Search Documents

By D. Saramak, Z. Naziemiec

"Chalcedonite is an unique rock due to the relatively small area of its occurrence. It also possesses multi-raw-material features therefore it should be given a special protection aiming at its complete and optimal utilization. It is the natural sedimentary rock and the only mine in Poland, located in Inowlodz, where the opencast mining from “Teofilow” deposit is carried out.Chalcedonite mainly consists of cryptocrystalline and microcrystalline chalcedony together with small amounts of autogenous and detrital quartz. The chalcedony itself is a fairy common mineral and many forms of its occurrence is known, some of them are semi-precious minerals. Among the most popular ones following can be found: agate, bloodstone, onyx, carnelian, chrysoprase. Many countries own chalcedony deposits: Australia, Brazil, India, Canada, Namibia Russia, South Africa. However chalcedony in its pure form does not occur in the mentioned chalcedonite rock. The pores, which take usually from 5% to 25% of volume and have sizes smaller than 0.5 mm, are the characteristic feature of all chalcedonite forms. The paper presents some crucial problems of its processing together with most significant directions of its applications. New method of chalcedonite enrichment based on densimetric separation (patented in Poland) is presented. Results of investigation show that the obtained products can increase quality of concrete and filter grits."

Jan 1, 2016

By P. I. Laforest, M. S. Moats

"Antimony in smelted copper anodes has been shown to cause problems in electrorefining including brittleness of starter sheets. In order to improve deposit properties, a study was conducted examining the effect of anode chemistry on cathode ductility and electrolyte chemistry. Two industrial anodes with different molar ratios of As/(Sb+Bi) were used in laboratory electrorefining experiments with commercial electrolyte, and the addition of commercial glue and Avitone. The ductility of 21-hr copper deposits was evaluated by a 180° bend test. X-ray diffraction (XRD) and metallography were performed on unbent specimens to characterize the deposit structure. Increasing the anode As/(Sb+Bi) molar ratio from 0.54 to 3.8 resulted in an increase, on average, from four to eight bends to failure in cathode material produced. Significantly lower concentration of antimony (V) in the electrolyte was detected when operating with the higher molar ratio anode. The presence of (111) and (200) planes was noted in cathode material produced from the higher molar ratio anode suggesting that mixed growth character could be responsible for the observed increase in bend test results. The ductility of the starter sheet materials was improved by a higher anode molar ratio.INTRODUCTIONThe presence of antimony in copper electrorefining electrolyte has been reported to cause problems in cathode production (Hiskey, 2012; Peng, Zheng & Chen, 2012; Wang, Chen, Zhou-Lan & Lian-Sheng, 2006; Wang, Chen, Zhou-Lan, Wang, Xiao & Zhang, 2010; Wang, Chen, Zhou-Lan, Wang, Xiao & Tang, 2011; Wesstrom, 2014). To better understand the impact of antimony, laboratory scale electrorefining experiments were conducted using industrial inputs (anodes, cathodes and electrolyte). The influences of anode chemistry on the valences of antimony and arsenic in the electrolyte were monitored and correlated to physical cathode characteristics, such as a bend test to failure and crystallographic orientation.Commercially, starter sheets are produced by electrorefining impure cast copper anodes onto titanium blanks. The starter sheets are then hung in an electrorefining or electrowinning cell using loops of bent starter sheet material. These loops, in the absence of sufficient ductility, fail resulting in cathodes falling into the electrolysis cells. It is thought that the reduction in ductility can be related to anode composition; in particular, the molar ratio of arsenic to antimony plus bismuth As/(Sb+Bi). It has been stated that maintaining this ratio above 2:1 results in numerous improvements to electrorefining operations (Baltazar, Claessens & Thiriar, 1987; Kamath, Mitra, Radhakrishnan & Shetty, 2003; Krusmark, Young & Faro, 1995; Noguchi, Itoh & Nakamura, 1995; Wenzl, 2008)."

Jan 1, 2016

By E. Sigal

Overview ?Intrinsik has completed several wide area HHRA and ERA studies of mining and smelting communities ?Several ?Lessons Learned? ?Key areas related to: ?Study Design ?Data Quality ?Bioaccessibility ?Speciation ?Weight-of-Evidence Approaches ?Advances in Ecological Risk Assessment Techniques

May 1, 2009

By Patrick J. Williams

Outline -An Australian View On: ?IOCG defining features and occurrence ?Variable exploration characteristics ?Extracting value (gold metallurgy) ?Recent exploration experience(case study)

