for future work.

Aug 1, 2013

By John R. Morgan, Peter Graham

"Onakawana Development Ltd. and Mana/ta Coal Ltd. have completed feasibility studies on a large lignite deposit located in the James Bay lowlands of northeastern Ontario. The mining plan described in this paper would supply coal for approximately a 33-year period with peak production in the early years of approximately 6.5 million tonnes per year then declining to 1.2 million tonnes in year 33. This paper describes the geology, resources, lignite quality, mine planning and related topics. LocationThe Onakawana lignite deposit is located in northeastern Ontario in the James Bay lowlands (Fig. l). The Ontario Northland Railway crosses the property and links it to Moosonee, JOO km further north, and Cochrane 180 km south. The area is crossed by latitude 50° 37', the approximate latitude of Calgary. Toronto lies 800 km south of the study area. History of Development The deposit has been known since the late 1600s when early English settlers extracted limited amounts of lignite for use at Moose Factory. The deposit has undergone sporadic periods of exploration activity in the late 1920s and early 1930s when the Ontario government drilled 116 holes, sunk two exploration shafts and published several technical and economic studies. Interest in the property was reactivated from 1939 to 1945 when the Timiskaming and Northern Ontario Railway Ltd. drilled 182 additional closely spaced holes, excavated a test pit adjacent to the rail line and installed a boiler for testing purposes. In 1965, Alberta Coal Ltd., the predecessor of Manalta Coal Ltd., first became involved. Since then a further 182 holes have been drilled and coied, and the existing test pit reopened for sampling. In 1980, various reassessment studies were launched, including geology, mine engineering, conceptual design and environmental assessment studies. The following discussions have been drawn extensively from these reports."

Jan 1, 1985

By M. M. Williams

ALBERTA has been generously endowed with oil, natural gas, coal and water power, thus giving power producers a wide choice in the type of plant and fuel which can be used. Therefore, with such a variety of energy sources to choose from, why was coal selected as the primary fuel at Calgary Power's Wabamun steam plant? This part of the paper will cover the circumstances that led the Company to decide in favour of coal. The second part, to be presented by C. F. Doerr, will describe how the Wabamun coal mine has been developed to supply the large fuel requirements of the power plant. Before considering the Wabamun plant, we require a general under-standing of? the Company's electric system and load. Power is fed into a 5,100-mile high-voltage transmission grid from eleven hydroelectric plants and from the Wabamun steam electric plant. These plants have a combined generating capacity of 820,000 horse-power. Of this total, the hydro

Jan 1, 1963

By S. Sopher, C. Barsotti

"Inco Gold Company was created in 1987 as an unincorporated business unit of Inco Limited. In 1988, Inco Gold Management Inc. was incorporated to supply management, exploration and engineering services to this unit. The first new project, at Casa Berardi, Quebec, was brought to production in September 1988, less than two years after completion of exploration. For 1989, Inco Gold's exploration and capital expenditures have been budgeted at approximately $94 million, a record level. Inco Gold holds interests in more than 80 precious metals ventures and prospects in Canada, the United States, Brazil, Indonesia, Papua New Guinea and France. The most advanced projects, in addition to Casa Berardi, are at Mineral Hill, Jardine, Montana, where initial production is anticipated in the third quarter of1989, and Crixas in central Brazil, where production is scheduled to begin during the fourth quarter of the same year.BackgroundTraditionally, Inco Limited's mineral exploration has concentrated on nickel and other base metals but since the early 1980s Inco's exploration activity has focussed strongly on precious metals, principally gold. As a result, three deposits have been discovered and developed . In order to accelerate the establishment of a strong gold mining enterprise with its own specific growth and profit objectives, Inco Gold Company was created in 1987 as an unincorporated business unit. At the end of 1988 Inco Gold's share of drill-indicated gold reserves was approximately 14 million short tons containing 3.4 million ounces of gold.At Casa Berardi in northwestern Quebec, one mine is in production and another is planned to open in 1990. Properties at Crixas in Brazil and at Jardine, Montana, U.S.A., were being readied for production in 1989. By 1991, Inco Gold's share of gold production is expected to be 125 000 ounces with a target of 400 000 ounces annually by the mid-1990s."

Jan 1, 1990

By V. Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modelling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioning of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

Apr 1, 2004

By J. F. Henderson

Stable mining operations commenced in the Northwest Territories in 1933. Pitchblende from Great Bear lake and gold from the Yellowknife district are the main minerals produced. The value of pitchblende products produced from 1933 to 1941 was nearly $6; 000; 000; data on subsequent production are not available. The first gold was produced from the Con mine at Yellowknife in 1938. Other properties that later came into production include the Negus; Slave Lake; Thompson Lundmark; and Ptarmigan mines. The annual gold production reached $3; 862; 000 in 1942 but due to the war and consequent labour shortage fell to $333; 218 in 1945. The only producing mines at present (May; 1947) are the Con and Negus; but several promising properties are under development; including that of Giant Yellowknife Gold Mines where large tonnages of ore are being blocked out. With the reopening of former producing mines and new production from properties now being developed; gold production should rapidly increase and exceed its former peak within the next few years.

Jan 1, 1954

By S. Ross, M. Mayhew

"Kirkland Lake Gold introduced battery equipped vehicles (BEVs) at the Macassa Mine in 2011. The fleet of underground BEV haulage trucks and loaders has grown over the years to over 30 units, the world’s largest, currently handling approximately 80% of the daily production tonnage. The inflow and outflow of air occur through a limited number of relatively small openings, which limits the air volume delivered to the underground workings. In addition to improving air quality, the reduced heat load generated by the BEV (when compared to diesel equipment) had a significant positive impact in the workplace. The use of BEV for material handling has enabled increases in production that would not have been possible using diesel equipment.INTRODUCTIONMacassa mine was developed as a track-drift access mine, with the most recent shaft (#3) sunk in 1986. A new mining complex, the South Mine Complex (SMC) was discovered below the 5025 foot elevation south of traditional mining areas, and the majority of mining now occurs in the SMC. The discovery of that zone has led to an internal ramp which is used to access the SMC and haul ore to #3 shaft.The amount of airflow that can be moved through the mine is limited by the existing infrastructure to surface. This amount was recently increased to near its practical maximum from 118 CMS (250 kCFM) to 151 CMS (320 kCFM).Both diesel and electric equipment are used at Macassa. Tethered Load-Haul-Dump Machines (LHDs) have been replaced with Battery Electric LHDs, due to their increased mobility and depth of the mine. Battery trucks continue to replace locomotives to transport both ore and waste to the shaft, as mining has transitioned from tracked levels to trackless level and haulage has transitioned from horizontal levels to an inclined ramp.EQUIPMENT FLEET AT MACASSAMost of the primary material movers utilized at Macassa Mine are battery operated. As the mine goes deeper the battery technology will continue to be critical to the success of the operations. With over 300,000 hours of proven operation success, the battery technology and equipment will continue to be a major part of Macassa’s future."

Jan 1, 2019