Search Documents

By H. R. Appell

The Bureau of Mines studied the conversion of a variety of cellulosic wastes, for example, sawdust, bovine manure, sewage sludge, urban refuse (free of metal and ceramics), etc., to heavy oils. The objective of the investigation was to determine the scope of the reaction and elucidate the chemistry involved. The reactions took place in the presence of synthesis gas and water or carbon monoxide and water under conditions of elevated temperatures and pressures. Waste conversions above 90 pct, often near 99 pct, with oil yields in the range of 40 to 60 pct, were obtained in the temperature range of 250° to 425° C and pressure range of 1,500 to 4,000 psig. Because mild conditions were sought, most of the experiments were conducted at temperatures of 250° to 350° C and pressures of 1,500 to 3,000 psig. In general, lower viscosity products were obtained at higher reaction temperatures. Conversions and oil yields were significantly increased by operating in the presence of a high-boiling oil; either anthracene oil or oil recycled from the process was satisfactory. Synthesis gas containing 50 pct carbon monoxide gave satisfactory results as a replacement for carbon monoxide. Cobalt molybdate on alumina catalyst, used with sodium carbonate, gave a product of lower viscosity and lower oxygen content than sodium carbonate used as the sole catalyst. The waste-to-oil process has been successfully investigated in continuous flow equipment as well as in batch autoclaves.

Jan 1, 1975

By George S. Rice, J. W. Paull, R. R. Sayers

"Standard rock dust for use in the rock dusting of coal mines might be defined tentatively as powdered mineral, light colored and free of carbonaceous matter and free silica, all of which will pass a 20-mesh screen while 50% of it will pass-through a 200-mesh screen.Such dust may be prepared from limestone, gypsum, anhydrite, or shale free of sand and flint. For the initial rock dusting of the average nongaseous bituminous mines enough standard rock dust should be applied so that the combustible content of the resulting mixture of rook dust with mine dust shall not exceed 45%, a range somewhere between 35% end 45% being the practical objective sought.All entries, slopes or passageways and room necks should be rock dusted.Additional safeguards are:a.,Rockdusting roomsb.,Scattering of dust in vicinity of shots before firing.c.,Placing of barriers in the mouths of panels, cross-entries and other key positions.Redusting becomes necessary whenever the combustible content of the mine dust exceeds the permissible maximum. This should be determined by regular, systematic sampling, followed by a simple analysis of the samples for combustible content. A Bureau of Mines volumeter for measuring the density can be used for the determination of combustible content."

May 1, 1924

By M. M. Gilkey

This report describes the effects of water shortage on Arizona's mineral industries. The information presented was obtained in interviews with company representatives. Operations covered included all State metal mines using substantial quantities of water and all concentrators and smelters. Also included in the survey were 8 operations in the nonmetallic group; 22 in the plating, metal-fabricating, and metal-forming categories; 1 public-utility power company; and 6 water companies. The extent of the water shortage in Arizona is reflected in mineral- industry water-use practices, in the high cost and low quality of water used at many operations, and in the stringency of State control of well drilling and pumping. Many mineral-industry operations are among those users most seriously affected by the uneven water supply.

Jan 1, 1963

By G. L. Gates

Five possible sources of water for waterflooding of petroleum reservoirs in the arid San Joaquin Valley of California were considered. Three of them (water produced with petroleum, water from a shallow saline aquifer, and waste irrigation water) were analyzed chemically; laboratory information for one (sea water) had been developed during a previous study. A series of laboratory tests made on the fifth source (fresh water) determined the solubility of calcium sulfate dihydrate in water. Laboratory analyses included the following: Chemical analyses of water produced with petroleum and waste irrigation water; solubility of calcium sulfate dihydrate in water and brines; the effect of excess sulfate on the solubility of calcium sulfate in brines; the presence of sulfate-reducing bacteria; and the permeability of cores from a petroleum reservoir to air, to water from other petroleum reservoirs, and to waste irrigation water. The results showed that most of the waters and mixtures of waters are compatible with petroleum reservoir waters and are generally suitable for injection. The calcium content of some of the formation waters is quite high, and care must be taken to prevent precipitation of calcium sulfate dihydrate. The permeability of the few cores tested was about the same to water and brines as to air, indicating that formation damage due to clay swelling will not be serious. The waters most likely to be available for injection are water produced with petroleum, water from shallow saline aquifers, and waste irrigation water.

