Search Documents

By O. -J. Siljan

"Refractory materials are an integral part of aluminium production. One special feature of aluminium making is the prominent role of sodium in all parts of the production process. This presence of sodium inflicts stresses on the refractory materials through reactions and may cause severe damages to the refractory linings. The present paper address possible reactions between sodium and refractories in anode bake furnaces, electrolytic pots and casting furnaces. The discussions presented in the paper points to the importance of selecting materials with excellent alkali resistance in all parts of the aluminium making process, although alkali resistance is not the sole parameter to determine refractory life-time. ""Acid"", i.e. silica-rich alumino-silicate refractories are shown to be the best materials for aluminium electrolysis cell potlinings, whereas high- alumina refractories based on minerals like andalusite seems to be the preferred choice for anode bake furnaces as well as cast house furnaces."

Jan 1, 2004

By T. Watanabe, M. Nakagawa, K. Kimapong

Ultrasonic wave was irradiated on metal surface in water to introduce compressive residual stress. The ultrasonic wave that was oscillated with 19.5 kHz ultrasonic transducer and amplified with a step type horn was irradiated. Slight plastic deformation occurred at the surface region of pure metal such as Cu and compressive residual stress was introduced. It seemed that the plastically deformed depth from the metal surface corresponded approximately to the depth of introduced residual stress. The higher compressive residual stress could be introduced into the surface of Cu-Zn brass and SUS304 stainless steel because work-hardening was simultaneously induced to those alloys. Furthermore, since martensitic transformation was induced by the plastic deformation in the case of SUS304, the compressive residual stress could be introduced more deeply into the surface region. The residual stress of SUS304 reached to the maximum value of 574 MPa by irradiating for 5min.

Jan 1, 2004

By R. Abel

During the last eight years, the Ventanas electrolytic refinery has been improving its results by applying a series of new operational practices, such as the reduction of electrode spacing from 115 mm to 105 mm., raising the current density to 305 A/m2, modification in the operators shifts to about 70% of the workers, reducing the pulling cycles by two hours, and the erection of a new anode preparation machine. These improvements allowed an increase in the refinery capacity from 323,000 to 382,000 metric tons of electrolytic copper per year. In the same period it has obtained certification under the ISO 9001:2000 and ISO 14001:2004 standards. All of these developments have been achieved using conventional technology with copper starting sheets. The continuous improvement that is covered in this paper has allowed Ventanas to optimize its production, costs, and operational results. For the next years, it is planned to follow the same tendency, bringing the productivity of the plant to higher levels.

Jan 1, 2007

By K. Madi, E. Yeugo Fogaing, S. Forest, M. Boussuge, L. Massard, M. Huger, Gaultm C.

This study has been carried out owing to the French research program PROMETHEREF, which aims to improve the knowledge of thermal and mechanical properties of industrial refractories at high temperature. In this frame, this paper relates a collaborative study between Saint-Gobain CREE, R&D Centre for Saint-Gobain Ceramics & Plastics in Europe (Cavaillon), the Materials Center P.M. Fourt of Ecole des Mines de Paris (Evry) and the Research Group on Heterogeneous Materials (GEMH) of ENSCI (Limoges). Data collected at high temperatures by using different means (bending tests, ultrasonic measurements,...) allows the identification of the high temperature behavior of two fused cast materials, produced by Saint-Gobain group for the glass manufacturing industry. The results emphasize the importance of the transformation of zirconia and of the viscosity of the glassy intergranular phase on the mechanical behavior. Damage under the form of microcracking caused by thermal expansion mismatch between the phases is also observed during cooling down at low temperature, when the material is elastic.

Jan 1, 2004

By Apoorva Bajaj

Iron ore mines of Steel Authority of India Limited (SAIL) have to comply with strict chemical composition norms laid down for iron ore lumps supplied to its steel plants. This requires a careful planning of the overall ore excavation operation. In general terms, the problem can be stated as: Given the chemical composition of ore for all excavation sites, excavation capacity of each shovel, distance of each excavation site from the crushing plant and the number of dumpers available for transport of the ore, find out the percentage of ore to be excavated from each excavation site such that the production rate is maximized and the chemical composition norm is satisfied to the best possible extent. This paper presents an approach to solve this problem using Branch and Bound method. The specification for r.o.m. quality has been modified by incorporating a new parameter, ?Al2O3 / SiO2? ratio, which has a significant effect on the performance of iron blast furnace.