Apr 1, 2005

By Carlos Antônio de Morais, Renata Dias Abreu

The present work describes a study of the separation of terbium and dysprosium from heavy RE concentrate through a solvent extraction circuit in a counter-current system. As the efficiency of the REE extraction by acid extractants rises with the increase of the atomic number of the element, the aim of this work is to extract the elements with higher atomic number maintaining Tb and Dy in the aqueous phase. Thus, terbium was separated first with subsequent separation of dysprosium. The experiments were carried out by using IONQUEST®801 as the extractant and a REE-hydrochloric liquor as feed solution. The optimum operational circuit in terbium separation was comprised of 37 stages: extraction, scrubbing, stripping, and solvent washing. For the dysprosium separation 39 stages were required. Terbium separation over 92% with over 95% purity and a Dy separation over 97% with over 95% purity were obtained.

Jan 1, 2014

By Tony Lipiec, Ian Orford

"A key part of plant design is the selection of the design tonnage which is the hourly tonnage target that the equipment selection is based on. Its selection is critical for ensuring that the nominal tonnage which is critical to the financial performance of the project will be met. With deposits being developed at lower grades, higher tonnages and a higher degree of hardness variability, it is essential to ensure that the design process selects the comminution equipment which will be able to deal with the impact of this ore quality variation.Ore hardness and its variance are key factors to be taken into consideration for the selection of the design tonnage. It is well accepted that for the nominal or name plate tonnage to be consistently achieved, it is necessary to base the design tonnage on a hardness value greater than the average ore hardness of the deposit to be mined. The question is how much greater should this design value be to ensure that the nominal tonnage is met to the satisfaction of the project financial model. Standard industry practice is to set the design tonnage by:1. Select an ore hardness percentile that is greater than the average ore hardness to be the basis of the nominal tonnage. Typically either the 75th or 80th percentile value from the data set will be selected.2. Selection of a design factor to multiply by for determining the design tonnage, i.e. the design tonnage = tonnage (based on the average ore hardness) multiplied by design factor.This paper discusses the selection of the design ore hardness through the use of modelling or the use of a design factor. It further shows the impact of ore hardness variance on the capacity of the process and its ability to meet the nominal tonnage. Insight is provided as to what ore hardness percentile value should be selected balancing the shortfalls of tonnage for ores harder than the design value versus the above target production achieved for ores softer than the design ore hardness."

Jan 1, 2016

By Karim Ramji

The extractive sector today faces growing social, legal and political risks (SLPs) from so many different stakeholders including national and local governments, name and shame groups, civil society and environmental groups, and the ?Occupy? movement. Beyond these stakeholders, there are the indigenous peoples who have growing legal, social, political and economic influence which can often determine the outcome of the Project. The development curve in the extractive sector from initial exploration to mine start-up has become longer, steeper and more risky and expensive as these SLPs have grown in scope and complexity. Even if a project is permitted or starts commercial production, its ongoing development and operations are also facing these SLPs. The continuous assessment of these SLPs and the strategy to mitigate for them has now become critical for every project in the extractive sector. A project will only be successful if it is able to obtain the legal permits to operate, then withstand any judicial reviews, and then also to be able to gain and maintain the Social License to Operate (SLO). Stakeholder identification, management and engagement are key risk-mitigation tools. This paper focuses on the growing influence that indigenous peoples are now enjoying and the impacts on the extractive sector. Indigenous peoples are a unique stakeholder group because their legal rights and interests to lands and resources, their aboriginal title and rights, are gaining more recognition. When indigenous peoples form alliances with other stakeholders, this simply adds to their growing momentum and leverage, and this can become a daunting challenge for the extractive sector. More due diligence is required by companies to understand and assess the challenges posed by operating in areas claimed by indigenous peoples. There is a real need for mining companies to develop an effective indigenous engagement strategy to address these challenges in order to successfully convert risks into opportunities. Early identification and engagement with the indigenous peoples is required and the goal should be to conclude an Impact Benefits Agreement (IBA) with the affected indigenous peoples. The real objective must be to develop a real and transparent relationship between the company and the indigenous peoples so as to gain and maintain the SLO.