Jan 1, 1970

By C. A. Herbert

Information Circular 6746 reviewed the fatalities in Indiana coal mines. for the fiscal year October 1, 1951 to September 30, 1933. Since then Indiana has changed its fiscal year to the period July 1 to June 30, but as most statistical data on accidents are arranged according to calendar years, the data in this paper are for the last 3 months of 1932 and the calendar year 1933, rather than for the new Indiana fiscal year. Tables 1 and 2 list the fatalities in Indiana coal mines3/ by cause and occupation for the last 3 months of 1932 and for the calendar year 1933. The fatalities for the small wagon mines employing fewer than 10 men are separated from those employing 10 or more men to call attention to the ex- tremely high fatality rate in small mines, largely because the State mining law does not apply to them nor do they come under the jurisdiction of the Indiana mine inspectors; as a result health and safety conditions are ex- tremely bad. During the last 3 months of 1932, 5 (approximately 42 percent of the total) fatalities occurred in the small mines, while for the calendar year 1933, 12 (approximately 32 percent) of the fatalities occurred in them. The Indiana Division of Mines and Kining estimates that these small mines have an annual production of approximately 325,000 tons, or about 4.5 percent of the total coal-mine production of the State. In other words, for these small mines the fatality rate per tons mined during 1933 was about 10 times as great as for the mines employing 10 or more men. Another lamentable feature in connection with the fatalities in small mines is that very few carry any compensation insurance and the owners are not worth enough financially for dependents of victims to collect anything under the common law; as a result, the dependents of those killed usually are left penniless and subjects of public charity.

Feb 1, 1935

By M. M. Gilkey

This report describes the effects of water shortage on Arizona's mineral industries. The information presented was obtained in interviews with company representatives. Operations covered included all State metal mines using substantial quantities of water and all concentrators and smelters. Also included in the survey were 8 operations in the nonmetallic group; 22 in the plating, metal-fabricating, and metal-forming categories; 1 public-utility power company; and 6 water companies. The extent of the water shortage in Arizona is reflected in mineral- industry water-use practices, in the high cost and low quality of water used at many operations, and in the stringency of State control of well drilling and pumping. Many mineral-industry operations are among those users most seriously affected by the uneven water supply.

Jan 1, 1963

By L. K. Weaver

The purposes of this Bureau of Mines report are to review the history of the domestic offshore hydrocarbon production; to project offshore oil and lease condensate production from 1971 through 1985; and to show the impact of offshore development on the onshore segment of the petroleum industry. Since 1954, offshore production has provided an increasingly larger portion of the domestic oil production. Domestic offshore oil and lease condensate production has increased from about 2.0 pct of the U.S. total in 1954 to 16.7 pct in 1970. Likewise, marketed gas production has increased from 1.0 pct of the U.S. total in 1954 to 15.0 pct in 1970. The past performance of exploration, leasing, development, and production of the offshore petroleum industry was used to make projections of offshore oil production. A comparison between onshore and offshore operations was also made. Assuming a tentative Department of the Interior offshore leasing schedule is completed by 1980, the authors estimate that by 1985, about 30 pct of domestic crude oil and lease condensate production from the lower 48 States will come from offshore areas. Currently, leasing of Federal offshore areas has been delayed due to environmental considerations. The rate at which off-shore hydrocarbons will enter the energy market will depend, to a large extent, on how soon environmental considerations are resolved. Assuming that offshore leasing will resume in the near future, U.S. offshore production of crude oil and lease condensate should be about 934 million barrels in 1985.