Oct 1, 2009

By C. J. Cattarello

"The Langmuir Mine is located seventeen miles south-east of South Porcupine in Langmuir Township.The property was developed as a Joint Venture between Noranda Mines Limited and the International Nickel Company of Canada with Noranda responsible for the operation of the property.The Mine came into production in June 1973 at a rate of 700 tons per day of nickel ore.MINING The mining method selected for the Langmuir Project was a sub-level retreat method. This consisted of driving sub-levels longitudinally in the ore body at 35 foot, intervals with the sub-levels being connected by a ramp from each main level for the use of trackless mining equipment.GENERAL GEOLOGY OF THE LANGMUIR MINE The deposit is situated about 1,000 feet west of the shore of Carmen Bay at the south of Nighthawk Lake in Langmuir Township. The area is underlain by andesite and rhyolite flows with iron formations which are intruded by gabbro, diorite, peridotite and late precambrian diabase dikes."

Jan 1, 1975

By David L. Sprott

This paper presents an evaluation of underground-to-surface haulage options for a relatively large deposit. Specifically, it presents a recommended haulage option to provide the greatest value to the Project. Options considered included conventional truck, trolley-truck, conveying and shaft hoisting. The work was done at the level of a preliminary assessment as input to an internal pre-feasibility study. The Base Case for the analysis in this study was a Long Hole Open Stoping option (LHOS) using conventional truck haulage. Two scenarios were considered for the evaluation and included: 1. The current resource to ~700 m depth. 2. An expanded resource to ~825 m depth. The haulage options evaluated included three trucking options, three conveyor options and two shaft options. The paper presents the results from evaluating these options within the two mining scenarios using a Discounted Project Cost (DPC) comparison. Recommendations are made for the options that will provide the greatest overall value to the project.

May 1, 2008

By Heinrich Möller

The electro-oxidation of 0.1 M ethylene glycol at gold, platinum and gold-platinum alloy electrodes in different heat treatment conditions has been studied in 0.5 M NaOH, at room temperature. Poisoning of all the electrodes occurs. However, the alloy electrodes poison at a faster rate than the pure gold and platinum electrodes. This indicates that the initially higher activity of these electrodes cannot be the result of decreased poisoning through a "third-body" effect.

Oct 1, 2003

By B. D. Wood, J. A. Fowler, H. S. Grütter, J. M. Kong

Abstract- The phased approach used by De Beers for diamond exploration is briefly outlined. The Victor kimberlite is one of 19 kimberlites in a cluster near Attawapiskat, Ontario. The progress at the Victor kimberlite is summarized, and the operations are described within the framework of this staged approach. An evaluation program is currently under way on the Victor kimberlite, but although results are encouraging, insufficient diamonds have been recovered to permit disclosure of estimates for the grade and value.

Jan 1, 2001

By J. C. Glandus, N. Tessier-Doyen, M. Huger

The Young's modulus of bi-phased model materials (vitreous matrix containing spherical alumina inclusions) have been determined by two complementary approaches: experimental and analytical. If the matrix and inclusions exhibit close coefficients of thermal expansion, the experimental results lie in the vicinity of the lower bound of the Hashin & Shtrikman's model. If there is a dilatometric disagreement between the components, untypical behaviors, similar to those obtained for a family of industrial refractory materials, were observed when the temperature varies.

Jan 1, 2004

By C. Sideco

"Concentrate drying at the Sullivan Concentrator goes back to 1937 when the original coal-fired dryer was put into operation. This was a second hand 8' dia. x 56' long Struthers-Wells rotary dryer that came from the phosphate plant in Warfield, B.C.In 1962, replacement of the old dryer was seriously considered. The shell and the auxiliary drive mechanism were badly worn and needed replacing. In April 1963, the new 8' dia. x 65' long fuel oil-fired Struthers-Wells dryer went in operation at an installed cost of $174,000.In 1965, it was apparent that a major rebuilding of the dust collecting system would have to be done. A study was carried out and a Ducon Dynamic Gas Scrubber was installed. The system went in operation in November 1966 and has fully met expectations.In the same year, the zinc dryer was converted from fuel oil to natural gas. The conversion has resulted in savings in fuel cost of 12 to 15%.Frame No. 1Zinc Dryer PerformanceDryer Make - Struthers-WellsDryer Size 3/4 8' dia. x 65' long Drum Drive - 100 HPSpeed of Rotation - 5 RPMFeed Rate - 50-65 TPHFeed Moisture - 10-12%Discharge Moisture - 4-6%Dryer Inlet Temperature - 1600-1800°F Dryer Outlet Temperature - 200-250°F Stack Gas Volume - 25,000-40,000 CFNDust Collecting Efficiency - 99.75-99.98% Duet Loss in Stack - 50-300 lbs./day"