Aug 1, 2013

By Simon C. Dominy, Patrick R. Stephenson, Alwyn E. Annels

Abstract - The often complex, erratic, and localized nature of gold is a common feature of many vein-style gold deposits. This style of mineralization is often referred to as being nuggety or possessing a high-nugget effect. As a result of these complexities resource estimation is difficult and in general, only Exploration Results can be provided or an Inferred Mineral Resource estimated from surface drilling data alone. Underground development, further drilling, and probably bulk sampling will be required to delineate Indicated and Measured Resources. Tonnages can generally be estimated from diamond drill and development information with a reasonable degree of confidence. Grade is much more difficult to define with confidence because it is commonly highly erratic and discontinuous in nature. The dependency of higher confidence Resource categories on development information may create a Catch 22 situation, with funding for such development often depending on the prior definition of at least Indicated Resources. There are no easy solutions to these challenges posed by high-nugget effect deposits, and it is important when classifying and reporting not to downplay the uncertainties often associated with Mineral Resource and Ore Reserve estimates for such deposits. However, in common with all deposit types, if the principles that underpin the estimation, classification, and reporting procedures are borne in mind and common sense applied, most issues can be satisfactorily resolved. This paper discusses the classification and reporting of Mineral Resources for high-nugget effect gold vein deposits within the framework of the JORC Code (JORC, 1999).

Jan 1, 2001

By Arthur Lieu

The mill effluent treatment circuit (Bulk Neutralization (BN)) in the Cameco Key Lake Operation was modified in 2008 to enhance the removal efficiency of selenium (Se) and molybdenum (Mo) from the mill process water. This modification was completed in part due to increased knowledge of the effects these elements have on biota. In addition, legacy effects from the historical operation of the Key Lake mill in regards to Se and Mo were shown to have an effect on the regional biota in the downstream receptors. This was a challenging initiative as there was no off the shelf technology available and the removal process had to be incorporated into an existing (brownfield) process. These modifications have resulted in significant reduction in the concentration of these elements in the Key Lake mill effluent. The removal efficiency for Se and Mo in the modified circuit has increased to 95% and 75%. As a result, concentrations of Se and Mo are now consistently less than 0.4 mg/l and 0.02 mg/l. In addition, the Se and Mo precipitates formed were extensively studied to ensure long-term geochemical stability in the Key Lake in-pit tailings facility. This presentation will provide additional detail on the hydrometallurgical removal mechanisms and process modifications required in the Key Lake BN circuit to remove these elements to trace levels.

Aug 1, 2010

By Jr. Wilkinson

Suncor Energy currently mines approximately nine hundred thousand tonnes of ore and waste per day at its open pit operations in the Athabasca Oilsands near Fort McMurray, Alberta. Modeling these deposits for planning purposes is particularly challenging given the characteristics associated with the deposit - stratigraphic deposition coupled with gradational grade distribution. The identification of ore and waste is a combination of bitumen cutoff grade, minimum mining thickness and separable waste thickness subject to criteria established by provincial regulatory agencies. Suncor along with Mincom Inc. have collaborated on this project to derive a methodology, automated by computer software, to streamline the ore and waste identification process. This paper explains the methodology and programs created to identify ore and waste in use at Suncor Energy and how this identification is used to categorize reserves and to generate mine design surfaces.

Apr 1, 2005

By Andrew Bamber

Outline ?Background to Mine-Mill Research at UBC ?Mine Mill Integration ?In situ mining methods ?Underground Pre-concentration ?System Design and Supporting Technologies ?Case Studies: ?INCO -McCreedyEast Mine ?Placer Dome ?Porcupine JV ISL Study ?Musselwhite, South Deep ?Falconbridge ?Fraser Copper ?Thayer Lindsley ?Wayside Gold, other scoping studies? ?System Designs ?Summary ?Future work ?Conclusion

May 1, 2006

By D. L. Millar

The hydraulic air compressor (HAC) is driven only by water, held up by a dam, to create relatively low head (typically 10-20 metres), such that the developed hydropower is used to cause flow in openings deeper underground. Air is entrained in the water at the inlet to the sub-surface openings (an air to water volume ratio of 1:1 is reported to be optimal) and is compressed as it is carried along by the deepening water flow. At depth, and with lower water velocities arising from larger cross sectional area tunnels, air bubbles separate out of the water flow and are collected in a receiver space above the flowing water. Water, free of air, then passes back up a return shaft (up-pipe) and rejoins the river or stream flow. In principle, an HAC can produce any pressure and flow rate required, given large enough shafts and enough water supply with head sufficient to overcome frictional resistance in the sub-surface tunnels. Practically, as air solubility in water increases with pressure, HAC installations with depths greater than 100 metres may lead to higher rates of compressed air loss, without special separation measures. A modern HAC application for mine refrigeration and cooling is presented.