Jan 1, 1973

Rapidly identify unstable mine waste embankments and similar dam structures. Approach Aerial photography, geotechnical instrumentation, and telephone or satellite data transmission are used to supplement walk-around inspect ions. How It Works Embankment stability and other indicators of structural integrity are evaluated using aerial photography, and on-site unattended instruments and data transmitting systems. Evidence of external movement and water seepage is obtained from aerial photography and photogrammetric evaluation techniques. Surface points marked by stake- mounted targets are monitored photographically at time intervals of several weeks or months. Photographic measurements of x, y, and z coordinates of these points are obtained from flying a series of photo-runs over the dam.

Jan 1, 1979

By Forrest T. Moyer

Injury experience at metal mines and mills (excluding officeworkers) in 1964 was 60 fatal and 3,672 nonfatal disabling work injuries during an exposure time of 149 million man-hours worked. These injuries occurred at a frequency rate of 24.57 per million man-hours and had a severity rate of 3,687 days lost or charged per million man-hours. Employment at 2,363 metal mines and 291 mills, excluding officeworkers, was 68,140 men in 1964. The average number of days worked was 274 The principal cause of fatal injuries at all mines and mills was haulage accidents and in underground mines, only, was falls of ground. The principal cause of nonfatal injuries was handling material accidents. The frequency rate at metal mines and mills in 1964 was slightly below that of 1963, whereas the severity rate was higher. Injury experience at 94 primary nonferrous smelters, refineries, and reduction plants (excluding officeworkers) was 8 fatal and 999 nonfatal disabling work injuries during a worktime of 98 million man-hours worked. The combined injury-frequency rate in 1964 was 10.29 and the injury-severity rate was 1,005. The 36,956 employees worked an average of 329 days during 1964. The principal cause of injuries at these plants was handling material accidents.

Jan 1, 1968

By Raymond O. Dannenberg

The Bureau of Mines conducted laboratory and full-scale tests to develop a process for improving the flotation characteristics of lime-treated waste water produced by the Kennecott Copper Corp., Magna, UT. Unknown substances in the waste water reduced the flotation efficiency of the metal sulfides. An estimated annual loss of 795,000 lb Cu, 232,000 lb Mo, 5,625 tr oz Ag, and 617 tr oz Au would result from recycling the total flow from the lime treatment plant to the flotation mill in an effort to conserve water and reduce associated expense. The tests indicated that aeration or treatment with activated carbon significantly improved the water quality. The improvements in molybdenum recovery averaged 8 pct for carbon, 11 pet for activated carbon, and 16 pct for combined aeration and activated carbon. The combination of the two processes produced water quality as good as or better than normal feed water.

Jan 1, 2011

By P. E. Churchward

Rhenium sources and recovery methods were investigated by the Bureau of Mines to delineate potential resources of the metal. The only significant rhenium resource appears to be about 28,000 lb of rhenium contained in the domestic annual output of approximately 20,000 tons of byproduct molybdenite concentrates from porphyry copper operations. An estimated 70 to 80 pct of this rhenium is potentially recoverable by processing the rhenium-bearing fumes and dusts obtained during conventional roasting of molybdenite concentrate. At 70 pct recovery this would amount to 19,600 lb of rhenium. A more conservative estimate by the Committee on Refractory Metals of the National Research Council (1513 is that 12,000 lb of rhenium metal could be produced annually from current production of molybdenite from porphyry copper operations in the United States. A procedure was developed in the laboratory for recovering rhenium in the form of electrolytic flake by electrowinning the metal from a solvent extraction strip solution. The procedure included (1) water leaching of molybdenite roaster flue dust, (2) selective extraction of rhenium from the leach liquor by contacting it with a kerosine solution of a quaternary amine, (3) stripping of rhenium from the loaded organic solution by a perchloric acid solution, and (4) electrodeposition of rhenium from the loaded strip liquor. Raw material for the studies was flue dust containing 0.48 pct Re, 35 pct Mo, and 23 pct S in sulfide and sulfate form, and small amounts of numerous metallic impurities. Water leaching dissolved 85 pct of the Re and yielded a solution that was 13 in sulfuric acid and contained, 1 g/l Re and 16 g/l Mo. The solvent extraction strip solution that was electrolyzed for rhenium deposition was 1 molar in perchloric acid and 1 molar in ammonium sulfate and contained 13 g/l Re and 0.01 g/l Mo.