Jan 1, 1972

Adaptive Processing as proposed in geometallurgy has to rely on spatially interpolated information on geometallurgical parameters like phase composition, size distributions of particles of different phases, grain shape parameters, and portions of value elements in different grains. Using the geostatistically predicted values for adaptive processing, e.g. for the selection of milling diameters, thresholds in physical separation, or choices on using an extra pre-separation step, is typically not optimal. Mathematically this effect is introduced by two forms of nonlinearities: 1) The nonlinear scales of compositions, distributions, and shapes have special properties with respect to geostatistics. Classical geostatistics creates some artefacts for these nonlinear scales. On the other hand, modern geostatistical procedures adapted to these scales do not provide unbiased results with respect to linear transformations of the data (e.g. biased block estimates). 2) Neither economic nor ecological effects (e.g. monetary gain) of processing decisions are linear in the interpolated geometallurgical parameters. These nonlinear transforms are not unbiasedly estimated by the likewise transformed unbiased geostatistical predictions of the geometallurgical parameters. Furthermore, we need to optimize the conditional expectation of the gain, rather than obtain an unbiased estimate. Standard geostatistics as such does not provide the "right sort" of estimates for adaptive processing. A nonlinear kriging procedure is needed to approximate the nonlinearities mentioned before. We propose to solve these problems simultaneously using a nonlinear geostatistical technique for predicting the target function (the monetary gain), rather than to predict the geometallurgical parameters and compute the gain from them. The optimization can then be performed directly on this estimated function. It can be shown that this optimization performed on the conditional expectations, not on unbiased predictions, would yield the best possible processing choice. We propose a procedure choosing the processing parameters on an approximation of the conditional expectation. The difficulties with the classical approach and the effectiveness of this new approach are illustrated by a simplified simulation example with a single processing parameter and a simple dependence on the microstructure.

Aug 1, 2013

By G. D. Hibbard

New regions of material property space can be accessed by combining microstructural design at the nm-scale with architectural design at the µm- or mm-scale. In the first case, large strength increases associated with grain size reduction to below 50 nm have driven extensive research efforts into the development of nanocrystalline materials [e.g. 1-3]. For many potential structural applications, however, the density of a nanocrystalline material is just as important as its strength. In fact, reducing the density is more important than increasing the strength for certain weight specific materials performance indices, and it is especially critical for applying structural nanomaterials in the aerospace and automotive sectors. We have developed a new type of structural nanomaterial wherein the effective density of the parent metal is reduced by more than an order of magnitude by incorporating an internal periodic cellular architecture of open space. In one example a low density cellular nanocrystalline material was created by electroforming nanocrystalline Ni around a rapid-prototyped acrylic photopolymer microtruss, Figure 1 [4]. Microtruss materials have periodic cellular architectures that are specifically designed to undergo stretching-dominated deformation as opposed to the bending-dominated deformation in conventional open cell metal foams [5,6]. This new cellular nanocrystalline hybrid material combined the structural efficiency of microtruss architectures with the ultra-high strength that can be achieved by grain size reduction to the nm-scale. Although it played a critical role as a cathode support during the initial stages of nanocrystalline electrodeposition, the polymer core did not contribute significantly to the inelastic buckling resistance of the composite metal/polymer struts and it may therefore be desirable to remove it post deposition by means of chemical dissolution or thermal decomposition [4]. Nanocrystalline electrodeposition can also be used to reinforce conventional cellular metals (Figure 2), creating new types of cellular composites such as metal/metal microtruss hybrids [7-10] and metal/metal foam hybrids [11,12]. For example, nanocrystalline Ni-Fe alloy sleeve thicknesses of up to 400 µm were used to reinforce an aluminum alloy microtruss that had been fabricated using a stretch-bend approach; the nanocrystalline sleeves had the effect of increasing the microtruss strength by up to a factor of twelve and the specific strength by a factor of three [8]. Alternatively, much thinner sleeves can be electroplated to produce structural coatings. In one example, a nanocrystalline Ni coating was designed to provide both corrosion protection and inelastic buckling resistance [10]. Because the ultra-high strength material was optimally located at the furthest distance from the neutral bending axis, only a thin coating of 50 µm was needed to double the inelastic buckling resistance of the 1.13 mm x 0.63 mm cross-section plain carbon steel struts [10]. Overall, the mechanical performance increase that can be obtained through electrodeposition depends on a complex interaction between the starting cellular architecture and the nanocrystalline sleeves.

Jan 1, 2010

By Jian Li, V. Y. Gertsman, David C. Katz, M. Elboujdaini

Analysis of stress corrosion cracking (SCC) usually involves high-end analytical tools including scanning electron microscope (SEM) and analytical transmission electron microscope (TEM). In recent years, focused ion beam microscope (FIB) has found many applications in materials science fields. In this study, high-resolution FIB images have shown details of crack morphology and a plan-view TEM specimen containing the selected crack-tip was successfully prepared. The preparation of cross-sectioned samples containing crack tips was of paramount importance for subsequent TEM analyses.