Aug 1, 2013

By R. Binning

"Economic high density mineral reclamation and subsequent transportation of solids through a pipeline presents many formidable engineering problems.Mineral reclamation system design by theoretical formulas is almost impossible because solids composition, ie. concentration, velocity, moisture content, solid size, etc. can only be controlled within a broad pumping range.Traditionally this has restricted pumping to relatively dilute slurries whereas it is usually preferred, because of economic considerations to reclaim as high a concentration as possible.At Toyo/De-Velde Corp. we recognized these pumping limitations and began to develop and manufacture a range of standard and auxiliary equipment that would exceed these technical restrictions.MATERIAL RECLAMATION & PIPELINE INJECTIONTo minimize fluid usage and increase material reclamation efficiency we designed a submersible dredge mixing pump that uses most of its energy to pick up material from rest, mix it with fluid into a highly concentrated slurry then push it firmly into a pipeline.Where material is too compacted to be mined by the standard submersible mixer pump, auxiliary high torque self contained submersible excavators can be fitted around the periphery of the mixer pump. This is to facilitate excavation and break up of the compacted material into a slurry.High flexibility of this system can be achieved by combining the many equipment variations available into the most efficient format to fit individual site requirements.Whatever combination of equipment is selected, torque is nullified by counter rotating excavators against each other. This increases effective excavator/material bite torque but also allows mixer/excavator rig suspension by cable for deep water material recovery."

Jan 1, 1985

By F. King, R. Sutherby, J. Been

With thousands of kilometers of buried oil and gas pipelines throughout the country, carrying flammable, high-energy hydrocarbons, the integrity and safety of this transportation and distribution network are paramount. The pipeline industry has the primary responsibility for pipeline safety and has in many ways taken the lead in dealing with safety issues. Over recent years, regulatory demands have increased, requiring operators to comprehensively evaluate their pipelines through indirect and direct inspections and to manage risk through integrity programs. Mechanistic and correlative models have been developed that assist in the prediction of pipeline integrity and the determination of reassessment intervals. These lifetime prediction models are based on decades of laboratory research as well as pipeline operating data, material data, and field monitoring data pertaining to soil conditions and CP. An overview is presented of an integrated approach towards the development of such models for the evaluation of external cracking and corrosion of transmission lines.

Jan 1, 2005

"In 2000 the CIM Council approved the CIM Standards on Mineral Resources and Reserves – Definitions and Guidelines, developed by the CIM Standing Committee on Reserve Definitions. The Definition Standards established definitions and guidelines for the reporting of exploration information, mineral resources and mineral reserves in Canada. The Mineral Resource and Mineral Reserve definitions are incorporated, by reference, in National Instrument 43-101, Standards of Disclosure for Mineral Projects, which came into force in Canada in February 2001 and was amended in December 2005.CIM DEFINITION STANDARDS- For Mineral Resources and Mineral ReservesPrepared by the CIM Standing Committee on Reserve DefinitionsAdopted by CIM Council on December 11, 2005FOREWORDCIM Council, on August 20, 2000, approved the ""CIM Standards on Mineral Resources andReserves - Definitions and Guidelines,"" developed by the CIM Standing Committee on ReserveDefinitions. The CIM Definition Standards on Mineral Resources and Reserves (CIM DefinitionStandards) establish definitions and guidelines for the reporting of exploration information,mineral resources and mineral reserves in Canada. The Mineral Resource and Mineral Reservedefinitions were incorporated, by reference, in National Instrument 43-101 - Standards ofDisclosure for Mineral Projects (NI 43-101), which became effective February 1, 2001.At the August 20, 2000 Council meeting a new CIM Standing Committee on ReserveDefinitions was established consisting of the following: John Postle, Bernie Haystead, LarryCochrane, Normand Champigny, Mike Hoffman, Colin McKenny, Jack Mullins, Phil Olson,Fred Payne, Jody Todd and Joe Ringwald.Subsequent to the publishing of the August 20, 2000 CIM Standards on Mineral Resourcesand Reserves, various CIM committees have compiled and published more extensivedocumentation on mining industry standard practices for estimating Mineral Resources andMineral Reserves. These standard practices provide more detailed guidance than that containedin the August 20, 2000 CIM Standards on Mineral Resources and Reserves. On November 14,2004 CIM Council adopted an update to the CIM Definition Standards to reflect the moredetailed guidance available and effect certain editorial changes required to maintain consistencywith current regulations. This version of the CIM Definition Standards includes further editorialchanges required to maintain compatibility with the new version of National Instrument 43-101which is expected to become law at the end of 2005. The CIM Definition Standards can beviewed on the CIM website at www.cim.org."