Jan 1, 1963

By D. F. Hambley

This report documents the work carried out by Engineers International, Inc. and its subcontructor, W. G. Pariseau, in order to develop a design manual for ore passes for open pit mines. The work included an extensive information search, novel analyses in rock flow theory, cost and time estimation for shaft and raise construction methods, and development of design criteria for the are pass proper, dump point, and draw point.

Jan 1, 1983

The principal activities of the Bureau of Mines Explosives Research Center (now Safety Research Center) during fiscal year 1968 (July 1, 1967, to June 30, 1968) are reviewed in part 1. Part 2 presents short abstracts of the publications issued during this period in the Bureau series and in other media. Part 3 describes a short study on the thermal decomposition of RDX and HMX not destined for publication elsewhere. ACKNOWLEDGMENTS The Bureau gratefully acknowledges the support received through cooperative agreement in fiscal year 1968 from The Manufacturing Chemists Association.

Jan 1, 1970

By Franklin H. Persse

To meet escalating energy requirements, substantial increases in production from the strippable coal and lignite deposits in eastern Montana, western North Dakota, and northeastern Wyoming already have occurred, and further expansions are expected at least until the year 2000. Such production, attributable largely to rising demand for low-sulfur coal, must be accomplished with a minimum of adverse effects on the environment. Information on geology, climate, and current land use in the Upper Missouri River basin is presented in the Bureau of Mines review as a guideline to what operators may expect during and after mining. Proven methods of protecting the air and water from pollution and of restoring mined land for other uses are described, and untried methods of land reclamation, some with equipment yet to be manufactured, are discussed as possible means of maintaining aesthetic values in the basin. Costs incurred to protect the environment are part of the production cost and thus are borne by the ultimate consumer. Unit production costs are less for the thick coal and lignite deposits of the basin than for the thinner but higher Btu coal deposits of the Eastern and Midwestern United States. Precise comparisons of environmental protection costs between mines in such disparate areas cannot be made, because of differences in physical conditions, accounting procedures, and other variables.

Jan 1, 1975

By N. C. Tomoeda, W. D. Bensema, J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 350 meters (1150 ft .) and 488 meters (1600 ft .) . The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broad- band, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or E layers of ionosphere as an upper plane and the earth as a lower plane. The measurement systems used are similar to those used earlier. The technique is to record broadband, analog signals, digitize the data, and use a fast- Fourier transform to obtain spectral plots. This tech- nique is novel in that it can measure simultaneously all magnetic field energy within a limited portion of the spectrum for a limited time, and, after processing, reproduce the events occurring in that time interval in great detail .

Jan 6, 1974

By J. H. Rose

This paper describing the milling practice at the Magma Copper Co., Superior, Ariz., is one of a series being prepared by the Bureau of Mines on milling methods and costs in the various mining districts throughout the United States. ACKNOWLEDGMENT The authors wish to acknowledge their indebtedness to William Koerner, general manager of the Magma Copper Co., for permission to prepare this article; to J. S. Garrott, former mill superintendent, for the historical facts; and to Walter Cooksley, general foreman, for his assistance in obtaining the data.

Jan 1, 1930

By Florence L. Feicht, H. H. Schrenk, Carlton E. Brown

This report describes the dropping - mercury electrode , its use in analysis , and the procedure of the Health Division of the Bureau of Mines in determining lead , cadmium , and zinc . The dropping - mercury electrode or polarograph is an electrolytic device , one electrode of which consists of mercury issuing in small drops from a capillary tube . Such electrodes have been in existence for more than 50 years, but they were not used for analytical purposes until about 1922.6/ Developments since have been rapid , especially in Czechoslovakia , Germany , Italy, and Japan and more recently in the United States . A recent bibliography / contains references to, 825 articles issued from 1903 through 1940. In 1939 Kolthoff and Lingane presented the first comprehensive critical review, in English , of the device and its use in analysis . They have recently issued a book on the same subject. Similar information also is included in a recent book10/ by Kolthoff and Laitinen . Much of the information in this and the two following sections on this device and its use in analysis was obtained from these three publications . The use of the dropping - mercury electrode in analysis is based upon the fact that the kind and amount of electro - reducible and electro - oxidizable constituents in solution can be determined from the current -voltage relationships revealed by this electrode or electrolytic device .