Jan 1, 2004

THIS article describes the origin and details of a hydraulically operated switch to control the operation of an automatic underground pumping system. This system was installed in December, 1939, on the 2,350-foot level at No. 5 shaft of the Buffalo Ankerite mine. The pumping unit consists of an 8-stage centrifugal pump direct-connected to a 150 h .p., 2,200 volt motor. Pumping capacity is 200 gallons per minute under a 1,315-foot head and with a flooded suction. The control consists of a 200 amp., 2,200 volt oil-immersed starter with thermal overload protection, thermal protection on the pump, and a flow switch that is bypassed for 30 seconds after the pump starts. The 30-second time lag is operated by a relay mounted on the panel. There is a swing check valve in the discharge line of the pump which originally operated the flow switch by means of a connected outside lever which closed the switch as the check valve opened.

Jan 1, 1945

By Kostas Fytas

Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian Mining Industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage phenomenon. AMD occurs when sulphide minerals (ex. pyrite) contained in rock are exposed to air and water and subsequently oxidize to produce low pH water. This acid effluent has the potential to mobilize any heavy metals contained in the rock. Coating the sulphide minerals with silicates is a new promising technology to reduce AMD. Pyrite is treated with a solution containing H2O2, sodium silicate and a buffering agent. H2O2 oxidizes a small part of pyrite producing ferric iron (Fe3+) ions. These ions subsequently react with the silicate ions to produce ferric hydroxide-silica that precipitates on the pyrite surface producing a passive coating. This silicate coating can protect the grains of pyrite from oxidation. This paper presents a series of experiments that confirm that silicate coating can considerably reduce AMD.

May 1, 2001

By V. Ramachandran

The successful advent of solvent extraction (SX) reagents for copper recovery and improvements in electrowinning of copper to produce LME grade A copper cathode have paved the way for the hydrometallurgical treatment of copper oxide and low grade sulfide ores. This has resulted in about 25-30% of the world's copper being produced today by the Leach-SX-EW process. The obvious next step was to develop processes for the hydrometallurgical treatment of copper sulfide concentrates, as an alternative to a typical smelter-refinery complex. The current paper updates the processes that have been developed to date with emphasis on processes that are being commercialized or that are seriously under consideration for commercialization. Most of the discussions relate to the hydrometallurgy of chalcopyrite concentrates, which account for about 70% of the world's known copper reserves. In summary, in the last thirty years, the hydrometallurgical treatment of copper sulfide concentrates has attained full maturity and will be a serious option to contend with while evaluating any future new copper plant.

Jan 1, 2007

By Christopher W. N. Anderson

Induced hyperaccumulation of gold by plants was first reported in 1998 by researchers from Massey University in New Zealand who proposed the idea of mining gold using plants (phytomining). Since that time research has been conducted to understand the conditions under which plants can be made to take up economic amounts of the metal. One key focus has been on the geochemistry of gold-rich soils, leading to a diagnostic test that can predict how suitable a particular soil might be to gold phytomining. Field trials have been conducted at several locations around the world in collaboration with industry partners. A Decision Support System has been developed to assist in the design and management of phytomining operations, and economic modeling has been carried out to set targets levels for phytomining technology. Novel studies are now examining the form of gold in plants. Research suggests that plants may store gold as discrete metallic nanoparticles in leaf and stem tissues, an observation that may lead to new ways to recover the metal from harvested biomass.

Oct 1, 2003

By J. A. Hurd

Towards the goal of a better understanding of the structure-proton conductivity relationship in PEM materials, this project concerns the design of ordered polymeric solids containing well-defined sulfonate aggregates. The approach employed involves the templation of sulfonated monomers using core principles of crystal engineering. In addition to sulfonate groups, the monomeric units contain crosslinkable functionalities to enable formation of a covalently linked network. The templation strongly directs the construction of well-defined sulfonate clusters and aggregates. Structural, sorption and conductivity data for the networks will be shown.

Jan 1, 2005

By Premil Agarwal, Alok R. Patnaik, Pulak Dhar, Prakash C. Patnaik

In this study, a physics based model has been presented, considering the growth of the thermally grown oxide (TGO) layer on the bond coating of a thermal barrier coating. Using diffusion equations, a model has been developed to physically describe the oxidation process. The mathematical equations representing the diffusion formulations have been solved numerically. The computed results show the depletion of Al in the bond coating as it diffuses both towards the super-alloy substrate and towards the TGO produced in between the bond coating and the ceramic TBC top layer.

Jan 1, 2004