Jan 1, 2003

By W. Basuki, B. Setyotomo, L. Hakim, R. Hendrajaya

Due to high crack sensitivity of slab product of gas and oil line pipe application, its steel making process and alloy composition were evaluated and then improved to overcome its critical solidification process and reduced surface defects. The study was conducted at Slab Steel Plant Krakatau Steel. The purpose was to improve slab surface quality by reducing surface defects so that the slab surface doesn't need to be totally repaired. The method applied was by performing plant trial process, which the secondary process parameters such as alloying method and the casting parameters such as casting powder selection, metallurgical cooling, mould level control, and superheat were continuously monitored and then adjusted to the surface quality of the product. Based on the calculation of Ferrite potential of the steel, the chemical composition was designed to achieve optimum casting parameters in order to avoid high shrinkage during solidification. The results of the study are decreased surface defect quantity, and smooth casting process. The quantity of crack decreased by almost 90%. The slab surface repairing was significantly reduced from 85. % to less than 10%. These new casting parameters and developed alloy composition are then used and standardized for the mass production of the steel.

Jan 1, 2005

By Laxman (Lucky) Amaratunga, Hisham Madi

Final disposal of mine wastewater neutralization sludge continues to be one of more pressing problems in the mining industry. The disposal of mining and metallurgical waste products into underground reduces the environment impact and improves the safety of the mining operation and the economics of the enterprise. This current research focuses on an investigation of utilization of mine wastewater neutralization sludge obtained from Kidd Creek Mine site, as a supplementary material for their proposed deep mine pastefill system. Their proposed pastefill consist of combination of rock aggregate in a matrix of imported sand and tailings with binder (Portland cement + Slag cement). Pastefill mixes containing various percentages of the waste sludge 0 (control mix), 1, 2, 3, and 5% by weight as replacement to the fine sand were prepared and tested with different percentages of binder. Hypothesis behind this approach is to study the behavior of sludge as replacement of sand in matrix as well as its ability to act as a binder. Compressive strength, percentage of sludge, binder dosage, slump, water to cement ratio, percentage of solid, and curing time are being observed. The results indicated that sludge can be incorporated into the pastefill and enhance its strength without compromising the pastefill quality and integrity.

Jan 1, 2004

By M. Reza Bateni, M. Zandrahimi, J. A. Szpunar

Titanium aluminides and nickel aluminides offer the potentials, as coating materials, for high temperature and aerospace applications. In this research, attempt has been made to develop Al-Ti and Ni-Al intermetallic compound coatings on the surface of Inconel 738. The coatings applied through pack cementation and simultaneous diffusion annealing processes. Scanning-electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDAX) and grazing angle X-ray diffraction were used for evaluating of coating structure. It was demonstrated that the pack cementation technique could be used to develop TiAl3 and AlNi intermetallic compounds coating on Inconel 738 substrate. When pack cementation technique is based on a halide-activated pack with aluminum and titanium powders, the coating consists of TiAl3 intermetallic compound phase. Whereas, by pack aluminization of Inconel 738, the coating consists of AlNi intermetallic compound phase.

Jan 1, 2004

By Jonathan Tsang, Ali Merati, Jonathan Beddoes

Due to economic factors, many aircraft in service today have been operating for more than 30 years even though they were initially designed with a service life of 20 years. Improved damage management models are therefore needed for use in life prediction and management of the aging fleets of aircraft. Currently, the generally accepted procedure in fatigue life prediction methodologies is to back calculate the equivalent initial flaw size (EIFS) using established long crack growth data. However, it was observed from studies carried out at the National Research Council Canada that nucleation and short crack growth constitute up to -95% of the fatigue life. As a result, it seems that the significance of the short crack regime has been underestimated and must be further investigated and fully understood before an accurate holistic life prediction methodology can be realized. Unlike long cracks, local microstructural features such as grain boundary, grain size, inter-particle spacing, and texture play dominant roles in the behavior of short cracks. An extensive study has been carried out to evaluate different crack detection and monitoring techniques in the short crack regime for AA2024-T3. The results will be presented in detail.

Jan 1, 2004

By M. X. Yao, Y. Ning, P. C. Patnaik, R. Liu, X. J. Wu

Stellite 712 composites were developed with the reinforcement of bare TiC or Ni-coated TiC particles using HIPing powder consolidation technique. The emphasis of this research was on the effect of the Ni coating on the TiC particles and the HIPing conditions on the microstructure and performance of the composites. Calorimetric effects of the mixed composite powders were investigated using the differential scanning calorimetry (DSC) technique before the HIPing process, which provided the basis of the HIPing cycles designed. The microstructures of the composites were examined using SEM with EDX. The hardness and wear resistance of the materials were evaluated respectively. It was found that the HIPing temperature influenced the microstructure and the performance of the materials. The Ni coating on the TiC particle has improved the fracture toughness of the composites, but detracted the wear resistance. The experimental results and relevant mechanisms were discussed.

Jan 1, 2004