May 1, 1942

By Edward L. McHugh

The appraisal of mineral resources of the Challis National Forest, Idaho, by the U.S. Bureau of Mines, was made so that the mineral resources of the forest could be appropriately considered in land use planning. Information from this study is intended to help the U.S. Forest Service to incorporate mineral resource data into forest plans. The study was done in conjunction with the U.S. Geological Survey, which released a companion report on the geology and mineral potential of the Challis National Forest in 1989. Mineral development activity in and under the Challis National Forest has been of great economic significance to Idaho and the United States. Since the 1960's, mines within the forest have produced mineral commodities worth more than $590 million A current (1989) commodity prices. Identified mineral resources have a gross value of about $2 billion at current prices, including 8 strategic or critical minerals. The U.S. Bureau of Mines study identified and described 723 active and inactive mineral properties within the forest. Mineral properties with identified resources were evaluated to determine their economic significance, and an assessment was made of the feasibility of mineral development. Of the 2,516,191 acres in the Challis National Forest, about 390,000 acres were classified as having mining development interest commercially important mineral production, mainly of molybdenum, gold, and silver from the Challis National Forest is likely for the foreseeable future.

Jan 1, 1991

By R. D. Groves

Laboratory research has demonstrated that high - grade copper powders can be produced under controlled conditions from cement copper products . The technique should enable small producers to prepare a directly marketable product by means other than smelting and electrolytic purification . A continuous drum- type precipitator was the preferred unit for producing fine - sized particles of cement copper that were further processed by chemical digestion in a copper sulfate solution , by reduction and sintering in a hydrogen atmosphere , and by grinding to a powder . The effects of variables related to all stages of the process were investigated . Treatment of leach solutions from three different sources resulted in copper powders containing 99.2 to 99.8 pct Cu , apparent densities of 1.97 to 2.25 grams per cu cm , good powder flow rates , and a size distribution of 54.9 to 60.1 pct minus 325 - mesh material .

Jan 1, 1964

By Arno C. Fieldner

Six years ago, I addressed the annual meeting of the American Society for Testing Materials on "Fuels of Today and Tomorrow."3/ Since then, our country has been drawn into another great war of veritably global extent, with unprecedented demands on fuels, foods, and materials in general. My purpose in this address is to review the changes in fuel supply and demand since 1937 and to give you my views on the outlook for the future. CONDITIONS IN. 1237 Daring 1936 the United States produced and consumed one-third of the world production of coal, two-thirds of the petroleum, and about 95 percent of the natural gas. Two-thirds of the oil produced in all countries since the discovery well was drilled in 1859 had come from American wells. With the exception of the three depression years 1931, 1932, and 1933, new oil reserves were being discovered since 1924 well in excess of our increasing rate of consumption. Discoveries of natural gas, likewise, were tremendous in volume, and this fuel was being transported to most parts of the country by pipe lines; some of them more than 1,000 miles long. We had all kinds of mineral fuels in abundance and at prices that did not stint anyone in the maximum utilization of the mechanical devices that were being developed on every hand. No one suspected that the time might come in a few years when, gasoline would be doled out to some of us at the rate of 1-1/2 gallons a week or that many of our fuel-oil furnaces would have to be converted to burn coal. Of course, these restrictions are due to unusual war conditions, such as lack of coastwise tanker transportation, unprecedented demand for aviation gasoline, and the shortage of rubber for automotive tires. However, these shortages do call our attention to the vital part of petroleum reserves in our country's future position among nations. Therefore, it is of special interest to review briefly the relations of recent supply and demand with respect to our various mineral fuels.

Jan 1, 1943